MULTIQUIP WHISPERWATT DCA800SSK2 Guide

THIS MANUAL MUST ACCOMPANY THE EQUIPMENT AT ALL TIMES.
To find the latest revision of this
publication, visit our website at:
www.mqpower.com
WHISPERWATT™ SERIES
MODEL DCA800SSK2
60HZ GENERATOR (STD.)
(KOMATSU SAA6D170E-3 DIESEL ENGINE)
PARTS LIST NO. C5871301004
Revision # (09/03/09)
OPERATION AND PARTS MANUAL

PAGE 2 — DCA800SSK2 60 HZ GENERATOR • OPERATION AND PARTS MANUAL — REV. #0 (09/03/09)
PROPOSITION 65 WARNING
Diesel engine exhaust and some of

DCA800SSK2 60 HZ GENERATOR • OPERATION AND PARTS MANUAL — REV. #0 (09/03/09) — PAGE 3
If you believe that your vehicle has a defect that could cause a crash or could
cause injury or death, you should immediately inform the National Highway
Traffic Safety Administration (NHTSA) in addition to notifying Multiquip at
18004211244.
If NHTSA receives similar complaints, it may open an investigation, and if it
finds that a safety defect exists in a group of vehicles, it may order a recall and
remedy campaign. However, NHTSA cannot become involved in individual
problems between you, your dealer, or Multiquip.
To contact NHTSA, you may either call the Vehicle Safety Hotline tollfree at
18883274236 (TTY: 18004249153), go to http://www.nhtsa.dot.gov; or write
to:
Administrator
NHTSA
1200 New Jersey Avenue S.E.
Washington, DC 20590
You can also obtain information about motor vehicle safety from
http://www.safecar.gov.
REPORTING SAFETY DEFECTS

PAGE 4 — DCA800SSK2 60 HZ GENERATOR • OPERATION AND PARTS MANUAL — REV. #0 (09/03/09)
TABLE OF CONTENTS
DCA800SSK2
60 Hz Generator
Proposition 65 Warning ........................................... 2
Reporting Safety Defects......................................... 3
Table Of Contents.................................................... 4
Parts Ordering Procedures...................................... 5
Safety Information .............................................. 6-11
Specifications ........................................................ 12
Dimensions............................................................ 13
Installation ........................................................ 14-15
General Information............................................... 16
Major Components ................................................ 17
Generator Control Panel................................... 18-19
Engine Operating Panel.................................... 20-21
Output Terminal Panel Familiarization .............. 22-23
Load Application.................................................... 24
Generator Outputs................................................. 25
Generator Outputs/Gauge Reading....................... 26
Output Terminal Panel Connections ................. 27-28
Inspection/Setup............................................... 29-32
Generator StartUp Procedure (Manual) .......... 34-35
Generator StartUp Procedure (Auto Mode)........... 36
Generator ShutDown Procedures ......................... 37
Maintenance..................................................... 38-41
Trailer Maintenance .......................................... 42-45
Trailer Wiring Diagram ........................................... 46
Generator Wiring Diagram..................................... 47
Engine Wiring Diagram.......................................... 48
Controller Wiring Diagram ..................................... 49
Controller Wiring Diagram (Main Breaker)............. 49
Troubleshooting (Generator).................................. 50
Troubleshooting (MPEC) ....................................... 51
Troubleshooting (Engine Controller) ...................... 52
Explanation Of Code In Remarks Column............. 54
Suggested Spare Parts ......................................... 55
Component Drawings
Generator Assembly......................................... 56-59
Control Panel Assembly ................................... 60-61
Control Box Assembly ...................................... 62-65
Engine Assembly ............................................. 66-69
Radiator Assembly ........................................... 70-71
Alternator Assembly ......................................... 72-73
Thermostat Assembly....................................... 74-75
Water Pump Assembly ..................................... 76-77
Starter Assembly .............................................. 78-79
Engine Operating Panel Assembly................... 80-81
Output Terminal Assembly................................ 82-85
Battery Assembly.............................................. 86-87
Muffler Assembly .............................................. 88-89
Fuel Tank Assembly ......................................... 90-91
Enclosure Assembly #1.................................... 92-95
Enclosure Assembly #2.................................... 96-99
Enclosure Assembly #3................................ 100-103
Rubber Seals Assembly ............................... 104-105
Nameplate and Decals Assembly ................ 106-111
Terms and Conditions Of Sale — Parts............... 112

DCA800SSK2 60 HZ GENERATOR • OPERATION AND PARTS MANUAL — REV. #0 (09/03/09) — PAGE 5
PARTS ORDERING PROCEDURES
www.mqpower.com
Ordering parts has never been easier!
Choose from three easy options:
WE ACCEPT ALL MAJOR CREDIT CARDS!
When ordering parts, please supply:
RDealer Account Number
RDealer Name and Address
RShipping Address (if different than billing address)
RReturn Fax Number
RApplicable Model Number
RQuantity, Part Number and Description of Each Part
RSpecify Preferred Method of Shipment:
UPS/Fed ExDHL
NPriority OneTr u c k 
NGround
NNext Day
NSecond/Third Day
If you have an MQ Account, to obtain a Username
and Password, E-mail us at: parts@multiquip.
com.
To obtain an MQ Account, contact you
r
District Sales Manager for more information.
Order via Internet (Dealers Only):
Order parts on-line using Multiquip’s SmartEquip website!
NView Parts Diagrams
NOrder Parts
NPrint Specification Information
Note: Discounts Are Subject To Change
Goto www.multiquip.com and click on
Order Parts to log in and save!
Use the internet and qualify for a 5% Discount
on Standard orders for all orders which include
complete part numbers.*
Order via Fax (Dealers Only):
All customers are welcome to order parts via Fax.
Domestic (US) Customers dial:
1-800-6-PARTS-7 (800-672-7877)
Fax your order in and qualify for a 2% Discount
on Standard orders for all orders which include
complete part numbers.*
Order via Phone: Domestic (US) Dealers Call:
1-800-427-1244
Best Deal!
International Customers should contact
their local Multiquip Representatives for
Parts Ordering information.
Non-Dealer Customers:
Contact your local Multiquip Dealer for
parts or call 800-427-1244 for help in
locating a dealer near you.
Note: Discounts Are Subject To Change
Effective:
January 1st, 2006
NOTICE
All orders are treated as Standard Orders and will
ship the same day if received prior to 3PM PST.

PAGE 6 — DCA800SSK2 60 HZ GENERATOR • OPERATION AND PARTS MANUAL — REV. #0 (09/03/09)
SAFETY INFORMATION
Do not operate or service the equipment before reading the
entire manual. Safety precautions should be followed at all
times when operating this equipment. Failure to read and
understand the safety messages and operating instructions
could result in injury to yourself and others.
SAFETY MESSAGES
The four safety messages shown below will inform you
about potential hazards that could injure you or others.The
safety messages specifically address the level of exposure
to the operator and are preceded by one of four words:
DANGER, WARNING, CAUTION or NOTICE.
SAFETY SYMBOLS
DANGER
Indicates a hazardous situation which, if not avoided,
WILL result in DEATH or SERIOUS INJURY.
WARNING
Indicates a hazardous situation which, if not avoided,
COULD result in DEATH or SERIOUS INJURY.
CAUTION
Indicates a hazardous situation which, if not avoided,
COULD result in MINOR or MODERATE INJURY.
NOTICE
Addresses practices not related to personal injury.
Potential hazards associated with the operation of this
equipment will be referenced with hazard symbols which
may appear throughout this manual in conjunction with
safety messages.

DCA800SSK2 60 HZ GENERATOR • OPERATION AND PARTS MANUAL — REV. #0 (09/03/09) — PAGE 7
SAFETY INFORMATION
GENERAL SAFETY
CAUTION
NEVERoperate this equipment without proper protective
clothing, shatterproof glasses, respiratory protection,
hearing protection, steel-toed boots and other protective
devices required by the job or city and state regulations.
NEVERoperate this equipment when not
feeling well due to fatigue, illness or when
under medication.
NEVERoperate this equipment under the influence of
drugs or alcohol.
ALWAYScheck the equipment for loosened threads or
bolts before starting.
DO NOTuse the equipment for any purpose other than
its intended purposes or applications.
NOTICE
This equipment should only be operated by trained and
qualified personnel 18 years of age and older.
Whenever necessary, replace nameplate, operation and
safety decals when they become difficult read.
Manufacturer does not assume responsibility for any
accident due to equipment modifications. Unauthorized
equipment modification will void all warranties.
NEVERuse accessories or attachments that are not
recommended by MQ Power for this equipment. Damage
to the equipment and/or injury to user may result.
ALWAYSknow the location of the nearest
fire extinguisher.
ALWAYSknow the location of the nearest
first aid kit.
ALWAYSknow the location of the nearest
phone or keep a phone on the job site. Also, know the
phone numbers of the nearest ambulance, doctor and
fire department. This information will be invaluable in
the case of an emergency.
GENERATOR SAFETY
DANGER
NEVERoperate the equipment in an explosive
atmosphere or near combustible materials.An
explosion or fire could result causing severe
bodily harm or even death.
WARNING
NEVERdisconnect any emergency or safety devices.
These devices are intended for operator safety.
Disconnection of these devices can cause severe injury,
bodily harm or even death.Disconnection of any of these
devices will void all warranties.
CAUTION
NEVERlubricate components or attempt service on a
running machine.
NOTICE
ALWAYSensure generator is on level ground before use.
ALWAYSkeep the machine in proper running condition.
Fix damage to machine and replace any broken parts
immediately.
ALWAYSstore equipment properly when it is not being
used. Equipment should be stored in a clean, dry location
out of the reach of children and unauthorized personnel

PAGE 8 — DCA800SSK2 60 HZ GENERATOR • OPERATION AND PARTS MANUAL — REV. #0 (09/03/09)
SAFETY INFORMATION
ENGINE SAFETY
DANGER
The engine fuel exhaust gases contain poisonous carbon
monoxide. This gas is colorless and odorless, and can
cause death if inhaled.
The engine of this equipment
requires an adequate free
flow of cooling air. NEVER
operate this equipment in
any enclosed or narrow area
where free flow of the air is
restricted. If the air flow is
restricted it will cause injury to people and property and
serious damage to the equipment or engine.
WARNING
DO NOTplace hands or fingers inside engine
compartment when engine is running.
NEVERoperate the engine with heat shields or
guards removed.
Keep fingers, hands hair and clothing away
from all moving parts to prevent injury.
DO NOTremove the radiator cap while the
engine is hot. High pressure boiling water
will gush out of the radiator and severely
scald any persons in the general area of
the generator.
DO NOTremove the coolant drain plug while the engine
is hot. Hot coolant will gush out of the coolant tank and
severely scald any persons in the general area of the
generator.
DO NOTremove the engine oil drain plug while the
engine is hot. Hot oil will gush out of the oil tank and
severely scald any persons in the general area of the
generator.
CAUTION
NEVERtouch the hot exhaust manifold,
muffler or cylinder. Allow these parts to cool
before servicing equipment.
NOTICE
NEVERrun engine without an air filter or with a dirty air
filter. Severe engine damage may occur. Service air filter
frequently to prevent engine malfunction.
NEVERtamper with the factory settings
of the engine or engine governor. Damage
to the engine or equipment can result
if operating in speed ranges above the
maximum allowable.
Wet stacking is a common problem with diesel engines
which are operated for extended periods with light or
no load applied. When a diesel engine operates without
sufficient load (less than 40% of the rated output), it will
not operate at its optimum temperature. This will allow
unburned fuel to accumulate in the exhaust system,
which can foul the fuel injectors, engine valves and
exhaust system, including turbochargers, and reduce
the operating performance.
In order for a diesel engine to operate at peak efficiency,
it must be able to provide fuel and air in the proper ratio
and at a high enough engine temperature for the engine
to completely burn all of the fuel.
Wet stacking does not usually cause any permanent
damage and can be alleviated if additional load is
applied to relieve the condition. It can reduce the system
performance and increase maintenance. Applying an
increasing load over a period of time until the excess
fuel is burned off and the system capacity is reached
usually can repair the condition. This can take several
hours to burn off the accumulated unburned fuel.
State Health Safety Codes and Public Resources
Codes specify that in certain locations, spark arresters
must be used on internal combustion engines that use
hydrocarbon fuels. A spark arrester is a device designed
to prevent accidental discharge of sparks or flames
from the engine exhaust. Spark arresters are qualified
and rated by the United States Forest Service for this
purpose. In order to comply with local laws regarding
spark arresters, consult the engine distributor or the
local Health and Safety Administrator.

DCA800SSK2 60 HZ GENERATOR • OPERATION AND PARTS MANUAL — REV. #0 (09/03/09) — PAGE 9
SAFETY INFORMATION
FUEL SAFETY
DANGER
DO NOTstart the engine near spilled fuel or combustible
fluids. Diesel fuel is extremely flammable and its vapors
can cause an explosion if ignited.
ALWAYSrefuel in a well-ventilated area, away from
sparks and open flames.
ALWAYSuse extreme caution when working with
flammable liquids.
DO NOTfill the fuel tank while the engine is running
or hot.
DO NOToverfill tank, since spilled fuel could ignite if it
comes into contact with hot engine parts or sparks from
the ignition system.
Store fuel in appropriate containers, in well-ventilated
areas and away from sparks and flames.
NEVERuse fuel as a cleaning agent.
DO NOTsmoke around or near the
equipment. Fire or explosion could result
from fuel vapors or if fuel is spilled on a
hot engine.
TOWING SAFETY
CAUTION
Check with your local county or state safety
towing regulations, in addition to meeting
Department of Transportation (DOT)
SafetyTowing Regulations, before towing
your generator.
Refer to MQ Power trailer manual for additional safety
information.
In order to reduce the possibility of an accident while
transporting the generator on public roads, ALWAYS
make sure the trailer that supports the generator and
the towing vehicle are mechanically sound and in good
operating condition.
ALWAYS shutdown engine before transporting
Make sure the hitch and coupling of the towing vehicle
are rated equal to, or greater than the trailer “gross
vehicle weight rating.”
ALWAYSinspect the hitch and coupling for wear. NEVER
tow a trailer with defective hitches, couplings, chains, etc.
Check the tire air pressure on both towing vehicle and
trailer. Trailer tires should be inflated to 50 psi cold.
Also check the tire tread wear on both vehicles.
ALWAYSmake sure the trailer is equipped with a safety
chain.
ALWAYSproperly attach trailer’s safety chains to towing
vehicle.
ALWAYSmake sure the vehicle and trailer directional,
backup, brake and trailer lights are connected and
working properly.
DOT Requirements include the following:
• Connect and test electric brake operation.
• Secure portable power cables in cable tray with tie
wraps.
The maximum speed for highway towing is55 MPH unless
posted otherwise.Recommended off-road towing is not to
exceed 15 MPH or less depending on type of terrain.
Avoid sudden stops and starts.This can cause skidding,
or jack-knifing. Smooth, gradual starts and stops will
improve towing.
Avoid sharp turns to prevent rolling.
Trailer should be adjusted to a level position at all times
when towing.
Raise and lock trailer wheel stand in up position when
towing.
Placechock blocks underneath wheel to prevent rolling
while parked.
Placesupport blocks underneath the trailer’s bumper
to prevent tipping while parked.
Use the trailer’s swivel jack to adjust the trailer height to
a level position while parked.

PAGE 10 — DCA800SSK2 60 HZ GENERATOR • OPERATION AND PARTS MANUAL — REV. #0 (09/03/09)
SAFETY INFORMATION
ELECTRICAL SAFETY
DANGER
DO NOTtouch output terminals during
operation. Contact with output terminals
during operation can cause electrocution,
electrical shock or burn.
The electrical voltage required to
operate the generator can cause severe
injury or even death through physical contact with live
circuits. Turn generator and all circuit breakers OFF
before performing maintenance on the generator or
making contact with output terminals.
NEVERinsert any objects into the output
receptacles during operation. This is
extremely dangerous.The possibility exists
of electrical shock, electrocution or
death.
Backfeed to a utility system can cause
electrocution and/or property damage.
NEVER connect the generator to a
building’s electrical system without
a transfer switch or other approved
device. All installations should be
performed by a licensed electrician in accordance with
all applicable laws and electrical codes. Failure to do so
could result in electrical shock or burn, causing serious
injury or even death.
Power Cord/Cable Safety
DANGER
NEVERlet power cords or cables lay in water.
NEVER stand in waterwhile AC power from the
generator is being transferred to a load.
NEVERuse damaged or worn cables or cords when
connecting equipment to generator. Inspect for cuts in
the insulation.
NEVERgrab or touch a live power
cord or cable with wet hands. The
possibility exists of electrical shock,
electrocution or death.
Make sure power cables are securely connected to the
generator’s output receptacles. Incorrect connections
may cause electrical shock and damage to the
generator.
NOTICE
ALWAYSmake certain that proper power or extension
cord has been selected for the job. See Cable Selection
Chart in this manual.
Grounding Safety
DANGER
ALWAYSmake sure that electrical circuits are properly
grounded to a suitable earth ground (ground rod) per
the National Electrical Code (NEC) and local codes
before operating generator. Severe injury or death by
electrocution can result from operating an ungrounded
generator.
NEVERuse gas piping as an electrical ground.

DCA800SSK2 60 HZ GENERATOR • OPERATION AND PARTS MANUAL — REV. #0 (09/03/09) — PAGE 11
SAFETY INFORMATION
BATTERY SAFETY
DANGER
DO NOTdrop the battery. There is a possibility that the
battery will explode.
DO NOTexpose the battery to open flames,
sparks, cigarettes, etc.The battery contains
combustible gases and liquids. If these
gases and liquids come into contact with a
flame or spark, an explosion could occur.
WARNING
ALWAYSwear safety glasses when handling
the battery to avoid eye irritation.The battery
contains acids that can cause injury to the
eyes and skin.
Use well-insulated gloves when picking up the battery.
ALWAYSkeep the battery charged. If the battery is not
charged, combustible gas will build up.
ALWAYSrecharge the battery in a well-ventilated
environment to avoid the risk of a dangerous concentration
of combustible gasses.
If the battery liquid (dilute sulfuric acid) comes into
contact with clothing or skin, rinse skin or clothing
immediately with plenty of water.
If the battery liquid (dilute sulfuric acid) comes into
contact with eyes, rinse eyes immediately with plenty
of water and contact the nearest doctor or hospital to
seek medical attention.
CAUTION
ALWAYSdisconnect the NEGATIVE battery terminal
before performing service on the generator.
ALWAYSkeep battery cables in good working condition.
Repair or replace all worn cables.
ENVIRONMENTAL SAFETY
NOTICE
Dispose of hazardous waste properly.
Examples of potentially hazardous waste
are used motor oil, fuel and fuel filters.
DO NOTuse food or plastic containers to
dispose of hazardous waste.
DO NOTpour waste, oil or fuel directly onto the ground,
down a drain or into any water source.

PAGE 12 — DCA800SSK2 60 HZ GENERATOR • OPERATION AND PARTS MANUAL — REV. #0 (09/03/09)
SPECIFICATIONS
Generator SpecificationsTable 1.
Model DCA800SSK2 (Standard)
Type Revolving field, self ventilated,
open protected type synchronous generator
Armature Connection Star with Neutral
Phase 3
Standby Output 880 kVA (704 kW)
Prime Output 800 kVA (640 kW)
Voltage - 1 Ø 120, 127, 139, 240, 254, 277V Adjustable
Voltage - 3 Ø 208, 220, 240, 416, 440, 480V Reconnectable
Frequency 60 Hz
Speed 1800 rpm
Power Factor 0.8
Aux. AC Power Single Phase, 60 Hz
Aux. Voltage/Output 4.8 Kw (2.4 kW x 2)
Dry Weight 23,634 lbs. (10,720 kg.)
Wet Weight 25,308 lbs. (11,479 kg.)
Engine SpecificationsTable 2.
Model KOMATSU SAA6D170E3
Type 4 cycle, watercooled, direct injection, turbocharged
airtoair intercooled
No. of Cylinders 6 cylinders
Bore x Stroke 6.69in. x 6.69 in. (170 mm x 170 mm)
Displacement 1413 cu. in. (23,150 cc)
Rated Output 1008 HP/1800 RPM
Starting Electric 24 VDC
Coolant Capacity 40.4 gal. (153 liters)
Lube Oil Capacity 37.2 gal. (141 liters)
Fuel Type #2 Diesel Fuel
Fuel Tank Capacity 129.5 gal. (490 liters)
Fuel Consumption 41.3 gal. (156.5 L)/hr at full load 30.8 gal. (116.4 L)/hr at 75% load
22.6 gal. (85.9 L)/hr at 50% load 14.5 gal. (54.9 L)/hr at 25% load
Battery 12V 200Ah x 4 (24V System)

DCA800SSK2 60 HZ GENERATOR • OPERATION AND PARTS MANUAL — REV. #0 (09/03/09) — PAGE 13
DIMENSIONS
DimensionsFigure 1.
DimensionsTable 3.
Reference
Letter Dimension in. (mm) Reference Letter Dimension in. (mm)
A 43.31 in. (1,100 mm.) H 32.68 in. (830 mm.)
B 36.22 in. (920 mm.) I 39.37 in. (1000 mm.)
C 27.17 in. (690 mm.) J 29.53 in. (750 mm.)
D 43.31 in. (1,100 mm.) K 240.54 in. (6110 mm.)
E 29.53 in. (750 mm.) L 98.43 in. (2500 mm.)
F 39.37 in. (1000 mm.) M 76.77 in. (1950 mm.)
G 32.68 in. (830 mm.)

PAGE 14 — DCA800SSK2 60 HZ GENERATOR • OPERATION AND PARTS MANUAL — REV. #0 (09/03/09)
INSTALLATION
Typical Generator Grounding ApplicationFigure 2.

DCA800SSK2 60 HZ GENERATOR • OPERATION AND PARTS MANUAL — REV. #0 (09/03/09) — PAGE 15
INSTALLATION
OUTDOOR INSTALLATION
Install the generator in a area that is free of debris,
bystanders, and overhead obstructions. Make sure the
generator is on secure level ground so that it cannot slide
or shift around. Also install the generator in a manner so
that the exhaust will not be discharged in the direction of
nearby homes.
The installation site must be relatively free from moisture
and dust. All electrical equipment should be protected from
excessive moisture. Failure to do will result in deterioration
of the insulation and will result in short circuits and
grounding.
Foreign materials such as dust, sand, lint and abrasive
materials have a tendency to cause excessive wear to
engine and alternator parts.
INDOOR INSTALLATION
Exhaust gases from diesel engines are extremely
poisonous. Whenever an engine is installed indoors the
exhaust fumes must be vented to the outside. The engine
should be installed at least two feet from any outside wall.
Using an exhaust pipe which is too long or too small can
cause excessive back pressure which will cause the engine
to heat excessively and possibly burn the valves.
MOUNTING
The generator must be mounted on a solid foundation (such
as concrete) and set firmly on the foundation to isolate
vibration of the generator when it is running.The generator
must set at least 6 inches above the floor or grade level (in
accordance to NFPA 110, Chapter 54.1). DO NOT remove
the metal skids on the bottom of the generator. They are
to resist damage to the bottom of the generator and to
maintain alignment.
CAUTION
Pay close attention to ventilation when operating the
generator inside tunnels and caves.The engine exhaust
contains noxious elements. Engine exhaust must be
routed to a ventilated area.
GENERATOR GROUNDING
To guard against electrical shock and possible damage to
the equipment, it is important to provide a good EARTH
ground (Figure 2).
Article 250 (Grounding) of the National Electrical Code
(NEC) provides guide lines for proper grounding and
specifies that the cable ground shall be connected to the
grounding system of the building as close to the point of
cable entry as practical.
NEC articles 25064(b) and 25066 set the following
grounding requirements:
Use one of the following wire types to connect the1.
generator to earth ground.
Copper 10 AWG (5.3 mm2) or larger.a.
Aluminum 8 AWG (8.4 mm2) or larger.b.
When grounding the generator (Figure 2) connect the2.
ground cable between the lock washer and the nut on
the generator and tighten the nut fully. Connect the
other end of the ground cable to earth ground.
NEC article 25052(c) specifies that the earth ground rod3.
should be buried a minimum of 8 ft. into the ground.
NOTICE
When connecting the generator to any buildings
electrical system ALWAYS consult with a licensed
electrician.

PAGE 16 — DCA800SSK2 60 HZ GENERATOR • OPERATION AND PARTS MANUAL — REV. #0 (09/03/09)
GENERATOR
The MQ Power Model DCA800SSK2 is a 640 kW generator
(Figure 3) that is designed as a high quality portable
(requires a trailer for transport) power source for telecom
sites, lighting facilities, power tools, submersible pumps
and other industrial and construction machinery.
ENGINE OPERATING PANEL
The “Engine Operating Panel” is provided with the following:
Tachometer
Emergency Stop Switch
Water Temperature Gauge
Oil Pressure Gauge
Charging Ammeter Gauge
Fuel Level Gauge
Pilot Lamp
PreHeat Lamp
Engine Speed Switch
Battery Switch
Engine Alarm Lamps (6)
GENERATOR CONTROL PANEL
The “Generator Control Panel” is provided with the following:
Frequency Meter (Hz)
AC Ammeter (Amps)
AC Voltmeter (Volts)
Ammeter ChangeOver Switch
Voltmeter ChangeOver Switch
Voltage Regulator
Panel Light/Panel Light Switch
3Pole, 2500 amp Main Circuit Breaker
“Control Box” (located behind the Gen. Control Panel)
Automatic Voltage Regulator•
Current Transformer•
OverCurrent Relay•
Voltage Rectifier•
Starter Relay•
Engine Controller (Computer Controlled)•
Voltage ChangeOver Board•
OUTPUT TERMINAL PANEL
The “Output Terminal Panel” is provided with the following:
Three 240/139V output receptacles (CS6369), 50A
Three auxiliary circuit breakers, 50A
Eight output terminal lugs (3Ø power)
Battery Charger (Optional)
Water Heater (Optional)
OPEN DELTA EXCITATION SYSTEM
The DCA800SSK2 generator is equipped with the state
of the art “OpenDelta” excitation system. The open delta
system consist of an electrically independent winding wound
among stationary windings of the AC output section.
There are four connections of the open delta A, B, C and
D. During steady state loads, the power from the voltage
regulator is supplied from the parallel connections of A to
B, A to D, and C to D. These three phases of the voltage
input to the voltage regulator are then rectified and are the
excitation current for the exciter section.
When a heavy load, such as a motor starting or a short
circuit occurs, the automatic voltage regulator (AVR)
switches the configuration of the open delta to the series
connection of B to C. This has the effect of adding the
voltages of each phase to provide higher excitation to the
exciter section and thus better voltage response during the
application of heavy loads.
The connections of the AVR to the AC output windings are
for sensing only. No power is required from these windings.
The opendelta design provides virtually unlimited excitation
current, offering maximum motor starting capabilities. The
excitation does not have a “fixed ceiling” and responds
according the demands of the required load.
ENGINE
The DCA800SSK2 is powered by a 6 cylinder, water
cooled, direct injection, turbocharged airtoair KOMATSU
SAA6D170E3 Diesel Engine. This engine is designed to
meet every performance requirement for the generator.
Reference Table 2 for engine specifications.
In keeping with MQ Power’s policy of constantly improving
its products, the specifications quoted herein are subject
to change without prior notice.
ELECTRIC GOVERNOR SYSTEM
The electric governor system controls the RPMs of the engine.
When the engine demand increases or decreases, the
governor system regulates the frequency variation to ±.25%.
EXTENSION CABLES
When electric power is to be provided to various tools or
loads at some distance from the generator, extension cords
are normally used. Cables should be sized to allow for
distance in length and amperage so that the voltage drop
between the generator and point of use (load) is held to
a minimum. Use the cable selection chart (Table 6) as a
guide for selecting proper extension cable size.
GENERAL INFORMATION

DCA800SSK2 60 HZ GENERATOR • OPERATION AND PARTS MANUAL — REV. #0 (09/03/09) — PAGE 17
MAJOR COMPONENTS
Major ComponentsFigure 3.
Generator Major ComponentsTable 4.
ITEM NO. DESCRIPTION
1 Air Filter Assembly
2 Muffler Assembly
3 Fuel Tank Assembly
4 Engine Operating Panel Assembly
5 Battery Assembly
6 Output Terminal Panel Assembly
7 Generator Assembly
8 Generator Control Panel Assembly
9 Engine Control Panel Assembly

PAGE 18 — DCA800SSK2 60 HZ GENERATOR • OPERATION AND PARTS MANUAL — REV. #0 (09/03/09)
GENERATOR CONTROL PANEL
Generator Control PanelFigure 4.
The definitions below describe the controls and functions of
the DCA800SSK2 Generator Control Panel (Figure 4).
AC Voltmeter1. — Indicates the output voltage present
at the U,V, and W Output Terminal Lugs.
Pilot Lamp2. — Indicates the system is running.
Panel Light3. — Normally used in dark areas or at night
time.When activated, panel lights will illuminate.When
the generator is not in use be sure to turn the panel
light switch to the OFF position.
Frequency Meter4. — Indicates the output frequency
in hertz (Hz). Normally 60 Hz.
AC Ammeter5. — Indicates the amount of current the
load is drawing from the generator per leg selected by
the ammeter phaseselector switch.
Voltmeter ChangeOver Switch6. — This switch allows
the AC voltmeter to indicate phase to phase voltage
between any two phases of the output terminals or to
be switched off.
Panel Light Switch7. — When activated will turn on
control panel light.
Voltage Regulator Control8. — Allows ±15% manual
adjustment of the generator’s output voltage.
Ammeter ChangeOver Switch9. — This switch allows
the AC ammeter to indicate the current flowing to the load
connected to any phase of the output terminals, or to be
switched off. This switch does not effect the generator
output in any fashion, it is for current reading only.
Circuit Breaker (ON) Switch10. — Press this switch to
place the 2500 amp circuit breaker in the closed (ON)
position.
Circuit Breaker (OFF) Switch11. — Press this switch to
place the 2500 amp circuit breaker in the open (OFF)
position.
CIircuit Breaker (ON) Lamp12. — When the circuit breaker
ON switch is placed in the ON position this lamp willl be
turned ON.
CIircuit Breaker (OFF) Lamp13. — When the circuit
breaker ON switch is placed in the OFF position this
lamp will be turned ON.

DCA800SSK2 60 HZ GENERATOR • OPERATION AND PARTS MANUAL — REV. #0 (09/03/09) — PAGE 19
GENERATOR CONTROL PANEL
Auto On/Off Engine Controller (MPEC)14. — This
controller has a vertical row of status LED’s (inset), that
when lit, indicate that an engine malfunction (fault) has
been detected. When a fault has been detected the
engine controller will evaluate the fault and all major
faults will shutdown the generator. During cranking
cycle, The MPEC will attempt to crank the engine for
10 seconds before disengaging.
If the engine does not engage
(start) by the third attempt, the
engine will be shutdown by the
engine controller’s Over Crank
Protection mode. If the engine
engages at a speed (RPM’s)
that is not safe, the controller will
shutdown the engine by initializing the Over Speed
Protection mode.
Also the engine controller will shut down the engine in the
event of low oil pressure, high coolant temperature, low
coolant level, and loss of magnetic pickup.These conditions
can be observed by monitoring the LED status indicators
on the front of the controller module.
MPEC Control Switch— This switch controls the
running of the unit. If this switch is set to the OFF/RESET
position, the unit will not run.When this switch is set to the
manual position, the generator will start immediately.
If the generator is to be connected to a building’s AC
power source via a transfer switch (isolation), place the
switch in the AUTO position. In this position, should an
outage occur, the automatic transfer switch (ATS) will
start the generator automatically via the generator’s
autostart contacts connected to the ATS’s start contacts.
Please refer to your ATS installation manual for further
instructions for the correct installation of the autostart
contacts of the geerator to the ATS.
Low Oil Pressure— Indicates the engine pressure
has fallen below a safe operating level.The oil pressure
is detected using variable resistive values from the
oil pressure sending unit. This is considered a major
fault.
High Coolant Temperature— Indicates the engine
temperature has exceeded a safe operating level. The
engine temperature is detected using variable resistive
values from the temperature sending unit. This is
considered a major fault.
Overcrank Shutdown— Indicates the unit has
attempted to start a pre programmed number of timesand
has failed to start.The number of cycles and duration are
programmable. It is preset at 3 cycles with a 10second
duration. This is considered a major fault.
Overspeed Shutdown— Indicates the engine is running
at an unsafe speed. This is considered a major fault.
Engine Running— Indicates that engine is running at
a safe operating speed.
Located behind the generator control panel is the
Generator Control Box. This box contains some of the
necessary electronic components required to make the
generator function.
The Control Box is equipped with the following major
components:
OverCurrent Relay
Voltage Rectifier (AVR)
Starter Relay
Current Transformer
Voltage ChangeOver Board
Three Phase Circuit Breaker
NOTICE
Remember the overcurrent relay monitors the current
flowing from the U,V, and W Output Terminal Lugs
to the load.
In the event of a short circuit or over current condition,
it will automatically trip the 2500 amp main breaker.
To restore power to the Output Terminal Panel, press
the reset button on the overcurrent relay and place the
main circuit breaker in the closed position (ON).

PAGE 20 — DCA800SSK2 60 HZ GENERATOR • OPERATION AND PARTS MANUAL — REV. #0 (09/03/09)
ENGINE OPERATING PANEL
The definitions below describe the controls and functions
of the DCA800SSK2 Engine Operating Panel (Figure 5).
Battery Switch1. — This switch should be set to the ON
position during normal operation.When the engine has
been stop, place this switch in the OFF position. DO
NOT turn this switch during normal operation, it could
cause damage to the electrical equipment.
Engine Speed Switch2. — This switch controls the
speed of the engine (low/high).
PreHeat Lamp3. — When ECU is placed in AUX
position, preheat lamp will be ON.When preheat cycle
is completed, lamp will turn OFF.
PreHeat Button4. — Push this button when the engine
is ready for starting during cold weather operating
conditions. Keep pushing until the preheat lamp is
off.
Emergency Stop Button5. — Push this button inward to
stop the engine in the event of an emergency. DO NOT
use this button as a means of stopping the engine.
Tachometer6. — Indicates engine speed in RPM’s for 60
Hz operation. This meter should indicate 1800 RPM’s
when the rated load is applied. In addition a built in hour
meter will record the number of operational hours that
the generator has been in use.
Oil Pressure Gauge7. — During normal operation this
gauge be should read between 28 to 85 psi. (193~586
kPa).When starting the generator the oil pressure may
read a little higher, but after the engine warms up the oil
pressure should return to the correct pressure range.
Water Temperature Gauge8. — During normal
operation this gauge be should read between 167°
and 203°F (75°~95°C).
Charging Ammeter Gauge9. — Indicates the current
being supplied by the engine’s alternator which
provides current for generator’s control circuits and
battery charging system.
Fuel Gauge10. — Indicates amount of diesel fuel available.
Engine Warning Lamps11. — There are six engine
warning lamps, they are defined as follows:
Overheat Lampa. — This lamp goes ON
when the cooling water temperature rises
abnormally. If the lamp goes ON during
normal operation of the generator, the
emergency shutdown device will stop the
engine automatically.
Low Oil Pressure Lampb. — During
normal operation of the generator this
lamp should remain OFF. When the
AutoOFF/ResetManual switch is set to
the MANUAL position to start the engine,
the lamp will be lit.When the oil pressure
rises after startup the lamp will go OFF. If this lamp
is ever lit (ON) during normal operation of the
generator, the emergency shutdown device will stop
the engine automatically.
Low Fuel Level Lampc. — When this lamp
is ON, it is time to stop the engine and
add fuel. Remember to let the engine cool
before adding fuel.
Air Filter Alarmd. — When the air filter
element is clogged, this lamp goes ON
indicating the element should be
immediately cleaned or replaced.
Oil Filter Alarme. — This lamp goes ON
when the coolant level is low. If this lamp
goes ON while the engine is in operation,
the emergency shutdown device will
automatically stop the engine.
Water Level Lampf. — This lamp goes ON
when the coolant level is low. If this lamp
goes ON while the engine is in operation,
the emergency shutdown device will
automatically stop the engine.
COOLANT LEVE
L
Engine Operating PanelFigure 5.