MULTIQUIP GA-6HA How to use

The following instructions are intended to assist the
user in starting the GA-6HA AC Generator. Please read
the entire instructions before starting.
GA-6HA AC Generator
Starting Instructions
Engine Oil Check
1. To check the engine oil level, place the generator on
secure level ground with the engine stopped.
2. Remove the filler cap/dipstick from the engine oil filler
hole and wipe it clean.
3. Insert and remove the dipstick without screwing it into
the filler neck. Check the oil level shown on the
dipstick.
4. If the oil level is low (Figure 1), fill to the edge of the
oil filler hole with the recommended oil type (Table 1).
Maximum oil capacity is 1.16 quarts (1.1 liters).
edarGliOrotoM.1elbaT
erutarepmeTronosaeS liorotomfoedarG
)ssalcSMnahtrehgih(
nmutuAroremmuS,gnirpS
F°51+otF°021+ 03EAS
retniW
F°5
1+otF°04+ 03EAS
F°51+woleB03-W01EAS
Figure 1. Engine Oil Dipstick (Oil Level)
Gasoline is extremely flammable, and its
vapors can cause an explosion if ignited.
DO NOT start the engine near spilled fuel
or combustible fluids.
DO NOT fill the fuel tank while the engine is running or
hot. DO NOT overfill tank, since spilled fuel could ignite if
it comes into contact with hot engine parts or sparks from
the ignition system. Store fuel in approved containers, in
well-ventilated areas and away from sparks and flames.
Explosive Fuel Hazards
WARNINGWARNING
WARNINGWARNING
WARNING
Fuel Check
1. Close the fuel cock before filling the fuel tank.
2. Remove the fuel cap located on top of fuel tank.
3. Read thefuelgauge locatedon topofthe fueltank (Figure
2) to determine if the fuel level is low. If fuel is low,
replenish with clean unleaded fuel .
4. When refueling, be sure to use a strainer for filtration.
DO NOT top-off fuel. DO NOT fill the tank beyond
capacity. Wipe up any spilled fuel
immediately!
Figure 2. Fuel Gauge
Before Starting the Engine
1. Be sure to disconnect all electrical loads from the
generator prior to starting the engine.
2. NEVER start the engine with the main circuit breaker
in the ON position. Always place the main circuit
breaker (Figure 3) in the OFF position before starting.
Figure 4. Engine Fuel Valve Lever
Starting the Engine
1. Place the engine fuel valve lever (Figure 4) to the ON
position.
Figure 3. Main Circuit Breaker (OFF)

© COPYRIGHT 2005, MULTIQUIP INC.
Montreal, Canada • Manchester, UK
Rio De Janeiro, Brazil • Cipsa, Mexico
MULTIQUIP INC.
POST OFFICE BOX 6254 • CARSON, CA 90749
310-537-3700 • 800-421-1244 • FAX:[phone]
E-MAIL: [email protected] • WWW: multiquip.com
Figure 5. Choke Lever
5. Grasp the starter grip (Figure 7) and slowly pull it out.
The resistance becomes the hardest at a certain
position, corresponding to the compression point. Pull
the starter grip briskly and smoothly for starting.
Figure 7. Starter Grip
2. Place the choke lever (Figure 5) in the CLOSED
position if starting a cold engine.
3. Place the
choke lever (Figure 5) in the OPEN position
if starting a warm engine or the temperature is
warm.
4. Place the generator ON/OFF switch (Figure 6) in the
ON position.
Figure 6. Generator On/Off Switch
6. If the engine has started, slowly return the choke lever
(Figure 5) to the OPEN position. If the engine has not
started, repeat steps 1 through 5.
7. Before the generator is placed into operation, run the
engine for 3-5 minutes. Check for abnormal smells,
fuel leaks, and noises that would associate with loose
components.
Figure 8. Idle Control Switch
Connecting the Load
1. Place the full power switch (Figure 9) in the 120V or
240/120V position depending on application.
Figure 9. Power Switch
2. If small wattage power tools are required, connect
them to the 60 Hz output receptacles at this time.
Stopping the Engine
1. Place the main circuit breaker (Figure 3) in the OFF
position.
2. Place the idle control switch (Figure 8) in the OFF
position.
3. Let the engine run at idle with no load for 2-3 minutes.
4. To shut down the engine, place the generator ON/OFF
switch (Figure 6) in the OFF position.
5. Place the engine fuel valve lever (Figure 4) to the
"OFF" position.
6. Remove the load from the generator.
8. Place the idle control switch (Figure 8) in the ON
(up) position.
Figure 10. Main Circuit Breaker (ON)
3. Place main circuit breaker (Figure 10) in the ON
position.