Mustek Power Must 400 User manual

USER MANUAL
Power Must 400/600/800 LCD
Uninterruptible Power System

IMPORTANT SAFETY INSTRUCTIONS
SAVE THESE INSTRUCTIONS This manual
contains important instructions for models
Power Must 400/600/800 LCD that should
be followed during installation and
maintenance of the UPS and batteries.
Safety CAUTION!
This UPS utilizes voltages that may be hazardous. Do not attempt to
disassemble the unit. The unit contains no user serviceable parts.
Only factory service personnel may perform repairs.
Internal battery voltage is 1 Vdc. Sealed, lead-acid, 6 cells battery.
Connection to any other type of receptacle other than a two-pole,
three-wire grounding receptacle may result in s shock hazard as well
as violate local electrical codes.
In the event of an emergency, turn the power switch to the “off”
position and disconnect the power cord form the AC power supply to
properly disable the UPS
Do not allow any liquids or any foreign object to enter the UPS. Do
not place beverages or any other liquid-containing vessels on or near
the unit.
This unit intended for installation in a controlled environment
(temperature controlled, indoor area free of conductive contaminants).
Avoid installing the UPS in locations where there is standing or
running water, or excessive humidity.
Do not plug the UPS input into its own output.
Do not attach a power strip or surge suppressor to the UPS.
Do not attach non-computer-related items, such as medical
equipment, life-support equipment, microwave ovens, or vacuum
cleaners to UPS
To reduce the risk of overheating the UPS, do not cover the UPS’
cooling vents and avoid exposing the unit to direct sunlight or
installing the unit near heat emitting appliances such as space heaters
or furnaces.

Unplug the UPS prior to cleaning and do not use liquid or spray
detergent.
Do not dispose of battery or batteries in a fire. The battery may
explode.
Do not open or mutilate the battery or batteries. Released
electrolyte is harmful to the skin and eyes. It may be toxic.
A battery can present a risk of electrical shock and high short circuit
current. The following precautions should be observed when working
on batteries :
1) Remove watches, rings, or other metal objects from the hand.
) Use tools with insulated handles.
3) Wear rubber gloves and boots.
4) Do not lay tools or metal parts on the top of batteries.
5) Disconnect charging source prior to connecting or disconnecting
batteries terminal.
Servicing of batteries should be performed or supervised by personnel
knowledgeable of batteries and the required precautions. Keep
unauthorized personnel away from batteries.
When replacing batteries, replace with the same number of the
sealed lead-acid batteries.
This pluggable type A equipment with battery already installed by the
supplier is operator installable and may be operated by laymen.
During the installation of this equipment it should be assured that the
sum of the leakage currents of the UPS and the connected loads does
not exceed 3.5mA.
The mains socket outlet that supplies the UPS shall be installed near
the UPS and shall be easily accessible.
WARNING: This is a UPS Class C2. In residential subdivision the product may
cause harmful interference, then the users have to take additional measures.”

System Description
Front Panel—
1. LCD Back-Light
. Power “ON/OFF” Switch
Back Panel—
1. Communication Port(optional)
. Modem/Phone Line Surge Protection
3. AC Output
4. AC Input

Installation and Operation
Installing the UPS is as easy as following the steps shown. Be
aware of the Power Switch must be kept in the “ON” position,
otherwise, the UPS will be disabled and your equipment will not be
protected during a power failure.
1. Inspection
Remove the UPS from its packaging and inspect it for damage that
may have occurred during shipping. If any damage is discovered,
repack the unit and return it to the place of purchase.
2. Placement
Install the UPS unit in any protected environment that provides
adequate airflow around the unit, and is free from excessive dust,
corrosive fumes and conductive contaminants. Do not operate your
UPS in an environment where the ambient temperature or humidity is
high. On the other hand, place the UPS unit away from monitor at least
0cm to avoid interference.
3. Charging
This unit is shipped from the factory with its internal battery fully
charged. however, some energy may be lost during shipping so the
battery should be recharged before using it. Plug the unit into an
appropriate power supply and allow the UPS to charge fully by leaving
it plugged in for 8 hours.
8 hours

4. Computer Connection
Connect one computer-related device into each of the power
receptacles supplied on the back of the UPS (maximum of three
devices).
5. Modem/Phoneline Connection
Plug incoming internet line into the “In” socket at the back of the UPS.
Use one more Internet line cable and plug one end of the Internet line
cable to the “Out” socket at the back of the UPS. Plug the other end to
the modem input socket as shown.
Modem/Fax/Phone
Wall
Outlet
6. Serial Cable Connection
To allow for unattended system shutdown for your operating system,
connect the serial cable as per diagram below.

7. Turn On/Off
To turn on the UPS unit, press the power switch lightly. To turn off the
UPS unit, press the power switch again (When Switch ONThe LED
lighting.).
8. LCD Display Specification
The LED will always turns on when UPS works, including in off charging
mode and fault mode.
When LCD start to work, it will display all information for 3s
1).When in normal mode, it will display as below.
).When in AVR mode, it will display as below. And the mark will
flicker every 1second.

3).When in battery mode, it will display as below. And the mark
will flicker every 1second.
Note: If I/P-V<40Vinput voltage will display “000”
4).When in off charging mode, it will display as below.
Note: the output voltage always is displayed as “000” in off charging
mode.
5).When in fault mode, it will display as below. “FAULT” character and
the reason of fault only.
Note: the fault code will be showed in fault mode.

6).Load level definition:
Load LEVEL Load bar Indication
0%~ 5%
5%~50%
50%~75%
75%~100%
7).Battery capacity definition:
Battery LEVEL Battery bar Indication
Battery voltage≤11V
11V≤Battery voltage≤11.5V
11.5V≤Battery voltage≤12.5V
Battery voltage≥12.5V
8).When over load, the mark will flicker every 1second.
9).When battery low, the mark will flicker every 1second.

Software Installation
-- WinPower --
WinPower is a brand new UPS monitoring software, which provides
user-friendly interface to monitor and control your UPS. This unique
software provides safely auto shutdown for multi-computer systems while
power failure. With this software, users can monitor and control any UPS
on the same LAN no matter how far from the UPS
Installation procedure:
1. Go to the website:
http://www.ups-software-download.com/winpower.htm
. Choose the operation system you need and follow the instruction
described on the website to download the software.
3. When downloading all required files from the internet, enter the serial
No: 511C1-01 0-0100-478DF A to install the software.
When your computer restarts, the WinPower software will appear as a
green plug icon located in the system tray, near the clock.

Trouble Shooting
Use the table below to solve minor UPS installation or operation
problems. If any abnormal situations occur that are not listed
above,please call service people immediately.
Symptom Possible Cause Remedy
1. Missing battery. 1. Charge battery up to 8
hours.
. Battery defect. . Replace with the same type
of battery.
No LED display on
the front panel.
3.When the Input cord
isn’t electvified and
Power switch is not
pressed.
3. Press the power switch
again or elecerity the Input
cord
Alarm buzzer
beeps
continuously
when AC supply is
normal.
Overload of the UPS. Verify that the load matches
the UPS capability specified in
the specs.
1. Overload of the UPS. 1. Remove some noncritical
load.
. Battery voltage is too
low.
. Charge battery 8 hours or
more.
When power
failure, back-up
time is shorten.
3. Battery defect due to
high temperature
operation environment,
or improper operation
to battery.
3. Replace with the same type
of battery.
1. Software is not
installed well.
1. Check the setting of the
software .
Communication
lost between UPS
and computer. . Cable is not properly
connected.
. Check the RS- 3 or USB
cable is firmly connected to
COM1/COM of the
computer and confirm the
setting again.
1. Circuit breaker is
broken.
1. Reset the circuit breaker.. Mains normal but
LCD display
Battery mode. . Power cord is loose. . Reconnect the power cord
properly.

Specification
Power Must
MODEL
400 600 800
CAPACITY VA/W 400/ 40 600/360 800/480
Voltage Range 81-145VAC / 16 - 90VAC
INPUT Frequency 50Hz/60Hz
Voltage 1101 0VAC/ 03040VAC
Voltage Regulation +/- 10%(Battery Mode)
Frequency 50Hz / 60Hz
Frequency Regulation
+/-1 Hz(Battery Mode)
OUTPUT
Output Waveform Modified Sine-wave
Battery Type 1 V/4.5Ah 1 / 8W 1 V/34W
Back up Time 10 mins100W
18 mins100W
mins100W
BATTERY
Recharge Time 8 Hours to 90% after complete discharge
TRANSFER
TIME Typical -6ms typical, 10 ms max
The LCD will always turn on when UPS work,
INDICATOR LCD Display Models Including in off charging mode and fault mode
Backup Mode Sounding every 10 seconds
Battery Low Sounding every 1 second
Overload Sounding every 0.5 seconds
Battery replace Sounding every seconds
AUDIBLE
ALARM
Fault Continuous sounding
Buck/boost with
>70% SPS load
Sounding every 0.5sec. after 5min.
And fault after 30 mins
PROTECTION Full Protection Discharge,Overcharge short circuit
and Overload Protection
PHYSICAL Dimension (DxWxD)
(mm) 330* 100 * 140
WEIGHT Net Weight 4.4Kg 5.6Kg 6.1Kg
Operating
Environment 0- 40°C, 0-90 % Relative Humidity (non-condensing)
ENVIRONMENT
Noise Level Less than 40dB
INTERFACE SmartRS- 3
(optional)
Windows family,
Sun Solaris, IBM Aix, Compaq True64,
UnixWare, FreeBSD, HP-UX, Linux and MAC
USB(optional) For Windows family & Mac