MUTOH ValueCut Series User manual

V.3 2012 Nov.
0B ValueCut Series
1B User Manual

V.3 2012 Nov.
U NOTICE
Mutoh reserves the right to modify the information contained in this user
manual at any time without prior notice; un-authorized modification, copying
distribution or display is prohibited. All comments, queries or
suggestions concerning this manual please consult with your local dealer.

ValueCutUserManual
Important Information
Thank you for purchasing the ValueCut Cutting Plotter.
Before you use the cutting plotter, please make sure that you have read the
safety precautions and instructions below.
Caution
!
SAFETYPRECAUTIONS!
For safety concern, please always hold the cutter firmly from the bottom while moving
it. Do not move the cutter by clasping the depression area on both sides.
Do not place your hand close to the tool carriage to prevent your fingers from being
clamped during the operation of the cutting plotter.
Important Information
O (Correct) X (Incorrect)

ValueCutUserManual
Important Information
Hazardous moving parts keep fingers and other body parts away!

Do not shake or drop the blade holder, a blade tip can fly out.
During an operation, do not touch any of the moving parts of this machine (such as the
carriage). Also be careful to make sure that clothing and hair do not get caught.
Always connect the power cable to a grounded outlet.
Always use the accessory power cable which is provided. Do not wire the power cable
so that it becomes bent or caught between objects.
Do not connect the power cable to branching outlet to which other machines are also
connected, or use an extension cable. There is danger of overheating and of
mis-operation of the machine.
Keep the tools away from children where they can reach.
Always put the pinch rollers within the white marks.
O (CORRECT) ╳
╳╳
╳(INCORRECT)
Press down
DISABLE
Press down
Stop bar
Note: Never press the top release grip (the release grip is fully pressed when a clip
sound is heard) and pull the bottom release grip at the same time as the pictures shown
below. This will prevent you from disabling the pinch roller as the stop bar will not reach
the correct position and therefore will not be functioning.

ValueCutUserManual
Important Information
ENABLE
Pullupbottomtoreleasegrip

ValueCut User Manual
Table of Contents
T
Ta ab bl le e o of f C Co on nt te en nt ts s
Important Information
1. General Information
1.1 Introduction 1-1
1.2 Package Items 1-1
1.3 Product Features 1-2
1.4 Appearance of ValueCut
1.4.1 The Front View 1-3
1.4.2 The Back View 1-3
1.4.3 The Whole View 1-4
1.4.4 The Left-hand Side 1-4
1.4.5 The Right-hand Side 1-5
2. Installation
2.1 Precaution 2-1
2.2 Stand & Flexible Media Support System 2-2
2.3 Desktop Flexible Media Support System 2-6
2.4 Installation of Media Basket System
2.5 Cutting Pad Installation
2-8
2-11
2.6 Blade Installation 2-13
2.7 Automatic Blade Length Detection 2-15
2.8 Cable Connections 2-17
2.8.1 USB Interface 2-17
2.8.2 Driver Un-installation 2-20
2.8.3 RS-232 Interface 2-23
2.8.4 Data Transmitting 2-23
3. The Control Panel
3.1 The LCD Panel 3-1
3.2 Menu in On-line Mode 3-2
3.3 Menu in Off-line Mode 3-3
3.4 Menu Items 3-4
4. Operation
4.1 Media Loading
4.1.1 Loading the Sheet Media 4-1
4.1.2 Loading the Roll Media 4-3
4.2 Tracking Performance 4-5
4.3 Cutting Force and Offset Adjustment 4-7
4.4 How to Cut 3mm Letter 4-8
4.5 How to Make A Long Plot 4-8
4.6 When Completing the Cutting Job 4-9
4.7 ValueCut Print Driver setting 4-10
4.7.1 Option Page 4-10
4.7.2 Paper Page 4-12

ValueCut User Manual
Table of Contents
5. Accu-Aligning System
5.1 Introduction 5-1
5.2 Calibrating the System 5-2
5.2.1 Media Calibration 5-2
5.2.2 AAS Calibration 5-2
5.2.3 AAS II on ValueCut 5-3
5.2.4 Automatic Distinction of the Plot Direction 5-5
5.3 Printer Test 5-5
5.4 Contour Cutting 5-7
5.5 Tips for AAS 5-8
6. Maintenance
6.1 Cleaning the cutting Plotter 6-1
6.2 Cleaning the Grid Drum 6-2
6.3 Cleaning the Pinch Rollers 6-2
7. Trouble Shooting
7.1 Non-Operational Problems 7-1
7.2 Operational Problems 7-2
7.2.1 LCM Error Messages 7-2
7.2.2 Other operational problems 7-3
7.3 Cutting Plotter/Computer Communication Problems
7-5
7.4 Software Problems 7-6
7.5 Cutting Quality Problems 7-7
Appendix
A-1
ValueCut Specification A-1
A-2
Blade Specification A-2
A-3 Consumable and Optional Item List A-3
A-4 CorelDRAW Plug-In Instruction A-4
A-5 Illustrator Instruction A-5

ValueCut User Manual
General Information 1-1
1.1 Introduction
ValueCut series cutting plotters have been designed to produce computer-generated images
or perform contour cutting on sheets or rolls of vinyl media.
This manual covers the following models of ValueCut series cutting plotters:
‧VC-600 for media width: 50mm(1.97”) ~ 770mm(30.3”)
‧VC-1300 for media width: 50mm(1.97”) ~ 1594mm(62.7”)
‧VC-1800 for media width: 300mm(11.8”) ~ 1900mm(74.8”)
1.2 Package Items
The package of the ValueCut model contents the items listed below, please check carefully.
If you find any item missing, please consult your local dealer for further assistance.
S
St ta an nd da ar rd d I It te em m Q Qu ua an nt ti it ty y
1. Cutting Plotter 1
2. Stand Set ( for VC-1300/1800 only )(Optional for VC-600)
 2 piece of T-shape stand
 1 piece of stand beam
 18 pieces of M6 screws
 1 piece of M5 L-shape hexagon screw driver
 1 piece of Installation Guide for Stand Set
1
3. Flexible Media Support System Package
Items VC-1300/1800
Only VC-600
1 set of Roll Media Flange (2 pieces) V V
1 set of Roll Holder (2 pieces) V V
1 set of Roll Holder Guide Bushes (4 pieces)
V V
1 set of Roll Holder Support (2 pieces) V V
1 piece of M6 L-shape hexagon screw driver
V V
1 piece of Installation Guide for Roll Holder V
1 piece of M5 L-shape hexagon screw driver
V
1 set of Desktop Support Brackets (2 pieces)
V
4 pieces of Plastic Foot V
4 pieces of M4 screws V
12 pieces of M6 screws V
1 piece of M4 L-shape hexagon screw driver
V
1
1. General Information

ValueCut User Manual
General Information 1-2
4. Accessories
 1 piece of User’s Compact Disk
 1 piece of data cable (RS-232C)
 1 piece of data cable (USB cable)
 1 set of Blade Holder Assembly (Installed in tool carriage of the cutting
plotter)
 1 piece of Blade (45°with Red Cap/ Installed in Blade Holder)
 1 piece of Safe Blade
 1 piece of Cutting Pad for Vinyl cutting
 1 piece of Tweezers
 1 Oily ball-point pen
1
1.3 Product Features
The following are the main features of the ValueCut series cutting plotters:
‧Tri-port connectivity provides you with greater flexibility
‧Up to 600-gram cutting force
‧Up to 60-inch/per second cutting speed
‧Guaranty 10-meter tracking
‧User friendly, multi-language control panel
‧Ingenious media basket (optional item)
‧Enhanced Accu-Aligning System for automatic contour cutting

ValueCut User Manual
General Information 1-3
1.4 Appearance of ValueCut
1.4.1 The Front View (Figure 1-1)
1.4.2 The Back View (Figure 1-2)
Pinch Rollers –
hold the media during
cutting.
Lever –
raises or lowers the
pinch rollers.
Figure 1-2
Control panel – consists of 14
control keys and 1 LED and 1 LCM
showing messages and menus.
Cutting Pad – provides the
protection of blade when the blade is
cutting.
Tool Carriage – performs the
cutting with the installed blade
and pen with AAS module.
Alignment Rulers –
media can be aligned
with the clear guide line
marks.
Grid Drums – move
the media back and
forth during operation.
Slicer Groove –
slice off the extra
media easily along
this groove.
Platen –
provides the
surface for holding and
supp
orting media while
performing cutting.
Figure 1-1