MYTORQ MYCS-ID120 User manual

OPERATION MANUAL FOR CHARGE STATION
 MYCS-ID120
(In: AC 100~240V Out: 21V)
ANLIDAR INDUSTRIAL CO., LTD.
http://www.anlidar.com
Y2F109-2E-001


1
Symbols
Read manual Caution Indoor use only No humidity
No fire No disassemble No disposal CE certification CETLUS
Certification
Caution
Please read all instructions carefully before operate the rechargeable battery and charger. Also
please follow all the instructions and pay attention to all the warring.
Important Notification
1. Please operate under the correct voltage to the charger in according with the operation
manual.
2. When charging the battery, please make sure the grounding and safety components are
properly attached before operate.
3. The charger should store in clean and dry area. Do not place heave stuff on the charger.
Please do not charge the battery when the temperature is above 33℃.
4. Please do not place the charger in the poorly ventilated place, nor expose the charger in
the dust or metal crumb.
5. Do not expose the charger directly under sun, high temperature, high humidity and
highly explosive gas
6. Do not place charger on high shelf. The charger should be placed on the leveled, firmed
spot that prevent children from reaching.
7. Do not abuse the cord. Never use the cord to carrying, pulling or unplugging the charger.
Keep cord away from heat, oil, sharp edges or moving parts. Damaged or entangled cords increase
the risk of electric shock.
8. Please read all instructions carefully before operate the charger. Failure to follow all
instructions listed below may result in electric shock fire and/or serious injure.
9. It is forbidden to use different brand of battery other then Kilews on the charger. To disassemble
and modify the charge are also not allowed.
Grounding Instruction
The charger needs to be grounded all the time in case of electrical shock. The grounding wire must be
connected firmly with power supply equipment for effective grounding result. The leading wire with
yellow-green color is a grounding wire. Never attempt to connect this yellow-green color wire on
electrified connector


2
Caution
1. Please match the correct Lithium-ion rechargeable battery for this charger, which is only
manufacture by Kilews. Do not apply different type or brand of battery on this charger,
otherwise may cause error or danger
2. Please match the charger with the battery models SKC-LB1820/SKC-LB1840.
The use of other than genuine Anlidar replacement parts or battery may result in decreased tool
performance and increased maintenance,and may invalidate all warranties.
3. Keep children, and bystanders away while charging the battery, in case of danger.
4. Please do not plug in the charger when the plug or users’ hand is wet.
5. To disassemble or modify the charger’s plug may cause danger or dysfunction.
6. This charger only applies to the rechargeable battery of Kilews. Please do not apply the charger to
other different brand of battery or for other propose.
7. Please do not attempt to disassemble or modify the charger and the rechargeable battery.
Operation Instruction
1. Please check the cord to see if there any damage before plug in the charger. Hold the plug of power
cord while plugging in or unplug the charger.
2. Do not place chargers near oil, chemical materials or heated objects, also please be alert not to
scratch the power cord by sharp object.
3. When the charger is not in use, please unplug the power and store in dry safe place where it is not
reachable by children.
4. Charger and battery assemble.
Assemble
(1) Match the battery to the (2)The direction of the battery (3)Inserting steps finished, the
charger’s slide track when insert, push all the way charger will identify the battery
slide in straightly. down until click sound ID, when ID are matched, there
will be a short beep sound
Decomposition
(1)Push up and hold the (2)The direction of battery (3)Removing steps finished
latch switch when removing
5. Please locate the charger close socket.


3
6. LCD Screen and LED Light Display Description
(1) When the charger plug in the power, it starts automatically. (The following lists are
charger start sequence.)
1. Light Display shows continuous green light
2. One long beep sounds
3. Fan start and then stop
(2) Red light flash => means the battery is charging.
(3) Long yellow light and flash red light=>means the battery is charged 80% and continuous
charging.
(4) Red and green lights both light up at the same time=>means the battery is fully charged 100% and
one long beep sound for 3s.
(5) Red and green lights both are blinking=>with continuous short beep sounds means there are errors
when charging the battery. Check for the battery if the battery insert correctly. If the charger
continues shows error, please change another batter to see if the error was caused by battery or
the charger. This charger only applies to the rechargeable battery of Kilews. Please do not apply
the charger to other different brand of battery.
(6) Battery status: Press (B) button for 5 seconds to switch the screen to “Battery Charge Status
Display”
Counter status
Chinese Mode Display
English Mode Display
Screen Display Description
LINE 1
Total charaged times
LINE 2
Total charaged hours
LINE 3
Total charaged minutes
Light Display
（1）
（2）
（3）
（4）
（5）
（6）
（7）
Light Display


4
(7) Language Select Button : Press (L) for 5 seconds to switch the screen to
“Language Select Menu Display”
Language Select Description
Contents
Chinese Mode Display
English Mode Display
Press (L) button for 5 seconds to
switch display from main screen
to “Language Select Menu
Display”
Press (L) button for 5 seconds to
switch display from main screen
to “Language Select Menu
Display”
There have two language for
selection:
1.EN = B Press button (B) to
select English
2.中文= L Press button (L) to
select Chinese
(*) is the current selected
language
There have two language for
selection:
1.EN = B Press button (B) to
select English
2.中文= L Press button (L) to
select Chinese
(*) is the current selected
language
Press button (B) for 5 seconds to
select English language, when
setting is completed the status
line will display :
“Set Completed!”
Press button (L) for 5 seconds to
select Chinese language, when
setting is completed the status
line will display :
“參數設定完成”
Release button (B) for 5 seconds,
System will return to main screen
and switch to English mode
display.
Release button (L) for 5 seconds,
System will return to main screen
and switch to Chinese mode
display.
MYCS-ID120 charger stand
1PCS
operation manual
1PCS
certification
1PCS


5
Other status
Chinese Mode Display
English Mode Display
LCD Display Description
LINE 1
Battery Type and ID Check status
LINE 2
Current Charging Time
LINE 3
Battery Temperature and Level
LINE 4
Charging status
Charger Information
and Buzzer Status
Description
Charger Status
Buzzer Status
BATT. ID Correct
Beep(1 sec)
Normal
"B.VOLT.FULL"
Beep(3 sec)
Normal
"BATT. FAIL "
Beep(1 sec)Continue
Abnormal
"B.TEMP. HIGH "
Beep(1 sec)Continue
Abnormal
"B.TEMP. OVER "
Beep(1 sec)Continue
Abnormal
"C.TEMP. LOW "
Beep(1 sec)Continue
Abnormal
"C.TEMP. HIGH "
Beep(1 sec)Continue
Abnormal
"BATT.ID ERROR"
Beep(1 sec)Continue
Abnormal
"BATT. OK"
-
"Ready to use ."
-
"Pre-Charge...."
-


6
Aution: Protection Functions
1. Over charged protection 2. Current protection
3. Shortage protection( fuse installation) 4. Battery reverse current protection
5. Built-in ID recognition feature protection 6. Temperature protection
(1) When the battery temperature is between 0-10℃, the charger will use low current to
pre-charge the battery until the battery temperature higher then 10℃ , then the charger switch back to
normal charging mode. When the battery temperature is below 0℃, the charger will stop charging
the battery until the battery temperature is higher then 0℃.
(2) When the battery temperature is above 45℃, the charger will automatically change to low
current to charge the battery. When the battery temperature is exceed 50℃, the charger will stop
charging the battery and make warring beep sound until the battery temperature drop down back to
40℃ , then the charger switches back to normal charging mode.
(3)When the charger temperature rises to 75℃, the charger will trigger protection mechanism to stop
charging the battery and until the charger temperature drop down back to 65℃ , then the charger
switches back to normal charging mode.
7.When the charger detects the battery temperature is lower 0℃ or about 50℃, then the charging process
will be stopped. Automatically rechargeable
8.Low power protection: when the battery voltage is lower than 15V, the charger will automatically
change to low current to pre-charge the battery and until the battery voltage is reach to 15V, then the
charger switches back to fast charging mode.
Specifications
Model type
Automatic Cordless Screwdriver Battery Charge Station
MYCS-ID120
Charge Station
Input voltage (AC)
100V – 240V/0.5A~1.2A
Output
voltage(DC)
21VDC
Output current
4.5A
3.0A
Charge time
(SKC-LB1840)
About 35 min charge to 80% and 45
min to fully charged
(SKC-LB1820)
About 25 min charge to 80% and 30 min
to fully charged
Battery capacity
(3900 mA/hr)
(1950mA/hr)
Battery type
Lithium-ion rechargeable battery
Battery ID
configuration
Battery capacity indicator to show the battery current capacity
Battery ID identifier to match the Kilews’ battery before charging.
size
W × L × H 160mm×170mm×80mm
Weight
1.1Kg
Caution
SAVE THESE INSTRUCTIONS
DO NOT DESTROY

MYTORQINDUSTRIALCO..LTD.
CUSTOMER
ITEM NO:
TITLE:
DWG NAME
DWG NO:
MATERIAL
DES. BY
CHKD.BY
APPD.BY
SHRINK
DATE
DATE
DATE
PRODUCTION NO.
THIRD ANGLE PROJECTION.
UNITSCALESHT NO.
OF SHTS.
零件
編號排插圖示排插
位置
3-2
9-1
13-1
3-1
14-1
3-2
13-1
14-1
9
17
11
1-1
7
8
4
3
2
3-1
9-1
1-116
1313-1
1414-1
18
12
15
15
55
10
6
1-2
MODELNO:
MYCS-ID120



