MYTORQ MYBT-NR2560 Series User manual

Automatic Industrial Cordless Brushless
Power Torque Screwdrivers Series
OPERATION AND MAINTENANCE MANUAL
ANLIDAR INDUSTRIAL CO., LTD.
http://www.anlidar.com
Y2F137A-1E-001
MYBT-NR2560-Series
MYBT-NR1230-Series
MYBT-NR0612-Series
MYBT-NR2560
MYBT-NR1545
MYBT-NR1230
MYBT-NR0515F
MYBT-NR0308F
MYBT-NR0815
MYBT-NR0612
MYBT-NR2507
MYBT-NR0205F
Rechargeable -TYPE Automatic Brushless Series

1
Before you use the Cordless Screwdriver for the first time, it is
essential to read and understand the manual completely (including the
spare parts view). The term “Cordless Screwdriver” in all of the
warning listed below refers to your main operated appliance.
Icon Instructions
1. 2. 3. 4.
5. 6. 7. 8. 9.
1.Read instruction manual.
6. Do not operate in an explosive atmosphere.
2. Observe caution and safety notes.
7. Do not disassemble.
3. Recyclable.
8. Forbid throwing.
4. For indoor use only.
9. CE Certificate.
5. Do not expose to wet or rain conditions.
Accessories
Item
Quantity
Unit
Suspension Hook Ring Group
1
PCS
Adjusting Wrench
1
PCS
Manual
1
PCS
Guarantee Card
1
PCS
Torque rings ass’y
1
Package
Waist hook
1
PCS
Screw M3*0.5P*10LT
1
PCS

2
Warning
Read all instructions and make sure the appearance of the device has no damage before you use it.
Failure to follow all instructions listed below may result in electric shock fire and/or serious injury.
1. Keep the working area nice and clean.
1.1Mess and dark areas may cause of accidents.
1.2Keep the device away from rain or moisture to decrease the risk of electric shock or short- circuiting
occurred.
2. Be alert to workplace safety
2.1 Use the device under a well lit and clean environment.
2.2 Keep children and other people away unless the person has been assigned for the task to avoid the
danger of injury.
2.3 Do not play around while the tool is being used to avoid the danger of distractions.
2.4 Do not work with the device in potentially explosive environments in which there are inflammable
liquids, gases or dusts. Electrical power tools create sparks, which can ignite dusts or fumes.
2.5 Do not use the device if you are tired or under the influence of drugs, alcohol or medication.
3. When the devices are not being used, store them in a safe palce.
4. Use a suitable device for the job will be safer at work and have a better result.
5. Always use a screwdriver that is intended for the task you are undertaking. Do not overload or use it
improperly such as drilling or tapping.
6. Dress properly. Do not wear loose clothing or jewels while operating the tool to avoid the danger of
trapping.
7. By using the device correctly, make sure to hold it firmly with two hands in place before starting the
trigger.
8. When using the electrical power tool, take into account the auxiliary handle or waist hook is
advantage of working conditions. On the contrary, the purposes of the waist hook or driver hook is
convenient to put the device away and easier to keep it out of reach of children.
9. Look after either the device or the battery carefully and have any damaged parts repaired by an
authorized or qualified shop. Always keep the tool nice and clean; pay attention on the machine
grease which might ruin the tool.
10. Disconnect the plug from the power source after the charger has been used.
11. Take apart the battery from the device when it is not being used.
12. Use only the accessories that are detailed in the operating instructions. The use of others which are
not recommended in the operating instructions may affect the functioning of the device. It could lead
to an increased risk of personal injury as well.
13. Remain alert at all times and watch what you are doing during proceeding. Before operation, always
check every part is in good condition and move freely in order to function properly.
14. This device only applies for metal screw bits designated with their dimensions and their shape. Do
not recommend to countersink or force of loading on any material such as plastic and wooden.
15. The device does not apply for elastic or tensile load with washer on.
16. To prevent parts in gearbox from damage, replace the grease at least once for every year.
17. It is necessary for the operators to read and follow up all the operating instructions in this manual.
MYTORQ is not responsible for any personal injury that might cause of disobeying the safety advices.
18. Use a safety device:
19. Wear protective earmuffs to reduce personal injury.
Noise:
The typical A-weighted noise level .
.Sound pressure level(LpA): 84.8 dB(A)
.Sound power level(LwA): 95.38 dB(A)
Vibration:
The vibration total value .
.Vibration emission value ah (m/s²): 6.21 m/s2
.Uncertainty K (m/s²): 1.5 m/s2

3
Forward / Reverse
Function of cordless protection
▉
Over electric current protection
▉
Prevent from low power
▉
Thermal Protector
▉
Stall protection
▉
Slow rotation protection
▉
Reverse control protection
▉
Battery Identification
▉
Sleeping mode
Warning
Do not attempt to repair or disassemble this cordless screwdriver, the warranty
will be considered void.
1. This rechargeable screwdriver maintenance Make sure to remove the battery pack before
maintaining or repairing the device by a qualified technician.
2. Do not attempt to disassemble or reassemble the device at will which may result in poor
performance or danger of injury, the warranty applies only to initial package.
3. Do not repair the device with other than genuine MYTORQ replacement parts may result in
poor performance or danger of injury, the warranty will be considered void.
4. The temperature between 0∘C ~ 35∘C would be an ideal condition of carrying out the tasks
on the device.
Operating instructions
1. Charge the battery in the charging station before first use to make sure operates at its highest
capacity. To ensure operators against injuries, release the Forward/Reverse lever as arrow
showing below into a center position to have trigger locked before start or disassemble the
device.

4
Battery
Release Button
2.1 Below illustration is showing the process of correct install & disassemble the rechargeable
battery. The beep sound comes along with a flash while the screwdriver is supplied genuine
battery installation. It could be operated once the battery has been identified.
2.2 Too slow to install the battery may cause error identification so the beep sound and flash would
be continuing. In order to function properly, re-assembling it as below process again.
3. 90° Attached Turn forward a little bit to adjust the attached angle,
angle adjustment then turn reversed to lock it.
Insert Battery Steps
((1)Insert the rechargeable battery into the device follow by the arrow as showing.
(2)Assembled completely.
Remove Battery Steps
(1)Press the release button and (2)Follow the arrow direction. (3)Removed completely.
take it out of the device
Battery
Release Button

5
Function / Operating Introduction
Function Name Table
No.
Description
No.
Description
(1)
Trigger Switch
(6)
Indication light
(2)
Forward/Reverse Lever
(7)
Torque wrench
(3)
LED Light
(8)
Speed adjustment
(4)
Torque Ring
(9)
Wrist strap hole
(5)
S waist hook
(10)
Suspension Ring Accessary
(7)
(3)
(1)
(10)
(2)
(8)
(5)
(4)
(6)
(9)

6
Manual / Function
1. Full auto shut-off screwdriver
It stops automatically when the screw has been tightened up and reached the set-up torque level.
The device will not cause damage of task since no continue running after screws are tightened.
(1) Trigger switch
The LED lights on when the trigger switch has been pressed about one-third down, and then the
screwdriver starts functioning when the switch trigger has been pressed half way down; on the
contrary, it stops when the screw has been tightened up or the trigger has been released.
(2) Forward / Reverse switch
When the switch turn to the right as arrow indicates, the screwdriver will be clock-wise
screwing to tighten things up; Vice versa, left switch means to release the screw. As the diagram
showing, always set the switch to neutral position when the screwdriver is not being used.
(3) LED light
While press the trigger, the LED lights up automatically to assist the job to be done; on the
contrary, it will be off once the trigger has been released.
(4) Torque ring
The purpose of the color ring is to have the torque level visible; there are 3 different types in
total, follow the diagram below for installation/removal.
Insert the sleeve
Forward (screw)
Reverse (unscrew)
Removal
Dismantle

7
(5) Waist hook
The waist hook allows users to carry the device easily by attaching it to their work belt.
(6) Functional light and the status indicator
Whenever the remaining power in the rechargeable battery is fewer than 20%, the tool is still
alive but with red flash lights on. Once the remaining power is towards 10% or even fewer it
may result in poor performance with the continuing red lights on.
Functional indicator
Determine the beep sound
OK screwing with preset
torque
NG screwing
Indicator light Green on~ off Red on~ off
Beep sound warning 1 short beep 1 long beep
Indicator of low battery
Power reserve <20%(17.5) Power reserve < 10%(17V)
Indicator light Blinking Red Red light on ( low power )
Beep sound warning Continuing Beeping 2 short 1 long beep
Screwdriver functioning Able to function Unable to function
(7) Torque adjustable
The torque is able to be changed by following steps
1) Remove the battery from the device or set the rotation switch to neutral
position to prevent the tool from starting up unintentionally.
2) Open up the torque safety cover cap; follow the illustration on the right
which inserting the torque wrench from the bit sleeve to turn the nut
over in a central position, the user may check the nut lock from side
uncovered window.
3) Having the torque changed by inserting the torque wrench into the nut
lock to adjust the torque range.
4) Adjusting the torque in two directions (-) for less torque (+) for more
torque.
5) Torque adjustment wrench showed in a diagram 2: when torque
rotation adjustment wrench turns to the (+) sign means that the
Torque adjustment ring will move up to the (+) sign and increase the
torque force until reached the maximum torque scale. When the
Rotation torque adjust wrench turns to the (-) means that the torque
adjustment ring will move down to the (-) sign and decrease the torque
force until reached to the minimum torque scale.
Adjust toward [+]
to increse torque。

8
Notice: Use the junction of waring spring and spring fixing plate as a reference point when adjusting
torque. To avoid jamming and abnormal conditions, please do not exceed the stop line of the high
and low torque when adjustment shown in diagram 3.
(8) Hi/Lo Switch
When the rotating speed needs to be changed, set up the switch to Hi for the fastest rotation, and set
up the switch to Lo for slowest rotation. It's possible that the uncompleted shut-off occurs when the
switch is setup to Lo and the presetting torque is more than 50% of torque range. Please refer to the
following table.
(9) Hole for wrist band
Enable to install the wrist band which is more convenient and safer for users.
Lo Switch Shut-off
OK (N.m)
NG(N.m)
MYBT-NR1545
25~30↓
30↑
MYBT-NR1545
15~22.5↓
22.5↑
MYBT-NR1230
12~15↓
15↑
MYBT-NR0515F
5~7.5↓
7.5↑
MYBT-NR0308F
3~4 ↓
4↑
MYBT-NR0815
apply to scale 8 only
8↑
MYBT-NR0612
6↓
6↑
MYBT-NR2507
2.5~3.5 ↓
3.5↑
MYBT-NR0205F
2~2.5 ↓
2.5↑
(A)
(B)
the stop line of
the low torque
(C)
the stop line of
the high torque

9
(10) Suspension Ring Accessary
Use for hanging tool apply to the application, assembly follow below steps:
(1) (2) (3) (4)
(1). Take both up and down side cover of suspension ring.
(2). Lock both screws
(3). Close the locking ring
(4). Completed
Other Cautions
1. The best condition of using the tool is under 8 hours a day, do not over loaded.
according to operating frequency and torque loaded, we suggest adding lubricating oils in clutch
per 3-6 months, and kindly contact with distributor when product's maintenance .
2. Do not attempt to repair or disassemble this cordless screwdriver without authorization. Always
have the device serviced by assigned factory or qualified person in order to have the warranty
effective continually.
3. ANLIDAR is not responsible for any poor performance or damage caused by customers own
modification of the tool.
4. It is necessary for the management to have individual operators read and follow up all
instructions in this manual. Do not attempt to repair or disassemble this cordless screwdriver
themselves.
5. Chemicals, Acetone, Benzene, Alcohol, Thinner, Ketone, trichloroethylene, etc shall not be in
contact with the surface of the screwdriver in order to prevent chemical damage.
6. Please follow instruction carefully and do not drop or shock the screwdriver.
7. This product allows you to adjust freely ( - ) and ( + ) to decrease and increase torque. Different
models will deliver different level of torque, when the torque is adjusted to the limit the switch
will not be able to turn, please do not force it or it will be damaged. High frequency of using this
power tool might cause overheating, please have the tool to be cool down properly.
8. Not allow to turn the Hi/Lo switch during operation in order to cause system malt-function.

10
9. The device will not be able to function again once the OK/NG indicator/signal is not turn off
yet.
10. When adjusting the torque, for safety purpose should stop the screwdriver completely and set
the switch to neutral position. It could prevent the user from turning the tool on accidentally.
11. During operation, the switch has been changed accidentally that the device will enable its
self-protecting mode which is power off. Re-start the tool when this happen.
12. Each operational torque setting, using time and frequency may result in different level of wear
and tear, at higher torque setting and use extensively could accelerate the wearing down of tool.
After one month, the torque is getting reduce gradually at the rate of 2~3% or 3~5 %( max
torque). The longer use of the device, torque reduction will become stable and the users could
measure the torque by a tester on a regular time schedule to check if the torque power still meets
the criteria.
13. MYBT-NR2560/1545/1230 must be measured by the KILEWS torque meter KTM-1000.
MYBT-NR05150F/0612/0815 must be measured by the KILEWS torque meter KTM-250.
MYBT-NR0308F/2507/0250F must be measured by the KILEWS torque meter KTM-150.
14. ANLIDAR cordless screwdriver torque output is generated by clutch machnisam, and it is
applicable to ISO 6789.
Description of Battery and Charger
1. Choice the suitable battery for your application,SKC-LB1840 for NR2560/1545 and
2. SKC-LB1820C for NR1230/0515F/0308F and SKC-LB1820B for NR0815/0612/2507/0205F is
recommended,Please contact to your local agents for more informat
3. The use of other than genuine ANLIDAR batteries or screwdrivers can’t be active due to the
build-in protection system enforce no charging.
4. Use MYCS-ID120/MYCS-ID80 charge station for NR2560/15455 and MYCS-ID80-D charge
station for NR1230/0515F/0308F/0815/0612/2507/0205F is recommended.
Slow speed
(rpm)
operation
frequency
Slow speed
(rpm)
operation
frequency
Slow speed
(rpm)
operation
frequency
900
1.0 ON 3.0 OFF
600
1.0 ON 3.0 OFF
300
2.0 ON 5.0 OFF
850
1.0 ON 3.0 OFF
550
2.0 ON 5.0 OFF
250
2.0 ON 5.0 OFF
800
1.0 ON 3.0 OFF
500
2.0 ON 5.0 OFF
200
2.0 ON 5.0 OFF
750
1.0 ON 3.0 OFF
450
2.0 ON 5.0 OFF
150
2.0 ON 5.0 OFF
700
1.0 ON 3.0 OFF
400
2.0 ON 5.0 OFF
100
2.0 ON 5.0 OFF
650
1.0 ON 3.0 OFF
350
2.0 ON 5.0 OFF
Slow speed Duty Cycle Conversion (for reference)
Based on 1000 rpm, 1 second ON/3 seconds OFF. For example, the duty cycle for 350rpm,
1000-350=650，650/1000%=65%
ON= 1*1.65= 1.65，OFF =3*1.65 =4.95 (rounded value) =2 seconds ON / 5 seconds OFF
This tool is intended for a duty cycle of 2.0 sec on, 5.0 sec off.

11
WARNING Read all safety warnings and all instructions. Failure to follow the
warnings and instructions may result in electric shock, fire and/or serious injury.
Save all warnings and instructions for future reference.
1) Work area safety
a) Keep work area clean and well lit . Cluttered or dark areas invite accidents.
b) Do not operate power tools in explosive atmospheres, such as in the presence of
flammable liquids, gases or dust.
Power tools create sparks which may ignite the dust or fumes.
c) Keep children and bystanders away while operating a power tool.
Distractions can cause you to lose control.
2) Electrical safety
a) Power tool plugs must match the outlet. Never modify the plug in any way. Do not
use any adapter plugs with earthed (grounded) power tools.
Unmodified plugs and matching outlets will reduce risk of electric shock.
b) Avoid body contact with earthed or grounded surfaces, such as pipes,
radiators, ranges and refrigerators. There is an increased risk of electric shock if your body is
earthed or grounded.
c) Do not expose power tools to rain or wet conditions. Water entering a power tool will
increase the risk of electric shock.
d) Do not abuse the cord. Never use the cord for carrying, pulling or
unplugging the power tool. Keep cord away from heat, oil, sharp edges or moving
parts.
Damaged or entangled cords increase the risk of electric shock.
e) When operating a power tool outdoors, use an extension cord suitable for outdoor
use.
Use of a cord suitable for outdoor use reduces the risk of electric shock.
f) If operating a power tool in a damp location is unavoidable, use a residual current
device (RCD) protected supply.
Use of an RCD reduces the risk of
electric shock.

12
3) Personal safety
a) Stay alert, watch what you are doing and use common sense when
operating a power tool. Do not use a power tool while you are tired or under the
influence of drugs, alcohol or medication.
A moment of inattention while
operating power tools may result in serious personal injury.
b) Use personal protective equipment. Always wear eye protection. Protective equipment
such as dust mask, non-skid safety shoes, hard hat, or hearing
protection used for appropriate conditions will reduce personal injuries.
c) Prevent unintentional starting. Ensure the switch is in the off-position
before connecting to power source and/or battery pack, picking up or
carrying the tool.
Carrying power tools with your finger on the switch or energizing power tools that have the switch
on invites accidents.
d) Remove any adjusting key or wrench before turning the power tool on. A wrench or a
key left attached to a rotating part of the power tool may result in
personal injury.
e)
Do not overreach. Keep proper footing and balance at all times. This
enables better control of the power tool in unexpected situations.
f) Dress properly. Do not wear loose clothing or jewellery. Keep your hair, clothing
and gloves away from moving parts.
Loose clothes, jewellery or long hair can be caught in
moving parts.
g) If devices are provided for the connection of dust extraction and collection
facilities, ensure these are connected and properly used.
Use of dust collection can reduce
dust-related hazards.
4) Power tool use and care
a) Do not force the power tool. Use the correct power tool for your application. The
correct power tool will do the job better and safer at the rate for which it was designed.

13
b) Do not use the power tool if the switch does not turn it on and off. Any power tool that
cannot be controlled with the switch is dangerous and must be repaired.
c) Disconnect the plug from the power source and/or the battery pack from
the power tool before making any adjustments, changing accessories, or
storing power tools. Such preventive safety measures reduce the risk of starting the power tool
accidentally.
d) Store idle power tools out of the reach of children and do not allow persons
unfamiliar with the power tool or these instructions to operate the power tool.
Power
tools are dangerous in the hands of untrained users.
e) Maintain power tools. Check for misalignment or binding of moving parts,
breakage of parts and any other condition that may affect the power tool’s
operation. If damaged, have the power tool repaired before use. Many
accidents are caused by poorly maintained power tools.
f) Keep cutting tools sharp and clean. Properly maintained cutting tools with
sharp cutting edges are less likely to bind and are easier to control.
g) Use the power tool, accessories and tool bits etc. in accordance with these
instructions, taking into account the working conditions and the work to be
performed.
Use of the power tool for operations different from those intended could result in a
hazardous situation.
5) Battery tool use and care
a) Recharge only with the charger specified by the manufacturer . A charger
that is suitable for one type of battery pack may create a risk of fire when used with
another battery pack.
b) Use power tools only with specifically designated battery packs . Use of any other
battery packs may create a risk of injury and fire.
c) When battery pack is not in use, keep it away from other metal objects, like paper
clips, coins, keys, nails, screws or other small metal objects, that can make a
connection from one terminal to another
. Shorting the battery terminals together may cause
burns or a fire.

14
d) Under abusive conditions, liquid may be ejected from the battery; avoid contact. If
contact accidentally occurs, flush with water. If liquid contacts eyes, additionally seek
medical help
. Liquid ejected from the battery may cause irritation or burns.
6) Service
a) Have your power tool serviced by a qualified repair person using only
identical replacement parts . This will ensure that the safety of the power tool is maintained.
WARNING Read all safety warnings and all instructions. Failure to follow the
warnings and instructions may result in electric shock, fire and/or serious injury.
Save all warnings and instructions for future reference.
.Sound power level & Vibration :
. Weighted surface sound pressure level LpfA according to EN ISO 3744: 81.9 dBA
. Uncertainty KpA: 0.566 dBA
. A-weighed sound power level LWA according to 8.6 of EN ISO 3744 : 92.9 dBA
. Uncertainty KWA: 0.566 dBA
. Weighted emission sound pressure level LpCpeak according to EN ISO 11203: 97.6dBA
. Uncertainty KpCpeak:  .....................................  0.565 dBA
. Recommendation for the operator to wear hearing protection.
. Vibration total value ahaccording to EN ISO 5349-1 and EN ISO 5349-2: 1.0683m/s2
. Uncertainty m/s2: 0.566 m/s2
. “Vibration total value may also be used in a preliminary assessment of
exposure.”
. “Warning - vibration emission during actual use of the power tool can differ from
the declared total value depending on the ways in which the tool is used.”
. “Warning - the need to identify safety measures to protect the operator that are based on
an estimation of exposure in the actual conditions of use.”

15
Specifications
Bits Code ~ W: square B: Hex 6.35mm
CAUTION
SAVE THE INSTRUCTIONS
DO NOT DESTROY
MODEL
(MYBT-)
L600-Series L300-Series L150-Series
NR2560 NR1545 NR1230 NR0515F NR0308F NR0815 NR0612 NR2507 NR0205F
INPUT
VOLTAGE(DC)
DC 18V
TORQUE
(N.m)
hard
joints
25-60 15-45 12-30 5-15 3-8 8-15 6-12 2.5-7 2-5
Soft
joints
48↓ 36↓ 24↓ 13↓ 6.4↓ 12↓ 9.6↓ 5.6↓ 4↓
Torque accuracy (%) ±5%
Torque adjustment Internal adjustment
Duty cycle 1.0s ON 4.0s OFF
Unloaded
Speed n0
(r/min)±10%
HI 200 200 420 850 1200 350 550 850 1200
LO 130 130 270 550 800 220 350 550 800
Screw size
(mm)
Machine
screw
≤12 ≤12 ≤10 ≤8 5.0~6.0 ≤8 ≤6 5.0~6.0 4.0~5.0
Weight (Kg) 2.85kg 1.9kg 1.25kg
Length (mm)
530mm
＊
122 mm
L
＊
H w/o battery
460mm
＊
92 mm
L
＊
H w/o battery
400mm
＊
92 mm
L
＊
H w/o battery
KILEWS
torque meter
KTM-
1000
KTM-
1000
KTM-
1000
KTM-
250
KTM-
150
KTM-
250
KTM-
150
KTM-
150
KTM-
150
Applicable Bit Type
W 1/2"sq
W 1/2"sq
W 3/8"sq
W 3/8"sq
B
W 3/8"sq
B
W 3/8"sq
B
W 3/8"sq
B
B
B
Applicable battery
SKC-LB1840
SKC-LB1820C
SKC-LB1820B
Applicable charger
station
MYCS-ID120
MYCS-ID80
MYCS-ID80-D MYCS-ID80-D
Applicable Bit type