MyWam Grizzly User manual

Operation and Maintenance Manual
Edition: 6 / 2021-05-10
The specialist stroller Grizzly
A modern rehabilitation stroller with perfect driving properties

GRIZZLY edition 6 / 2021-05-10
2 | P A G E
ATTENTION! Users with visual, reading or cognitive
impairment are requested to report to the
Manufacturer in order to obtain information in the
appropriate format.
Purpose of the Manual
The operation and maintenance manual contains basic information necessary for the correct use of the
Grizzly stroller, including the principles of safe use, description of its construction, operation and
adjustment, preparation of the stroller for operation, how to maintain and clean the stroller as well as
warranty conditions.
It is designed for people who directly take care of children with disabilities (childcare assistants, parents,
guardians), which will be transported in a stroller. It is also intended for doctors and physiotherapists
operating the stroller.
ATTENTION! Before using the stroller, each User is obliged to read the manual and act in accordance
with its guidelines.
This manual is an integral part of the product and must always be attached to the product wherever
being sold. Keep this manual for future reference! Keep the manual in an easily accessible place. The
manual in the electronic version is available on the website www.mywam.eu.
ATTENTION! In the event of any medical incidents related to the presence of the Grizzly stroller, the
Manufacturer must be immediately notified in writing by contacting it via registered letter or e-mail
with acknowledgment of receipt.
Manufacturer's contact details:
● Postal address: MyWam sp.j., ul. Szczecińska 10, 41-516 Chorzów, Poland
● contact phone number: [phone]
● e-mail address: [email protected]
User and maintenance manual version: EN Edition:6 Date: 2021-05-10
MyWam Kupiec, Bartold, Angres sp.j. reserves the right to make technical and commercial changes to the content
of the Operation and Maintenance Manual without prior notice. Each change will be determined by the date the
instructions were last updated.

GRIZZLY edition 6 / 2021-05-10
3 | P A G E
TABLE OF CONTENTS
 Introduction .......................................................................................................................................... 6
1. Intended use of the Grizzly stroller .................................................................................................... 6
2. Quick start .......................................................................................................................................... 6
 Safety..................................................................................................................................................... 7
3. Important instructions and safety rules............................................................................................ 7
4. Identification plate ............................................................................................................................. 9
5. Warning Lables ................................................................................................................................... 9
6. Description of symbols ....................................................................................................................... 9
 Product ................................................................................................................................................ 10
7. General construction of the stroller ................................................................................................ 10
7.1. The elements of the specialist stroller Grizzly include: ............................................................ 10
7.2. Therapeutic seat with backrest ................................................................................................ 11
7.3. Accessories................................................................................................................................ 11
8. Detailed description of construction and regulation ....................................................................... 12
8.1. Mechanism of frame assembly ................................................................................................. 12
8.2. Frame disassembly ................................................................................................................... 12
8.3. Frame assembly ........................................................................................................................ 12
8.4. Transport lock ........................................................................................................................... 12
8.5. Locking and unlocking the transport lock ................................................................................. 13
8.6. Front swiveling wheels ............................................................................................................. 13
8.7. Front wheel quick-release mechanism ..................................................................................... 13
8.8. Front wheel assembly ............................................................................................................... 13
8.9. Front wheel disassembly ......................................................................................................... 14
8.10. Front wheel drive lock........................................................................................................... 14
8.11. Switching on/off the front wheel drive lock ......................................................................... 14
8.12. Rear wheels ........................................................................................................................... 14
8.13. Quick-assembly mechanism for rear axle wheels................................................................. 14
8.14. Assembly and disassemble of rear axle wheels .................................................................... 15
8.15. Quick-assembly rear wheel mechanism ............................................................................... 15
8.16. Assembly and disassembly of the rear wheels on the frame. .............................................. 15
8.17. Rear wheel suspension system ............................................................................................. 15
8.18. Ergonomic handle to push the stroller ................................................................................. 16
8.19. Push handle angle adjustment mechanism .......................................................................... 16
8.20. Angular adjustment of the push handle ............................................................................... 16
8.21. Central brake ......................................................................................................................... 16
8.22. Switching the central brake on and off ................................................................................. 16
8.23. Tilting foot ............................................................................................................................. 16
8.24. Frame clips for seat mounting .............................................................................................. 17
8.25. Seat mounting mechanism to stroller frame ........................................................................ 17
8.26. Seat assembly ........................................................................................................................ 18
8.27. Seat disassembly ................................................................................................................... 19
8.28. Adjustable therapeutic seat .................................................................................................. 20

GRIZZLY edition 6 / 2021-05-10
4 | P A G E
8.29. Seat depth adjustment.......................................................................................................... 20
8.30. Seat width adjustment .......................................................................................................... 20
8.31. Mechanism of angle adjustment of the seat, so called cradle . ........................................... 21
8.32. Angular adjustment of the seat ............................................................................................ 22
8.33. Adjustable backrest ............................................................................................................... 23
8.34. Adjustable backrest height ................................................................................................... 23
8.35. Angle adjustment mechanism for the backrest .................................................................... 23
8.36. Angular adjustment of the backrest ..................................................................................... 24
8.37. Five-point harness ................................................................................................................. 25
8.38. Adjustment of five-point harness ......................................................................................... 25
8.39. Adjustable footrest ............................................................................................................... 25
8.40. Adjustable footrest plate height. .......................................................................................... 26
8.41. Angular adjustment of footplate. ......................................................................................... 26
8.42. Angular adjustment mechanism for the whole footrest ...................................................... 26
8.43. Angular adjustment of the entire footrest. .......................................................................... 27
8.44. Adjustable headrest supports in three planes ...................................................................... 27
8.45. Thoracic and lumbar supports with adjustment in three places .......................................... 28
8.46. Hip supports adjustable in three planes ............................................................................... 28
8.47. . Side elements of the backrest ............................................................................................. 29
8.48. Abduction & Stabilization harness ........................................................................................ 30
8.49. Safety barrier (put in the place of the therapeutic table) .................................................... 31
8.50. Adjustable canopy with window .......................................................................................... 31
8.51. Therapeutic table (mounted in the place of the safety barrier) ........................................... 32
8.52. Travel bag .............................................................................................................................. 32
8.53. Shopping basket .................................................................................................................... 33
8.54. Wedge ................................................................................................................................... 33
8.55. Rain cover (placed on the adjustable booth with a window) ............................................... 33
8.56. Winter gloves ........................................................................................................................ 33
8.57. Sleeping bag for legs (installed on the safety barrier) .......................................................... 34
8.58. Mosquito net (placed on the canopy)................................................................................... 34
8.59. Umbrella ................................................................................................................................ 34
8.60. Exclusive decorative set - Grizzly Bear (mounted on other accessories) ............................. 34
9. Technical specification of the Grizzly ............................................................................................... 35
9.1 Material composition of the stroller ............................................................................................. 35
10. Delivery and tools ......................................................................................................................... 35
11. Assembly and disassembly ........................................................................................................... 36
12. Preparation for use....................................................................................................................... 37
13. Transport of stroller ..................................................................................................................... 38
14. Getting in and out of the stroller ................................................................................................. 39
15. Correct position in the stroller ..................................................................................................... 39
16. Driving the stroller ........................................................................................................................ 39
17. Moving on sloping surfaces .......................................................................................................... 39
18. Overcoming thresholds or curbs .................................................................................................. 39

GRIZZLY edition 6 / 2021-05-10
5 | P A G E
19. Transport by car and other vehicles ............................................................................................. 40
20. Using the stroller as a seat in a motor vehicle ............................................................................. 40
21. Cleaning and care ......................................................................................................................... 45
22. Corrosion protection .................................................................................................................... 45
23. Preparation of the stroller for long-term storage ........................................................................ 46
24. Repeated use ................................................................................................................................ 46
25. Maintenance and periodic inspections ........................................................................................ 46
26. Disposal ........................................................................................................................................ 47
27. Compliance with the requirements for medical devices ............................................................. 48
28. Notes ............................................................................................................................................ 49
29. List of authorized service points .................................................................................................. 50
30. Warranty Card .............................................................................................................................. 51

GRIZZLY edition 6 / 2021-05-10
6 | P A G E
 Introduction
Thank you for purchasing special Grizzly stroller for older children. We hope that it will be the cause
of many wonderful moments with your child and will be helpful every day. We make every effort to
ensure that our products meet your expectations and the highest standards. We encourage you to
contact our employees and follow us on our website www.mywam.eu and on social media. There you
can find out many interesting things about our products.
1. Intended use of the Grizzly stroller
"Grizzly" is a multifunctional stroller designed for children with disabilities. The stroller is based on a
frame made of aluminum and steel elements. It allows for a quick disassembly of the wheels. "Grizzly" is
a complete therapeutic system that allows you to adjust the angle of the backrest and footrest, the
length of the footrest, position headrest, etc. The product is equipped with a number of accessories
improving the functionality and comfort of use, such as: table, safety belts, wedge, canopy, mosquito
net, sleeping bag, shopping bag, etc. Users cannot drive the stroller alone, but only with the help of a
guardian. The stroller can be used indoors and outdoors, on various surfaces (asphalt, concrete, stone,
gravel) and in various weather conditions. Any other use of the product than described above is
forbidden. The stroller must be used together with the instructions for use only by adults caring for the
user. Young people and children as well as any other peopole without proper training should not use the
product.
The "Grizzly" stroller is a medical device indicated for use by disabled children who, due to their health
condition, cannot walk or sit up unaided.
The product is intended for the transport and movement of the above mentioned people in a sitting or
lying position and for posture correction and this is its intended use. Clinical indications include cerebral
palsy, meningeal hernia, dystrophies, paresis, etc. The product is intended for users aged 3 to 12 years.
The product should be used in accordance with the recommendations of the attending physician or
physiotherapist.
Basic information about the Grizzly stroller
The Grizzly stroller has many options, e.g.:
 Reclining back (see point 8.33)
 backrest height adjustment (see point 8.34)
 seat angle adjustment (tilt in space) (see point 8.31 & 8.32)
 seat depth adjustment (see point 8.29)
 footrest adjustment (see point 8.39 & 8.43)
 head stabilization (see point 8.44)
 torso stabilization (see point 8.45 & 8.46)
 using the stroller as a seat in an adapted vehicle (see point 20)
2. Quick start
To quickly use the stroller it must be unpacked and prepared for use according to item 11 Assembly and
disassembly of the stroller and item 12 Preparation for use. The following is a pictorial diagram, but it
will not replace careful reading of the complete manual.

GRIZZLY edition 6 / 2021-05-10
7 | P A G E
 Safety
3. Important instructions and safety rules
General tips:
 It is forbidden to use the stroller in a way for which the stroller is not dedicated.

GRIZZLY edition 6 / 2021-05-10
8 | P A G E
 The product contains small parts that can be dangerous if swallowed by child!
 Due to the vast adjustment possibilities of the stroller, during the angular adjustment of the seat
as well as angular adjustment of the backrest, it is possible to set the position in which the child's
head is below the pelvic line. It is forbidden to use this position as it could lead to the risk of the
child choking.
 It is forbidden to put additional weight on the stroller, especially when it comes to placing an
additional weight on the back of the backrest, e.g. a backpack or a bag. This may cause the Grizzly
stroller to tip over and injure the user! It does not apply to original additional accessories dedicated
to the Grizzly stroller that do not exceed the permissible load. All additional elements attached to
the stroller affect its stability.
 ATTENTION! Depending on the adjustments made on the stroller - i.e. push handle position,
backrest height, back recline, seat depth, seat angle (tilt in space , footrest angle and length - this
stroller may exceed the maximum dimensions.
 ATTENTION! Each time the stroller is used, the steps listed below must be performed and the
stroller must not be used in the event of any irregularities. In such a situation, it is recommended
to urgently contact the Seller and the Manufacturer for advice.
 ATTENTION! When driving through doors or similar restrictions restricting the direction of travel
of the stroller, make sure that there is adequate space on both sides of the stroller to prevent
pinching of hands or other body parts and to prevent damage to the stroller.
ATTENTION!
 Never leave your child unattended in a stroller, as there is a risk of injury
or an accident!
 This product is not suitable for running, skating or roller-skating
 Beware of gaps and moving parts – risk of jamming
 Do not carry the stroller with the child inside it
 The stroller is packed in a plastic bag. The plastic bag is not a toy and
should be kept away from infants and young children as it may cause
suffocation when put on a head.
ATTENTION! It is forbidden to use the stroller if the technical condition of the stroller or a single
element of the stroller is in a bad condition or the user has any doubts about its condition, the
stroller is damaged or there is a suspicion that damage has occurred or if the operation of the
stroller is not correct. In such situation, it is recommended to urgently contact Seller and
Manufacturer for advice.

GRIZZLY edition 6 / 2021-05-10
9 | P A G E
4. Identification plate
 The identification plate contains the basic information
about the product such as: name, model, serial number
(ID no.), maximum load, manufacture date, CE mark,
and also certain warnings in accordance with the
operating and maintenance manual and manufacturer's
data (see Fig. 4.1).
 The identification plate is glued on the left, upper side
of stroller central brake beam (part of the frame in the
rear).
5. Warning Lables
 The warning plate contains important warnings for the
user (see Fig. 5.1).
 The warning plate is is glued on the left, upper side of
stroller central brake beam (part of the frame in the
rear).
6. Description of symbols
Product serial number The manufacturer's name
Permitted total user weight
DESCRIPTION "WARNING!" and the
symbol in this manual are used to
enhance the reader's attention to the
content marked with this sign. Non-
compliance with content marked with
this description may endanger the
health and safety of the user and
accompanying people, and may also
damage the product.
Date of manufacture
Conformity assessment mark
according to applicable
European regulations and
directives
Warning about proceeding in
accordance with the product
Operation and Maintenance
Manual
Fig. 4.1.
Fig..5.1.

GRIZZLY edition 6 / 2021-05-10
10 | P A G E
 Product
7. General construction of the stroller
The specialist stroller Grizzly consists of two main parts: frame and therapeutic seat with backrest.
Grizzly offers a wide range of accessories that help to meet individual needs of the users.
Frame is made of steel and is enriched with aluminum elements.
7.1. The elements of the specialist stroller Grizzly include:
Frame assembly mechanism (see Fig.7.1. and no. 14)
Transport lock (see Fig.7.1. and no. )
Front swivel wheels (see Fig.7.1. and no. 7)
Front wheel quick-release mechanism (see Fig.7.1. and no. 5)
Front wheel drive lock (see Fig.7.1. and no. 4)
Rear wheels (see Fig.7.1. and no. 9)
Quick-release mechanism for rear axle wheels (see Fig.7.1. and no. 8)
Quick-release rear wheel mechanism (see Fig.7.1. and no. 13)
Rear wheel suspension system (see Fig.7.1. and no. 12)
Ergonomic handle to push the stroller (see Fig.7.1. and no. 1)
Push handle angle adjustment mechanism (see Fig.7.1. and no. 2)
Central brake (see Fig.7.1. and no. 11)
Tilting foot (see Fig.7.1. and no. 10)
Frame hooks for seat mounting (see Fig.7.1. and no. 3)
Seat angular adjustment mechanism (so-called tilt/cradle) (see Fig.7.1. and no. 6)
Fig.7.1. Fig.7.2.

GRIZZLY edition 6 / 2021-05-10
11 | P A G E
7.2. Therapeutic seat with backrest
Its elements include:
Adjustable therapeutic seat (see Fig.7.2. and no.3 and on point 8.28)
Seat mounting mechanism (see Fig.7.2. and no.6 and on point 8.25)
Adjustable backrest (see Fig.7.2. and no.1 and on point 8.33)
Angular adjustment mechanism of the backrest (recline) (see Fig.7.2. and no.7 and on point 8.35)
Five-point harness (see Fig.7.2. and no.2 and on point 8.37)
Adjustable footrest (see Fig.7.2. and no.4 and on point 8.39)
Footrest angular adjustment mechanism (see Fig.7.2. and no.5 and on point 8.42)
7.3. Accessories
Head supports (see on point 8.44 )
Thoracolumbar supports (see on point 8.45)
Hip supports (see on point 8.46)
Side elements of the backrest (see on point 8.47)
Restraint-stabilization harness (see on point 8.48)
Security frame (see on point 8.49)
Adjustable canopy with a window (see on point 8.50)
Therapeutic table (see on point 8.51)
Travel bag (see on point 8.52)
Shopping basket (see on point 8.53)
Wedge (see on point 8.54)
Rain cover (see on point 8.55)
Winter gloves (see on point 8.56)
Sleeping bag for legs (see on point 8.57) Fig.7.3.
Mosquito net (see on point 8.58)
Umbrella (see on point 8.59)
Exclusive decorative set - Grizzly Bear (see on point 8.60)

GRIZZLY edition 6 / 2021-05-10
12 | P A G E
8. Detailed description of construction and regulation
8.1. Mechanism of frame assembly
The frame folding mechanism is located inside the frame and on the frame in
three places in its left part and in three places in its right side. Describing these
places from the top, from the stroller pushing handle, they are:
a) frame folding lock - a handle for locking and unlocking the frame folding
option, which has a red lock built in on the right part of the frame (see Fig. 8.1)
b) right and left frame swivel - element fixing the upper frame with the bottom
frame (see Fig.8.1.)
c) right and left twister- an element that allows the upper frame to be folded
down to reduce its dimensions (see Fig.8.1.)
8.2. Frame disassembly
To unfold the stroller frame: place the frame horizontally on the ground so that
the pushing handle is at the top, then remove the transport lock (see 8.5
Mounting and removing the transport lock) and pull up the stroller pushing
handle (see Fig. 8.2.) until hearing a clear click. The frame will be properly
disassembled only when the folding mechanism of the frame is properly closed.
This is evidenced by the clear "click" sound coming from the well-closed frame
folding mechanism.
8.3. Frame assembly
To fold the stroller frame: Push the red folding frame locking button (see section
8.1 Frame folding mechanism) and simultaneously pull both frame folding
handles upward towards the push handle (see Fig. 8.3). Then fold the frame
forward, in the direction of the front wheel mounting, then attach the transport
lock.
8.4. Transport lock
The stroller is equipped with a transport lock which serves to secure the folded
(closed) frame of the stroller prior to its automatic opening during transport and
storage.
The transport lock consists of two parts (see Fig.8.4): an eyelet and a pin.
Fig. 8.1.
Fig. 8.2
Fig. 8.3
Fig. 8.4

GRIZZLY edition 6 / 2021-05-10
13 | P A G E
8.5. Locking and unlocking the transport lock
In order to secure the frame against its accidental opening,
the frame must first be folded (see 8.3. Frame assembly) and
then place the lock eyelet on the locking pin so that both of
these elements close over each other.
To unlock the transport lock, before unfolding the frame, pull
the lock eyelet out of the locking pin, and then you can
proceed with unfolding of the frame.
8.6. Front swiveling wheels
Grizzly wheels are of finest quality and guarantee both the
highest driving comfort of as well as elegant look of the
stroller. The tires are tubeless and filled with a special gel
where level of shock-absorbtion is very similar to the one in
pumped wheels. The wheels are pre-assembled in the forks
which are ended with front wheel steering axle from the top
(see Fig.8.6).
Both front wheels can be set for driving straight ahead or
unlocked for turning, which makes handling of the stroller
much easier (see 8.10. Front wheel drive lock).
8.7. Front wheel quick-release
mechanism
The mechanism is mounted on the front
ends of the frame and ensures fast
assembly and dismounting of the front
wheels. It is activated by pressing the
quick disassembly button down, towards
the ground (see Fig. 8.7). The wheel is
mounted from below through a vertical
hole.
8.8. Front wheel assembly
Mount both front wheels axis as shown
on the picture (see Fig. 8.8) . Once done
slightly rotate the wheels to get the
characteristic click sound – now the wheels are properly mounted.
Fig. 8.5
Fig. 8.6
Rys 8.7
Rys 8.8

GRIZZLY edition 6 / 2021-05-10
14 | P A G E
8.9. Front wheel disassembly
When disassembling the front wheel, press the button located at the top of
the quick disassembly mechanism of the front wheels. Then slide the steering
wheel axle out of the quick-disassembly mechanism of the front wheels (see
Fig.8.9.). Repeat for the second wheel.
8.10. Front wheel drive lock
With the front wheel lock (see Fig. 8.10) and the possibility of assembling or
disassembling it, when pushing stroller, the bigger comfort of both the child
and the assistant is clearly noticeable.
It is advisable to remove the lock and allow the front wheels to be tilted
while driving the stroller on a completely smooth surface such as in shopping
centers, schools. On the other hand, in the case of inferior surfaces, moving
on inclined surfaces, when crossing thresholds or curbs, it is recommended to
mount a lock and locking the turning of front wheels.
8.11. Switching on/off the front wheel drive lock
To lock the turning of the front wheels, turn the knob of the directional lock
to the left (see Fig.8.11.).
To unlock the turning of the front wheels, turn the directional lock knob to
the right.
8.12. Rear wheels
Rear wheels (see Fig. 8.12) are of finest quality and guarantee both the highest driving comfort of as
well as elegant look of the stroller. The tires are tubeless and filled with a special gel where level of
shock-absorbtion is very similar to the one in pumped wheels.
Due to dismountable wheels and axis, you may gain additional space that will make it easier for you to
transport and store the stroller.
8.13. Quick-assembly mechanism for rear axle wheels
The mechanism is mounted inside the rear wheels and ensures quick assembly and removal of the rear
wheels. It is launched by pressing the quick-release clamp downward towards the center of the wheel
(see Fig. 8.13), then the rear wheel can be fitted to the rear wheel axle or the rear wheel can be taken
off from the rear wheel axle.
Fig. 8.11 Fig. 8.12 Fig. 8.13 Fig. 8.14
Fig 8.10
Fig 8.9

GRIZZLY edition 6 / 2021-05-10
15 | P A G E
8.14. Assembly and disassemble of rear axle wheels
When attaching the rear wheel to the rear wheel axle, push
the clamp on the center of the wheel and mount the wheel to
the top of its axle (see Fig. 8.14). Then stop pressing on the
clamp and continue inserting the wheel on its axle until it
clicks. Correct mounting of the wheel means a clear "click"
sound coming from the quick-release mechanism of the rear
wheel axle.
To disassemble the rear wheel from the rear wheel axle, press
the buckle on the center of the wheel and slide the wheel off
its axle.
8.15. Quick-assembly rear wheel mechanism
The mechanism is mounted on the rear end of the frame, in
contact with the cross-beam and ensures quick assembly and
removal of the rear wheels. It is launched by pressing the
quick-release button downward toward the ground (see Fig.
8.15). The wheel in this mechanism is mounted from the side,
from the outside, through the horizontal opening.
8.16. Assembly and disassembly of the rear wheels on the
frame.
 Assembly of the rear wheels to the stroller frame
Place both rear wheels together with their axles in the opening
of the mechanism. Then press the quick-release button to
allow the axle to slide, then slide the wheel with the axle into
the hole until it clicks (see Fig.8.16.). The "click" sound comes
from the appropriate mounting of the quick-wheel mechanism
on the frame. To make sure that the assembly is correct, check that the wheel with the axle cannot slide
out of the holes of the mechanism back outside.
During assembly of the rear wheels on the frame, make sure to hold the wheel at its inner rim and to
not push on the quick-assembly clamp of the rear wheel axle as it poses a threat of automatic
disassembly of the rear wheel from the rear wheel axle
 Removing the rear wheels from the stroller frame. When disassembling the rear wheel, push the
rear wheel quick-release button then holding the wheel behind its inner rim slide the wheel with
its axle our parallel to the ground.
8.17. Rear wheel suspension system
The stroller is equipped with a spring-loaded and rear wheel suspension, located in the rear ends of the
frame, in contact with the cross-beam (see Fig. 8.17). It should not be regulated. Suspension is
automatic.
Rys 8.15
Rys 8.16
Rys 8.17

GRIZZLY edition 6 / 2021-05-10
16 | P A G E
8.18. Ergonomic handle to push the stroller
The handle (see Fig.8.18) is used to push the stroller, providing a
secure grip in a variety of driving conditions. It has the possibility of
adjusting the height of the handle for childcare assistant pushing
the stroller.
8.19. Push handle angle adjustment
mechanism
These are two buttons on the outer side
of the frame, located on the joints of
the push handle (see Fig. 8.19.).
8.20. Angular adjustment of the push
handle
To change the tilting angle of the stroller handle, push both knobs of the tilt
angle adjustment mechanism of the push handle and change its tilt angle
(see Fig.8.20.). When the handle is in the correct position, stop pressing the
buttons, which will automatically lock the handle to the desired position.
8.21. Central brake
The central brake pedal the pressing of which directly locks the two rear
wheels of the stroller, is located in the center of the cross-beam in the rear
of the stroller frame.).
8.22. Switching the central brake on and off
In order to activate the central brake, press the brake pedal down, towards
the ground, until it clicks (see Fig.8.22). A clear "click" sound is proof of the
central brake being activated correctly.
To switch off the central brake, pull the brake pedal up.
8.23. Tilting foot
The tilting foot is on the right side of the cross-beam in the rear of the rehab
stroller frame (see Fig. 8.23). To use it, press the tilting foot and
simultaneously pull the pushing handle of the stroller, which in turn will
raise the front wheels up.
Using the tilting foot facilitates the entry of the stroller to small thresholds
or curbs.
Fig 8.18
Fig.8.19
Fig. 8.20
Fig..8.21.
Fig..8.22
Fig. 8.23

GRIZZLY edition 6 / 2021-05-10
17 | P A G E
8.24. Frame clips for seat mounting
There are two colored, chrome, transverse hooks that are
located on the stroller frame in its center (see Fig. 8.24).
These two frame rods are very important elements in the
construction of the stroller. They are used to connect the
therapeutic seat with the backrest to the frame of the
stroller.
In order to distinguish them from the gray frame
reinforcements, they have been marked with a color so that
the person assembling the seat to the frame, uses these
colored hooks and does not make a mistake, and does not
accidentally assemble the seat to the gray frame
reinforcements, because it is forbidden and incorrect.
8.25. Seat mounting mechanism to stroller frame
The seat mounting mechanism to stroller frame is located at
the bottom the stroller seat.
It consists of:
a) transverse handle (see Fig.8.25, no. 4)
b) two locks of the mechanism (see Fig.8.25, no. 2 and 6)
c) two front seat mountings (see Fig.8.25, no. 1 and 7)
d) two rear seat mountings (see Fig.8.25, no. 3 and 5)
It is used both to mount/dismount the seat to/from the frame as well as to keep it locked in the frame .
 Unlocking the seat mechanism from the frame
To unlock the mechanism, pull the transverse handle backwards and open the lock (see Fig.8.25.A), then
continue pulling the transverse handle backwards and upwards, causing the lock to stop in an open
position (see Fig.8.25.B).
 Locking the seat mechanism
In order to close the lock mechanism, the seat must be mounted correctly on the stroller frame (see
section 8.26 Seat assembly), which will cause the lock to slam shut into a closed position (see
Fig.8.25.C.).
Fig..8.25.A Fig..8. 25.B Fig. 8.25.C
Fig.8.24.
Fig. 8.25

GRIZZLY edition 6 / 2021-05-10
18 | P A G E
8.26. Seat assembly
The seat can be mountedfacing or back to the the direction of travel. To mount the seat to the frame,
perform the following steps in the following order:
a) activate the central brake so that the stroller frame is stable and immobilized (see Fig.8.26.-A)
b) set the stroller frame hooks to
the seat assembly in a 0°
position (see Fig.8.26.-B and see
8.32. Angular seat adjustment)
c) make sure that the seat
mounitng mechanism to the
stroller frame is in a position
with an open lock (see Fig. 8.26.-
C and see 8.25.1. Opening the
lock in the seat mounting
mechanism)
d) then apply both REAR seat
mounting to the first frame hook
(see Fig.8.26.-D)
Fig..8.26.-A - CORRECT Fig..8.26.-A' – WARNING, WRONG!
Fig..8.26.-B CORRECT Fig..8.26.-B' - WARNING, WRONG!
Fig..8.26.-C - CORRECT Fig..8.26.-C' - WARNING, WRONG!
Fig..8.26.-D - CORRECT Fig..8.26.-D' - WARNING, WRONG!

GRIZZLY edition 6 / 2021-05-10
19 | P A G E
e) then apply the two FRONT seat
mountings to the other frame hook
(see Fig.8.26.-E)
f) then press both FRONT seat
mounting to the other frame hook
until there are two clicks (see
Fig.8.26.-F).
The correct seating assembly is
marked by the "click" sound coming
from the two closing locks of the seat
mounting mechanism to the frame of
the stroller.
8.27. Seat disassembly
To remove the seat from the frame, proceed as follows in the determined
sequence:
a) Activate the central brake so that the stroller is stable and immobilized (see
Fig.8.27.-A)
b) set the seat inclination angle to a 0° position, i.e. the seat plane is set parallel
to the ground (see Fig.8.27.-B and see 8.32. Angular seat adjustment)
c) pull the transverse grip of the rear seat mounting mechanism backwards,
which starts the opening of the locking of the seat mounting mechanism (see
Fig.8.27.-C)
d) pull the transverse handle of the mounting mechanism of the seat backwards which starts the
opening of the locking mechanism of the seat mounting, then continue pulling the transverse handle
backwards and upwards, causing the seat locking mechanism to stop in an open position (see Fig.8.27.-
D)
Fig.8.27.-B Fig.8.27.-C Fig.8.27.-D
Fig..8.26.-E - CORRECT Fig..8.26.-E' – WARNING! WRONG!
Fig..8.26.-F - CORRECT Fig..8.26.-F' – WARNING! WRONG!

GRIZZLY edition 6 / 2021-05-10
20 | P A G E
e) then remove both FRONT mounitngs of the seat from the
hooks of the frame, by lifting the front of the seat upwards,
from the ground (see Fig.8.27.-E)
f) then pull both REAR backrest mountings of the seat from
the hooks of the frame, by lifting the back of the seat at an
angle forward, to the front of the seat and up, from the
ground (see Fig.8.27.-F)
8.28. Adjustable therapeutic seat
The Grizzly stroller has a
multifunctional, adjustable therapeutic seat (see Fig.8.28.), which at the rear is
connected with an adjustable backrest and an adjustable footrest at the front.
Both the backrest and the accessories are covered with high quality upholstery
available in various colors.
The therapeutic seat in the Grizzly stroller has the following options:
a) change in the angle of inclination of the seat relative to the ground (see 8.32.
Angular adjustment of the seat)
b) adjustment of the depth (see 8.29. Seat depth adjustment)
c) adjustment of the useable width (see 8.30. Seat width adjustment)
d) ilial stabilization (see 8.48. Restraint-stabilization belts)
e) maintenance of the child's limbs in an opposing position (see 8.54. Wedge)
f) and other functions according to user needs (see 7.3. Accessories)
8.29. Seat depth adjustment
Seat depth adjustment can be accomplished by partially unscrewing (loosening) two knobs, which are
located on the seat from the bottom (see Fig.8.29.-A), and then separating the seat back to the desired
position (see Fig.8.29.-B). Be careful not to unscrew the knobs completely, as this will remove the lock
and risk complete removal
of the seat plates. After
completing the adjustment,
tighten both knobs until you
feel the resistance (see
Fig.8.29.-C).
The range of fluent
adjustment of seat depth is
about 120mm, where at the
minimum setting, the seat
depth is 25cm and at a
maximum it is 37cm.
8.30. Seat width adjustment
The seat width function can be used through accessories: hip supports with adjustment in three planes.
The range of smooth adjustment of the seat width is from 180 to 320mm. If accessories are not
purchased or the supports are not assembled, then the width of the seat itself is fixed at 400mm.
Fig.8.27.-E Fig.8.27.-F
Fig.8.28
Fig.8.29.-A Fig.8.29.- B Fig.8.29.-C