MyWam in.basic Mewa User manual

PODSTAWA 1 / 2022-09-09
1 |Page
Operating manual
Addition to the operating manuals for
particular special needs strollers
1st Edition / 2022-09-09
Indoor base in.basic
Additional equipment to special needs strollers
Mewa/Mouse/ Grizzly

INDOOR BASE in.basic 1st Edition / 2022-09-09
2 |Page
Unfolding of the indoor base
Pick up the folded frame, lock the brakes, unfold the lateral support and tighten it with the star knobs at the
bottom of the frame (Pict. 1)
(Pict. 1)
Unfold the crossbeams, set the required angle and tighten the star knobs fixing it to the main frame.
(Pict. 2-5).
Pict. 2 Pict. 3
Pict. 4 Pict. 5

INDOOR BASE in.basic 1st Edition / 2022-09-09
3 |Page
Height of the handle should be adjusted in accordance with needs of the user (Pict. 6 – 7). In order to change
its angle press buttons located at both sides of the handle and set the new position afterwards.
Mewa/Mouse
Mounting of the seat
Seat can be mounted backwards or forwards towards the direction of travel. In order to mount the seat:
a) Lock the brakes to fix the indoor base in a static and stable position (Pict. 8-9).
Pict. 8 Correct Pict. 9 Incorrect
b) Put the seat on the indoor base mounts and push it until characteristic “click” sound appears.
The “click” sound coming from both sides of the locking mechanism is a signal for a proper installation of the
seat (Pict. 10-11).

INDOOR BASE in.basic 1st Edition / 2022-09-09
4 |Page
Pict. 10 Pict. 11
Dismounting of the seat
In order to dismount the seat, press the two white buttons located at both sides of the frame towards the ground
(Pict. 12). Next pull the seat out of the seat mounts.
Pict. 12
Grizzly
Seat can be mounted backwards or forwards towards the direction of travel.
In order to mount the seat proceed in accordance with the sequence as below:
a) Lock the brakes to fix the indoor base in a static and stable position (Pict. 13-14).
Pict. 13 Correct Pict. 14 Incorrect

INDOOR BASE in.basic 1st Edition / 2022-09-09
5 |Page
b) Fix the adapter on the frame mounts and push it until characteristic “click” sound appears.
The “click” sound coming from both sides of the locking mechanism a signal for a proper installation of the
adapter (Pict. 15-16).
Pict. 15 Pict. 16
c) Fix both of the rear seat mounts on the rear part of the indoor base adapter (Pict.17).
Pict. 17
d) Pull back the seat rear crossbeam to unlock the front clamp (Pict. 17) and fix both of the front seat mounts
to the front part of the indoor base adapter
e) Lock the front mounts of the seat.
The “click” sound coming from both sides of the locking mechanism signals proper installation of the seat on the
adapter (Pict. 18).
Pict. 18
Seat dismount

INDOOR BASE in.basic 1st Edition / 2022-09-09
6 |Page
In order to dismount the seat proceed in accordance with the sequence as below:
a) Lock the brakes to fix the indoor base in a static and stable position
b) pull back the rear crossbeam to unlock the front seat mount (Pict. 19).
Pict. 19
c) while the front seat mount is being unlocked tilt the seat back and pull it up to take it off from the frame
Height adjustment
The height adjustment mechanism is located inside of the left and right arm of the frame. In order to change the
height:
• unlock both of the clamps (Pict. 20) (both clamp handles should be turned right)
Pict. 20
• adjust proper height using the scale from 1-6 (Pict. 21-22).

INDOOR BASE in.basic 1st Edition / 2022-09-09
7 |Page
Pict.21 Pict. 22
ATTENTION!Before locking the height mechanism make sure both left and right arm are at the same height!
• lock the clamps (clap handles should be turned left) (Pict. 23) and push the frame to check if the height
adjustment mechanism is locked properly.
Pict. 23
ATTENTION! All adjustments of both indoor base and its elements must be carried out without the user
sitting in the base. Failure to comply with this requirement may cause serious threat for the health of the
user!
Folding of the indoor base

INDOOR BASE in.basic 1st Edition / 2022-09-09
8 |Page
Before folding the indoor base make sure to lock the brakes and set the handle in the exit position (Pict. 24)
Pict. 24
In order to fold the base first remove the seat and set it at the lowest possible height (i.e. marked with number
1). Then unscrew the star knobs on both sides of the frame, take out the screws and fold the seat crossbeams
(Pict. 25).
Pict. 25
Next unscrew the star knobs located at the bottom of the frame, take out the screws, fold the crossbeams to
the inside and fold the frame (Pict. 26). Lock the frame using the velcro strap (Pict. 27).
Pict. 26 Pict. 27
ATTENTION! Indoor base is desinged to be used at home. Indoor base can be used on flat surface (no curbs
and drops).

INDOOR BASE in.basic 1st Edition / 2022-09-09
9 |Page
ATTENTION! All adjustments of both indoor base and its elements must be carried out without the user
sitting in the base. Failure to comply with this requirement may cause serious threat for the health of
the user!
Plates
Technical specification of the indoor base
length of the indoor base
95 cm
width of the indoor base
58 cm
height of the indoor base
104 cm
total weight
7,5 kg
seat height regulation
53 - 71 cm
length of the base folded for transport
107 cm
width of the base folded for transport
57 cm
height of the base folded for transport
22 cm
max. patient weight Mouse / Mewa / Grizzly
30 / 40 / 45 kg
height of the patient Mouse / Mewa / Grizzly
80-110 cm / 90-125 cm / 85-140 cm
•Please read the manual carefully before using the product
•
Leaving child without an adult supervision may result in
serious injury
•
ATTENTION! Indoor base is designed to be used at home.
Indoor base can be used on flat surface (no curbs and drops)
•
Beware of gaps and moving parts – danger of entrapment.
•
ATTENTION! All adjustments of both indoor base and its
elements must be carried out without the user sitting in the
base. Failure to comply with this requirement may cause
serious threat for the health of the user!
WARNING: