Napoleon EF34H User manual

1
W415-0405/B/03.25.04
INSTALLER: THESE INSTRUCTIONS MUST BE CONVEYED TO AND REMAIN WITH THE HOMEOWNER.
Wolf Steel Ltd., 24 Na oleon Rd., Barrie, ON L4M 4Y8 Canada • [phone] • fax[phone]
www.na oleonfire laces.com • ask@na oleon.on.ca
INSTALLATION AND OPERATION INSTRUCTIONS FOR
ELECTRIC FIREPLACE HEATER
MODELS
EF34H
EF36H
CERTIFIED UNDER CANADIAN AND AMERICAN NATIONAL STANDARDS, CSA C2.22 No46 / UL1278 CSA STANDARD.
WARNING: IF THE INFORMATION IN THESE INSTRUCTIONS IS NOT FOLLOWED EXACTLY,
AN ELECTRICAL SHOCK OR FIRE MAY RESULT CAUSING PROPERTY DAMAGE, PERSONAL
INJURY OR LOSS OF LIFE.
FOR YOUR SAFETY
DO NOT STORE OR USE GASOLINE OR OTHER FLAMMABLE VAPOURS AND
LIQUIDS IN THE VICINITY OF THIS OR ANY OTHER APPLIANCE.
R-2000

2
W415-0405/B/03.25.04
9 ELECTRICAL CONNECTION
10-11 REPLACEMENTS
Ordering Replacement Parts
Replacement Parts
Accessories
11 TROUBLE SHOOTING GUIDE
12 SERVICE HISTORY
PLEASE RETAIN THIS MANUAL FOR FUTURE REFERENCE
NOTE: Changes, other than editorial, are denoted by a vertical line in the margin.
WARNING
••
••
• Do not burn wood or other materials in this fireplace.
• Adults and especially children should be alerted to the hazards of high surface temperatures of the louvres
and heater area and should stay away to avoid burns or clothing ignition. Supervise young children when
they are in the same room as the fireplace.
• Due to high temperatures, the fireplace should be located out of traffic and away from combustible mate-
rial; such as furniture and draperies.
• lothing or other flammable material should not be placed on or near the fireplace.
• Any safety screen or guard removed for servicing must be replaced prior to operating the fireplace.
• It is imperative that the control compartments, circulating blower and its passageway in the fireplace are
kept clean. More frequent cleaning may be required due to excessive lint from carpeting, bedding material,
etc. The fireplace area must be kept clear and free from combustible materials, gasoline and other flamma-
ble vapours and liquids.
• Under no circumstances should this fireplace be modified.
• Do not use this fireplace if any part has been under water. Immediately call a qualified service technician to
inspect the fireplace and to replace any part of the control system which has been under water.
• Do not operate the fireplace with the glass door removed, cracked or broken. Use only with a glass door
certified with the fireplace.
• Do not strike the fireplace glass door.
PG 2-4 INTRODUCTION
Warranty
Important Instructions
Locating Your Fireplace
Dimensions
5 OPERATION
Remote Control
Flame Effect
Maintenance
6-8 FINISHING
Mantel Installation
Clearance to Combustibles
Framing and Finishing
Hearth
Cold Climate Installation
Log Installation
Louvres
Screen Cover Removal
TABLE of CONTENTS
PLEASE RETAIN THIS MANUAL FOR FUTURE REFERENCE

3
W415-0405/B/03.25.04
NAPOLEON electric fireplaces are manufactured under the strict Standard of the world recognized
ISO 9001:2000 Quality Assurance Certificate.
NAPOLEON products are designed with superior components and materials, assembled by trained craftsmen
who take great pride in their work. Once assembled the complete fireplace is thoroughly inspected by a qualified
technician before packaging to ensure that you, the customer, receive the quality product that you expect from
NAPOLEON.
NAPOLEON ELECTRIC FIREPLACE LIMITED WARRANTY
Electrical components and wearable parts such as fan/heater, motors, switches, nylon bear-Electrical components and wearable parts such as fan/heater, motors, switches, nylon bear-
Electrical components and wearable parts such as fan/heater, motors, switches, nylon bear-Electrical components and wearable parts such as fan/heater, motors, switches, nylon bear-
Electrical components and wearable parts such as fan/heater, motors, switches, nylon bear-
ing components and remote controls are covered and Napoleon will provide replacement partsing components and remote controls are covered and Napoleon will provide replacement parts
ing components and remote controls are covered and Napoleon will provide replacement partsing components and remote controls are covered and Napoleon will provide replacement parts
ing components and remote controls are covered and Napoleon will provide replacement parts
free of charge during the first year of the limited warranty.free of charge during the first year of the limited warranty.
free of charge during the first year of the limited warranty.free of charge during the first year of the limited warranty.
free of charge during the first year of the limited warranty.
Light bulbs are NOT covered by the warranty.Light bulbs are NOT covered by the warranty.
Light bulbs are NOT covered by the warranty.Light bulbs are NOT covered by the warranty.
Light bulbs are NOT covered by the warranty.
Any labour related to warranty repair is not covered.Any labour related to warranty repair is not covered.
Any labour related to warranty repair is not covered.Any labour related to warranty repair is not covered.
Any labour related to warranty repair is not covered.
CONDITIONS AND LIMITATIONS
NAPOLEONwarrants itsproducts againstmanufacturing defectsto theoriginal purchaseronly --i.e., theindividual orlegal entity(registered customer)whose nameappears onthe
warrantyregistrationcard filedwithNAPOLEON -- providedthatthe purchasewasmade through anauthorized NAPOLEONdealerand is subjecttothe followingconditionsandlimitations:
Thisfactory warranty isnontransferableand maynotbe extended whatsoeverbyany ofourrepresentatives.
Installationmust bedone inaccordance withthe installationinstructions includedwith theproduct andall localand nationalbuilding andfire codes.
Thislimited warranty doesnotcover damagescausedby misuse,lackof maintenance,accident,alterations, abuseorneglect and partsinstalled from othermanufacturers will nullifythis
warranty.
Thislimited warranty furtherdoes notcoverany scratches,dents,corrosion ordiscolouringcaused byexcessiveheat, abrasiveandchemical cleanersnorchipping onporcelainenamel
parts, mechanicalbreakage of PHAZER™ logsand embers.
Inthe firstyearonly,this warrantyextendsto therepairorreplacement ofwarrantedparts which aredefective in materialor workmanshipprovidedthat theproduct has beenoperated in
accordancewith theoperation instructions andunder normalconditions.
Napoleonwill notbe responsiblefor installation,labour orany otherexpenses related tothe reinstallationof a warrantedpartand suchexpenses arenot covered bythis warranty.
Notwithstandinganyprovisionscontainedinthis LimitedWarranty, NAPOLEON’Sresponsibilityunderthiswarranty isdefinedasaboveand itshallnotinanyevent extendtoanyincidental,
consequentialor indirectdamages.
Thiswarranty definesthe obligations and liability of NAPOLEON withrespect tothe NAPOLEONelectric fireplaceand anyother warrantiesexpressed orimplied withrespect tothis
product,its componentsor accessoriesare excluded.
Napoleonneither assumes,nor authorizesany thirdparty to assume, on it'sbehalf, anyother liabilitieswith respectto thesaleof theproduct.
Anydamages to fireplace, brass trim orother component dueto water,weather damage,long periods of dampness, condensation,damaging chemicalsor cleanerswill not be the
responsibilityof NAPOLEON.
Thebill ofsaleor copywill be requiredtogether withaserial numberand amodelnumber whenmaking any warrantyclaims fromyour authorized dealer.The warrantyregistrationcard
mustbe returnedwithinfourteen daysto registerthewarranty.
NAPOLEONreserves theright tohave itsrepresentative inspect any product orpart thereofprior tohonouring anywarranty claim.
ALLSPECIFICATIONSANDDESIGNSARESUBJECTTOCHANGE WITHOUT PRIORNOTICEDUETOON-GOING PRODUCTIMPROVEMENTS.NAPOLEON® ISAREGISTERED
TRADEMARKOFWOLF STEELLTD. PATENTSU.S.5.303.693.801-CAN.2.073.411, 2.082.915. ©WOLFSTEELLTD.

4
W415-0405/B/03.25.04
Your new fireplace may be installed into an existing ma-
sonry or zero clearance fireplace. It may also be installed
using a prefabricated cabinet available from your dealer or
may be built into a wall. For the best effect, install the fire-
place out of direct sunlight.
1.READ ALLINSTRUCTIONSBEFOREUSINGTHIS APPLI-
ANCE.THISAPPLIANCE ISHOTWHEN USED.
2. To avoid burns, DO NOT let bare skin touch hot surfaces.
The trim around the heat outlet becomes hot during fire-
place operation. Keep combustible material; such as fur-
niture, pillows, bedding, paper, clothes and draperies at
least 3 feet from the front of the unit.
3. CAUTION: Extreme caution is necessary when any fire-
place is used by or near children or invalids, also when-
ever the heater is left operating and unattended.
4. Do not operate if the power cord or fireplace is dam-
aged, or if the unit is dropped or damaged in any manner.
5. Under no circumstances should this fireplace be modi-
fied. Use it only as described in the manual. Any repairs to
the fireplace should be carried out by a qualified service
person.
6. Do not use outdoors.
7. Do not insert or allow foreign objects to enter any venti-
lation or exhaust openings as this may cause an electrical
short or fire. This could also damage the fireplace.
8. To prevent a possible fire, DO NOT block air intakes or
exhaust in any manner. DO NOT use on soft surfaces where
openings may become blocked.
9. This heater has hot and arcing or sparking parts inside.
DO NOT use in areas where gasoline, paint or flammable
liquids are used or stored. This fireplace SHOULD NOT be
used as a drying rack.
10. This fireplace is NOT intended for wood or other flam-
mable material to be burned inside of it.
11. Make sure the fireplace is unplugged before any clean-
ing or maintenance is performed on the heater.
12. Avoid the use of extension cords. The extension cord
may overheat and cause a fire.
13. Do not strike the glass on the fireplace.
14. Always unplug heater when not in use.
15. This heater is not intended for use in bathrooms, laun-
dry areas and similar indoor locations. Never locate heater
where it may fall into a bathtub or other water container.
16. Do not run cord under carpeting. Do not cover cord with
throw rugs, runners or similar coverings.Arrange cord away
from traffic area and where it will not be tripped over.
17. To disconnect heater, turn controls to off, then remove
the plug from the outlet.
18. Use this heater only as described in this manual. Any
other use not recommended by the manufacturer may
cause fire, electric shock or injury to persons.
19. SAVE THESE INSTRUCTIONS.
IMPORTANT INSTRUCTIONS LOCATING YOUR ELECTRIC FIREPLACE
EF34 DIMENSIONS
EF36 DIMENSIONS

5
W415-0405/B/03.25.04
This fireplace is supplied with a radio frequency remote
control. This remote will function up to 20 feet away from
the fireplace.
The heater may emit a slight, harmless odour when first
used. This odour is a normal condition caused by initial
heating of internal heater parts. Thereafter, any odour is
normally the result of household dust settling on the
heater element.
1. Turn the main power on at the control panel.
2. Using the hand held remote, turn the power on at the
remote. If the unit does not turn on, you will need to syn-
chronize the codes.
To synchronize the codes:
Press and hold the on button on the hand held remote.
Press the learn button on the control panel. See CON-
TROL PANEL on page 9. Simultaneously hold both but-
tons in for approximately 5 seconds.
To change the code on the transmitter:
a) Press the button under the battery compartment lid on
the transmitter.
b) Remove the battery from the transmitter and turn "off"
the main power on the control panel.
c) Wait 5 seconds and reinstall the battery and turn "on"
the power.
d) While pressing the "on" button on the hand held re-
mote, press the "learn" button on the control panel. See
CONTROLPANELon page9.
e) Hold both in for approximately 5 seconds.
3. To turn the unit off, use either the remote or main power
button on the control panel or the manual on/off button on
the control panel.
4. The thermostat, located on the lower control panel, is
used to control the temperature of the room. To increase
the temperature, turn the dial clockwise.
Bulb Replacement : If you notice the flame look is darker
on one side of the fireplace, check the light bulbs to en-
sure that one has not burned out.
Bulb must be replaced with a MAX 60 watt incandes-
cent clear light bulb.
1. To replace the bulb, turn the circuit breaker off or unplug
the appliance.
2. Open the lower louvres.
3. Detach the light access panel by removing the four
screws.
4. Replace the burned out light bulb using a new 60 watt
clear incandescent bulb.
5. Replace access panel.
6. Turn on the power or plug the appliance back in.
7. Turn on the main power and test.
OPERATION
MAINTENANCE
The flame generator has a random modulating control
which causes the flame effect to speed up and slow down
sporadically. This action creates the realistic flame ap-
pearance and can not be modified.
FLAME EFFECTREMOTE CONTROL

6
W415-0405/B/03.25.04
Sides.................0 mm / 0 inches
Sides.................0 mm / 0 inches
Floor................. 0 mm / 0 inches
Top 0 mm / 0 inches
The minimum distance from the top of the unit that the
mantel can be installed is 0", at any depth.
When using paint or lacquer to finish theWhen using paint or lacquer to finish the
When using paint or lacquer to finish theWhen using paint or lacquer to finish the
When using paint or lacquer to finish the
mantel, such paint or lacquer must be heatmantel, such paint or lacquer must be heat
mantel, such paint or lacquer must be heatmantel, such paint or lacquer must be heat
mantel, such paint or lacquer must be heat
resistant to prevent discolouration.resistant to prevent discolouration.
resistant to prevent discolouration.resistant to prevent discolouration.
resistant to prevent discolouration.
Sides.........................0 inches
Back..........................0 inches
Floor..........................0 inches
Top............................0 inches
1. Choose fireplace location.
2. Place fireplace in position.
3. Frame in fireplace with header across the top. It is impor-
tant to allow for the finished facing materials when setting
the depth of the frame. 4. Remove the two screws
from the sides of the fire-
place and attach the nail-
ing tabs with the screws.
5. To determine the final
location of the nailing tab,
you must first determine
the thickness of your fin-
ishing material (i.e.
sheetrock/drywall) This will determine the dimension from
the control panel front edge to the nailing tab. Secure with a
sheet metal screw supplied.
6. Attach the nailing tabs to the frame.
MANTEL FRAMING AND FINISHING
CLEARANCE TO COMBUSTIBLES
Nailing
Tab
Installation
FINISHING
Sheet
Metal
Screw

7
W415-0405/B/03.25.04
Corner Installation
EF34
Corner Installation
Front View
EF36
Note: In order to avoid the possibility of exposed insulation or vapour barrier coming in contact with the
fireplace body, it is recommended that the walls of the fireplace enclosure be “finished” (ie: drywall/sheetrock), as you
would finish any other outside wall of a home. This will ensure that clearance to combustibles is maintained within the
cavity.
Top View
Front View
Top View

8
W415-0405/B/03.25.04
A A
A A
A hearth is NOT necessaryhearth is NOT necessary
hearth is NOT necessaryhearth is NOT necessary
hearth is NOT necessary but is recommended for aes-but is recommended for aes-
but is recommended for aes-but is recommended for aes-
but is recommended for aes-
thetic purthetic pur
thetic purthetic pur
thetic purposesposes
posesposes
poses..
..
.
WARNING:WARNING:
WARNING:WARNING:
WARNING: It is MANDIt is MAND
It is MANDIt is MAND
It is MANDAA
AA
ATT
TT
TOROR
OROR
OR to ha to ha
to ha to ha
to havv
vv
ve an insulae an insula
e an insulae an insula
e an insulated wted w
ted wted w
ted wall be-all be-
all be-all be-
all be-
hind the fireplace, when the fireplace is being installedhind the fireplace, when the fireplace is being installed
hind the fireplace, when the fireplace is being installedhind the fireplace, when the fireplace is being installed
hind the fireplace, when the fireplace is being installed
on an outside won an outside w
on an outside won an outside w
on an outside wall or call or c
all or call or c
all or chasehase
hasehase
hase..
..
.
1. Position log #1 as shown, so that the bottom end is
pressed against the left inner side of the chamber. The log
base is moulded to cradle the underside of log #1, allow-
ing it to rest diagonally, as shown.
2. For correct positioning of log #2, the top end of log #1
must be lifted up off the base, as shown.
3. The bottom end of log #2 is pressed against the inner
right side of the chamber. The underside branch of log #2
fits under the top end of log #1.
Once logs are in final position, close the screen.
A
B
C
D
LOG BASE
#1
#2
COLD CLIMATE INSTALLATION
HEARTH
LOG INSTALLATION
#2
#1
HOOD
Attach the hood by pressing the
top flange into the clips along
the top of the louvre opening.
Secure using a screw through
the centre slot.
LOWERLOUVRES
Insert the hinge clips into the
slots located at the bottom left
and right corners of the unit.
To remove the louvres, pull the
back tabs of the clips forward,
while pushing the louvre assem-
bly back. Lift the clip.
UPPERLOUVRES
Insert the louvre tabs into the
slots located at the top left and
right corners of the unit.
L334 LOUVRE INSTALLATION
C
B
A
CHINGE
CLIP SLOT
SLOT
TAB
B
ACLIPS
CENTRE
SLOT
FLANGE
SCREEN COVER REMOVAL
1. Remove the upper
louvre (shown with
louvre removed).
2. Remove the screw
securing the
screen cover.
3. Un-hook the screen
cover from the unit.
2
3
1

9
W415-0405/B/03.25.04
This fireplace requires a 15 amp, 120 volt and 60 hz
circuit that is grounded to the electrical socket. The fire-
place should e on its own circuit. If there are other
appliances on the same circuit, this may cause the cir-
cuit reaker or fuse to low when the fireplace heater is
in operation.
The unit comes with a 6' electrical cord, exiting the top
right side. Plan your installation to avoid the use of an
extension cord. If you require an extension cord, it must
e at least 16 awg wire and e rated for 2025 watts.
Electrical outlet wires must comply with local uilding
codes to reduce the risk of fire, electrical shock and
injury.
Do NOT use the fireplace if any part has een under
water.
Call a qualified service technician IMMEDIATELY to have
the fireplace inspected for damage to the electrical cir-
cuit.
If it is necessary to hard wire this fireplace, a qualifiedIf it is necessary to hard wire this fireplace, a qualified
If it is necessary to hard wire this fireplace, a qualifiedIf it is necessary to hard wire this fireplace, a qualified
If it is necessary to hard wire this fireplace, a qualified
electrician may remove the cord connection, and wireelectrician may remove the cord connection, and wire
electrician may remove the cord connection, and wireelectrician may remove the cord connection, and wire
electrician may remove the cord connection, and wire
this unit directly to the house hold wiring.this unit directly to the house hold wiring.
this unit directly to the house hold wiring.this unit directly to the house hold wiring.
this unit directly to the house hold wiring.
Permanently framing the fireplace with an enclosure, re-
quires the fireplace to be hardwired.
This fireplace must be electrically connected and grounded
in accordance with local codes. In the absence of local
codes, use the current CSA C22.1 CANADIAN ELECTRI-
CALCODEinCanadaortheANSI/NFPA70-1996NATIONAL
ELECTRICAL CODE in the United States.
1.1.
1.1.
1. Power (Rocker Switch)Power (Rocker Switch)
Power (Rocker Switch)Power (Rocker Switch)
Power (Rocker Switch)
2.2.
2.2.
2. Thermostat SwitchThermostat Switch
Thermostat SwitchThermostat Switch
Thermostat Switch
3.3.
3.3.
3. Fan / Heater AssemblyFan / Heater Assembly
Fan / Heater AssemblyFan / Heater Assembly
Fan / Heater Assembly
4.4.
4.4.
4. Main Circuit BoardMain Circuit Board
Main Circuit BoardMain Circuit Board
Main Circuit Board
5.5.
5.5.
5. DC Motor (flame effect)DC Motor (flame effect)
DC Motor (flame effect)DC Motor (flame effect)
DC Motor (flame effect)
6.6.
6.6.
6. Main Power CordMain Power Cord
Main Power CordMain Power Cord
Main Power Cord
7.7.
7.7.
7. Strain ReliefStrain Relief
Strain ReliefStrain Relief
Strain Relief
8.8.
8.8.
8. Flame Effect Light (two light sockets-Flame Effect Light (two light sockets-
Flame Effect Light (two light sockets-Flame Effect Light (two light sockets-
Flame Effect Light (two light sockets-60 watts max60 watts max
60 watts max60 watts max
60 watts max))
))
)
9.9.
9.9.
9. Nylon Cable TieNylon Cable Tie
Nylon Cable TieNylon Cable Tie
Nylon Cable Tie
10. Learn Button10. Learn Button
10. Learn Button10. Learn Button
10. Learn Button
11. Manual on/off Button11. Manual on/off Button
11. Manual on/off Button11. Manual on/off Button
11. Manual on/off Button
ELECTRICAL CONNECTION
HARD WIRING CONNECTION
Electric Diagra
ELECTRICAL DIAGRAM LEGEND
10
CONTROLPANEL
11 1 2

10
W415-0405/B/03.25.04
# PART NO. DESCRIPTION
1 W497-0001 PLASTIC DIFFUSER
2 W062-0016 FAN / HEATER ASSEMBLY
3 W380-0013 THERMOSTATKNOB
4 W385-0277 CONTROLPANELLABEL
5 W387-0001 60 WATT LIGHT BULB
6 W435-0004 FLAME EFFECT MOTOR
7 W660-0022 THERMOSTATSWITCH
8 W660-0023 MAIN POWER SWITCH
9 W660-0037 REMOTE RECEIVER
10 W660-0038 REMOTETRANSMITTER
11 W010-1090 FLAME EFFECTASSEMBLY
12* W045-0001 NYLON BEARING
13 GL-637 LOGSET
14 W135-0173 LOG #1
15 W135-0174 LOG #2
Use only accessories designed for and listed with the
EF34 & EF36H models.
# PART NO. DESCRIPTION
16 CDV3-4L LOUVRE OVERLAY - POLISHED BRASS
16 CDV3-24L LOUVRE OVERLAY - POLISHED BRASS
16 CDV3-4LSS LOUVRE OVERLAY - STAINLESS STEEL
16 CDV3-24LSS LOUVRE OVERLAY - STAINLESS STEEL
17 L334K LOUVRE ASSEMBLY - BLACK
18* GD33B-KT BAY KIT
17 L36K LOUVRE KIT - UPPER & LOWER - BLACK
19 HOIK-2 HERITAGE ORNAMENTAL INSETS - BLACK
19 HOIG-2 HERITAGE ORNAMENTAL INSETS - GOLD PLATED
19 HOIKG-2 HERITAGE ORNAMENTAL INSETS - BLACK GOLD PLATED
19 HOIBC-2 HERITAGE ORNAMENTAL INSETS - BRUSHED COPPER PLATED
19 HOIBG-2 HERITAGE ORNAMENTAL INSETS - BRUSHED GOLD PLATED
20 DOIK-1 DIAMOND ORNAMENTAL INSETS - BLACK
20 DOIG-1 DIAMOND ORNAMENTAL INSETS - GOLD PLATED
20 DOIKG-1 DIAMOND ORNAMENTAL INSETS- BLACK GOLD PLATED
20 DOIBC-1 DIAMOND ORNAMENTAL INSETS- BRUSHED COPPER PLATED
20 DOIBG-1 DIAMOND ORNAMENTAL INSETS- BRUSHED GOLD PLATED
21 GOIK-1 GOTHIC ORNAMENTAL INSETS - BLACK
21 GOIG-1 GOTHIC ORNAMENTAL INSETS - GOLD PLATED
21 GOIKG-1 GOTHIC ORNAMENTAL INSETS - BLACK GOLD PLATED
21 GOIBC-1 GOTHIC ORNAMENTAL INSETS - BRUSHED COPPER PLATED
21 GOIBG-1 GOTHIC ORNAMENTAL INSETS - BRUSHED GOLD PLATED
22 SOIK-1 SEASHELL ORNAMENTAL INSETS - BLACK
22 SOIG-1 SEASHELL ORNAMENTAL INSETS - GOLD PLATED
22 SOIKG-1 SEASHELL ORNAMENTAL INSETS - BLACK GOLD PLATED
22 SOIBC-1 SEASHELL ORNAMENTAL INSETS -BRUSHED COPPER PLATED
22 SOIBG-1 SEASHELL ORNAMENTAL INSETS - BRUSHED GOLD PLATED
23 EOIK-1 ECLIPSE ORNAMENTAL INSETS - BLACK
23 EOIG-1 ECLIPSE ORNAMENTAL INSETS - GOLD PLATED
23 EOIKG-1 ECLIPSE ORNAMENTAL INSETS - BLACK GOLD PLATED
23 EOIBC-1 ECLIPSE ORNAMENTAL INSETS - BRUSHED COPPER PLATED
23 EOIBG-1 ECLIPSE ORNAMENTAL INSETS - BRUSHED GOLD PLATED
24* DK36-R DOOR KIT, RECTANGULAR - BLACK
24* DK36-RG DOOR KIT, RECTANGULAR - GOLD PLATED
25* DK36-A DOOR KIT, ARCHED - BLACK
25* DK36-AG DOOR KIT, ARCHED - GOLD PLATED
26* DK36-W DOOR KIT, WEBBED - BLACK
26* DK36-WG DOOR KIT, WEBBED - GOLD PLATED
Contact your dealer for questions concerning prices and
availability of replacement parts. Normally all parts can be
ordered through your Napoleon dealer or distributor.
When ordering replacement parts always give the follow-
ing information:
1. MODEL &SERIAL NUMBER OF FIREPLACE
2. INSTALLATION DATE OF FIREPLACE
3. PART NUMBER
4. DESCRIPTION OF PART
5. FINISH
FORFOR
FORFOR
FOR WARRANTYWARRANTY
WARRANTYWARRANTY
WARRANTY REPLREPL
REPLREPL
REPLAA
AA
ACEMENTCEMENT
CEMENTCEMENT
CEMENT PP
PP
P
ARAR
ARAR
ARTSTS
TSTS
TS, ,
, ,
, AA
AA
A PHOPHO
PHOPHO
PHOTT
TT
TOCOPYOCOPY
OCOPYOCOPY
OCOPY OFOF
OFOF
OF
THETHE
THETHE
THE
ORIGINALORIGINAL
ORIGINALORIGINAL
ORIGINAL INVOICEINVOICE
INVOICEINVOICE
INVOICE WILLWILL
WILLWILL
WILL BEBE
BEBE
BE REQUIREDREQUIRED
REQUIREDREQUIRED
REQUIRED TOTO
TOTO
TO HONOURHONOUR
HONOURHONOUR
HONOUR THETHE
THETHE
THE
CLAIMCLAIM
CLAIMCLAIM
CLAIM..
..
.
REPLACEMENTS
* IDENTIFIES ITEMS WHICH ARE NOT ILLUSTRATED. FOR
FURTHER INFORMATION, CONTACT YOUR NAPOLEON
DEALER.
REPLACEMENT PARTS
EF34 ACCESSORIES
EF36 ACCESSORIES

11
W415-0405/B/03.25.04
2
3
5
7
6
8
14
15
13
11
1
4
17
23
19
20
22
21
16
10
9

12
W415-0405/B/03.25.04
Flame light, but no - Flame generator motor has burned out. - Consult your local dealer.
movement in the flame - Flame generator has come loose. - Remove the access panel and check to make
sure the flame generator is in the flame
generator bracket, and is secured to the
motor with the rubber tube.
No Flame Light but - Light bulbs have burned out. - Remove access panel and change
everything else is light bulbs.
working properly.
Remote control - Dead batteries. - Make sure batteries are charged.
not working - No power to the unit. - Make sure main power is on.
- Power turned off. - Turn on manual power switch.
- Remote needs to be synchronized - Push the learn button on the control panel
with receiver. at the same time you push the on button on
the remote.
Heater works but - Fan on heater is not working. - Consult your local dealer.
there is no air flow.
Fan works but there is - Heater is not working. - Consult your local dealer.
no heat.
Fireplace will not - Breaker or fuse has blown. - Check main power switch is turned on.
turn on. - Consult your local dealer.
TROUBLE SHOOTING GUIDE
SYMPTOM PROBLEM TEST SOLUTION
Heater does not turn off. - Thermostat is set to high. - Turn thermostat counter-clockwise.
- Thermostat may be faulty. - Consult your local dealer.
Excessive noise coming - Dirt build up on fan bearing. - Consult your local dealer.
from the top of the unit. - Defective blower. - Vacuum the top control compartment.
Odour - Dust has settled on the - Run heater until odour ceases
heater element. (approx. 1/2 hr)
- Consult your local dealer.
Heater cycling on - Air intlets blocked. - Check to make sure there is nothing blocking
and off the air inlets on the bottom of the unit.
- Should not be on high pile carpet that can
block air inlets.
The fireplace turns off - Fuse may be loose - Consult your local dealer
when moved or bumped. (Remove the 5 screws from the control panel
and check that the fuse is not blown or loose.)