Napoleon GD16 - N User manual

1
WS-415-112/06.18.99
GAS - DIRECT VENT MILLIVOLGAS - DIRECT VENT MILLIVOL
GAS - DIRECT VENT MILLIVOLGAS - DIRECT VENT MILLIVOL
GAS - DIRECT VENT MILLIVOLT SYSTEMT SYSTEM
T SYSTEMT SYSTEM
T SYSTEM
INSTINST
INSTINST
INSTALLAALLA
ALLAALLA
ALLATION AND OPERATION AND OPERA
TION AND OPERATION AND OPERA
TION AND OPERATION INSTRUCTIONS FORTION INSTRUCTIONS FOR
TION INSTRUCTIONS FORTION INSTRUCTIONS FOR
TION INSTRUCTIONS FOR
VENTED GAS FIREPLACEVENTED GAS FIREPLACE
VENTED GAS FIREPLACEVENTED GAS FIREPLACE
VENTED GAS FIREPLACE
NATURAL GAS MODEL
GD16 - NGD16 - N
GD16 - NGD16 - N
GD16 - N
PROPANE GAS MODEL
GD16 - PGD16 - P
GD16 - PGD16 - P
GD16 - P
CERTIFIED FOR CANADA AND UNITED STATES USING ANSI / AGA / CGA METHODS
INSTINST
INSTINST
INSTALLER: THESE INSTRUCTIONS MUST BE CONVEYED TO AND REMAIN WITH THE HOMEOWNERALLER: THESE INSTRUCTIONS MUST BE CONVEYED TO AND REMAIN WITH THE HOMEOWNER
ALLER: THESE INSTRUCTIONS MUST BE CONVEYED TO AND REMAIN WITH THE HOMEOWNERALLER: THESE INSTRUCTIONS MUST BE CONVEYED TO AND REMAIN WITH THE HOMEOWNER
ALLER: THESE INSTRUCTIONS MUST BE CONVEYED TO AND REMAIN WITH THE HOMEOWNER
CERTIFIEDUNDERCANADIAN ANDAMERICAN NATIONALSTANDARDS, CSA 2.22,ANDANSI Z21.50RESPECTIVELYFOR VENTEDGAS FIREPLACES.
Fax: [phone] Email: [email protected]
Web: www.napoleon.on.ca
Wolf Steel Ltd., RR#1, 9 Napoleon Rd.,
Barrie, ON., Canada L4M 4Y8 [phone]
R-2000
WW
WW
WARNING:ARNING:
ARNING:ARNING:
ARNING: If the information in these instructions is not followed exactly, a fire or
explosion may result causing property damage, personal injury or death.
FOR YOUR SAFETYFOR YOUR SAFETY
FOR YOUR SAFETYFOR YOUR SAFETY
FOR YOUR SAFETY
Do not store or use gasoline or other flammable vapours and liquids in the vicinity of
this or any other appliance.
WHAWHA
WHAWHA
WHATT
TT
TTT
TT
TO DO IF YOU SMELLO DO IF YOU SMELL
O DO IF YOU SMELLO DO IF YOU SMELL
O DO IF YOU SMELL GAS:GAS:
GAS:GAS:
GAS:
• Do not try to light any appliance.
• Do not touch any electrical switch.
• Do not use any phone in your building.
• Immediately call your gas supplier from
a neighbor's phone. Follow the gas
supplier's instructions.
• If you cannot reach your gas supplier,
call the fire department.
Installation and service must be performed by a qualified installer, service
agency or the gas supplier.

2
WS-415-112/06.18.99
PLEASE RETPLEASE RET
PLEASE RETPLEASE RET
PLEASE RETAIN THIS MANUAL FOR FUTURE REFERENCEAIN THIS MANUAL FOR FUTURE REFERENCE
AIN THIS MANUAL FOR FUTURE REFERENCEAIN THIS MANUAL FOR FUTURE REFERENCE
AIN THIS MANUAL FOR FUTURE REFERENCE
TT
TT
TABLEABLE
ABLEABLE
ABLE ofof
ofof
of CONTENTSCONTENTS
CONTENTSCONTENTS
CONTENTS
PG 2-5PG 2-5
PG 2-5PG 2-5
PG 2-5 INTRODUCTIONINTRODUCTION
INTRODUCTIONINTRODUCTION
INTRODUCTION
Warranty
General Instructions
General Information
Care of Glass & Plated Parts
6-86-8
6-86-8
6-8 VENTINGVENTING
VENTINGVENTING
VENTING
Venting Lengths
Air Terminal Locations
99
99
9-1-1
-1-1
-155
55
5INSTINST
INSTINST
INSTALLAALLA
ALLAALLA
ALLATIONTION
TIONTION
TION
Wall & Ceiling Protection
Using Flexible Vent Components
Using Rigid Vent Components
Mobile Home Installation
Gas Installation
Framing
1616
1616
16 FINISHINGFINISHING
FINISHINGFINISHING
FINISHING
Door, Louvre & Trim Removal & Installation
Log Placement
PGPG
PGPG
PG1717
1717
17 OPTIONAL BLOWER INSTOPTIONAL BLOWER INST
OPTIONAL BLOWER INSTOPTIONAL BLOWER INST
OPTIONAL BLOWER INSTALLAALLA
ALLAALLA
ALLATIONTION
TIONTION
TION
1818
1818
18 OPTIONAL FOPTIONAL F
OPTIONAL FOPTIONAL F
OPTIONAL FAN INSTAN INST
AN INSTAN INST
AN INSTALLAALLA
ALLAALLA
ALLATION /TION /
TION /TION /
TION /
THERMOSTTHERMOST
THERMOSTTHERMOST
THERMOSTAA
AA
ATIC SENSOR CONTROLTIC SENSOR CONTROL
TIC SENSOR CONTROLTIC SENSOR CONTROL
TIC SENSOR CONTROL
11
11
199
99
9--
--
-2020
2020
20 OPERAOPERA
OPERAOPERA
OPERATION / MAINTENANCETION / MAINTENANCE
TION / MAINTENANCETION / MAINTENANCE
TION / MAINTENANCE
Operating Instructions
Maintenance
2020
2020
20 ADJUSTMENTSADJUSTMENTS
ADJUSTMENTSADJUSTMENTS
ADJUSTMENTS
Pilot Burner Adjustment
Venturi Adjustment
21-2221-22
21-2221-22
21-22 REPLACEMENTSREPLACEMENTS
REPLACEMENTSREPLACEMENTS
REPLACEMENTS
Ordering Replacement Parts
Replacement Parts
Vent Kits
Terminal Kits
Accessories
23-2423-24
23-2423-24
23-24 TROUBLE SHOOTING GUIDETROUBLE SHOOTING GUIDE
TROUBLE SHOOTING GUIDETROUBLE SHOOTING GUIDE
TROUBLE SHOOTING GUIDE

3
WS-415-112/06.18.99
NAPOLEON gas fireplaces are manufactured under the strict Standard of the world recognized
ISO9002 Quality Assurance Certificate.
NAPOLEON products are designedwith superior componentsand materials, assembledby trained craftsmenwho
take great pride in their work. The burner and valve assembly are leak and test-fired at a quality test station. The
complete fireplace is thoroughly inspected by a qualified technician before packaging to ensure that you, the
customer, receives the quality product that you expect from NAPOLEON.
NAPOLEON GAS FIREPLACE PRESIDENT'S LIFETIME LIMITED WARRANTYNAPOLEON GAS FIREPLACE PRESIDENT'S LIFETIME LIMITED WARRANTY
NAPOLEON GAS FIREPLACE PRESIDENT'S LIFETIME LIMITED WARRANTYNAPOLEON GAS FIREPLACE PRESIDENT'S LIFETIME LIMITED WARRANTY
NAPOLEON GAS FIREPLACE PRESIDENT'S LIFETIME LIMITED WARRANTY
The following materials and workmanship in your newThe following materials and workmanship in your new
The following materials and workmanship in your newThe following materials and workmanship in your new
The following materials and workmanship in your new NAPOLEONNAPOLEON
NAPOLEONNAPOLEON
NAPOLEON gas fireplace are war-gas fireplace are war-
gas fireplace are war-gas fireplace are war-
gas fireplace are war-
ranted against defects for as long as you own the fireplace. This covers: combustion chamber,ranted against defects for as long as you own the fireplace. This covers: combustion chamber,
ranted against defects for as long as you own the fireplace. This covers: combustion chamber,ranted against defects for as long as you own the fireplace. This covers: combustion chamber,
ranted against defects for as long as you own the fireplace. This covers: combustion chamber,
heat exchanger, stainless steel burner, phazer™ logs and embers, ceramic glass (thermal break-heat exchanger, stainless steel burner, phazer™ logs and embers, ceramic glass (thermal break-
heat exchanger, stainless steel burner, phazer™ logs and embers, ceramic glass (thermal break-heat exchanger, stainless steel burner, phazer™ logs and embers, ceramic glass (thermal break-
heat exchanger, stainless steel burner, phazer™ logs and embers, ceramic glass (thermal break-
age only), gold plated parts against tarnishing, porcelainized enamelled components and alumi-age only), gold plated parts against tarnishing, porcelainized enamelled components and alumi-
age only), gold plated parts against tarnishing, porcelainized enamelled components and alumi-age only), gold plated parts against tarnishing, porcelainized enamelled components and alumi-
age only), gold plated parts against tarnishing, porcelainized enamelled components and alumi-
num extrusion trims.num extrusion trims.
num extrusion trims.num extrusion trims.
num extrusion trims.
Electrical (110V and millivolt) components and wearable parts such as blowers, gas valves,Electrical (110V and millivolt) components and wearable parts such as blowers, gas valves,
Electrical (110V and millivolt) components and wearable parts such as blowers, gas valves,Electrical (110V and millivolt) components and wearable parts such as blowers, gas valves,
Electrical (110V and millivolt) components and wearable parts such as blowers, gas valves,
thermal switch, switches, wiring, remote controls, ignitor, gasketing, and pilot assembly arethermal switch, switches, wiring, remote controls, ignitor, gasketing, and pilot assembly are
thermal switch, switches, wiring, remote controls, ignitor, gasketing, and pilot assembly arethermal switch, switches, wiring, remote controls, ignitor, gasketing, and pilot assembly are
thermal switch, switches, wiring, remote controls, ignitor, gasketing, and pilot assembly are
covered andcovered and
covered andcovered and
covered and NAPOLEONNAPOLEON
NAPOLEONNAPOLEON
NAPOLEON will provide replacement parts free of charge during the first yearwill provide replacement parts free of charge during the first year
will provide replacement parts free of charge during the first yearwill provide replacement parts free of charge during the first year
will provide replacement parts free of charge during the first year
of the limited warranty.of the limited warranty.
of the limited warranty.of the limited warranty.
of the limited warranty.
Labour related to warranty repair is covered free of charge during the first year. RepairLabour related to warranty repair is covered free of charge during the first year. Repair
Labour related to warranty repair is covered free of charge during the first year. RepairLabour related to warranty repair is covered free of charge during the first year. Repair
Labour related to warranty repair is covered free of charge during the first year. Repair
work, however, requires the prior approval of an authorized company official. Labour costs towork, however, requires the prior approval of an authorized company official. Labour costs to
work, however, requires the prior approval of an authorized company official. Labour costs towork, however, requires the prior approval of an authorized company official. Labour costs to
work, however, requires the prior approval of an authorized company official. Labour costs to
the account ofthe account of
the account ofthe account of
the account of NAPOLEONNAPOLEON
NAPOLEONNAPOLEON
NAPOLEON are based on a predetermined rate schedule and any repair workare based on a predetermined rate schedule and any repair work
are based on a predetermined rate schedule and any repair workare based on a predetermined rate schedule and any repair work
are based on a predetermined rate schedule and any repair work
must be done through an authorizedmust be done through an authorized
must be done through an authorizedmust be done through an authorized
must be done through an authorized NAPOLEONNAPOLEON
NAPOLEONNAPOLEON
NAPOLEON dealer.dealer.
dealer.dealer.
dealer.
CONDITIONS AND LIMITCONDITIONS AND LIMIT
CONDITIONS AND LIMITCONDITIONS AND LIMIT
CONDITIONS AND LIMITAA
AA
ATIONSTIONS
TIONSTIONS
TIONS
NAPOLEON warrants its products against manufacturing defects to the original purchaser only -- i.e., the individual or legal entity (registered customer) whose name appears on the
warrantyregistration cardfiled with NAPOLEON --provided that thepurchase wasmade throughan authorized NAPOLEONdealer andis subjectto thefollowingconditions andlimitations:
Thisfactory warranty is nontransferable and may notbe extendedwhatsoever byany of our representatives.
Thegas fireplace must be installed by alicenced, authorizedservice technicianor contractor.Installation must be done inaccordance withthe installation instructions included with the
productand alllocal andnational building and fire codes.
Thislimited warrantydoes notcover damages caused by misuse,lack ofmaintenance, accident,alterations, abuseor neglectand partsinstalled from other manufacturers willnullify this
warranty.
This limited warranty further doesnot cover any scratches, dents, corrosion or discolouring causedby excessive heat, abrasive andchemical cleaners nor chipping on porcelain enamel
parts,mechanical breakage of PHAZER™ logsand embers,nor anyventing componentsused in the installation ofthe fireplace.
NAPOLEONwarrants itsstainless steelburners againstdefects in workmanship and materialfor life,subject tothe followingconditions: During thefirst 10years NAPOLEONwill replace
or repair the defective parts at our option free of charge. From 10 years to life, NAPOLEON will provide replacement burners at 50% of the current retail price.
Inthe firstyear only, this warranty extends to the repair or replacement of warranted parts which are defective in materialor workmanship provided that the product has been operated in
accordancewith theoperation instructionsand undernormal conditions.
Afterthe first year,with respect to this President'sLimited Lifetime Warranty, NAPOLEON may, at itsdiscretion, fullydischarge all obligations with respectto thiswarranty by refunding
tothe original warranted purchaser thewholesale priceof any warranted but defectivepart(s).
After thefirst year, NAPOLEON willnot beresponsible forinstallation, labour orany other costs orexpenses relatedto the reinstallationofa warranted part, and suchexpenses arenot
coveredby this warranty.
Notwithstandingany provisionscontained inthis President's Limited Lifetime Warranty,NAPOLEON’S responsibilityunder thiswarrantyis definedas aboveand itshall notin anyevent
extendto anyincidental, consequentialor indirect damages.
This warrantydefines theobligations andliability of NAPOLEONwith respect tothe NAPOLEON gasfireplace and anyother warrantiesexpressedor impliedwith respectto thisproduct,
itscomponents or accessories are excluded.
NAPOLEON neither assumes,nor authorizes anythird party to assume,on itsbehalf, any otherliabilities with respect tothe sale ofthis product.NAPOLEON will not be responsiblefor:
over-firing,downdrafts, spillagecaused byenvironmental conditionssuch asrooftops, buildings,nearby trees,hills, mountains,inadequate ventsor ventilation,excessive ventingconfigu-
rations, insufficient makeup air, or negative air pressures which may or may not be caused by mechanical systems such as exhaust fans, furnaces, clothes dryers, etc.
Any damages to fireplace, combustion chamber, heat exchanger, brass trim orother component due to water, weather damage, long periods of dampness, condensation, damaging
chemicals or cleaners will not be the responsibility of NAPOLEON.
Thebill ofsale or copy will be required togetherwith aserial numberand amodel numberwhen making any warranty claims from yourauthorized dealer.The warrantyregistration card
mustbe returned within fourteen daysto registerthe warranty.
NAPOLEONreserves the rightto haveits representative inspect any productor part thereof prior tohonouring any warranty claim.
ALLSPECIFICATIONS ANDDESIGNS ARESUBJECT TOCHANGEWITHOUT PRIORNOTICE DUE TO ON-GOING PRODUCTIMPROVEMENTS. NAPOLEON®IS AREGISTERED
TRADEMARK OF WOLF STEEL LTD. PATENTS U.S. 5.303.693.801 - CAN. 2.073.411, 2.082.915. © WOLF STEEL LTD.

4
WS-415-112/06.18.99
GENERAL INSTRUCTIONSGENERAL INSTRUCTIONS
GENERAL INSTRUCTIONSGENERAL INSTRUCTIONS
GENERAL INSTRUCTIONS
THIS GAS FIREPLACE SHOULD BE INSTALLED AND SERVICED BY A QUALIFIED INSTALLER to conform with local
codes.Inabsenceoflocalcodes,installtothecurrentNationalFuelGasCode,ANSIZ223.1,orthecurrentCAN/CGAB149,
Installation Codes. Mobile home installation must conform with local codes or in the absence of local codes, install to
the current standard for gas equipped mobile housing CAN/CSA ZA240 MH Series in Canada or the Manufactured
Home Construction and Safety Standard, Title 24 CFR, Part 3280, or the Fire Safety Criteria for Manufactured Home
Installations, Sites, and Communities Standard ANSI/NFPA 501A in the United States.
PURGEALLGASLINESWITHTHEGLASSDOOROFTHEFIREPLACEREMOVED.ASSURETHATACONTINUOUSGASFLOW
IS AT THE BURNER BEFORE INSTALLING THE DOOR.
UNDEREXTREMEVENTCONFIGURATIONS,ALLOWSEVERALMINUTES(5-15)FORTHEFLAMETOSTABILIZEAFTERIGNITION.
SIX (6") INCHES IS THE MINIMUM BEND RADIUS ALLOWED FOR THE 7" DIAMETER FLEXIBLE LINER.
The fireplace and its individual shutoff valve must be disconnected from the gas supply piping system during any
pressure testing of that system at test pressures in excess of 1/2 psig (3.5 kPa). The fireplace must be isolated from the
gas supply piping system by closing its individual manual shutoff valve during any pressure testing of the gas supply
piping system at test pressures equal to or less than 1/2 psig (3.5 kPa).
If the optional blower/ fan is installed, the receptacle / junction box must be electrically connected and grounded in
accordance with local codes. In the absence of local codes, use the current CSA C22.1 CANADIAN ELECTRICAL CODE
in Canada or the ANSI/NFPA 70-1990 NATIONAL ELECTRICAL CODE in the United States.
GENERAL INFORMAGENERAL INFORMA
GENERAL INFORMAGENERAL INFORMA
GENERAL INFORMATIONTION
TIONTION
TION
FOR YOUR SATISFACTION, THIS FIREPLACE HAS BEEN TEST-FIRED TO ASSURE ITS OPERATION AND QUALITY!
Maximum input is 17,000 BTU/hr for natural gas and propane. When the fireplace is installed at elevations above 4,500ft,
and in the absense of specific recommendations from the local authority having jurisdiction, the certified high altitude
input rating shall be reduced at the rate of 4% for each additional 1,000ft. Maximum output for natural gas is 12,500 BTU/
hr at an efficiency of 73.5% with the fan on, and 12,750 BTU/hr for propane at an efficiency of 75% with the fan on.
Minimum inlet gas supply pressure is 4.5 inches water column for natural gas and 11 inches water column for propane.
Maximum inlet gas pressure is 7 inches water column for natural gas and 13 inches water column for propane. Manifold
pressure under flow conditions is 3.5 inches water column for natural gas and 10 inches water column for propane.
This fireplace is approved for bathroom, bedroom and bed-sitting room installations and is suitable for mobile home
installation. The natural gas model can only be installed in a mobile home that is permanently positioned on its site and
fueled with natural gas.
CARE OF GLASS, AND PLACARE OF GLASS, AND PLA
CARE OF GLASS, AND PLACARE OF GLASS, AND PLA
CARE OF GLASS, AND PLATED PTED P
TED PTED P
TED PARAR
ARAR
ARTSTS
TSTS
TS
Do not use abrasive cleaners to clean plated parts. Buff lightly with a clean dry cloth. The glass is 3/16" tempered glass
available from your Napoleon / Wolf Steel Ltd. dealer. DO NOT SUBSTITUTE MATERIALS. Clean the glass after the first
10 hours of operation with a recommended gas fireplace glass cleaner. Thereafter clean as required. DO NOT CLEAN
GLASS WHEN HOT! If the glass is not kept clean permanent discolouration and / or blemishes may result.
NO EXTERNAL ELECTRICITY (110 VOLNO EXTERNAL ELECTRICITY (110 VOL
NO EXTERNAL ELECTRICITY (110 VOLNO EXTERNAL ELECTRICITY (110 VOL
NO EXTERNAL ELECTRICITY (110 VOLTS OR 24 VOLTS OR 24 VOL
TS OR 24 VOLTS OR 24 VOL
TS OR 24 VOLTS) IS REQUIRED FOR THE GAS SYSTEM OP-TS) IS REQUIRED FOR THE GAS SYSTEM OP-
TS) IS REQUIRED FOR THE GAS SYSTEM OP-TS) IS REQUIRED FOR THE GAS SYSTEM OP-
TS) IS REQUIRED FOR THE GAS SYSTEM OP-
ERAERA
ERAERA
ERATIONTION
TIONTION
TION. Expansion / contraction nosies during heating up and cooling down cycles are normal and
are to be expected.
Provide adequate ventilation air. Provide adequate accessibility clearance for servicing and operating the
fireplace. Never obstruct the front opening of the fireplace.
Use only accessories designed for and listed with the GD16 model.

5
WS-415-112/06.18.99
WW
WW
WARNINGARNING
ARNINGARNING
ARNING
••
••
• Do not burn wood or other materials in this fireplace.
• Adults and especially children should be alerted to the hazards of high surface temperatures and should stay
away to avoid burns or clothing ignition. Supervise young children when they are in the same room as the
fireplace.
• Due to high temperatures, the fireplace should be located out of traffic and away from furniture and draperies.
• Clothing or other flammable material should not be placed on or near the fireplace.
• Any safety screen or guard removed for servicing must be replaced prior to operating the fireplace.
• It is imperative that the control compartments, burners and circulating blower and its passageway in the fire-
place and venting system are kept clean. The fireplace and its venting system should be inspected before use
and at least annually by a qualified service person. More frequent cleaning may be required due to excessive
lint from carpeting, bedding material, etc. The fireplace area must be kept clear and free from combustible
materials, gasoline and other flammable vapours and liquids.
• Under no circumstances should this fireplace be modified.
• This fireplace must not be connected to a chimney flue pipe serving a separate solid fuel burning appliance.
• Do not use this fireplace if any part has been under water. Immediately call a qualified service technician to
inspect the fireplace and to replace any part of the control system and any gas control which has been under
water.
• Do not operate the fireplace with the glass door removed, cracked or broken. Replacement of the glass should
be done by a licensed or qualified service person. Use only with a glass door certified with the fireplace.
• Do not strike or slam shut the fireplace glass door.
FIGURE 1
For safe and proper operation of the fireplace follow the venting instruction exactly.
Deviation from the minimum vertical vent length can create difficulty in burner start-up and/or carboning.
Vent lengths that pass through unheated spaces (attics, garages, crawl spaces) should be insulated with the
insulation wrapped in a protective sleeve to minimize condensation.
Provide a means for visually checking the vent connection to the fireplace after the fireplace is installed.
Do not allowthe inside liner to bunch upon horizontalor vertical runs andelbows. Keep itpulled tight. A 1-1/4" air
gap between the inner and outer liner all around is required for safe operation.
Use a firestop when penetrating interior walls, floor or ceiling.
The fireplace must be installed against finished walls. Do not install against a vapour barrier or exposed insula-
tion.
Onallhorizontalruns,when determining airterminallocations, check forappropriateriseperfootrequirements.
Aterminalshallnot terminate directlyaboveasidewalk or paveddrivewaywhichis located betweeentwosingle
family dwellings and serves both dwellings. Local codes or regulations may require different clearances.
Do not allow the inside liner to bunch up on horizontal or vertical runs and elbows. Keep it pulled tight. A 1¼" air
gap all aroundbetween the inner linerand outer liner isrequired for safe operation.Use a firestop whenpenetrat-
inginteriorwalls,floor or ceiling.

6
WS-415-112/06.18.99
Horizontal runs may have a 0 inch rise per foot using Simpson Dura-Vent, Napoleon rigid or flexible venting
components when venting as illustrated in Figure 2a-c.
Except for rigid venting directly off the back of the fireplace as illustrated in FIGURES 2a, 2d &3, all other venting
configurations may have the combustion air deflector removed to improve the flame pattern. See Trouble Shooting for
removal details.
Whenventing, thehorizontal runmust bekept toaminimum of 8inches or amaximum of
24inches.Ifagreaterhorizontalrunisrequired,thefireplacemusthaveaminimumvertical
riseimmediatelyoffthefireplaceof24inches.Withthisconfiguration,thehorizontalruncan
be between a minimum of 13 inches and a maximum of 96 inches. FIGURE 2FIGURE 2
FIGURE 2FIGURE 2
FIGURE 2a-ca-c
a-ca-c
a-c..
..
. When
terminatingvertically,theverticalriseisaminimum36inchesandamaximum40feetfrom
the centre of the fireplace flue outlet. FIGURE 3.FIGURE 3.
FIGURE 3.FIGURE 3.
FIGURE 3.
Minimum clearance to combustible construction from fireplace to vent surfaces:
sides, back, bottom and top 0 inches
vent pipe 1 inch
recessed depth 13-3/4 inches
FIGURES2a-d
FIGURE3
VENTING
VENTING LENGTHS AND AIR TERMINAL LOCAVENTING LENGTHS AND AIR TERMINAL LOCA
VENTING LENGTHS AND AIR TERMINAL LOCAVENTING LENGTHS AND AIR TERMINAL LOCA
VENTING LENGTHS AND AIR TERMINAL LOCATIONSTIONS
TIONSTIONS
TIONS
Use only Napoleon or Simpson Dura-Vent Model DV-GS venting components. Minimum and maximum vent lengths, for
both horizontal and vertical installations, and air terminal locations for these installations, are set out in this manual and
must be adhered to. For Simpson Dura-Vent, follow the installation procedure provided with the venting components.
NOTE: BothWolf SteelandSimpsonDura-Vent requirethe 4 inch andthe7 inchdiametervent jointstobesealed.
Use the high temperature sealant provided.
When using Napoleon venting components, use only approved Napoleon rigid / flexible vent components with the
following termination kits: WALL TERMINAL KIT GD222,or 1/12 TO7/12PITCHROOFTERMINALKIT GD110, 8/12 TO12/
12 ROOF TERMINAL KIT GD111, FLAT ROOF TERMINAL KIT GD112 or PERISCOPE KIT GD201 (for wall penetration
below grade). With flexible venting, in conjunction with the various terminations, use either the 5 foot vent kit GD220 or the
10 foot vent kit GD330.
These vent kits allow for either horizontal or vertical venting of the fireplace. FIGURES 2, 3, & 4. The maximum number of
4" flexible connections is two horizontally or three vertically (excluding the fireplace and the air terminal connections).
For optimum flame appearance and fireplace performance, keep the vent length and number of elbows to a minimum.
The air terminal must remain unobstructed at all times. Examine the air terminal at least once a year to verify that it is
unobstructed and undamaged.

7
WS-415-112/06.18.99
FIGURE4
AIRAIR
AIRAIR
AIR TERMINTERMIN
TERMINTERMIN
TERMINAL INSTAL INST
AL INSTAL INST
AL INSTALLAALLA
ALLAALLA
ALLATIONS:TIONS:
TIONS:TIONS:
TIONS:
**
**
* Recommended to prevent condensation on windows and thermal breakage
****
****
** It is recommended to use a heat shield and to maximize the distance to vinyl clad soffits.
******
******
*** The periscope GD-201 requires a minimum 18 inches clearance from an inside corner.
********
********
**** This is a recommended distance. For additional requirements check local codes.
††
††
† Three feet above if within 10 feet horizontally.
‡‡
‡‡
‡ A vent shall not terminate directly above a sidewalk or paved driveway that is located between two single family
dwellings and serves both dwellings.
††††
††††
†† Permitted only if the veranda, porch, deck or balcony is fully open on a minimum of two sides beneath the floor.
†*†*
†*†*
†* Recommenced to prevent recirculation of exhaust products. For additional requirements check local codes.
A
B
C
D
E
F
G
H
I
J
K
L
M
N
O
12INCHES
9INCHES
12 INCHES*
18 INCHES**
12 INCHES**
0INCHES
2 INCHES***
0POUCES***
3FEET****
3FEET****
9INCHES
3FEET†
7FEET****
12INCHES****
16INCHES
2FEET†*
Clearanceabove grade,verandaporch, deckorbalcony.
Clearanceto windowsor doors that open.
Clearanceto permanentlyclosed windows.
Verticalclearancetoventilatedsoffitlocatedabovetheterminalwithin
a horizontal distance of 2 feet from the centerline of the terminal.
Clearanceto unventilatedsoffit.
Clearanceto anoutside cornerwall.
Clearance to an inside non-combustible corner wall or protruding
non-combustible obstructions (chimney, etc.).
Clearance to an inside combustible corner wall or protruding com-
bustible obstructions ( vent chase, etc.).
Clearanceto eachside ofthe centerlineextendedabove themeter
/ regulator assembly.
Clearanceto aservice regulatorvent outlet.
Clearance to a non-mechanical air supply inlet to the building or a
combustion air inlet to any other appliance.
Clearance to a mechanical air supply inlet.
Clearance above a paved sidewalk or paved driveway located on
public property unless fitted with a heat shield kit GD-301.
Clearanceunder averanda, porch,deck orbalcony.
Clearanceabovethe roof.
Clearancefrom anadjacent wall includingneighbouring buildings.
CANADIAN U.S.A.
12INCHES
12INCHES
12 INCHES*
18 INCHES**
12 INCHES**
0INCHES
0 INCHES***
0POUCES***
3FEET
6FEET
12INCHES
6FEET
7FEET‡
12INCHES††
16INCHES
2FEET†*
INSTALLATIONS

8
WS-415-112/06.18.99
FIGURE5
INSTALLATION
WALL AND CEILING PROTECTION
FORSAFEANDPROPEROPERATIONOFTHEFIREPLACE,FOLLOWTHEVENTINGINSTRUCTIONSEXACTLY.
HORIZONTAL INSTALLATION: This application occurs when venting through an
exterior wall. FIGURES 3a-c. Having determined the air terminal location, cut and frame
a hole in an exterior wall with a minimum square or round opening of 9½". (As an
alternative to framing, a vent pipe shield may be installed, ensuring a 1" clearance to
combustibles. See Figure 6.)
1. Mark and cut the vent pipe shield to the determined depth of the combustible wall.
Apply a bead of caulking (not supplied) to the framework or to the shield plate (in the
case of a finished wall) and secure the
shield through the opening to the inte-
rior wall. The final location of the vent
pipe shield should maintain the required
clearance to the 7" vent pipe / liner. Do
not fill this cavity with any type of mate-
rial. Apply a bead of caulking all around
and place a firestop spacer over the
vent shield to restrict cold air from be-
ing drawn into the room or around the fireplace. Ensure that both spacer
and shield maintain the required clearance to combustibles. Once the
vent pipe / liner is installed in its final
position, apply sealant between the
pipe / liner and the firestop spacer.
VERTICAL INSTALLATION: This application occurs when venting through a roof.
FIGURE 2. Installation kits for various roof pitches are available from your Napoleon
dealer. See Accessories to order the specific kit required.
1. Determine the air terminal location, cut and frame 9½ inch openings in the
ceiling and the roof to provide the minimum 1 inch clearance between the fireplace
pipe / liner and any combustible material. Try to center the exhaust pipe location
midway between two joist to prevent having to cut them. Use a plumb bob to line up
the center of the openings. DONOTFILLTHISSPACEWITHANYTYPEOFMATERIAL.
A vent pipe shield will prevent any materials such as insulation, from filling up the
1" air space around the pipe. FIGURE 9. Nail headers between the joist for extra
support.
2. Apply a bead of caulking (not supplied) to the framework or to the Wolf Steel
vent pipe shield plate or equivalent (in the case of a finished ceiling), and secure
over the opening in the ceiling. FIGURE 8. A firestop must be placed on the bottom
of each framed opening in a roof or ceiling that the venting system passes
through. FIGURE 9. Apply a bead of caulking all around and place a firestop spacer over the vent shield to restrict cold air
from being drawn into the room or around the fireplace. Ensure that both spacer and shield maintain the required
clearance to combustibles. Once the vent pipe / liner is installed in its final position, apply sealant between the pipe /
liner and the firestop spacer.
3. In the attic, after the pipe / liner has been installed, slide the vent pipe collar down to
cover up the open end of the shield and tighten. This will prevent any materials, such as
insulation, from filling up the 1" air space around the pipe.
FIGURE6
OR
FIGURE7
FIGURE8
FIGURE9
VENT PIPE
SHIELD
VENT
PIPE
COLLAR

9
WS-415-112/06.18.99
FIGURE11
FIGURE10
USING FLEXIBLE VENT COMPONENTS
FOR OPTIMUM PERFORMANCE IT IS RECOMMENDED THAT ALL HORIZONTAL RUNS HAVE A MINIMUM ¼ INCH RISE PER FOOT.
FOR SAFE AND PROPER OPERATION OF THE FIREPLACE, FOLLOW THE VENTING INSTRUCTIONS EXACTLY.
HORIZONTHORIZONT
HORIZONTHORIZONT
HORIZONTAL AIR TERMINAL INSTAL AIR TERMINAL INST
AL AIR TERMINAL INSTAL AIR TERMINAL INST
AL AIR TERMINAL INSTALLAALLA
ALLAALLA
ALLATIONTION
TIONTION
TION
1. Stretch the 4" diameter aluminum flexible liner
to the required length taking into account the ad-
ditional length needed for the finished wall sur-
face. Apply a heavy bead of the high temperature
sealant, supplied with the unit, to the inside of the
4" liner approximately 1" from the end. Slip the
liner a minimum of 2" over the fireplace vent collar
and secure with 3 #8 screws.
2. Using the 7" diameter flexible aluminum liner,
apply sealant, slide a minimum of 2 " over the fireplace
combustion air collar and secure with 3 #8 screws.
3. Insert the liners through the firestop. Position and secure
the fireplace using the nailing tabs (2 per side) and/or secure to the
floor using screws inserted through the two ¼" diameter holes in the front left and right corners of the base. The liners
should be flush with the exterior wall. The air terminal mounting plate may be recessed to a maximum of 3/4" into the
exterior wall or siding.
4. From outside, apply a bead of the high temperature sealant to the inside of both liners, approximately 1" from the
end of each liner.
5. Holding the air terminal (lettering in an upright, readable position), insert into both liners with a twisting motion to
ensure that both the terminal sleeves engage into the liners / sealant. Secure the terminal to the exterior wall and make
weather tight by sealing with caulking (not supplied).
EXTENDED HORIZONTEXTENDED HORIZONT
EXTENDED HORIZONTEXTENDED HORIZONT
EXTENDED HORIZONTAL AND CORNER AIRAL AND CORNER AIR
AL AND CORNER AIRAL AND CORNER AIR
AL AND CORNER AIR
TERMINAL INSTTERMINAL INST
TERMINAL INSTTERMINAL INST
TERMINAL INSTALLAALLA
ALLAALLA
ALLATIONTION
TIONTION
TION
A 45° corner installation must have 6 inch minimum rise between
the fireplace combustion air collar and the air terminal. FIGURE 2d.
In this case, vent lengths must be kept to a maximum of 36". For
longer vent lengths, a minimum vertical rise of 24" is re-
quired. FIGURE 2c. Use the GD220 vent kit and couplers for this
application.
1. Follow the instructions for "Horizontal Air Terminal Installa-
tions"., items 1 through 5.
Spacers are attached to the 4" inner flex liner at predeter-
mined intervals to maintain a 1-1/4" air gap to the 7" outer liner.
These spacers must not be removed.
2. The vent system must be supported approximately every 3 feet for both vertical and horizontal runs. Use Napoleon
support ring assemblies, GA-GD-010.370 or equivalent noncombustible strapping to maintain the minimum 1" clear-
ance to combustibles

10
WS-415-112/06.18.99
FIGURE14
FIGURE13
VERVER
VERVER
VERTICAL VENTING INSTTICAL VENTING INST
TICAL VENTING INSTTICAL VENTING INST
TICAL VENTING INSTALLAALLA
ALLAALLA
ALLATIONTION
TIONTION
TION
1. Fasten the roof support to the roof using the screws
provided. FIGURE 13. The roof support is optional. In this
case the venting is to be adequately supported using ei-
ther an alternate method suitable to the authority having
jurisdiction or the optional roof support.
2. Stretch the 4" diameter aluminum flexible liner to the
required length. Slip the liner a minimum of 2" over the inner sleeve of the air terminal and
secure with 3 #8 screws. Seal using a heavy bead of the high temperature sealant.
3. Repeat using 7" diameter aluminum flexible liner. FIGURE 12.
4. Thread the air terminal pipe assembly down through the roof. The air terminal must be
located vertically and plumb. Attach the air terminal assembly to the roof support, ensuring that
a minimum 16" of air terminal will penetrate the roof when fastened.
DONOTCLAMPTHEFLEXIBLE ALUMINUMLINER.
5. Remove nails from the shingles, above and to the sides of the chimney. Place the flashing over the air terminal and
slide it underneath the sides and upper edge of the shingles. Ensure that the air terminal is properly centered within the
flashing, giving a 3/4" margin all around. Fasten to the roof. Do not nail through
the lower portion of the flashing. Make weather-tight by sealing with caulking.
Where possible, cover the sides and top edges of the flashing with roofing mate-
rial.
6. Apply a heavy bead of weatherproof caulking 2 inches above the flashing.
Slide the storm collar around the air terminal and down to the caulking. Tighten to
ensure that a weather-tight seal between the air terminal and the collar is achieved.
Attach the other storm collar centered between the air intake and the air exhaust
slots onto the air terminal. Tighten securely. FIGURE 14. Attach the vertical rain
cap.
Spacers are attached to the 4" inner flex liner at predetermined intervals to
maintain a 1-1/4" air gap to the 7" outer liner. These spacers must not be removed.
7. If more liner needs to be used to reach the fireplace, follow the same procedure as found in EXTENDED HORIZON-
TAL AND CORNER AIR TERMINAL INSTALLATION. The vent system must be supported approximately every 3 feet for
both vertical and horizontal runs. Use Wolf Steel support ring assembly GA-GD-010.370 or equivalent noncombustible
strapping to maintain a clearance to combustibles of 1".
FIGURE12

11
WS-415-112/06.18.99
INSTALLATION
USING RIGID VENT COMPONENTS
FOR SAFE AND PROPER OPERATION OF THE FIREPLACE, FOLLOW THE VENTING
INSTRUCTIONSEXACTLY.
FOR OPTIMUM PERFORMANCE, IT IS RECOMMENDED THAT ALL HORIZONTAL RUNS
HAVE A MINIMUM ¼ INCH RISE PER FOOT.
The vent system must be supported approximately every 3 feet for both vertical and horizontal runs. Use Napoleon vent
spacers WS-615-33 or equivalent every 3 feet and either side of each elbow to maintain the minimum 1¼" clearance
between the outer and inner vent pipes. Use Napoleon support ring assembly GA-GD-010.370 or equivalent noncom-
bustible strapping to maintain the minimum 1" clearance to combustibles for both vertical and horizontal runs.
HORIZONTHORIZONT
HORIZONTHORIZONT
HORIZONTAL AIR TERMINAL INSTAL AIR TERMINAL INST
AL AIR TERMINAL INSTAL AIR TERMINAL INST
AL AIR TERMINAL INSTALLAALLA
ALLAALLA
ALLATIONTION
TIONTION
TION
1. Move the fireplace into position. Measure the vent
length required between terminal and fireplace taking
into account the additional length needed for the fin-
ished wall surface and any 1¼" overlaps between vent-
ing components.
2. Apply high temperature sealant to the outer edge
of the 4" inner collar of the fireplace. Attach the first vent
component and secure using 3 self tapping screws. Re-
peat using 7" piping.
3. Holding the air terminal (lettering in an upright, readable po-
sition), insert into both vent pipes with a twisting motion to ensure
that both the terminal sleeves engage into the vent pipes and the sealant. Secure the terminal to the exterior wall and
make weather tight by sealing with caulking (not supplied). The air terminal mounting plate may be recessed to a
maximum of 3/4" into the exterior wall or siding.
EXTENDED HORIZONTEXTENDED HORIZONT
EXTENDED HORIZONTEXTENDED HORIZONT
EXTENDED HORIZONTAL AND CORNER AIR TERMINAL INSTAL AND CORNER AIR TERMINAL INST
AL AND CORNER AIR TERMINAL INSTAL AND CORNER AIR TERMINAL INST
AL AND CORNER AIR TERMINAL INSTALLAALLA
ALLAALLA
ALLATIONTION
TIONTION
TION
A 45° corner installation can have 0 inch rise between the fireplace combustion air
collar and the air terminal. In this case, vent lengths must be kept to a maximum of
36". For longer vent lengths, a minimum vertical rise of 24" is required. FIGURE 2c.
1. Follow the instructions for "Horizontal Air Terminal Installations", items 1 to 2.
2. Continue adding components alternating inner and outer venting. Ensure that
all 4" venting and elbows have sufficient vent spacers attached and each compo-
nent is securely fastened to the one prior. Attach the 4" telescopic sleeve to the vent
run. Repeat using a 7" telescopic sleeve. Secure and seal as before. To facilitate
completion, attach 4" and 7" couplers to the air terminal.
3.Install the air terminal. See item 3 above. Extend the 4" telescopic sleeve;
connect to the air terminal assembly. Fasten with self tapping screws and seal.
Repeat using the 7" telescopic sleeve.
FIGURE15
TELESCOPIC SLEEVE
VENTING
20"
COUPLER
AIR TERMINAL
FIGURE16

12
WS-415-112/06.18.99
Elbowsand rigid36" lengthsare manufacturedwith the4" componentsper-
manentlyfixed withinthe 7"components. Applyhigh temperaturesealantto
both collars and install the assembly as a single unit securing the outer 7"
piecewith threescrews.
VERVER
VERVER
VERTICAL VENTING INSTTICAL VENTING INST
TICAL VENTING INSTTICAL VENTING INST
TICAL VENTING INSTALLAALLA
ALLAALLA
ALLATIONTION
TIONTION
TION
1. Move the fireplace into position.
2. Fasten the roof support to the roof using the screws provided. The roof support is optional. In this case the venting
is to be adequately supported using either an alternate method suitable to the authority having jurisdiction or the
optional roof support.
3. Apply high temperature sealant to the outer edge of the inner sleeve of the air terminal. Slip a 4" diameter coupler
a minimum of 2" over the sleeve and secure using 3 screws.
4.Apply high temperature sealant to the outer edge of the of the outside sleeve of the air terminal. Slip a 7" diameter
coupler over the sleeve and secure as before. Trim the 7" coupler even with the 4" coupler end.
5.Thread the air terminal pipe assembly down through the roof support and attach, ensuring
that a minimum 16" of air terminal will penetrate the roof when fastened. If the attic space is
tight, we recommend threading the Wolf Steel vent pipe collar or equivalent loosely onto the
air terminal assembly as it is passed through the attic. FIGURE 19. The air terminal must be
located vertically and plumb.
6.Remove nails from the shingles, above and to the sides of the chimney. Place the flashing
over the air terminal and slide it underneath the sides and upper edge of the shingles. Ensure
that the air terminal is properly centered within the flashing, giving a 3/4" margin all around.
Fasten to the roof. Do NOT nail through the lower portion of the flashing. Make weather-tight by
sealing with caulking. Where possible, cover the sides and top edges of the flashing with
roofing material.
7. Apply a heavy bead of waterproof caulking 2 inches above the flashing. Slide the storm collar around the air terminal
and down to the caulking. Tighten to ensure that a weather-tight seal between
the air terminal and the collar is achieved. Attach the other storm collar centered
between the air intake and air exhaust slots onto the air terminal. Tighten se-
curely. Attach the rain cap.
8. Continue adding rigid venting sections, sealing and securing as above.
Attach a 4" collapsed telescopic pipe to the last section of rigid piping. Secure
with screws and seal. Repeat using a 7" telescopic pipe.
9. Run a bead of high temperature sealant around the outside of the 4" elbow.
Pull the adjustable pipe a minimum 2" onto the elbow. Secure with 3 screws.
Repeat with the 7" telescopic pipe.
10. In the attic, slide the vent pipe collar down to cover up the open end of the shield and tighten. This will prevent any
materials, such as insulation, from filling up the 1" air space around the pipe.
FIGURE17
FIGURE19
FIGURE18

13
WS-415-112/06.18.99
MOBILE HOME INSTMOBILE HOME INST
MOBILE HOME INSTMOBILE HOME INST
MOBILE HOME INSTALLAALLA
ALLAALLA
ALLATIONTION
TIONTION
TION
In Canada, mobile home installation may be vented horizontally or vertically. In the United States, it may only be installed
vertically. See "Vertical Venting" or "Horizontal Air Terminal Installation" for installation.
The fireplace is equipped with two 1/4" diameter holes located in the front left and right corners of the base. For mobile
home installations, the fireplace must be fastened in place. Use #10 hex head screws, inserted through the holes in the
base to secure. It is recommended that the fireplace be secured in all installations.
GAS INSTGAS INST
GAS INSTGAS INST
GAS INSTALLAALLA
ALLAALLA
ALLATIONTION
TIONTION
TION
Proceed once the vent installation is complete.
1. Route a 3/8" N.P.T. black iron gas line, 1/2" type-L copper tubing or equivalent to the fireplace.
2. For ease of accessibility, an optional remote wall switch or millivolt thermostat may be installed in a convenient
location. Route 2-strand (solid core) millivolt wire through the electrical hole located at the bottom left side of the unit.
The recommended maximum lead length depends on wire size:WIRESIZE MAX.LENGTH
14gauge 100 feet
16gauge 60 feet
18gauge 40 feet
Attach the two leads to terminals 1 and 3 located on the gas valve. FIGURE 20.
3. Install rigid black pipe, 1/2" type-L copper tubing or, if local codes permit, a 3/8" flex connector and shutoff valve to
the gas line and the fireplace gas valve. Seal and tighten securely. An adapter fitting is required between the gas valve
and the copper tubing or flex connector.
DONOTKINKFLEXCONNECTOR.FIGURE21.
4. Check for gas leaks by brushing on a soap and water solution.
DONOTUSEOPENFLAME.
PURGEALLGASLINESWITH THEGLASSDOOROFTHEFIREPLACEREMOVED.ASSURETHATACONTINUOUSGAS
FLOWIS ATTHE BURNERBEFORE RE-INSTALLINGTHEDOOR.
P
I
P
I
3
1
2
L
O
T
N
O
L
O
T
H
I
L
O
F
F
O
FIGURE20
FIGURE21
DONOTCONNECTEITHER THE WALL SWITCH,THERMO-
STAT ORGASVALVE TOELECTRICITY(110 VOLTS).
ALWAYS TURN OFF THE PILOT AND THE FUEL SUPPLY AT THE SOURCE, PRIOR TO MOVING THE
MOBILE HOME.
AFTER MOVING THE MOBILE HOME AND PRIOR TO LIGHTING THE FIREPLACE, ENSURE THAT
THE LOGS ARE POSITIONED CORRECTLY.

14
WS-415-112/06.18.99
FRAMINGFRAMING
FRAMINGFRAMING
FRAMING
It is best to frame your fireplace after it is positioned and the vent system is installed. Use 2x4's and frame to local
building codes. FIGURE 22-24.
To install the fireplace face flush with the finished wall, position the framework to accomodate the thickness of the
finished wall. For corner installation, allow a minimum rise of 6 inches between the fireplace and the air terminal using
Napoleon flexible venting components / 0 inch rise when using Napoleon rigid venting or Simpson Dura-vent compo-
nents. FIGURE 2d. Pull out the four nailing tabs, attached on either side of the fireplace and secure to the 2x4 framing to
facilitate drywall installation and/or secure the fireplace to the floor using #10 screws (not supplied) using the two ¼" diameter
holes in the front left and right corners of the base.
Combustible materials must be installed flush with the front of the fireplace but must not cover any of the black face-area
of the fireplace. Non-combustible material (brick, stone or ceramic tile) may protrude.
It is not necessary to install a hearth extension with this fireplace system. Objects placed in front of the fireplace should
be kept a minimum of 24" away from the front face.
Mantle clearance can vary according to the mantle depth. FIGURES 25. Use the graph to help evaluate the clearance
needed.
FIGURE22
FIGURES25
FIGURE23
FIGURES24
OUTSIDE
CHASE
INSIDE
CHASE

15
WS-415-112/06.18.99
FINISHING
DOOR, LOUVRE AND TRIM REMOVDOOR, LOUVRE AND TRIM REMOV
DOOR, LOUVRE AND TRIM REMOVDOOR, LOUVRE AND TRIM REMOV
DOOR, LOUVRE AND TRIM REMOVAL & INSTAL & INST
AL & INSTAL & INST
AL & INSTALLAALLA
ALLAALLA
ALLATIONTION
TIONTION
TION
ENSURETHATTHEDOORISPROPERLYCLIPPEDONTOTHESTEELLIPTOPREVENT
OVERHEATING,GLASSBREAKAGEAND/ORDISCOLOURATIONOFTHEUPPERTRIM.
Both top and bottom door trim must be removed prior to
door removal. Lift up the top trim and unhook from the door.
The bottom trim, held on with magnets, may be pulled off
and lifted out of the bottom door sill. FIGURE 29.
Remove the five screws securing the sides and bottom of the door. Lift up and out. To re-install, repeat in reverse order.
Retighten screws snugly. DO NOT OVER-TIGHTEN.
The top and bottom door trim may be installed next. Lift up the top trim and hook over the top of the door. The bottom trim
is inserted into the bottom door sill. Push in to engage the magnets. The louvre assemblies are installed as illustrated
in FIGURE 29. Optional plated door trim, door side trim and arched door facias are available at your local Napoleon / Wolf
Steel dealer.
LOG PLACEMENTLOG PLACEMENT
LOG PLACEMENTLOG PLACEMENT
LOG PLACEMENT
PHAZERTM logs exclusive to Napo-
leon Fireplaces, provide a unique and
realistic glowing effect that is different
in every installation.
POSITIONINGTHELOGS IMPROP-
ERLYWILLCAUSEFLAMEIMPINGE-
MENTANDCARBONING.
Position the logs as shown.
Place the back log onto the log sup-
port bracket, located on the rear wall
of the combustion chamber, pushing
it as close to the firebox wall as pos-
sible.
Center the front log behind the two lo-
cating tabs and along the inside front
edge of the burner tray.
Set the two smaller logs into the pockets and grooves of the front and back logs, respectively.
Log colours may vary. During the initial use of the fireplace, the colours will become more uniform as colour pigments
burn in during the heat activated curing process. Blocked burner ports can cause an incorrect flame pattern, carbon
deposits and delayed ignition. PHAZERTM logs glow when exposed to direct flame. Use only certified PHAZERTM logs
available from your Napoleon / Wolf Steel Ltd. dealer.
FIGURES28
FIGURE27
FIGURE29b
FIGURE29c
FIGURE29a
DOOR
STEEL LIP
FIGURE26

16
WS-415-112/06.18.99
OPTIONAL BLOWER INSTALLATION
INSTALLATION TO BE DONE BY A QUALIFIED INSTALLER and must be
electrically connected and grounded in accordance with local codes. In the
absence of local codes, use the current CSA C22.1 CANADIAN ELECTRICAL CODE in
CanadaortheANSI/NFPA 70-1996 NATIONAL ELECTRICAL CODE intheUnitedStates
If the fireplace was not previously equipped with a blower: route a
grounded 2-wire, 60hz power cable to the receptacle / junction box. At this point, it
must be strain relieved and insulated.
The three slots on the blower mounting
bracket allow ease of adjustment when
attaching the blower. For a quiet running
blower, do not allow the assembly to sit
on the firebox base.
Slide the vibration reducing pad (A) into the clip (C) and up against the threaded
stud (B) at the other end. The blower must be able to be positioned entirely
onto the pad.
Tilt the blower onto its side. Slide it past the controls
and into the clip (C). Secure to the threaded stud using
the lock washer and wing nut provided. Ensure that the
blower does not touch the fireplace base or the firebox.
Attach the connectors from the black and white wires to
the thermodisc and secure the thermodisc bracket to
the securing stud at the bottom left of the unit using a
lock washer and wing nut. Ensure that the thermodisc
touches the firebox wall.
Attach the connectors from the black and red wires to
the blower.
Attach and secure the variable speed switch using the nut provided. Plug the harness
cord into the receptacle.
The wire harness provided in this kit is a universal harness. When installed, ensure that any excess
wire is contained, preventing it from making contact with moving or hot objects.
Because the blower is thermally activated, when turned on, it will automatically start approximately 10
minutes after lighting the fireplace and will run for approximately 30-45 minutes after the fireplace has
been turned off. Use of the fan increases the output of heat.
red
white
black
FIGURE30
FIGURE35
RECEPTACLE /
THERMODISC
GROUND
SCREW
JUNCTION BOX
FIGURE34
C
C
FIGURE31
SLOTS
ELONGATED
FIGURE33
FIGURE32
A
B
C

17
WS-415-112/06.18.99
OPTIONAL FAN INSTALLATION
ELECTRICAL INSTALLATION TO BE DONE BY A QUALIFIED INSTALLER and must be connected and grounded in
accordance with local codes. In the absence of local codes, use the current CSA C22.1 CANADIAN ELECTRICAL CODE in
Canada or the ANSI/NFPA 70-1990 NATIONAL ELECTRICAL CODE in the United States.
If the fireplace was not previously equipped with a fan: route a grounded 2-wire, 60hz power cable to the junction box.
At this point, it must be strain relieved and insulated.
The wire harness provided in this kit is a
universal harness. When installed, ensure
that any excess wire is contained, prevent-
ing it from making contact with moving or
hot objects.
Position the vibration reducing pad into the
clip and onto the threaded stud at the other
end, piercing a hole into the pad. The fan
assembly must be able to be positioned entirely onto the pad.
Slide the fan assembly past the controls and and into the clip.
Secure using the lock washer and nut provided.
Attach the connectors from the black and white wires to the
thermodisc and secure the thermodisc bracket to the securing
stud at the bottom left of the unit using a lock washer and wing nut.
Ensure that the thermodisc touches the firebox wall.
GD36THERMOSTATICSENSORCONTROL
This optional kit is meant to be used only in conjunction with the GD65 Fan
Kit, shown above, which may be ordered from your Wolf Steel / Napoleon
dealer.
With the thermostatic sensor option, the fan, when turned on, becomes
thermally activated, and will automatically run approximately 15-30 minutes
after the fireplace has been lit and for approximately 30-45 minutes after the
fireplace has been turned off.
Use of the fan increases the output of heat.
Unplug the power cord from the receptacle. Connect all wires as shown.
Attach and secure the sensor assembly bracket to the securing stud located
next to the receptacle/junction box at the bottom left of the unit using the lock
washer and wing nut. Ensure that the
thermodisc touches the firebox wall.
Plug the power cord back into the re-
ceptacle.
Wheninstalled, ensure that any excess
wire is contained, preventing it from
making contact with moving or hot ob-
jects.
RECEPTACLE /
JUNCTION BOX
SLOTS
OPEN ENDED
BRACKET
VARIABLE SPEED/
PIEZO IGNITOR
JUNCTION BOX
THERMODISC
SENSOR ASSEMBLY
BRACKET
RECEPTACLE /
FIGURE36
FIGURE38
FIGURE39
FIGURE37

18
WS-415-112/06.18.99
OPERATION / MAINTENANCE
OPERAOPERA
OPERAOPERA
OPERATING INSTRUCTIONSTING INSTRUCTIONS
TING INSTRUCTIONSTING INSTRUCTIONS
TING INSTRUCTIONS
Whenlit forthe first time,the fireplacewillemit aslight odourfora fewhours. Thisisa normaltemporary condition
caused by the curing of the logs and the "burn-in" of internal paints and lubricants used in the manufacturing
processand willnot occuragain. Afterextended periodsofnon-operation suchas followinga vacationor awarm
weatherseason, thefireplace mayemit aslight odourfor afew hours.This iscaused by dustparticles inthe heat
exchangerburning off. In both cases,open awindow tosufficiently ventilatethe room.
PURGE ALL GAS LINES WITH THE GLASS DOOR OF THE FIREPLACE REMOVED. ASSURE THAT A
CONTINUOUS GAS FLOW IS AT THE BURNER BEFORE INSTALLING THE DOOR.
FORYOURSAFETYREADBEFORELIGHTING:
A. This fireplace is equipped with a pilot which must be lit by hand while following these instructions exactly.
B. Before operating smell all around the fireplace area for gas and next to the floor because some gas is heavier than
air and will settle on the floor.
WHATTO DOIFYOU SMELLGAS:
• Turn off all gas to the fireplace.
• Open windows.
• Do not try to light any appliance.
• Do not touch any electric switch; do not use any phone in your building.
• Immediately call your gas supplier from a neighbour's phone. Follow the gas supplier's instructions.
• If you cannot reach your gas supplier, call the fire department.
C. Use only your hand to turn the gas control knob. Never use tools. If the knob will not turn by hand, do not try to repair
it. Call a qualified service technician. Force or attempted repair may result in a fire or explosion.
D. Do not use this fireplace if any part has been under water. Immediately call a qualified service technician to inspect
the fireplace and replace any part of the control system and any gas control which has been under water.
P
I
N
O
L
O
T
F
F
O
GAS KNOB
LIGHTINGINSTRUCTIONS
WARNING: The gas valve has an interlock device which will not allow the pilot burner to be lit until the thermocouple has
cooled. Allow approximately 60 seconds for the thermocouple to cool.
When lighting and re-lighting, the gas knob cannot be turned from pilot to off unless the knob is depressed slightly.
1. Stop! Read the above safety information on this label.
2. Turn off all electric power to the fireplace.
3. Turn the gas knob clockwise to off.
4. Wait five (5) minutes to clear out any gas. If you smell gas includ-
ing near the floor. Stop! Follow "B" in the above safety information on
this label. If you don't smell gas go the next step.
5. Turn gas knob counter-clockwise to pilot.
6. Depress slightly and hold gas knob while lighting the pilot with
the push button ignitor. Keep knob depressed for one minute, then
release. If pilot does not continue to burn, repeat steps 3 through 5.
TOTURNOFFGAS
1. Turn off all electric power to the fireplace if service is to be performed.
2. Push in gas control knob slightly and turn clockwise to off. Do not force.
7. With pilot lit, depress and turn gas knob
counter-clock-wise to on.
8. If equipped with remote on-off switch/ther-
mostat, main burner may not come on when
you turn valve to on. Remote switch must be
in the on position to ignite burner.
9. Turn on all electric power to the fireplace.
FLAME
ADJUSTMENT
KNOB
O
T
P
I
L
L
O
I
H
T
P
I
L
O
N
O
F
F
O
PILOT
ON/OFF
KNOB

19
WS-415-112/06.18.99
ADJUSTMENTS
PILOT BURNER ADJUSTMENTPILOT BURNER ADJUSTMENT
PILOT BURNER ADJUSTMENTPILOT BURNER ADJUSTMENT
PILOT BURNER ADJUSTMENT
Adjust the pilot screw to provide properly sized flame.
Turn in a clockwise direction to reduce the gas flow.
FIGURES 40 & 41.
VENTURI ADJUSTMENTVENTURI ADJUSTMENT
VENTURI ADJUSTMENTVENTURI ADJUSTMENT
VENTURI ADJUSTMENT
Natural gas models have air shutters set at 1/8 (.125) inch open. Propane gas
models have air shutters set at 1/4 (.250) inch open. Closing the air shutter will
cause a more yellow flame, but can lead to carboning. Opening the air shutter
will cause a more blue flame, but can cause flame lifting from the burner ports.
The flame may not appear yellow immediately; allow 15 to 30 minutes for the
final flame colour to be established. FIGURE 42.
AIRSHUTTERADJUSTMENTMUSTONLYBE DONEBY AQUALIFIED GASINSTALLER!
MAINTENANCEMAINTENANCE
MAINTENANCEMAINTENANCE
MAINTENANCE TURN OFF THE GAS AND ELECTRICAL POWER BEFORE SERVICING THE FIREPLACE.
CAUTION: Label all wires prior to disconnection when servicing controls. Wiring errors can cause improper and danger-
ous operation. Verify proper operation after servicing. This fireplace and its venting system should be inspected before
use and at least annually by a qualified service person. The fireplace area must be kept clear and free of combustible
materials, gasoline or other flammable vapours and liquids. The flow of combustion and ventilation air must not be
obstructed.
1. In order to properly clean the burner and pilot assembly, remove the logs to expose both assemblies.
2. Keep the control compartment, logs, burner, air shutter opening and the area surrounding the logs clean by vacuum-
ing or brushing, at least once a year.
3. Check to see that all burner ports are burning. Clean out any of the ports which may not be burning or are not burning
properly.
4. Check to see that the pilot flame is large enough to engulf the thermocouple and thermopile and reaches toward the
burner with the third jet.
5. Replace the cleaned logs.
6. Check to see that the main burner ignites completely on all openings when the gas knob for the burner is turned on.
A 5 to 10 second total light-up period is satisfactory. If ignition takes longer, consult your Napoleon dealer / distributor.
7. Check that the gasketing on the sides, top and bottom of the door is not broken or missing. Replace if necessary.
FLAME MUST ENVELOP
UPPER 3/8" TO 1/2" OF
THERMOCOUPLE &
THERMOPILE
PILOT
THERMOPILE BURNER
ELECTRODE
THERMO-
COUPLE
FIGURE41
P
I
P
I
PILOT SCREW
L
O
T
N
O
L
O
T
H
I
L
O
F
F
O
FIGURE40
FIGURE42

20
WS-415-112/06.18.99
REPLACEMENTS
ORDERING REPLACEMENT PORDERING REPLACEMENT P
ORDERING REPLACEMENT PORDERING REPLACEMENT P
ORDERING REPLACEMENT PARAR
ARAR
ARTSTS
TSTS
TS
Contact your dealer or the factory for questions concerning prices and policies on replacement parts. Normally all parts
can be ordered through your Napoleon dealer or distributor. When ordering replacement parts always give the following
information:
1. MODEL &SERIAL NUMBER OF FIREPLACE 3. PART NUMBER 5. FINISH
2. INSTALLATION DATE OF FIREPLACE 4. DESCRIPTION OF PART
REPLACEMENT PREPLACEMENT P
REPLACEMENT PREPLACEMENT P
REPLACEMENT PARAR
ARAR
ARTSTS
TSTS
TS FOR WARRANTY PARTS, APHOTOCOPY OF THE ORIGINAL INVOICE WILL BE REQUIRED TO HONOUR THE CLAIM.
PART NO.PART NO.
PART NO.PART NO.
PART NO. DESCRIPTIONDESCRIPTION
DESCRIPTIONDESCRIPTION
DESCRIPTION
WS-300-20 GLASS ONLY
GD-010.402 GLASSc/w GASKET
GD-321-K BLACK DOOR C/W GLASS
GD-562.09 DOOR GASKET (100 INCHES)
GD-020.042 PKG OF 5 DOOR SCREWS
WS-455-048 #47 NATURAL GAS ORIFICE
WS-455-047 #56 PROPANE GAS ORIFICE
WS-357-01 PIEZO IGNITER
WS-680-04 THERMOPILE
WS-680-05 THERMOCOUPLE
WS-100-38 NATURAL GAS PILOT ASSEMBLY
WS-100-39 PROPANE GAS PILOT ASSEMBLY
GD-715.136 TOP DOOR TRIM
GD-010.376 BOTTOM DOOR TRIM
GD-715.11 POLISHED BRASS UPPER LOUVRE
GD-010.391 POLISHED BRASS LOWER LOUVRE ASSEMBLY
WS-573-008 HIGH TEMPERATURE SEALANT
GD-135.028 FRONT LOG
GD-135.057 REAR LOG
GD-135.040 RIGHT LOG
GD-135.039 LEFT LOG
GL-619 LOG SET ASSEMBLY
GD-215.032 COMBUSTION AIR DEFLECTOR
WS-660-5 ON/OFF TOGGLE SWITCH
WS-100-053 BURNER
WS-455-23 #51 NATURAL GAS PILOT ORIFICE
WS-455-24 #30 PROPANE GAS PILOT ORIFICE
WS-725-25 NATURAL GAS VALVE
WS-725-26 PROPANE GAS VALVE
WS-750-09 IGNITER WIRE
WS385-33 NAPOLEONLOGO
WS-430-001 CERAMIC MAGNET
GD660 STANDARD WALL SWITCH & 20FT OF WIRE
FLEXIBLE VENT KITSFLEXIBLE VENT KITS
FLEXIBLE VENT KITSFLEXIBLE VENT KITS
FLEXIBLE VENT KITS
PART NO.PART NO.
PART NO.PART NO.
PART NO. DESCRIPTIONDESCRIPTION
DESCRIPTIONDESCRIPTION
DESCRIPTION PART NO.PART NO.
PART NO.PART NO.
PART NO. DESCRIPTIONDESCRIPTION
DESCRIPTIONDESCRIPTION
DESCRIPTION
GD-010.397 4" FLEX ALUMINUM LINER-(5 FT) C/WSPACERS GS10.300 4" FLEX ALUMINUM LINER - (10 FT) C/WSPACERS
WS-410-17 7" FLEX ALUMINUM LINER -(5 FT) WS-410-018 7" FLEX ALUMINUM LINER -(10 FT)
GD10.370 WALL SUPPORT ASSEMBLY
TERMINAL KITSTERMINAL KITS
TERMINAL KITSTERMINAL KITS
TERMINAL KITS
ROOF TERMINAL KITS:ROOF TERMINAL KITS:
ROOF TERMINAL KITS:ROOF TERMINAL KITS:
ROOF TERMINAL KITS: 1/12 TO 7/12 PITCH1/12 TO 7/12 PITCH
1/12 TO 7/12 PITCH1/12 TO 7/12 PITCH
1/12 TO 7/12 PITCH --
--
-GD110GD110
GD110GD110
GD110
8/12 TO 12/12 PITCH8/12 TO 12/12 PITCH
8/12 TO 12/12 PITCH8/12 TO 12/12 PITCH
8/12 TO 12/12 PITCH --
--
-GD111GD111
GD111GD111
GD111
FLAFLA
FLAFLA
FLAT ROOFT ROOF
T ROOFT ROOF
T ROOF --
--
-GD112GD112
GD112GD112
GD112
PART NO.PART NO.
PART NO.PART NO.
PART NO. DESCRIPTIONDESCRIPTION
DESCRIPTIONDESCRIPTION
DESCRIPTION
GD10.569 AIR TERMINAL
GD-120.036 VERTICAL CAP
WS-170-063 STORMCOLLAR
GA-GD-010.567 ROOF SUPPORT
WS-263-054 /WS-263-055 /WS-263-056 ROOF FLASHING
PERISCOPEPERISCOPE
PERISCOPEPERISCOPE
PERISCOPE - GD201- GD201
- GD201- GD201
- GD201
WALL TERMINAL KITWALL TERMINAL KIT
WALL TERMINAL KITWALL TERMINAL KIT
WALL TERMINAL KIT - GD222- GD222
- GD222- GD222
- GD222
GL-619
I
N
T
O
GD220GD220
GD220GD220
GD220
(5 FT)(5 FT)
(5 FT)(5 FT)
(5 FT) GD330GD330
GD330GD330
GD330
(10 FT)(10 FT)
(10 FT)(10 FT)
(10 FT)