Napoleon IR3N-1 User manual

EN
W415-1198 / 05.24.13
FR
PG
33
$10.00
INSTALLER: LEAVE THIS MANUAL WITH THE APPLIANCE.
CONSUMER: RETAIN THIS MANUAL FOR FUTURE REFERENCE.
NEVER LEAVE CHILDREN OR OTHER AT RISK INDIVIDUALS ALONE WITH THE APPLIANCE.
INSTALLATION AND
OPERATING INSTRUCTIONS
Wolf Steel Ltd., 24 Napoleon Rd., Barrie, ON, L4M 0G8 Canada /
103 Miller Drive, Crittenden, Kentucky, USA, 41030
Phone [phone] • Fax [phone] • www.napoleonfireplaces.com • [email protected]
1.36C
CERTIFIED FOR CANADAAND UNITED STATES USING ANSI/CSAMETHODS.
SAFETY INFORMATION
!WARNING
- Do not store or use gasoline or other flammable
vapors and liquids in the vicinity of this or any
other appliance.
- WHAT TO DO IF YOU SMELL GAS:
• Do not try to light any appliance.
• Do not touch any electrical switch; do not use
any phone in your building.
• Immediately call your gas supplier from a
neighbour’s phone. Follow the gas supplier’s
instructions.
• If you cannot reach your gas supplier, call the
fire department.
- Installation and service must be performed by a
qualified installer, service agency or the supplier.
This appliance may be installed in an aftermarket,
permanently located, manufactured home (USA
only) or mobile home, where not prohibited by
local codes.
This appliance is only for use with the type of gas
indicated on the rating plate. This appliance is
not convertible for use with other gases, unless a
certified kit is used.
If the information in these instructions
are not followed exactly, a fire or
explosion may result causing property
damage, personal injury or loss of life.
HOT GLASS WILL CAUSE
BURNS.
DO NOT TOUCH GLASS UNTIL
COOLED.
NEVER ALLOW CHILDREN TO
TOUCH GLASS.
!
WARNING
CERTIFIED
Decorative Product: Not for use as a heating appliance.
CERTIFIED UNDER CANADIANAND AMERICAN NATIONAL STANDARDS: CSA 2.22, ANSI Z21.50 FOR VENTED GAS FIREPLACES.
IR3N-1
NATURAL GAS
IR3P-1
PROPANE

TABLE OF CONTENTS
1.0 INSTALLATION OVERVIEW 3
2.0 INTRODUCTION 4
2.1 DIMENSIONS 5
2.2 MINIMUM CLEARANCE TO COMBUSTIBLES 5
2.3 GENERAL INSTRUCTIONS 5
2.4 GENERAL INFORMATION 6
2.5 RATING PLATE INFORMATION 7
3.0 INSTALLATION 8
3.1 LEVELLING THE APPLIANCE 8
3.2 CHIMNEY CONNECTION 9
3.3 GAS INSTALLATION 10
4.0 FINISHING 10
4.1 MINIMUM MANTEL CLEARANCES 11
4.2 DOOR REMOVALAND INSTALLATION 11
4.3 LOG PLACEMENT 12
4.4 OPTIONAL ROCK PLACEMENT 13
4.5 GLOWING EMBERS 13
4.6 LOGO PLACEMENT 13
4.7 BATTERY INSTALLATION 13
5.0 ELECTRICAL INFORMATION 14
5.1 WIRING DIAGRAM 14
6.0 OPERATION 15
6.1 OPERATING AND LIGHTING INSTRUCTIONS 15
6.2 OPERATION 16
6.2.1 GENERAL REMOTE TRANSMITTER LAYOUT 16
6.2.2 PROGRAMMING 16
6.2.3 TURNING "ON" THE APPLIANCE 17
6.2.4 TURNING "OFF" THE APPLIANCE 17
6.2.5 HAND HELD REMOTE TRANSMITTER OPERATIONS 17
6.2.6 TEMPERATURE DISPLAY 18
6.2.7 SETTING THE TIME 18
6.2.8 SETTING THE TIMER FUNCTION 18
6.2.9 FLAME HEIGHT 18
6.2.10 LOW BATTERY 19
7.0 ADJUSTMENTS 19
7.1 PILOT BURNER ADJUSTMENT 19
7.2 VENTURI ADJUSTMENT 19
7.3 FLAME CHARACTERISTICS 20
7.4 LP CONVERSION 20
8.0 MAINTENANCE 21
8.1 ANNUAL MAINTENANCE 21
8.2 CARE OF GLASS 22
8.3 CARE OF PLATED PARTS 22
8.4 DOOR GLASS REPLACEMENT 22
8.5 BURNER REMOVAL 23
8.6 VALVE TRAIN REPLACEMENT 23
9.0 REPLACEMENTS 24
10.0 TROUBLESHOOTING 27
11.0 WARRANTY 30
12.0 SERVICE HISTORY 31
W415-1198 /05.24.13
2
EN
NOTE: changes, other than editorial, are denoted by a vertical line in the margin.

W415-1198 / 05.24.13
3
EN
Venting, see “INSTALLATION
- CHIMNEY CONNECTION”
section.
Rating Plate, see “RATING
PLATE INFORMATION”
section.
Logs, see “FINISHING - LOG
PLACEMENT” section.
Batteries, see “BATTERY INSTALLATION” section.
Receiver, see “PROGRAMMING” section.
“ON/OFF” switch, see “TURNING ON THE
APPLIANCE” section.
1.0 INSTALLATION OVERVIEW

W415-1198 /05.24.13
4
EN
2.0 INTRODUCTION
3.2B
!
WARNING
• THIS APPLIANCE IS HOT WHEN OPERATED AND CAN CAUSE SEVERE BURNS IF CONTACTED.
• ANY CHANGES OR ALTERATIONS TO THIS APPLIANCE OR ITS CONTROLS CAN BE DANGEROUS
AND IS PROHIBITED.
• Do not operate appliance before reading and understanding operating instructions. Failure to operate
appliance according to operating instructions could cause fire or injury.
• Risk of fire or asphyxiation do not operate appliance with fixed glass removed.
• Do not connect 110 volts to the control valve.
• Risk of burns. The appliance should be turned off and cooled before servicing.
• Do not install damaged, incomplete or substitute components.
• Risk of cuts and abrasions. Wear protective gloves and safety glasses during installation. Sheet metal edges
may be sharp.
• Do not burn wood or other materials in this appliance.
• Children and adults should be alerted to the hazards of high surface temperature and should stay away to
avoid burns or clothing ignition.
• Young children should be carefully supervised when they are in the same room as the appliance. Toddlers,
young children and others may be susceptible to accidental contact burns. A physical barrier is recommended
if there are at risk individuals in the house. To restrict access to an appliance, install an adjustable safety gate
to keep toddlers, young children and other at risk individuals out of the room and away from hot surfaces.
• Clothing or other flammable material should not be placed on or near the appliance.
• Due to high temperatures, the appliance should be located out of traffic and away from furniture and draperies.
• Ensure you have incorporated adequate safety measure to protect infants/toddlers from touching hot surfaces.
• Even after the appliance is out, the glass and/or screen will remain hot for an extended period of time.
• Check with your local hearth specialty dealer for safety screens and hearth guards to protect children from hot
surfaces. These screens and guards must be fastened to the floor.
• Any safety screen or guard removed for servicing must be replaced prior to operating the appliance.
• The appliance is a vented gas-fired appliance. Do not burn wood or other materials in the appliance
• It is imperative that the control compartments, burners and circulating blower and its passageway in the
appliance and venting system are kept clean. The appliance and its venting system should be inspected
before use and at least annually by a qualified service person. More frequent cleaning may be required due
to excessive lint from carpeting, bedding material, etc. The appliance area must be kept clear and free from
combustible materials, gasoline and other flammable vapors and liquids.
• Under no circumstances should this appliance be modified.
• This appliance must not be connected to a chimney flue pipe serving a separate solid fuel burning appliance.
• Do not use this appliance if any part has been under water. Immediately call a qualified service technician to
inspect the appliance and to replace any part of the control system and any gas control which has been under
water.
• Do not operate the appliance with the glass door removed, cracked or broken. Replacement of the glass
should be done by a licensed or qualified service person.
• Do not strike or slam shut the appliance glass door.
• When equipped with pressure relief doors, they must be kept closed while the appliance is operating to
prevent exhaust fumes containing carbon monoxide, from entering into the home. Temperatures of the exhaust
escaping through these openings can also cause the surrounding combustible materials to overheat and catch
fire.
• Only doors / optional fronts certified with the appliance are to be installed on the appliance.
• Keep the packaging material out of reach of children and dispose of the material in a safe manner. As with all
plastic bags, these are not toys and should be kept away from children and infants.
• As with any combustion appliance, we recommend having your appliance regularly inspected and serviced as
well as having a Carbon Monoxide Detector installed in the same area to defend you and your family against
Carbon Monoxide.
• Ensure clearances to combustibles are maintained when building a mantel or shelves above the appliance.
Elevated temperatures on the wall or in the air above the appliance can cause melting, discolouration or
damage of decorations, a T.V. or other electronic components.

W415-1198 / 05.24.13
5
EN
2.1 DIMENSIONS
THIS GAS APPLIANCE SHOULD BE INSTALLED AND SERVICED BY A QUALIFIED INSTALLER to
conform with local codes. Installation practices vary from region to region and it is important to know the
specifics that apply to your area, for example in Massachusetts State:
• This product must be installed by a licensed plumber or gas fitter when installed within the commonwealth
of Massachusetts.
• The appliance damper must be removed or welded in the open position prior to installation of an appliance
insert or gas log.
• The appliance off valve must be a “T” handle gas cock.
• The flexible connector must not be longer than 36 inches (914.4mm).
• ACarbon Monoxide detector is required in all rooms containing gas fired appliances.
• The appliance is not approved for installation in a bedroom or bathroom unless the unit is a direct vent
sealed combustion product.
ALWAYS LIGHT THE PILOT WHETHER FOR THE FIRST TIME OR IF THE GAS SUPPLY HAS RUN OUT,
WITH THE GLASS DOOR OPENED OR REMOVED.
PROVIDE ADEQUATE CLEARANCE FOR SERVICING AND OPERATING THE APPLIANCE.
PROVIDE ADEQUATE VENTILATION.
NEVER OBSTRUCT THE FRONT OPENING OF THE APPLIANCE.
OBJECTS PLACED IN FRONT OF THE APPLIANCE MUST BE KEPT A MINIMUM OF 48” (1219.2mm)
FROM THE FRONT FACE OF THE APPLIANCE.
SURFACES AROUND AND ESPECIALLY ABOVE THE APPLIANCE CAN BECOME HOT. AVOID CONTACT
WHEN THE APPLIANCE IS OPERATING.
FIRE RISK. EXPLOSION HAZARD.
HIGH PRESSURE WILL DAMAGE VALVE. DISCONNECT GAS SUPPLY PIPING BEFORE PRESSURE TESTING GAS
LINE AT TEST PRESSURES ABOVE 1/2 PSIG. CLOSE THE MANUAL SHUT-OFF VALVE BEFORE PRESSURE
TESTING GAS LINE AT TEST PRESSURES EQUAL TO OR LESS THAN 1/2 PSIG (35 mb).
USE ONLY WOLF STEEL APPROVED OPTIONAL ACCESSORIES AND REPLACEMENT PARTS WITH THIS APPLIANCE.
USING NON-LISTED ACCESSORIES (BLOWERS, DOORS, LOUVRES, TRIMS, GAS COMPONENTS, VENTING
COMPONENTS, ETC.) COULD RESULT IN A SAFETY HAZARD AND WILL VOID THE WARRANTY AND CERTIFICATION.
!
WARNING
Thisappliance mustbe recessed into a vented noncombustible wood-burning appliance (prefabricated or masonry)
only. The minimum appliance opening size in which the appliance is to be installed is:
HEIGHT 211/2" (546.1mm) WIDTH 29" (736.6mm) DEPTH *131/2" (342.9mm)
The minimum allowable chimney flue size is 7" (177.8mm) round.
*Add 4" (101.6mm) for optional blower.
The minimum distance, from the bottom of a combustible mantel projecting 3" (76.2mm) maximum from the
wall to the top of the appliance, is 14" (355.6mm) (See MINIMUM MANTEL CLEARANCES section).
NOTE: A NON-COMBUSTIBLE HEARTH MUST PROTRUDEA MINIMUM OF 12" (304.8mm) FROM THE
APPLIANCE.
2.2 MINIMUM CLEARANCE TO COMBUSTIBLES
91/2”
(241.3mm)
21”
(533.4mm)
201/2”
(520.7mm)
171/2”
(444.5mm)
171/2”
(444.5mm)
12”
(304.8mm)
283/4”
(730.3mm)
235/8”
(600.1mm)
295/8”
(752.5mm)
131/4”
(336.6mm)
91/2”
(241.3mm)
2.3 GENERAL INSTRUCTIONS

W415-1198 /05.24.13
6
EN
2.4 GENERAL INFORMATION 4.1B
The installation must conform with local codes or, in
absence of local codes, the National Gas and Propane
Installation Code CSA B149.1 in Canada, or the National
Fuel Gas Code, ANSI Z223.1 / NFPA 54 in the United
States. Suitable for mobile home installation if installed in
accordance with the current standard CAN/CSA Z240MH
Series, for gas equipped mobile homes, in Canada or
A
NSI Z223.1 and NFPA 54 in the United States.
A
s long as the required clearance to combustibles is
maintained, the most desirable and beneficial location
for an appliance is in the center of a building, thereby
allowing the most efficient use of the heat created. The location of windows, doors and the traffic flow in the
room where the appliance is to be located should be considered. If possible, you should choose a location
where the vent will pass through the house without cutting a floor or roof joist.
If the appliance is installed directly on carpeting, vinyl tile or other combustible material other than wood
flooring, the appliance shall be installed on a metal or wood panel extending the full width and depth.
Some appliances have optional fans or blowers. If an optional fan or blower is installed, the junction box must
be electrically connected and grounded in accordance with local codes, use the current CSA C22.1 Canadian
Electrical Code in Canada or the ANSI/NFPA 70 National Electrical code in the United States.
We suggest that our gas
hearth products be installed
and serviced by professionals
who are certied in the U.S.
by the National Fireplace
Institute
® (NFI) as NFI Gas
Specialists
www.ncertied.org
FOR YOUR SATISFACTION, THIS APPLIANCE HAS BEEN TEST-FIRED TO ASSURE ITS OPERATION
AND QUALITY!
IR3-1
NG LP
Altitude (FT) 0-4,500 0-4,500
Max. Input (BTU/HR) 24,000 24,000
Max. Output (BTU/HR) 18,480 18,480
Efficiency (w/the fan on) 77% 77%
A.F.U.E. (maximum value) 76% 76%
Min. Inlet Gas Supply Pressure 4.5" Water Column (11.3mb) 11" Water Column (27.4mb)
Max. Inlet Gas Supply Pressure 7" Water Column (17.4mb) 13" Water Column (32.4mb)
Manifold Pressure (Under Flow Conditions) 3.5" Water Column (8.7mb) 10" Water Column (24.9mb)
When the appliance is installed at elevations above 4,500ft (1371.6m), and in the absence of specific
recommendations from the local authority having jurisdiction, the certified high altitude input rating shall be
reduced at the rate of 4% for each additional 1,000ft (304.8m). Expansion / contraction noises during heating
up and cooling down cycles are normal and to be expected.
This appliance is not approved for closet or recessed installations. It is approved for bathroom, bedroom and
bed-sitting room installations and is suitable for mobile homes. The natural gas model is suitable for installation
in a mobile home that is permanently positioned on its site and fuelled with natural gas.
64.2%
IR3-1

W415-1198 / 05.24.13
7
EN
2.5 RATING PLATE INFORMATION
INSTALLER: It is your responsibility to check off the appropriate box on the rating plate according to
the model, venting and gas type of the appliance.
For rating plate location, see “INSTALLATION OVERVIEW” section.
This illustration is for reference only. Refer to the rating plate on the appliance for accurate information.
NOTE: The rating plate must remain with the appliance at all times. It must not be removed.
SERIAL NUMBER/NO. DE SERIE: IR3/CIR3
WARNING: DO NOTADDANYMATERIAL TO THEAPPLIANCE THAT WILLCOME IN
CONTACT WITHTHE FLAMES, OTHER THAN THAT SUPPLIED BY THE MANUFACTURER
WITH THE APPLIANCE.
DECORATIVE PRODUCT: NOT FOR USE AS A HEATING APPLIANCE.
AVERTISSEMENT: N'A JOUTEZ PAS A CETAPPAREIL AUCUN MATERIAU DEVANT
ENTRER ENCONTACTAVEC LES FLAMMESAUTRE QUECELUIQUI EST FOURNIAVEC CET
APPAREIL PAR LE FABRICANT.
PRODUIT DÉCORATIF: NE PAS UTILISER COMME APPAREIL DE CHAUFFAGE.
W385-0660 / C
CERTIFIED FOR
CERTIFIEE POUR CANADA USA
IR3N IR3PCIR3N CIR3P
MODEL
CERTIFIED
REFERENCE #161746
Natural Gas/Gaz Naturel Propane
CE FOYER À GAZ VENTILÉS NE DOIT PAS ÊTRE UTILISÉ
CONJOINTEMENT AVEC DES FILTRES À AIR. UTILISER AVEC LES
PORTES VITRÉES HOMOLOGUÉES AVEC CETTE UNITÉ SEULE-
MENT. UN COMBUSTIBLE SOLIDE NE DOIT PAS ETRE UTILISE
AVEC CET APPAREIL.
CERTIFIED UNDER / HOMOLOGUÉ SELON LES NORMES: ANSI Z21.50b-2009, CSA2.22b-2009 VENTED GAS FIREPLACE / FOYER À GAS VENTILÉ.
WOLF STEEL LTD.
24 NAPOLEON ROAD, BARRIE. ONTARIO L4M 0G8 CANADA
ELECTRICAL RATING: 115V 1.5AMP 60HZ
THE APPLIANCE MUST BE VENTED USING THEAPPROPRIATE WOLF STEEL VENT KITS. SEE
OWNER’S INSTALLATION MANUALFOR VENTING SPECIFICS. PROPER REINSTALLATIONAND
RESEALING IS NECESSARYAFTER SERVICING THE VENT-AIR INTAKE SYSTEM.
WARNING: FOR INSTALLATION INTOAVENTED NON-COMBUSTIBLE FIREPLACE ONLY. THE
MINIMUM FIREPLACE SIZE IS: HEIGHT 20.5”, DEPTH 13.25”, WIDTH 29”. THE MINIMUM INSIDE
FLUE SIZE IS 6”. THE MINIMUM DISTANCE FROM THE BOTTOM OFA COMBUSTIBLE MANTEL
PROJECTING A MAXIMUM 3” FROM THE WALLTO THE TOP OF THE UNIT IS 12”. SEE OWNER’S
MANUAL FOR GREATER EXTENSIONS.
OPTIONAL FAN KIT - GZ550-KT, GD65.
CLASS : 115V, 1.5AMP, 60HZ
L’APPAREIL DOIT EVACUER SES GAZ EN UTILISANT L’ENSEMBLE D’EVACUATION PROPRE A WOLF STEEL. REFERER
AU MANUEL D’INSTALLATION DE PROPRIETAIRE POUR L’EVACUATION PRECISE. IL EST IMPORTANT DE BIEN
REINSTALLER ET RESCELLER L’EVENT APRES AVOIR ASSURE LE MAINTIEN DU SYSTEME DE PRISE D’AIR.
ATTENTION : POUR INSTALLATION DANS UN FOYER VENTILE EN MACONNERIE. LES DIMENSIONS MINIMUMS SONT:
HAUTER 19.75”, PROFONDEUR 13.25”, LARGEUR 29”. LE DIAMETRE INTERIEUR MINIMUM DE CONDUIT D’EVACUATION
EST DE 6”. LA DISTANCE MINIMALE, DU BAS DU MANTEAU COMBUSTIBLE FORMANT UNE PROJECTION MAXIMALE DE
3” DU MUR AU DESSUS DE LA GARNITURE NORMALE EST 12”. REFERER AU MANUEL D’INSTALLATION POUR DES
EXTENSIONS PLUS GRANDES.
SOUFFLERIE OPTIONELLE GZ550-KT, GD65.
NE PAS ALLUMER SI DES ENFANTS OU D’AUTRES INDIVIDUS À RISQUE
SONT À PROXIMITÉ DU FOYER. FOYER À GAZ VENTILÉ. HOMOLOGUÉ POUR
INSTALLATION DANS UNE CHAMBRE À COUCHER, UNE SALLE DE BAIN ET
UN STUDIO. APPROPRIÉ POUR INSTALLATION DANS UNE MAISON MOBILE
SI SON INSTALLATION EST CONFORME AUX EXIGENCES DE LANORME
CAN/CSA Z240MH SÉRIE DE MAISONS MOBILES ÉQUIPÉES AU GAZ, EN
VIGUEUR AU CANADA, OU AUX ÉTATS-UNIS, SELON LA NORME DE
SÉCURITÉ ET DE CONSTRUCTION DE MAISONS MANUFACTURÉES, TITRE
24 CFR, SECTION 3280. DANS LE CAS OÙ CETTE NORME DES ÉTATS-UNIS
NE PEUT ÊTREAPPLIQUÉE, SE RÉFÉRER À LA NORME RELATIVE AU
CRITÈRE DE MESURES DE SÉCURITÉ CONTRE L'INCENDIE POUR LES
INSTALLATIONS DANS LES MAISONS MANUFACTURÉES, LES SITES ET LES
COMMUNAUTÉS, ANSI/NFPA 501A.
DO NOT TURN ON IF CHILDREN OR OTHERAT RISK INDIVIDUALS
ARE NEAR THE FIREPLACE. DIRECT VENT GAS FIREPLACE.
SUITABLE FOR BEDROOM, BATHROOMAND BED-SITTING ROOM
INSTALLATION. SUITABLE FOR MOBILE HOME INSTALLATION IF
INSTALLED IN ACCORDANCE WITH THE CURRENT STANDARD
CAN/CSA Z240MH SERIES GAS EQUIPPED MOBILE HOMES, IN
CANADA OR IN THE UNITED STATES THE MANUFACTURED HOME
CONTRUCTION AND SAFETY STANDARD, TITLE 24 CFR, PART 3280.
WHEN THIS US STANDARD IS NOT APPLICABLE USE THE
STANDARD FOR FIRE SAFETY CRITERIA FOR MANUFACTURED
HOME INSTALLATIONS, SITESAND COMMUNITIES, ANSI / NFPA
501A.
4500FT (0-1370m) ALTITUDE/ELEVATION 4500FT (0-1370m)
24,000 BTU/h INPUT/ALIMENTATION 24,000 BTU/h
18,000 BTU/h REDUCED INPUT/ALIMENTATION REDUITE 18,000 BTU/h
MANIFOLD PRESSURE: 3.5” WATER COLUMN
PRESSION AU COLLECTEUR: 3.5” D’UNE COLONNE D’EAU
MINIMUM SUPPLY PRESSURE: 4.5” WATER COLUMN
PRESSION D’ALIMENTATION MINIMALE: 4.5” D’UNE COLONNE D’EAU
MAXIMUM SUPPLY PRESSURE: 7.0” WATER COLUMN
PERSSION D’ALIMENTATION MAXIMALE: 7.0” D’UNE COLONNE D’EAU
P4: 64.2%
MANIFOLD PRESSURE: 10” WATER COLUMN
PRESSION AU COLLECTEUR: 10” D’UNE COLONNE D’EAU
MINIMUM SUPPLY PRESSURE: 11” WATER COLUMN
PRESSION D’ALIMENTATION MINIMALE: 11” D’UNE COLONNE D’EAU
MAXIMUM SUPPLY PRESSURE: 13” WATER COLUMN
PERSSION D’ALIMENTATION MAXIMALE: 13” D’UNE COLONNE D’EAU
P4: 64.2%
THIS VENTED GAS FIREPLACE HEATER IS NOT FOR USE
WITH AIR FILTERS. FOR USE WITH GLASS DOORS CERTIFIED
FOR THIS UNIT ONLY. NOT FOR USE WITH SOLID FUEL.
SAMPLE
HEAPPLIANCE THAT WILL COME INTHAT WILL COME IN
N THAT SUPPLIED BY THE MANUFACTUREN THAT SUPPLIED BY THE MANUFACTUR
SE AS A HEATING APPLIANCE.SE AS A HEATING APPLIANCE.
DA USA
A USA
PL
IR3PIR3P
MODELMODEL
SAMPLE
1746
P
CE FC
COC
FIREPLACE / FOYIREPLACE / FO
EL LTD.
L LTD.
N ROAD, BARRIE. ONROAD, BARRIE. O
0HZ
USING THEAPPROPRIATE WOLF STEEL VENTHE APPROPRIATE WOLF STEEL V
AL FOR VENTING SPECIFICS. PROPER REINSTING SPECIFICS. PROPER REINS
FTER SERVICING THE VENT-AIR INTAKE SYSG THE VENT-AIR INTAKE SYS
ON INTOA VENTED NON-COMBUSTIBLE FIREN INTOA VENTED NON-COMBUSTIBLE FIR
ZE IS: HEIGHT 20.5”, DEPTH 13.25”, WIDTH 29”ZE IS: HEIGHT 20.5”, DEPTH 13.25”, WI
MINIMUM DISTANCE FROM THE BOTTOM OF AMINIMUM DISTANCE FROM THE BOTTO
XIMUM 3” FROM THE WALL TO THE TOP OF THIMUM 3” FROM THE WALL TO THE TOP O
EATER EXTENSIONS.
ATER EXTENSIONS.
N KIT - GZ550-KT, GD65.
T - GZ550-KT, GD65.
UMER SI DES ENFANTSUMER SI DES ENFAN
ROXIMITÉ DU FOYER. FOYROXIMITÉ DU FOYER. F
LLATION DANS UNE CHAMBRE ÀLATION DANS UNE CHAMBRE À
STUDIO. APPROPRIÉ POUR INSTALLATUDIO. APPROPRIÉ POUR INSTALLAT
SON INSTALLATION EST CONFORME AUX
STALLATION EST CONFORME AU
CAN/CSA Z240MH SÉRIE DE MAISONS MO40MH SÉRIE DE MAISONS MO
VIGUEUR AU CANADA, OU AUX ÉTATS-CANADA, OU AUX ÉTATS-
SÉCURITÉ ET DE CONSTRUCTION DCONSTRUCTION D
24 CFR, SECTION 3280. DANS LE C280. DANS LE
NE PEUT ÊTREAPPLIQUÉE, SENE PEUT ÊTREAPPLIQUÉE, SE
CRITÈRE DE MESURES DE SÉCRITÈRE DE MESURES DE S
INSTALLATIONS DANS LESINSTALLATIONS DANS L
COMMUNAUTÉS, ANSI/NCOMMUNAUTÉS, ANSI/N
ITUDE/ELEVATION 45TUDE/ELEVATION 4
PUT/ALIMENTATIONPUT/ALIMENTATION
D INPUT/ALIMENTATION REDUITENPUT/ALIMENTATION RE
TER COLUMNER COLUMN
OLONNE D’EAUOLONNE D’EAU
” WATER COLUMNWATER CO
NE COLONNE D’EAUE COLONNE D’E
E:
7.0” WATER COLUMN0” WATER COLUMN
” D’UNE COLONNE D’EAUCOLONNE D’EAU
P
4
:P4:
64.2
%64.2%
MANIFOLD PRESSUREMANIFO
PRESSION AU COLLPRESS
MINIMUM SUPPLYMINIMUM
PRESSION D’ALPRESSION
MAXIMUM SUMAXIMUM S
PERSSIONERSSION
P
4
:
64.2%64.2
R IS NOT FOR USER IS NOT FOR USE
GLASS DOORS CERTIFIEDLASS DOORS CERTIFIED
SE WITH SOLID FUEL.TH SOLID FUEL.

W415-1198 /05.24.13
8
EN
3.0 INSTALLATION
3.1 LEVELLING THE APPLIANCE
68.4B
Clean out ashes from the inside of the wood-burning appliance. Make sure that the chimney and wood-burning
appliance are in a clean and sound condition and constructed of non-combustible materials. If necessary have
any repair work done by a qualified person before installing the insert. Remove the existing appliance damper
or lock into an open position.
Using screws, attach the appliance warning tag
to the inside of the firebox of the appliance into
which the insert is being installed.
The sheet-metal parts of the appliance, in which
the gas appliance insert is to be installed, must
not be cut.
If the wood-burning factory-built appliance has
no gas access hole(s) provided, an access hole of 1½ inch (38.1mm) or less may be drilled through the lower
sides or bottom of the appliance in a proper workman like manner. This access hole must be plugged with non
-
combustible insulation after the gas supply line has been installed.
Ensure that existing chimney cleanouts fit properly.
The refractory, glass doors, screen rails, screen mesh and log grates may be removed from the existing
appliance before installing the gas appliance insert.
Smoke shelves, shields and baffles may be removed if attached by mechanical fasteners.
The ventilation openings in the existing appliance may be obstructed by the backer plates, aluminium trim etc.
but these parts are not to be applied so as to have an airtight seal.
!
WARNING
RISK OF FIRE, MAINTAIN SPECIFIED AIR SPACE CLEARANCES TO VENT PIPE AND APPLIANCE.
W385-0199_B
WARNING: THIS FIREPLACE HAS BEEN CONVERTED FOR USE WITHA GAS FIREPLACE
INSERT ONLYAND CANNOT BE USED FOR BURNING WOOD OR SOLID FUELS UNLESSALL ORIGINAL
PARTS HAVE BEEN REPLACED ANDTHE FIREPLACE IS RE-APPROVED BY THEAUTHORITY HAVING
JURISDICTION.
ATTENTION: CE FOYER AETE CONVERTIAFIN D’ETRE UTILISE SEULEMENT
COMME FOYER ENCASTRE AU GAZ ET NE PEUT ETRE UTILSE POUR BRULER DU BOIS OU
TOUTAUTRE COMBUSTIBLE SOLIDE, SANS QUE TOUTES LES PIECES ORIGINALESAIENT
ETE REMPLACEES ET QUE LE FOYER SOITAPPROUVE DE NOUVEAU PAR LES AUTORITES
AYANT JURIDICTION.
ADVERTENCIA: ESTA CHIMENEASE REMODELÓ PARA USARSE SOLO CON UNA
INSERCIÓN DE CHIMENEAAGAS Y NO PUEDE USARSE PARA QUEMAR MADERA NI COMBUSTIBLES
SÓLIDOS, A MENOS QUE SE HAYAN REEMPLAZADO TODAS LAS PIEZAS ORIGINALES, Y LAAUTORI-
DAD JURISDICCIONAL LA HAYA VUELTO A APROBAR.
Move the appliance close to its final position. This appliance is equipped with levelling screws located on the
base. Level using the levelling screws. Levelling the appliance will eliminate rocking or excessive noise when
the fan is in operation. Once the appliance is level, move it partially into place to allow for all connections to be
made. It is not practical to level the appliance once it has been installed. Determine the required depth prior to
installing the appliance and adjust the levelling screws accordingly. 67.2

W415-1198 / 05.24.13
9
EN
While the liners must be continuous from the appliance to the chimney cap, to
achieve the needed length, they may be coupled, using an approved coupler.
We recommend that exhaust vents that pass through unheated spaces,
such as tall exterior chimneys, be wrapped in a protective sleeve to minimize
condensation and reverse flow symptoms. See Trouble Shooting for details.
This appliance is approved for use with a 3" (76.2mm) exhaust and air intake.
A. OUTSIDE: Slip the one end of a liner a minimum of 2" (50.8mm)
over the sleeve of the air terminal. Secure using 3 screws. Then
seal the joint and screw heads with high temperature sealant.
Repeat with the other liner.
NOTE: We recommend that the other end of the exhaust liner be marked to eliminate the
exhaust liner being connected to the intake collar at the appliance.
B. Gently stretch the liners to the
required lengths and insert into
the chimney. Trim and fit the
flashing plate to suit the chimney
termination. Place the air terminal
onto the top of the chimney.
Make weather tight by sealing
with caulking (not supplied).
Fasten to the chimney with
screws and plugs (not supplied).
C. INSIDE: Remove the securing
screw from the front of the vent
mounting plate. Pull the vent
mounting plate only, back into
the track, to the front stop. Start
the slider back into position. Re-
secure the screw. The appliance
may now be pushed into its
final position inside the wood
burning appliance, and the screw
tightened until the slider has
been pulled tight to the front stop.
D. Route the flex liners through
the slider. Attach and secure
the liners to the vent mounting plate using the same procedure as before, ensuring that the marked
exhaust liner is attached to the exhaust collar.
FLASHING
PLATE
2” (50.8mm)
OVERLAP
SEALANT
HI-TEMP
INTAKE
EXHAUST
SECURING
SCREW
SLIDER
MOUNTING
PLATE
HIGH TEMP
SEALANT
2” (50.8mm)
OVERLAP
3” (76.2mm)
LINERS
EXHAUST
INTAKE
VENT MOUNT
ASSEMBLY
3.2 CHIMNEY CONNECTION
Chimney installation must conform to both national and local code requirements. The chimney must be lined
with one 3" (76.2mm) diameter liner for intake and one 3" (76.2mm) diameter liner for exhaust. The minimum
and maximum vent lengths are 10 ft (3.1m) and 35 ft (10.7m) respectively.
Recommended kits come in 3 lengths:
2-3" DOUBLE PLY ALUMINUM LINER-INLET AND EXHAUST:
GDI-320KT VENT KIT 20FT (6.1m)
GDI-325KT VENT KIT 25 FT (7.6m)
GDI-335KT VENT KIT 35 FT (10.7m)

W415-1198 /05.24.13
10
EN
3.3 GAS INSTALLATION
30.1
Installation and servicing to be done by a qualified installer. Do not use open flame.
• Move the appliance into position and secure.
• If equipped with a flex connector the appliance is designed to accept a 1/2” (12.7mm) gas supply.
Without the connector it is designed to accept a 3/8” (9.5mm) gas supply. The appliance is equipped
with a manual shut off valve to turn off the gas supply to the appliance.
• Connect the gas supply in accordance to local codes. In the absence of local codes, install to the
current CAN/CSA-B149.1 Installation Code in Canada or to the current National Fuel Gas Code, ANSI
Z223.1 / NFPA 54 in the United States.
• When flexing any gas line, support the gas valve so that the lines are not bent or kinked.
• Check for gas leaks by brushing on a soap and water solution.
!
WARNING
RISK OF FIRE, EXPLOSION OR ASPHYXIATION. ENSURE THERE ARE NO IGNITION SOURCES SUCH AS
SPARKS OR OPEN FLAMES.
SUPPORT GAS CONTROL WHEN ATTACHING GAS SUPPLY PIPE TO PREVENT DAMAGING GAS LINE.
ALWAYS LIGHT THE PILOT WHETHER FOR THE FIRST TIME OR IF THE GAS SUPPLY HAS RUN OUT
WITH THE GLASS DOOR OPENED OR REMOVED. PURGING OF THE GAS SUPPLY LINE SHOULD BE
PERFORMED BY A QUALIFIED SERVICE TECHNICIAN. ASSURE THAT A CONTINUOUS GAS FLOW IS AT
THE BURNER BEFORE CLOSING THE DOOR. ENSURE ADEQUATE VENTILATION. FOR GAS AND
ELECTRICAL LOCATIONS, SEE “DIMENSION” SECTION.
ALL GAS CONNECTIONS MUST BE CONTAINED WITHIN THE APPLIANCE WHEN COMPLETE.
HIGH PRESSURE WILL DAMAGE VALVE. DISCONNECT GAS SUPPLY PIPING BEFORE TESTING GAS
LINE AT TEST PRESSURES ABOVE 1/2 PSIG.
VALVE SETTINGS HAVE BEEN FACTORY SET, DO NOT CHANGE.
4.0 FINISHING
!
WARNING
RISK OF FIRE!
NEVER OBSTRUCT THE FRONT OPENING OF THE APPLIANCE.
THE FRONT OF THE APPLIANCE MUST BE FINISHED WITH ANY NON-COMBUSTIBLE MATERIALS
SUCH AS BRICK, MARBLE, GRANITE, ETC., PROVIDED THAT THESE MATERIALS DO NOT GO
BELOW THE SPECIFIED DIMENSION AS ILLUSTRATED.
DO NOT STRIKE, SLAM OR SCRATCH GLASS. DO NOT OPERATE APPLIANCE WITH GLASS
REMOVED, CRACKED, BROKEN OR SCRATCHED.
FACING AND/OR FINISHING MATERIAL MUST NEVER OVERHANG INTO THE APPLIANCE OPENING.
72.1A

W415-1198 / 05.24.13
11
EN
Combustible mantel clearance can vary
according to the mantel depth. Use the
graph to help evaluate the clearance
needed. These same requirements
apply to any combustibles protruding
on either side of the appliance.
H
DF
G
MANTEL DEPTH
0” (mm)
+
(
,
*
+
7
0
$
1
7
(
/
E
C
B
A
!
WARNING
RISK OF FIRE, MAINTAIN ALL SPECIFIED AIR SPACE CLEARANCES TO COMBUSTIBLES. FAILURE
TO COMPLY WITH THESE INSTRUCTIONS MAY CAUSE A FIRE OR CAUSE THE APPLIANCE TO
OVERHEAT. ENSURE ALL CLEARANCES (I.E. BACK, SIDE, TOP, VENT, MANTEL, FRONT, ETC.) ARE
CLEARLY MAINTAINED.
WHEN USING PAINT OR LACQUER TO FINISH THE MANTEL, THE PAINT OR LACQUER MUST BE
HEAT RESISTANT TO PREVENT DISCOLOURATION. 73.1
4.1 MINIMUM MANTEL CLEARANCES
D
ABC
EF
H
G
201/2”
(520.7mm)
4.2 DOOR REMOVAL AND INSTALLATION
!
WARNING
GLASS MAY BE HOT, DO NOT TOUCH GLASS UNTIL COOLED.
THE DOOR LATCHES ARE PART OF A SAFETY SYSTEM AND MUST BE PROPERLY ENGAGED. DO
NOT OPERATE THE APPLIANCE WITH LATCHES DISENGAGED.
FACING AND/OR FINISHING MATERIALS MUST NOT INTERFERE WITH AIR FLOW THROUGH AIR
OPENINGS, LOUVRES OPENINGS, OPERATION OF LOUVRES OR DOORS OR ACCESS FOR
SERVICE. OBSERVE ALL CLEARANCES WHEN APPLYING COMBUSTIBLE MATERIALS.
BEFORE DOOR IS REMOVED TURN THE APPLIANCE OFF AND WAIT UNTIL APPLIANCE IS COOL TO
THE TOUCH. DOORS ARE HEAVY AND FRAGILE SO HANDLE WITH CARE.
75.1
DOOR LATCH
The optional front must be removed to allow the door to be opened or closed. Release the top left and right
door latches, located at the top of the door. Tilt forward and lift from slots.
MANTEL DIMENSIONS
Ref Height Ref Depth
A17" (431.8mm) E6" (152.4mm)
B16" (406.4mm) F5" (127mm)
C15" (381mm) G4" (101.6mm)
D14” (355.6mm) H3" (76.2mm)

W415-1198 /05.24.13
12
EN
4.3 LOG PLACEMENT
!
WARNING
FAILURE TO POSITION THE LOGS IN ACCORDANCE WITH THESE DIAGRAMS OR FAILURE TO USE
ONLY LOGS SPECIFICALLY APPROVED WITH THIS APPLIANCE MAY RESULT IN PROPERTY
DAMAGE OR PERSONAL INJURY.
LOGS MUST BE PLACED IN THEIR EXACT LOCATION IN THE APPLIANCE. DO NOT MODIFY THE
PROPER LOG POSITIONS, SINCE APPLIANCE MAY NOT FUNCTION PROPERLY AND DELAYED
IGNITION MAY OCCUR.
THE LOGS ARE FRAGILE AND SHOULD BE HANDLED WITH CARE.
76.1A
E. Position the right charcoal strip
in front of the right middle log, lining
up the holes in the bottom with the
2 front right studs.
F. Position a pin (supplied) into the
left side hole of the rear log, move
the left crossover log into position,
lining up the top hole with the pin in
the rear log.
C. Place the right middle log into
position, lining up the two holes in
the bottom with the studs located on
the right side of the burner.
D. Position the left charcoal strip in
front of the left middle log, lining up
the holes in the bottom with the 2
front left studs.
PHAZERTM logs and glowing embers exclusive to Napoleon, provide a unique and realistic glowing effect that is
different in every installation. Take the time to carefully position the glowing embers for a maximum glowing effect.
Log colours may vary. During the initial use of the appliance, the colours will become more uniform as colour
pigments burn in during the heat activated curing process.
A. Place the rear log behind the left
and right log supports and ensure
that it's tight to the burner. Make sure
to centre the pilot in the notch.Adjust
the log supports tight to the log to
hold it in an upright position.
B. Place the left middle log into
position, lining up the two holes in
the bottom with the studs located
on the left side of the burner.
LOG SUPPORT
G. Position a pin into the right side
hole of the rear log, move the right
crossover log into position, lining
up the top hole with the pin in the
rear log.

W415-1198 / 05.24.13
13
EN
Tear the embers into pieces and place along the front row of ports covering all of the burner area in front of
the small logs. Care should be taken to shred the embers into thin, small irregular pieces as only the exposed
edges of the fibre hairs will glow. The ember material will only glow when exposed to direct flame;
however, care should be taken to not block the burner ports.
Blocked burner ports can cause an incorrect flame pattern, carbon deposits and delayed ignition. PHAZERTM
logs glow when exposed to direct flame. Use only certified "glowing embers" and PHAZERTM logs available
from your authorized dealer / distributor.
97.1A
Remove the backing o
f
the logo supplied and place on the glass viewing door,
as indicated. ½"(12.7mm)
LOGO
½"(12.7mm)
4.4 OPTIONAL ROCK PLACEMENT
4.5 GLOWING EMBERS
4.6 LOGO PLACEMENT
Before beginning with the installation, remove the door and all burner media from the appliance including logs
and charcoal strips. Retain the glowing embers.
D. Reinstall the glowing embers over the burner.
E. Reinstall the door.
!
WARNING
REAL ROCKS MUST NOT BE USED IN THIS APPLIANCE. HEAT WILL CAUSE THEM TO EXPLODE
A. Sit the two rock clusters on top
of the rear log support. Ensure the
clusters are sitting flat.
B. Place the large notched rocks
along the step behind the front
burner as desired.
C. Place the remaining rocks around
the burner as desired making sure
not to cover any burner ports (there
are no set locations).
4.7 BATTERY INSTALLATION
4 AA batteries must be installed in to the (DC battery pack) before operation is possible. The battery pack
is located in the bottom right corner of the appliance. The door may have to be removed to access, refer to
"DOOR REMOVALAND INSTALLATION" section. (Refer to "INSTALLATION OVERVIEW" for battery location).

W415-1198 /05.24.13
14
EN
RECEIVER
GV60 VALVE
BATTERY
HOUSING
OFF ON
PSE PILOT
INTERRUPTER
BLOCK
BLACK WITH YELLOW TERMINAL END
BLACK WITH
RED TERMINAL END
RESET BUTTON
BLACK
(8 WIRE)
THERMOCOUPLE
WIRE
ORANGE
5.0 ELECTRICAL INFORMATION
5.1 WIRING DIAGRAM
This appliance comes equipped with a battery pack. Install 4 AA batteries into the holder that is connected to
the wire harness. Place near the front of the appliance for ease of changing batteries.
!
WARNING
DO NOT USE THIS APPLIANCE IF ANY PART HAS BEEN UNDER WATER. CALL A QUALIFIED
SERVICE TECHNICIAN IMMEDIATELY TO HAVE THE APPLIANCE INSPECTED FOR DAMAGE TO THE
ELECTRICAL CIRCUIT.
RISK OF ELECTRICAL SHOCK OR EXPLOSION. DO NOT WIRE 110V TO THE VALVE OR TO THE
APPLIANCE WALL SWITCH. INCORRECT WIRING WILL DAMAGE CONTROLS.
ALL WIRING SHOULD BE DONE BY A QUALIFIED ELECTRICIAN AND SHALL BE IN COMPLIANCE
WITH LOCAL CODES. IN THE ABSENCE OF LOCAL CODES, USE THE CURRENT CSA22.1 CANADIAN
ELECTRIC CODE IN CANADA OR THE CURRENT NATIONAL ELECTRIC CODE ANSI/NFPA NO. 70 IN
THE UNITED STATES.
ALWAYS LIGHT THE PILOT WHETHER FOR THE FIRST TIME OR IF THE GAS SUPPLY HAS RAN OUT,
WITH THE GLASS DOOR OPENED OR REMOVED.
69.2

W415-1198 / 05.24.13
15
EN
6.0 OPERATION
When lit for the first time, the appliance will emit a slight odour for a few hours. This is a normal temporary
condition caused by the "burn-in" of internal paints and lubricants used in the manufacturing process and
will not occur again. Simply open a window to sufficiently ventilate the room.After extended periods of non-
operation such as following a vacation or a warm weather season, the appliance may emit a slight odour for
a few hours. This is caused by dust particles in the heat exchanger burning off. Open a window to sufficiently
ventilate the room.
IF YOU DO NOT FOLLOW THESE INSTRUCTIONS EXACTLY, A FIRE OR EXPLOSION MAY RESULT
CAUSING PROPERTY DAMAGE, PERSONAL INJURY OR LOSS OF LIFE.
ALWAYS LIGHT THE PILOT WHETHER FOR THE FIRST TIME OR IF THE GAS SUPPLY HAS RUN OUT WITH
THE GLASS DOOR OPENED OR REMOVED.
!
WARNING
6.1 OPERATING AND LIGHTING INSTRUCTIONS
OPERATING INSTRUCTIONS / INSTRUCTIONS D’OPERATION
FOR YOUR SAFETY READ BEFORE OPERATING / POUR VOTRE SÉCURITÉ LIRE AVANT DE FAIRE FONCTIONNER
WARNING: IF YOU DO NOT FOLLOW THESE INSTRUC-
TIONS EXACTLY, AFIRE OR EXPLOSION MAY RESULT
CAUSING PROPERTY DAMAGE, PERSONALINJURY OR
LOSS OF LIFE.
INITIAL LIGHTING OF THE PILOTAND MAIN BURNERS
MUST BE DONE WITH THE GLASS DOOR OFF.
DO NOT CONNECT VALVE OR WALL SWITCH TO ELEC-
TRICITY. SEE INSTALLATION INSTRUCTIONS.
A. THIS FIREPLACE IS EQUIPPED WITHAN IGNITION DEVICE WHICH AUTOMATI-
CALLY LIGHTS THE PILOT. DO NOT TRY TO LIGHT BY HAND.
B. BEFORE OPERATING SMELL ALLAROUND THE FIREPLACEAREA FOR GAS
AND NEXT TOTHE FLOOR BECAUSE SOME GAS IS HEAVIER THANAIR AND WILL
SETTLE ON THE FLOOR.
WHAT TO DO IF YOU SMELL GAS:
• TURN OFF ALL GAS TO THE FIREPLACE.
• OPEN WINDOWS.
• DO NOT TRYTO LIGHTANY APPLIANCE.
• DO NOT TOUCHANY ELECTRIC SWITCH; DO NOT USEANY PHONE IN YOUR
BUILDING.
• IMMEDIATELY CALLYOUR GAS SUPPLIER FROM ANEIGHBOUR’S PHONE.
FOLLOW THE GAS SUPPLIER’S INSTRUCTIONS.
• IF YOU CANNOT REACH YOUR GAS SUPPLIER, CALLTHE FIRE DEPARTMENT.
C. DO NOT TRYTO REPAIR ANYPARTOF THIS ASSEMBLY. CALL AQUALIFIED
SERVICE TECHNICIAN. FORCE ORATTEMPTED REPAIR MAY RESULT IN AFIRE
OR EXPLOSION.
D. DO NOT USE THIS FIREPLACE IFANY PART HAS BEEN UNDER WATER.
IMMEDIATELY CALLAQUALIFIED SERVICE TECHNICIAN TO INSPECT THE
FIREPLACE AND REPLACEANY PART OF THE CONTROL SYSTEMAND ANY GAS
CONTROL WHICH HAS BEEN UNDER WATER.
ATTENTION: SI CES INSTRUCTIONS NE SONT PAS OBSERVÉES A LA
LETTRE, UN FEU OU UNE EXPLOSION POURRAIT S’ENSUIVRE
CAUSANT DES DOMMAGESA LAPROPRIETE, DES BLESSURES
CORPORELLES OU PERTE DE VIE.
L’ ALLUMAGE INITIAL DE LAVEITLLEUSE ET DU BRULEUR PRINCIPAL
DOIT SE FAIRE AVEC LA PORTE VITREE ENLEVEE.
NE RACCORDEZ PAS LA SOUPAPE OU L’INTERRUPTEUR MURALA
L’ELECTRICITE.
CONSULTEZ LES INSTRUCTIONS D’INSTALLATION.
A. CETAPPAREILEST MUNI D’UN DISPOSITIF D’ALLUMAGE QUI ALLUME LAVEILLEUSE
AUTOMATIQUEMENT.
N’ESSAYEZ PAS D’ALLUMER LAVEILLEUSE MANUELLEMENT.
B. AVANT D’ALLUMER SENTEZ L’AIR AUTOUR DE L’APPAREIL ET PRÈS DU PLANCHER (CERTAINS
GAZ SONT PLUS LOURDS QUE L’AIR ET SE DÉPOSERONT AU NIVEAU DU PLANCHER) POUR
DÉTECTER UNE FUITE POSSIBLE.
QUE FAIRE SI VOUS DÉTECTEZ UNE ODEUR DE GAZ:
• COUPEZ L’ALIMENTATION DE GAZ PRINCIPALE.
• OUVREZ LES FENETRES.
• N’ALLUMEZ AUCUN APPAREIL.
• NE TOUCHEZ PAS À AUCUN INTERRUPTEUR ÉLECTRIQUE; N’UTILISEZAUCUN TÉLÉPHONE
DANS VOTRE IMMEUBLE.
• APPELEZ IMMÉDIATEMENT VOTRE FOURNISSEUR DE GAZ D’UN TÉLÉPHONE VOISIN ET SUIVEZ
SES INSTRUCTIONS.
• SI VOUS NE POUVEZ PAS REJOINDRE VOTRE FOURNISSEUR DE GAZ, APPELEZ LE SERVICE
DES
INCENDIES.
C. N’ESSAYEZ PAS DE RÉPARER AUCUNE PIÈCE DE CETASSEMBLAGE. APPELEZ UN
TECHNICIEN QUALIFIÉ. FORCER OU TENTER DE RÉPARER L’ASSEMBLAGE POURRAIT CAUSER
UN FEU OU UNE EXPLOSION.
D. N’UTILISEZ PAS CET APPAREIL SI UN DE SES COMPOSANTS À ÉTÉ SUBMERGÉ. CONTACTEZ
IMMÉDIATEMENT UN TECHNICIEN DE SERVICE QUALIFIÉ POUR INSPECTER L’APPAREIL ET
REMPLACER TOUT SYSTÈME DE CONTRÔLE DE GAZTOUCHÉ PAR L’EAU. W385-1907
LIGHTING INSTRUCTIONS / INSTRUCTIONS D’ALLUMAGE
1. STOP! READALL INFORMATION OF OPERATING AND LIGHTING
INSTRUCTIONS BEFORE PROCEEDING.
2. TURN REMOTE/WALLSWITCH TO THE “OFF” POSITION.
3. TURN OFF ELECTRIC POWER TO THE FIREPLACE AND/OR REMOVE THE
BATTERIES.
4. THIS FIREPLACE IS EQUIPPED WITH AN IGNITION DEVICE WHICH
AUTOMATICALLY LIGHTS THE PILOT. DO NOT TRYTO LIGHT THE PILOT
BY HAND.
5. OPEN THE GLASS DOOR.
6. TURN MANUAL SHUTOFF VALVE CLOCKWISE TO “OFF”.
7. WAIT FIVE (5) MINUTES TO CLEAR OUTANY GAS. IF YOU SMELLGAS
INCLUDING NEAR THE FLOOR, STOP! FOLLOW “B” OF THE OPERATING
INSTRUCTIONS. IF YOU DON’T SMELLGAS GO TO THE NEXT STEP.
8. CLOSE THE GLASS DOOR.
9. TURN MANUAL SHUTOFF VALVE COUNTER-CLOCKWISE TO “ON”.
10. TURN ON ALL ELECTRIC POWER TO THE FIREPLACE AND/OR
REINSTALL THE BATTERIES.
11. TURN REMOTE/WALL SWITCH TO THE “ON” POSITION.
1. ARRÊTEZ! LISEZ TOUTES LES INSTRUCTIONS DE FONCTIONNEMENT
ET D’ALLUMAGE AVANT DE CONTINUER.
2. TOURNEZ L’INTERRUPTEUR MURAL/TÉLÉCOMMANDE MANUELLE À “OFF”.
3. COUPEZ L’ALIMENTATION ÉLECTRIQUE À L’APPAREIL ET/OÙ ENLEVEZ
LES PILES.
4. CETAPPAREIL EST MUNI D’UN DISPOSITIF D’ALLUMAGE QUIALLUME
LAVEILLEUSE AUTOMATIQUEMENT, N’ESSAYEZ PAS D’ALLUMER LA
VEILLEUSE MANUELLEMENT.
5. OUVREZ LA PORTE VITRÉE.
6. TOURNEZ LASOUPAPE DE SECTIONNEMENT MANUELLE VERS LA
DROITE A “OFF”.
7. ATTENDEZ CINQ (5) MINUTES POUR QUE LE GAZ PUISSE
S’ÉCHAPPER. SI VOUS DÉTECTEZ UNE ODEUR DE GAZ, ARRÊTEZ!
SUIVEZ « B » DANS LES INSTRUCTIONS DE FONCTIONNEMENT. S’IL
N’YA PAS D’ODEUR DE GAZ, PASSEZ À L’ÉTAPE SUIVANTE.
8. FERMEZ LA PORTE VITRÉE.
9. TOURNEZ LASOUPAPE DE SECTIONNEMENT MANUELLE VERS LA
GAUCHE A “ON”.
10. RÉTABLISSEZ L’ALIMENTATION ÉLECTRIQUE AU FOYER ET/OÙ
INSTALLEZ LES PILES.
11. TOURNEZ L’INTERRUPTEUR MURAL/TÉLÉCOMMANDE MANUELLE À “ON”.
1. TURN OFF ALL ELECTRICAL POWER TO THE FIREPLACE IF SERVICE IS
TO BE PERFORMED.
2. TURN MANUAL SHUTOFF VALVE CLOCKWISE TO “OFF”. DO NOT
FORCE.
1. COUPEZ L’ALIMENTATION ÉLECTRIQUEAU FOYER SI UN TRAVAIL
D’ENTRETIEN DOIT SE FAIRE.
2. TOURNEZ LASOUPAPE D’ARRÉT MANUELLE VERS LA DROITE
À “OFF” NE FORCEZ PAS.
TO TURN OFF GAS / INSTRUCTIONS POUR COUPER LE GAZ
MANTEMPTIMER
P1 P2 AUX
F
Cam
pm
:

W415-1198 /05.24.13
16
EN
6.2 OPERATION
IF YOU DO NOT FOLLOW THESE INSTRUCTIONS EXACTLY, A FIRE OR EXPLOSION MAY RESULT
CAUSING PROPERTY DAMAGE, PERSONAL INJURY OR LOSS OF LIFE.
ALWAYS LIGHT THE PILOT WHETHER FOR THE FIRST TIME OR IF THE GAS SUPPLY HAS RUN OUT WITH
THE GLASS DOOR OPENED OR REMOVED.
!
WARNING
MANTEMPTIMER
P1
P2
F
Cam
pm
:
LOW BATTERY
INDICTOR
SIGNAL INDICTOR
TEMPERATURE
DISPLAY
TIME DISPLAY
MODES OF
OPERATION
TIMER DISPLAY
ON/OFF
TEMPERATURE
SETTING
SET BUTTON
OFF BUTTON
LARGE FLAME BUTTON
SMALL FLAME BUTTON
6.2.1 GENERAL REMOTE TRANSMITTER LAYOUT
6.2.2 PROGRAMMING
A. Press and hold the receiver's reset button until you hear two beeps. (First beep is short, second beep
is long.) Release the button after the second beep, refer to "INSTALLATION OVERVIEW" for receiver
location.
B. Within the subsequent 20 seconds press and hold the small flame button on the remote transmitter
until you hear two additional short beeps confirming the code is set, refer to "GENERAL REMOTE
TRANSMITTER LAYOUT". (NOTE: One long beep indicates the sequence has failed or wiring is
incorrect).
NOTE: This is a one time setting only, and is not required after changing the batteries of the remote or receiver.

W415-1198 / 05.24.13
17
EN
A. Using the remote transmitter press the "OFF" button.
NOTE: To turn the appliance on after pressing the "OFF" button, you must wait 30 seconds. The
appliance will shut off if no change has occured to the flame height or if the appliance has not turned
on for a period of 5 days.
A. Press the "Set" button to change modes.
B. The modes change in the following order:
NOTE: Refer to "GENERAL REMOTE TRANSMITTER LAYOUT".
MAN TEMP TEMP TIMER MAN
• For flame height adjustment in Manual Mode MAN double click the large flame button to
increase to the highest flame height. Double click the small flame button to decrease to the
lowest flame height. Press the large flame button to increase flame height or the small flame
button to decrease flame height. NOTE: Holding the small flame button for too long
will switch the appliance to pilot mode. To turn the appliance off completely press the
"OFF" button.
• For Daytime Temperature Mode TEMP the appliance must be set to standby mode (pilot
ignited). The default temperature setting for this mode is 23°C / 74°F. (Daytime Temperature
mode is set by comparing the set temperature and room temperature, the flame height is then
adjusted automatically to achieve this Daytime Temperature setting.)
• For Nighttime Temperature Mode TEMP the appliance must be set to standby mode (pilot
ignited). (Nighttime Temperature mode is set by comparing the night time set temperature and
room temperature, the flame height is then adjusted automatically to achieve this Nighttime
Temperature setting.)
• Timer Mode
TIMER the appliance must be set to standby mode (pilot ignited). There are two
timer settings available (P1 and P2) allowing the appliance turn off and to turn on at specified
times. NOTE: The "TIMER DISPLAY" indicates the set temperature every 30 seconds.
6.2.3 TURNING "ON" THE APPLIANCE
A. Place the "ON/OFF" switch in the "ON" position by the receiver, refer to "INSTALLATION OVERVIEW"
for location.
B. Using the remote transmitter simultaneously press the large flame button and the OFF button until
you hear a short beep, this confirms the start of the appliance, you can then release both buttons. (The
ignition process has begun once continuous beeping has begun).
C. Wait several seconds for the appliance to ignite. After main ignition the remote will default to the
Daytime Temperature Mode TEMP .
NOTE: Refer to "GENERAL REMOTE TRANSMITTER LAYOUT".
6.2.4 TURNING "OFF" THE APPLIANCE
6.2.5 HAND HELD REMOTE TRANSMITTER OPERATIONS

W415-1198 /05.24.13
18
EN
A. Using the remote transmitter you may set the flame directly to the "HI" setting by double clicking the
large flame button . Increasing the flame height can also be done by pressing and holding the large
flame button .
B. Using the remote transmitter you may set the flame directly to the "LO" setting by double clicking the
small flame button . Decrease the flame height can also be done by pressing and holding the small
flame button .
NOTE: For fine adjustment tap the large flame button or small flame button when using the remote
transmitter. If the small flame button is held too long the main burner will turn off.
NOTE: Time display will flash upon battery installation or when the large and small flame buttons are
pressed simultaneously.
A. To set the hour press the large flame button .
B. To set the minutes press the small flame button .
C. Press the "OFF" button to set the time.
A. To set the Timer Mode quickly press the SET button, scrolling to the desired mode.
B. To scroll through P1 , P1 , P2 ,P2 briefly press the set button.
C. Once the desired timer function is shown on the display and the time flashes, press the large flame
button to adjust the hour and the small flame button to adjust the minutes. Press the "OFF" button
to set the time.
NOTE: The default setting for the Timer Function is as follows: P1 6:00am and P2 8:00pm, P2
11:50 and P2 11:50, refer to "GENERAL REMOTE TRANSMITTER LAYOUT".
NOTE: Press the "OFF" button and the small flame button simultaneously until the temperature
display changes from Fahrenheit to Celsius, and vice versa. When changing from Fahrenheit to Celsius
the clock will change from a 12 hour to 24 hour clock, r
efer to "GENERAL REMOTE TRANSMITTER
LAYOUT".
A. To set Daytime Temperature Mode quickly press the SET button, scrolling to the desired mode, then
hold the SET button until the "TEMP" on the display flashes.
B. To increase the Daytime Temperature press the large flame button . To decrease the Daytime
Temperature press the small flame button . To use this setting as the new temperature press the OFF
button.
C. To set Nighttime Temperature Mode quickly press the SET button, scrolling to the desired mode, then
hold the SET button untill the "TEMP" on the display flashes.
D. To increase the Nighttime Temperature press the large flame button . To decrease the Nighttime
Temperature press the small flame button . To use this setting as the new temperature press the OFF
button.
NOTE: When in regular operation the remote will always show the room temperature.
6.2.6 TEMPERATURE DISPLAY
6.2.7 SETTING THE TIME
6.2.8 SETTING THE TIMER FUNCTION
6.2.9 FLAME HEIGHT

W415-1198 / 05.24.13
19
EN
A. Frequent beeping for 3 seconds when the appliance turns on indicates low battery on the remote
receiver. The battery pack is located on the bottom right side of the appliance, refer to "INSTALLATION
OVERVIEW" for location.
B. Low battery indicator is in the top right corner of the remote, we also recommend replacing the
batteries every two years.
NOTE: When low battery occurs the appliance will shut down. The appliance will shut off if no change
has occurred to the flame height or the appliance has not turned on for a period of 5 days.
IR3-1
NG 1/16” (1.6mm)
LP 3/8" (9.5mm)
Adjust the pilot screw to provide properly sized flame. Turn in a
clockwise direction to reduce the gas flow.
Check Pressure Readings:
Inlet pressure can be checked by turning screw (A) counter-clockwise
2 or 3 turns and then placing pressure gauge tubing over the test point.
Gauge should read as described on the chart below. Check that
main burner is operating on “HI”.
Outlet pressure can be checked the same as above using
screw (B). Gauge should read as described on the chart
below. Check that main burner is operating on “HI”.
AFTER TAKING PRESSURE READINGS, BE SURE TO
TURN SCREWS CLOCKWISE FIRMLY TO RESEAL. DO
NOT OVERTORQUE.
Leak test with a soap and water solution.
Prior to pilot adjustment, ensure that the pilot
assembly has not been painted. If overspray or
painting of the pilot assembly has occurred remove
the paint from the pilot assembly, or replace. Fine
emery cloth or sandpaper can be used to remove the paint from the pilot hood, electrode and flame sensor.
39.8A
A
B
PILOT
SCREW
FLAME MUST ENVELOP
UPPER 3/8” (9.5mm) TO 1/2”
(12.7mm) OF THERMOCOUPLE
PILOT
BURNER
ELECTRODE
THERMOCOUPLE
3/8” - 1/2”
(9.5mm - 12.7mm)
MANUAL
KNOB
Pressure
Inlet
Outlet
Natural Gas
(inches) Natural Gas (millibars) Propane (inches) Propane
(millibars)
7"
(MIN. 4.5")
3.5"
13"
(MIN. 11")
10"
17.4mb
(MIN. 11.2mb)
8.7mb
32.4mb
(MIN. 27.4mb)
24.9mb
This appliance has an air shutter that has been factory set open according
to the chart below:
Regardless of venturi orientation, closing the air shutter will cause a more
yellow flame, but can lead to carboning. Opening the air shutter will cause a
more blue flame, but can cause flame lifting from the burner ports. The
flame may not appear yellow immediately; allow 15 to 30 minutes for the
final flame colour to be established.
AIR SHUTTER ADJUSTMENT MUST ONLY BE DONE BY A QUALIFIED
INSTALLER!
AIR
SHUTTER
OPENING
VENTURI
BURNER
ORIFICE
49.1
6.2.10 LOW BATTERY
7.0 ADJUSTMENTS
7.1 PILOT BURNER ADJUSTMENT
7.2 VENTURI ADJUSTMENT

W415-1198 /05.24.13
20
EN
A. Remove the door from the appliance using the tool provided, refer to "DOOR REMOVALAND
INSTALLATION" section. There are two latches across the top of the door. Pull the latches forward and up off
of the flanges of the door. Ensure to keep one hand on the door at all times, to prevent it from falling on the
floor. When all latches have been released tilt the door forward and out of the bottom door retainer.
B. Remove the logs from the appliance.
C. Remove the burner from the appliance, refer to "BURNER REMOVAL" section.
D. Remove the main burner orifice and replace with the orifice supplied in the manual baggie. (Use pipe thread
compound)
E. Adjust the air shutter according to the "ADJUSTMENTS" section.
F. To convert the main valve to the desired fuel, remove the conversion plug using a screwdriver. Remove
plastic tip on the plug stem and rotate 180 degrees, refer to Figure 2. Re-secure to the conversion plug (it
should click into place).
G. Loosen the pilot hood by turning counter clockwise with a wrench until the conversion tab slides easily.
Slide the tab to the fuel desired. Tighten the pilot hood back to original position. NOTE: The tab is marked
with NAT. or LP, refer to Figure 1.
H. Reinstall the burner and then install the logs, refer to "LOG PLACEMENT" section.
I. The conversion data label found in the manual baggie, must
be filled out and attached adjacent to the valve.
J. Turn on the gas supply and check for gas leaks by
brushing on a soap and water solution. Do not use open
flame.
K. Light the pilot and main burner to ensure that the gas
lines have been purged. Refer to the "OPERATING AND
LIGHTING INSTRUCTIONS" section. Once all systems have
been checked, replace the log media.
L. Re-secure the door.
PILOT
HOOD
CONVERSION
TAB (NAT./LP)
THERMOCOUPLE
It’s important to periodically perform a visual check of the pilot and
burner flames. Compare them to the illustration provided. If any
flames appear abnormal call a service person.
FLAME MUST ENVELOP
UPPER 3/8” (9.5mm) TO 1/2”
(12.7mm) OF THERMOCOUPLE
PILOT
BURNER
ELECTRODE
THERMOCOUPLE
3/8” - 1/2”
(9.5mm - 12.7mm)
54.6
7.3 FLAME CHARACTERISTICS
7.4 LP CONVERSION
CONVERSION PLUG
NG position
LP position
180°
Diagrams courtesy of Maxitrol Company
FIGURE 1
FIGURE 2