Napoleon Haliburton GDS28P User manual

1
W415-0153 / B / 06.10.10
INSTALLER: LEAVE THIS MANUAL WITH THE APPLIANCE.
CONSUMER: RETAIN THIS MANUAL FOR FUTURE REFERENCE.
INSTALLATION AND
OPERATING INSTRUCTIONS
1.2A
Wolf Steel Ltd., 24 Napoleon Rd., Barrie, ON, L4M 4Y8 Canada /
103 Miller Drive, Crittenden, Kentucky, USA, 41030
Phone [phone] • Fax [phone] • www.napoleonfireplaces.com • [email protected]
SAFETY INFORMATION
!WARNING
If the information in these instructions are
not followed exactly, a fire or explosion
may result causing property damage,
personal injury or loss of life.
- Do not store or use gasoline or other flammable
vapors and liquids in the vicinity of this or any
other appliance.
- WHAT TO DO IF YOU SMELL GAS:
• Do not try to light any appliance.
• Do not touch any electrical switch; do not use
any phone in your building.
• Immediately call your gas supplier from a
neighbour’s phone. Follow the gas supplier’s
instructions.
• If you cannot reach your gas supplier, call the
fire department.
- Installation and service must be performed by a
qualified installer, service agency or the supplier.
CERTIFIED FOR CANADA AND UNITED STATES USING ANSI/CSA METHODS.
CERTIFIED UNDER CANADIAN AND AMERICAN NATIONAL STANDARDS: ANSI Z21.88 • CSA 2.33 FOR VENTED GAS FIREPLACE HEATERS.
$10.00
GDS28N & GS28N
NATURAL GAS
GDS28P & GS28P
PROPANE
Model GS28 is made up of Model GDS28 and B-Vent
Adapter Kit GS-150KT

2
W415-0153 / B / 06.10.10
NOTE: Changes, other than editorial, are denoted by a vertical line in the margin.
TABLE OF CONTENTS
1.0 INSTALLATION OVERVIEW 3
2.0 INTRODUCTION 4
2.1 DIMENSIONS 5
2.2 GENERAL INSTRUCTIONS 5
2.3 GENERAL INFORMATION 7
2.4 RATING PLATE INFORMATION 8
3.0 VENTING 9
3.1 VENTING LENGTHS AND COMPONENTS 10
3.2 TYPICAL VENT INSTALLATION 11
3.3 SPECIAL VENT INSTALLATIONS 12
3.3.1 PERISCOPE TERMINATION 12
3.4 VENT TERMINAL CLEARANCES 13
3.5 VENTING APPLICATION FLOW CHART 14
3.6 DEFINITIONS 14
3.7 ELBOW VENT LENGTH VALUES 14
3.8 TOP EXIT HORIZONTAL TERMINATION 15
3.9 TOP EXIT VERTICAL TERMINATION 17
3.10 VERTICAL THROUGH EXISTING CHIMNEY 19
4.0 INSTALLATION 20
4.1 MINIMUM CLEARANCES TO COMBUSTIBLES 20
4.2 WALL AND CEILING PROTECTION 21
4.2.1 HORIZONTAL INSTALLATION 21
4.2.2 VERTICAL INSTALLATION 22
4.2.3 HORIZONTAL AIR TERMINAL INSTALLATION - MODEL GDS28 22
4.2.4 VERTICAL AIR TERMINAL INSTALLATION 23
4.3 APPLIANCE VENT CONNECTION 24
4.4 MOBILE HOME INSTALLATION - MODEL GDS28 24
4.5 GAS INSTALLATION 25
4.6 OPTIONAL WALL SWITCH / THERMOSTAT / REMOTE 25
4.7 B-VENT SPECIFICS 26
4.7.1 CHIMNEY INSTALLATION 26
4.7.2 INSTALLING "B" VENT 27
4.7.3 B-VENT 27
4.7.4 COMBUSTION AIR 28
4.7.5 ADDING VENT SECTIONS 28
5.0 FINISHING 29
5.1 DOOR CLOSING AND OPENING 29
5.2 LOG PLACEMENT 30
5.3 GLOWING EMBERS 31
5.4 CHARCOAL EMBERS 31
5.5 LOGO PLACEMENT 31
6.0 OPERATION 32
6.1 OPERATING/LIGHTING INSTRUCTIONS 33
7.0 ADJUSTMENT 34
7.1 PILOT BURNER ADJUSTMENT 34
7.2 VENTURI ADJUSTMENT 34
7.3 FLAME CHARACTERISTICS 35
7.4 RESTRICTING VERTICAL VENTS - MODEL GDS28 35
8.0 MAINTENANCE 36
8.1 CARE OF GLASS 36
8.2 BLOWER REPLACEMENT 37
9.0 REPLACEMENTS 38
10.0 TROUBLE SHOOTING 42
11.0 WARRANTY 45
12.0 SERVICE HISTORY 46

3
W415-0153 / B / 06.10.10
Door, see “DOOR CLOSING /
OPENING” section.
Rating plate, see
“RATING PLATE” section.
Logo, see “LOGO
PLACEMENT” section.
Vent, see “VENTING” section.
1.0 INSTALLATION OVERVIEW

4
W415-0153 / B / 06.10.10
3.1A
!
WARNING
• THIS APPLIANCE IS HOT WHEN OPERATED AND CAN CAUSE SEVERE BURNS IF CONTACTED.
• Do not operate appliance before reading and understanding operating instructions. Failure to operate
appliance according to operating instructions could cause fire or injury.
• Risk of fire or asphyxiation do not operate appliance with fixed glass removed.
• Do not connect 110 volts to the control valve.
• Risk of burns. The appliance should be turned off and cooled before servicing.
• Do not install damaged, incomplete or substitute components.
• Risk of cuts and abrasions. Wear protective gloves and safety glasses during installation. Sheet metal
edges may be sharp.
• Do not burn wood or other materials in this appliance.
• Young children should be carefully supervised when they are in the same room as the appliance.
Toddlers, young children and others may be susceptible to accidental contact burns. A physical barrier
is recommended if there are at risk individuals in the house. To restrict access to an appliance or stove,
install an adjustable safety gate to keep toddlers, young children and other at risk individuals out of the
room and away from hot surfaces.
• Clothing or other flammable material should not be placed on or near the appliance.
• Due to high temperatures, the appliance should be located out of traffic and away from furniture and
draperies.
• Ensure you have incorporated adequate safety measure to protect infants/toddlers from touching hot
surfaces.
• Even after the appliance is out, the glass and/or screen will remain hot for an extended period of time.
• Check with your local hearth specialty dealer for safety screens and hearth guards to protect children
from hot surfaces. These screens and guards must be fastened to the floor.
• Any safety screen or guard removed for servicing must be replaced prior to operating the appliance.
• It is imperative that the control compartments, burners and circulating blower and its passageway in the
appliance and venting system are kept clean. The appliance and its venting system should be inspected
before use and at least annually by a qualified service person. More frequent cleaning may be required
due to excessive lint from carpeting, bedding material, etc. The appliance area must be kept clear and
free from combustible materials, gasoline and other flammable vapors and liquids.
• Under no circumstances should this appliance be modified.
• This appliance must not be connected to a chimney flue pipe serving a separate solid fuel burning
appliance.
• Do not use this appliance if any part has been under water. Immediately call a qualified service
technician to inspect the appliance and to replace any part of the control system and any gas control
which has been under water.
• Do not operate the appliance with the glass door removed, cracked or broken. Replacement of the glass
should be done by a licensed or qualified service person.
• Do not strike or slam shut the appliance glass door.
• This appliance uses and requires a fast acting thermocouple. Replace only with a fast acting
thermocouple supplied by Wolf Steel Ltd.
• Pressure relief doors must be kept closed while the appliance is operating to prevent exhaust fumes
containing carbon monoxide, from entering into the home. Temperatures of the exhaust escaping
through these openings can also cause the surrounding combustible materials to overheat and catch
fire.
• Only doors / optional fronts certified with the unit are to be installed on the appliance.
• Keep the packaging material out of reach of children and dispose of the material in a safe manner. As
with all plastic bags, these are not toys and should be kept away from children and infants.
• As with any combustion appliance, we recommend having your appliance regularly inspected and
serviced as well as having a Carbon Monoxide Detector installed in the same area to defend you and
your family against Carbon Monoxide.
• Ensure clearances to combustibles are maintained when building a mantel or shelves above the
appliance. Elevated temperatures can cause melting, deformation, discolouration or premature failure of
T.V. or other electronic components.
2.0 INTRODUCTION

5
W415-0153 / B / 06.10.10
2.1 DIMENSIONS
22 1/2”
11 1/4”
26 3/4”
7” Ø AIR
INTAKE
4” Ø
FLUE
18 1/2”
5 1/2”
17 3/4”12”10”
GAS LINE ACCESS HOLE
LOCATED IN PEDESTAL
BASE
15”
WINDOW
OPENING
2.2 GENERAL INSTRUCTIONS
ALWAYS LIGHT THE PILOT WHETHER FOR THE FIRST TIME OR IF THE GAS SUPPLY HAS RAN OUT,
WITH THE GLASS DOOR OPENED OR REMOVED.
PROVIDE ADEQUATE CLEARANCE FOR SERVICING AND OPERATING THE APPLIANCE.
PROVIDE ADEQUATE VENTILATION.
NEVER OBSTRUCT THE FRONT OPENING OF THE APPLIANCE.
OBJECTS PLACED IN FRONT OF THE APPLIANCE MUST BE KEPT A MINIMUM OF 48” FROM THE
FRONT FACE OF THE UNIT.
SURFACES AROUND AND ESPECIALLY ABOVE THE APPLIANCE CAN BECOME HOT. AVOID CONTACT
WHEN THE APPLIANCE IS OPERATING.
FIRE RISK. EXPLOSION HAZARD.
HIGH PRESSURE WILL DAMAGE VALVE. DISCONNECT GAS SUPPLY PIPING BEFORE PRESSURE TESTING
GAS LINE AT TEST PRESSURES ABOVE 1/2 PSIG. CLOSE THE MANUAL SHUT-OFF VALVE BEFORE
PRESSURE TESTING GAS LINE AT TEST PRESSURES EQUAL TO OR LESS THAN 1/2 PSIG.
USE ONLY WOLF STEEL APPROVED OPTIONAL ACCESSORIES AND REPLACEMENT PARTS WITH THIS APPLIANCE.
USING NON-LISTED ACCESSORIES (BLOWERS, DOORS, LOUVRES, TRIMS, GAS COMPONENTS, VENTING
COMPONENTS, ETC.) COULD RESULT IN A SAFETY HAZARD AND WILL VOID THE WARRANTY AND CERTIFICATION.
!
WARNING

6
W415-0153 / B / 06.10.10
4.1
THIS GAS APPLIANCE SHOULD BE INSTALLED AND SERVICED BY A QUALIFIED INSTALLER to
conform with local codes. Installation practices vary from region to region and it is important to know the
specifics that apply to your area, for example in Massachusetts State:
• This product must be installed by a licensed plumber or gas fitter when installed within the commonwealth
of Massachusetts.
• The appliance damper must be removed or welded in the open position prior to installation of a appliance
insert or gas log.
• The appliance off valve must be a “T” handle gas cock.
• The flexible connector must not be longer than 36 inches.
• A Carbon Monoxide detector is required in all rooms containing gas fired appliances.
• The appliance is not approved for installation in a bedroom or bathroom unless the unit is a direct vent
sealed combustion product.
The installation must conform with local codes or, in
absence of local codes, the National Gas and Propane
Installation Code CSA B149.1 in Canada, or the National
Fuel Gas Code, ANSI Z223.1 / NFPA 54 in the United
States. Suitable for mobile home installation if installed in
accordance with the current standard CAN/CSA Z240MH
Series, for gas equipped mobile homes, in Canada or
A
NSI Z223.1 and NFPA 54 in the United States.
A
s long as the required clearance to combustibles is
maintained, the most desirable and beneficial location for an appliance is in the center of a building, thereby
allowing the most efficient use of the heat created. The location of windows, doors and the traffic flow in the
room where the appliance is to be located should be considered. If possible, you should choose a location
where the vent will pass through the house without cutting a floor or roof joist.
If the appliance is installed directly on carpeting, vinyl tile or other combustible material other than wood
flooring, the appliance shall be installed on a metal or wood panel extending the full width and depth.
If the optional fan or blower is installed, the junction box must be electrically connected and grounded in
accordance with local codes, use the current CSA C22.1 Canadian Electrical Code in Canada or the ANSI/
NFPA 70 National Electrical code in the United States.
We suggest that our gas
hearth products be installed
and serviced by professionals
who are certied in the U.S.
by the National Fireplace
Institute
® (NFI) as NFI Gas
Specialists
www.ncertied.org

7
W415-0153 / B / 06.10.10
2.3 GENERAL INFORMATION
GDS28 GS28
NG LP NG LP
Altitude (FT) 0-4,500 0-4500 0-4500 0-4500
Max. Input (BTU/HR) 30,000 26,000 30,000 26,000
Max. Output (BTU/HR) 25,500 22,360 24,600 21,600
Max. Steady State
Efficiency (w/the fan
on)
85% 86% 82% 83%
Max. A.F.U.E. 76% 77%
Min. Inlet Gas Supply
Pressure
4.5" Water Column 11" Water Column 4.5" Water Column 11" Water Column
Max. Inlet Gas Supply
Pressure
7" Water Column 13" Water Column 7" Water Column 13" Water Column
Manifold Pressure
(Under Flow
Conditions)
3.5" Water Column 10" Water Column 3.5" Water Column 10" Water Column
When the appliance is installed at elevations above 4,500 ft, and in the absence of specific recommendations from
the local authority having jurisdiction, the certified high altitude input rating shall be reduced at the rate of 4% for each
additional 1,000 ft.
Change in flame appearance from "HI" to "LO" is more evident in natural gas than in propane.
Expansion / contraction noises during heating up and cooling down cycles are normal and to be expected.
This appliance may be installed in an aftermarket permanently located, manufactured mobile home, where not
prohibited by local codes.
This appliance is only for use with the type of gas indicated on the rating plate. This appliance is not convertible
for use with other gases, unless a certified kit is used.
This appliance is approved for bedroom and bed-sitting room installations.
FOR YOUR SATISFACTION, THIS APPLIANCE HAS BEEN TEST-FIRED TO ASSURE ITS OPERATION
AND QUALITY!

8
W415-0153 / B / 06.10.10
INSTALLER: It is your
responsibility to check off the
appropriate box on the rating
plate according to the model,
venting and gas type of the unit.
For rating plate location, see
“INSTALLATION OVERVIEW”
section.
This illustration is for reference
only. Refer to the rating plate on the
appliance for accurate information.
MODEL CDVS280/GDS28 APPROVEDFOR BEDROOM,
BATHROOM & BEDSITTING ROOM INSTALLATION. SUITABLE
FOR MOBILE HOME INSTALLATION IF INSTALLED IN ACCOR-
DANCE WITH THE CURRENT STANDARD CAN/CSA Z240MH
SERIES GAS EQUIPPED MOBILE HOMES, IN CANADA OR IN
THE UNITED STATES THE MANUFACTURED HOME
CONTRUCTIONANDSAFETYSTANDARD,TITLE24 CFR, PART
3280. WHEN THIS US STANDARD IS NOT APPLICABLE USE
THE STANDARD FOR FIRE SAFETY CRITERIA FOR MANU-
FACTURED HOME INSTALLATIONS, SITES AND COMMUNI-
TIES, ANSI / NFPA 501A.
HOMOLOGUE POUR INSTALLATION DANS UNE CHAMBREA
COUCHER, UNE SALLE DE BAIN ET UN STUDIO. APPROPRIE
POUR INSTALLATION DANS UNE MAISON MOBILE SI SON
INSTALLATION CONFORMEAUX EXIGENCES DE LA NORME
CAN/CSA Z240MH SERIE DE MAISONS MOBILES EQUIPEES
AU GAZ, EN VIGUEUR AU CANADA OU AUX ETATS-UNIS DE
LA NORME DE SECURITE ET DE CONSTRUCTION DE
MAISONS MANUFACTUREES, TITRE 24 CFR, SECTION 3280.
DANS LE CAS OU CETTE NORME D'ETATS-UNIS NE PEUT
ETRE APPLIQUEE, SE REFERER A LA NORME RELATIVEAU
CRITERE DE MESURES DE SECURITE CONTRE L'INCENDIE
POUR LES INSTALLATIONS DANS LES MAISONS MANUFAC-
TURES,LES SITESETLES COMMUNAUTES,ANSI/NFPA501A
.
STEADY STATE EFFICIENCY (NG): 75% FAN OFF / 78% FAN ON
STEADY STATE EFFICIENCY (LP): 75% FAN OFF / 79% FAN ON
EFFICACITE CONSTANTE (GN): 75% VENT. ARRETE
78% VENT. FONCTIONNE
EFFICACITE CONSTANTE (GP): 75% VENTILATEURARRETE
79% VENTILATEUR FONCTIONNE
STEADYSTATEEFFICIENCYAPPLIES TO CANADAONLY / L'EFFICACITE
CONSTANTE S'APPLIQUENT SEULEMENTAUCANADA.
AFUE (NG/LP) (GN/GP): 64% / 65%
MINIMUMAND MAXIMUM HORIZONTAL VENTLENGTHS ARE
25 INCHES AND 20 FEETRESPECTIVELY. LES LONGUEURS
HORIZONTALES MINIMALE ET MAXIMALE SONT 25 POUCES
ET20 PIEDS RESPECTIVEMENT.
THE APPLIANCE MUST BE VENTED USING THE APPROPRI-
ATE NAPOLEON VENT KITS. SEE OWNERS INSTALLATION
MANUAL FOR VENTING SPECIFICS. PROPER REINSTALLA-
TION AND RESEALING IS NECESSARY AFTER SERVICING
THE VENT-AIR INTAKE SYSTEM.
L'APPAREIL DOIT EVACUER SES GAZ EN UTILISANT
L'ENSEMBLE D'EVACUATION PROPRE A NAPOLEON.
REFERER AU MANUEL D'INSTALLATION DE PROPRIETAIRE
POUR L'EVACUATION PRECISE. ILEST IMPORTANT DE BIEN
REINSTALLER ET RESCELLER L'EVENT APRES AVOIR AS-
SURE LE MAINTIEN DU SYSTEME DE PRISE D'AIR.
WOLF STEEL LTD
BARRIE,ONTARIO CANADA
MADE IN CANADA / FABRIQUE AU CANADA
W385-0165 / D
SERIALNUMBER
NO.DESERIE
MANIFOLDPRESSURE:3.5INCHESW.C.(NG)/10INCHESW.C.(LP)
PRESSIONAU COLLECTEUR:3.5"D'UNECOLONNE D'EAU(GN)
10" D'UNE COLONNE D'EAU (PG)
MIN SUPPLY PRESSURE: 4.5" W.C.(NG) / 11" W.C. (LP)
PRESSIOND'ALIMENTATIONMIN:4.5"D'UNECOLONNED'EAU(GN)
11" D'UNE COLONNE D'EAU (PG)
MAX. SUPPLY PRESSURE: 7" W.C. (NG) / 13" W.C. (LP)
PRESSIOND'ALIMENTATIONMAX:7"D'UNECOLONNED'EAU(GN)
13" D'UNE COLONNE D'EAU (PG)
FOR USE WITH GLASS DOORS CERTIFIED WITH THIS UNITONLY.
UTILISER AVEC LES PORTES VITREES HOMOLOGUEES
SEULEMENTAVECCETTEUNITE.
WARNING: DO NOT ADD ANY MATERIAL TO THE APPLIANCE,
WHICHWILLCOMEINCONTACTWITHTHEFLAMES,OTHERTHAN
THAT SUPPLIED BYTHE MANUFACTURERWITHTHEAPPLIANCE.
AVERTISSEMENT: N'AJOUTEZPASACETAPPAREILAUCUN
MATERIAU DEVANT ENTRER EN CONTACT AVEC LES
FLAMMES AUTRE QUE CELUI QUI EST
APPAREIL PAR LE FABRICANT.
MINIMUMCLEARANCETO COMBUSTIBLE
DEGAGEMENTSMINIMAUXDESMATERIAUX
A7" D17½"
B2" E6¼"
C1" F9½"
20"TO CEILING FROM STOVE TOP
20" ENTRE LE DESSUS DU FOYER ET LE PLAFOND
ELECTRICAL RATING / CLASS.: 115V 1.5AMP 60HZ
MODEL CS280/GS28 APPROVED FOR BEDROOM, &
BEDSITTING ROOM INSTALLATION. HOMOLOGUE POUR IN-
STALLATION DANS UNE CHAMBRE A COUCHER, & UN
STUDIO.
STEADYSTATE EFFICIENCY(NG): 80%FAN OFF /82%FANON
STEADY STATEEFFICIENCY(LP): 80%FANOFF/83%FANON
EFFICACITE CONSTANTE (GN): 80% VENT. ARRETE
82% VENT. FONCTIONNE
EFFICACITECONSTANTE(GP): 80%VENTILATEURARRETE
83% VENTILATEUR FONCTIONNE
STEADYSTATEEFFICIENCYAPPLIESTOCANADAONLY /L'EFFICACITE
CONSTANTE S'APPLIQUENT SEULEMENTAUCANADA.
AFUE (NG/LP) (GN/GP): 66% / 68%
THISAPPLIANCEMUSTBE INSTALLEDUSINGANADAPTERKIT
GS-150KT. CETAPPAREIL DOIT ETRE INSTALLE EN UTILISANT
UNENSEMBLEADAPTATEURGS-150KT.
NOT FOR USE WITH SOLID FUEL
UN COMBUSTIBLE SOLIDE NE DOIT PAS
ETRE UTILISEAVEC CET APPAREIL GDS/CDVS28
ALTITUDE/ELEVATION
INPUT / ALIMENTATION
REDUCED INPUT /ALIMENTATION REDUITE
OUTPUT(CDVS280/GDS28)RENDEMENT
OUTPUT(CS280/GS28)RENDEMENT
ORIFICE / INJECTEUR
DIRECTVENTMODEL
‘B’VENT MODEL
0-4500FT (0-1370m)
30,000 BTU/h
18,000 BTU/h
22,500 BTU/h
24,000 BTU/h
#38
0-4500FT(0-1370m)
26,000 BTU/h
15,000 BTU/h
19,500 BTU/h
20,800 BTU/h
#54
CERTIFIEDUNDER:CSA2.33-2009,ANSIZ21.88-2009VENTEDGASFIREPLACEHEATER. APPLIANCEMUSTBEINSTALLEDUSING
BURNER KIT:GDS28BN-KT,ORGDS28BP-KT.
HOMOLOGUE SELON LES NORMES: CSA2.33-2009, ANSI Z21.88-2009 FOYER DE CHAUFFAGEAU GAZ AVEC EVACU-
ATION. CETAPPAREILDOITETRE INSTALLEENUTILISANT UNENSEMBLE DU BRULEUR:GDS28BN-KT,OUGDS28BP-KT.
CDVS280-N
CS280-N
GDS28-N
GS28-N
GDS28-P
GS28-P
CDVS280-P
CS28-P
REFERENCE # W/N 15486
2.4 RATING PLATE INFORMATION
SAMPLE
SS
2828
APPROVEDAPPROVE
NGNG
ROO
M
ROOM
IN
SNS
TT
ALLALL
TT
T
AA
TI
A
N
SS
TT
AA
TT
T
LLLL
AA
TIOTIO
AA
A
NN
IFIF
II
NN
SS
T
A
T
LLL
EE
DD
CURRENREN
TT
SS
TT
ANDARDANDA
TT
T
CAN/CSCAN/CS
A
A
UIPPED
MO
BIL
EOBILE
HO
ME
S,HOMES,
I
NIN
CANCAN
D
S
T
ATE
S
TH
EHE
M
AN
UMANU
FF
ACTUACTU
IONON
AN
D
S
AFE
T
Y
S
T
ANDARD,ANDARD,
T
TITTIT
H
EE
NN
TT
HH
I
SIS
U
S
S
T
A
T
NDA
R
DI
SIS
NN
OO
TT
T
ANDARDNDARD
T
F
ORFO
F
IR
E
S
AFE
TSAFET
Y
CC
TURED
HO
M
EHOME
IN
SINS
T
ALLL
T
AA
TIONS,TIONS
AAA
IES,ES,
AN
S
I
ANSI
/
NFF
PP
AA
PP
P
501501
AA
..
HOMOLOGUEHOMOLOGUE
P
OUROUR
IN
SINS
TT
ALLALL
TT
T
AA
TT
AA
A
CC
OO
UCHUCH
EE
RR
,,
UNU
E
S
A
A
L
LLL
EE
DD
EE
BAB
P
OURPO
IN
SINS
TT
ALLA
TT
T
A
TION
A
DANDAN
II
NN
SS
TT
AA
TT
T
L
LLL
AA
TIOTIO
AA
A
N
C
O
N
FO
R
C
AN
/CS
A
CAN/CSA
Z24
0
M
H
SE
A
UAU
G
AZ,
GAZ,
E
NE
VIGUE
LA
A
NN
OO
R
M
ERME
DE
M
AI
SO
N
SSONS
MANMA
DAN
SDA
L
ELE
CC
ETR
EETRE
AP
CRCR
ITEITE
POUPOU
T
,
H
AA
NN
ANCECE
..
L
AA
UCUUC
N
AA
VECVEC
AA
L
ELE
SS
AUXAUX
TOTO
P
FOYERFOYER
E
TET
L
E
PLAF
ONON
DD
CLASS.:CLASS.:
11
1
5V15V
1.
5
AM
1.5A
P
60H0H
Z
Z
CS280/GS28CS280/G
APPR
O
VED
APPROV
FO
TINGING
ROO
M
ROOM
IN
SINS
TT
ALLALL
TT
T
AA
LL
L
TIONON
A
..
HH
OO
MM
O
LL
A
A
TIONTION
AAA
DAN
SDANS
U
N
EUNE
CHAMBRECHAMBRE
DIO
O
..
Y
SS
TT
AA
TT
T
TT
AA
A
EE
E
FFI
C
IEN
CEFFICIENC
Y
Y
(NG):(NG
T
A
T
TE
A
E
FFI
C
IEN
CFFICIENC
Y
Y
(L(L
CONSONS
TT
ANTEANTE
TT
T
((
S
T
AN
T
AM
AM
AM
AM
AM
AM
AM
AM
AM
AM
AM
AM
AM
AM
AM
AM
AM
A
A
AM
AM
M
M
M
M
M
M
M
M
M
AM
M
M
AM
AM
SAMPLE
CC
SS

9
W415-0153 / B / 06.10.10
3.0 VENTING
7.1
THIS APPLIANCE USES A 4” EXHAUST / 7” AIR INTAKE VENT PIPE SYSTEM.
Refer to the section applicable to your installation.
For safe and proper operation of the appliance follow the venting instruction exactly. Deviation from the
minimum vertical vent length can create difficulty in burner start-up and/or carboning. Under extreme vent
configurations, allow several minutes (5-15) for the flame to stabilize after ignition. Vent lengths that pass
through unheated spaces (attics, garages, crawl spaces) should be insulated with the insulation wrapped in
a protective sleeve to minimize condensation. Provide a means for visually checking the vent connection to
the appliance after the appliance is installed. Use a firestop, vent pipe shield or attic insulation shield when
penetrating interior walls, floor or ceiling.
NOTE: If for any reason the vent air intake system is disassembled; reinstall per the instructions
provided for the initial installation.
!
WARNING
RISK OF FIRE, MAINTAIN SPECIFIED AIR SPACE CLEARANCES TO VENT PIPE AND APPLIANCE.
IF VENTING IS INCLUDED WITH SPACERS THE VENT SYSTEM MUST BE SUPPORTED EVERY 3 FEET
FOR BOTH VERTICAL AND HORIZONTAL RUNS. USE SUPPORTS OR EQUIVALENT
NON-COMBUSTIBLE STRAPPING TO MAINTAIN THE REQUIRED CLEARANCE FROM
COMBUSTIBLES. USE WOLF STEEL LTD. SUPPORT RING ASSEMBLY W010-0370 OR EQUIVALENT
NON-COMBUSTIBLE STRAPPING TO MAINTAIN THE MINIMUM CLEARANCE TO COMBUSTIBLES
FOR BOTH VERTICAL AND HORIZONTAL RUNS. SPACERS ARE ATTACHED TO THE INNER PIPE AT
PREDETERMINED INTERVALS TO MAINTAIN AN EVEN AIR GAP TO THE OUTER PIPE. THIS GAP IS
REQUIRED FOR SAFE OPERATION. A SPACER IS REQUIRED AT THE START, MIDDLE AND END OF
EACH ELBOW TO ENSURE THIS GAP IS MAINTAINED. THESE SPACERS MUST NOT BE REMOVED.
A terminal shall not terminate directly above a sidewalk or paved driveway which is located between
two single family dwellings and serves both dwellings. Local codes or regulations may require different
clearances.
Do not allow the inside liner to bunch up on horizontal or vertical runs and elbows. Keep it pulled
tight. A 1-1/4" air gap all around between the inner liner and outer appliance pipe is required for safe
operation. Use a firestop when penetrating interior walls, floor or ceiling.

10
W415-0153 / B / 06.10.10
3.1 VENTING LENGTHS AND COMPONENTS
Use only Wolf Steel, Simpson Dura-Vent, Selkirk Direct Temp, American Metal Amerivent or Metal-Fab venting
components. Minimum and maximum vent lengths, for both horizontal and vertical installations, and air terminal
locations for either system are set out in this manual and must be adhered to. For Simpson Dura-Vent, Selkirk
Direct Temp, American Metal Amerivent and Metal-Fab follow the installation procedure provided with the venting
components.
A starter adaptor must be used with the following vent systems and may be purchased from the corresponding
supplier:
* For Simpson Dura-Vent, Selkirk Direct Temp, American Metal Amerivent and Metal-Fab follow the
installation procedure found on the website for your venting supplier.
For vent systems that provide seals on the inner exhaust flue, only the outer air intake joints must be sealed using a
red high temperature silicone (RTV). This same sealant may be used on both the inner exhaust and outer intake vent
pipe joints of all other approved vent systems except for the exhaust vent pipe connection to the appliance flue collar
which must be sealed using the black high temperature sealant Mill Pac.
When using Wolf Steel venting components, use only approved Wolf Steel termination kits: wall terminal kit GD175
(7/12’ of venting included), or 1/12 to 7/12 pitch roof terminal kit GD110, 8/12 to 12/12 roof terminal kit GD111, flat
roof terminal kit GD112 or periscope kit GD180 (for wall penetration below grade) in conjunction with the appropriate
venting components.
For optimum flame appearance and appliance operation, keep the vent length and number of elbows to a
minimum. It is recommended that all horizontal runs have a minimum 1/4” rise per foot. The air terminal must
remain unobstructed at all times. Examine the air terminal at least once a year to verify that it is unobstructed
and undamaged. Rigid and flexible venting systems must not be combined. Different venting manufacturers
components must not be combined.
These vent kits allow for either horizontal or vertical venting of the appliance. The maximum allowable horizontal run
is 20 feet. The maximum allowable vertical vent length is 40 feet. The maximum number of vent connections is two
horizontally or three vertically (excluding the appliance and the air terminal connections) when using flexible venting.
Deviation from the minimum vertical vent length can create difficulty in burner start-up and/or carboning.
Use an adjustable pipe as the final length of rigid piping to the stove for ease of installation.
PART 4”/7” SUPPLIER WEBSITE
Duravent GDS924N Wolf Steel www.duravent.com
Amerivent 4DSC-N2 American Metal www.americanmetalproducts.com
Direct Temp 4DT-AAN Selkirk www.selkirkcorp.com
SuperSeal 4DNA Metal-Fab www.mtlfab.com
8.5

11
W415-0153 / B / 06.10.10
3.2 TYPICAL VENT INSTALLATION
26 3/4"
16" MINIMUM
40 FEET
MAXIMUM
3'
MINIMUM
26 3/4"
29" MINIMUM
55 3/4"
MINIMUM
PLUS RISE*
34" MAXIMUM
* See "VENTING" section.

12
W415-0153 / B / 06.10.10
Use the periscope kit to locate the air termination above grade. The periscope must be installed so that when
final grading is completed, the bottom air slot is located a minimum 12” above grade. The maximum allowable
vent length is 10’.
9.7
3.3 SPECIAL VENT INSTALLATIONS
57" MINIMUM
12"
MIN. TO
GRADE 12"
MIN. TO
GRADE
29" MINIMUM
26 3/4"
3.3.1 PERISCOPE TERMINATION
20 FT
MAX
26 3/4"

13
W415-0153 / B / 06.10.10
3.4 VENT TERMINAL CLEARANCES
INSTALLATIONS
CANADA U.S.A.
A12” 12” Clearance above grade, veranda porch, deck or balcony.
B12” Δ9” ΔClearance to windows or doors that open.
C12” * 12” * Clearance to permanently closed windows.
D18” ** 18” ** Vertical clearance to ventilated soffits located above the terminal within a horizontal distance of 2’ from
the centerline of the terminal.
E12” ** 12” ** Clearance to unventilated soffit.
F0” 0” Clearance to an outside corner wall.
G0” *** 0” *** Clearance to an inside non-combustible corner wall or protruding non-combustible obstructions (chimney, etc.).
2” *** 2” *** Clearance to an inside combustible corner wall or protruding combustible obstructions (vent chase, etc.).
H3’ 3’ **** Clearance to each side of the centerline extended above the meter / regulator assembly to a maximum
vertical distance of 15’.
I3’ 3’ **** Clearance to a service regulator vent outlet.
J12” 9” Clearance to a non-mechanical air supply inlet to the building or a combustion air inlet to any other appliance.
K6’ 3’ † Clearance to a mechanical air supply inlet.
L7’ ‡ 7’ **** Clearance above a paved sidewalk or paved driveway located on public property.
M12” †† 12” **** Clearance under a veranda, porch or deck.
N16” 16” Clearance above the roof.
O2’ †* 2’ †* Clearance from an adjacent wall including neighbouring buildings.
P8’ 8’ Roof must be non-combustible without openings.
Q3’ 3’ See chart for wider wall dimensions.
R6’ 6’ See chart for deeper wall dimensions. The terminal shall not be installed on any wall that has an open-
ing between the terminal and the open side of the structure.
S12” 12” Clearance under a covered balcony
ΔThe terminal shall not be located less than 6 feet under a window that opens on a horizontal plane in a structure with three walls and a roof.
* Recommended to prevent condensation on windows and thermal breakage
** it is recommended to use a heat shield and to maximize the distance to vinyl clad soffits.
*** The periscope requires a minimum 18 inches clearance from an inside corner.
**** This is a recommended distance. For additional requirements check local codes.
† 3 feet above if within 10 feet horizontally.
‡ A vent shall not terminate directly above a sidewalk or paved driveway that is located between two single family dwellings and serves both dwellings.
†† Permitted only if the veranda, porch, or deck is fully open on a minimum of two sides beneath the floor.
†* Recommended to prevent recirculation of exhaust products. For additional requirements check local codes.
††* Permitted only if the balcony is fully open on a minimum of one side.
12.1B
NOTE: Clearances are in accordance with local installation codes and the requirements of the gas supplier.
COVERED BALCONY APPLICATIONS ††*
QMIN
RMAX
MAX
R
= 3 feet
= 2 x
 feet
QACTUAL
R
QS
GP

14
W415-0153 / B / 06.10.10
3.6 DEFINITIONS
14.1
For the following symbols used in the venting calculations and examples are:
> - greater than
> - equal to or greater than
< - less than
< - equal to or less than
HT- total of both horizontal vent lengths (Hr) and offsets (Ho) in feet
HR- combined horizontal vent lengths in feet
HO- offset factor: .03 (total degrees of offset - 90°*) in feet
VT- combined vertical vent lengths in feet
3.5 VENTING APPLICATION FLOW CHART
13.1
TOP EXIT
Horizontal Termination Vertical Termination
Vertical rise is equal
to or greater than
the horizontal run
Vertical rise is less
than horizontal run
Vertical rise is equal
to or greater than
the horizontal run
Vertical rise is less
than horizontal run
Horizontal run +
vertical rise to
maximum of 40 feet
Horizontal run +
vertical rise to
maximum of 24.75
feet
Horizontal run +
vertical rise to
maximum of 40 feet
Horizontal run +
vertical rise to
maximum of 40 feet
4.2 times the
vertical rise equal to
or greater than the
horizontal run
3 times the vertical
rise equal to or
greater than the
horizontal run
3.7 ELBOW VENT LENGTH VALUES
15.1
FEET INCHES
1° 0.03 0.5
15° 0.45 6.0
30° 0.9 11.0
45° 1.35 16.0
90°* 2.7 32.0
* The first 90° offset has a zero value and is shown in the formula as - 90°

15
W415-0153 / B / 06.10.10
3.8 TOP EXIT HORIZONTAL TERMINATION
16.1A
Simple venting configuration (only one 90° elbow)
(HT) < (VT)
For vent configurations requiring more than one 90° elbow, the following formulas apply:
Formula 1: HT< VT
Formula 2: HT+ VT< 40 feet
Example 1:
V1= 3 FT
V2= 8 FT
VT= V1+ V2= 3 FT + 8 FT = 11 FT
H1= 2.5 FT
H2= 2 FT
HR= H1+ H2= 2.5 + 2 = 4.5 FT
HO= .03 (three 90° elbows - 90°) = .03 (270° - 90°) = 5.4 FT
HT= HR+ HO= 4.5 + 5.4 = 9.9 FT
HT+ VT= 9.9 + 11 = 20.9 FT
Formula 1: HT< VT
9.9 <11
Formula 2: HT+ VT< 40 FT
20.9 < 40
Since both formulas are met, this vent configuration is acceptable.
See graph to determine the required vertical
rise VTfor the required horizontal run HT.
The shaded area within the lines represents
acceptable values for HTand VT
02.5 5 7.5 10 12.5 15
40
10
20
30
17.5 20
39
REQUIRED
VERTICAL
RISE IN
FEET VT
HORIZONTAL VENT RUN PLUS OFFSET IN
FEET HT
90°
90°
90°
V1
V2
H1
H2

16
W415-0153 / B / 06.10.10
(HT) > (VT)
Simple venting configuration (only one 90° elbow) See graph to determine the required vertical rise VTfor the
required horizontal run HT.
REQUIRED
VERTICAL
RISE IN
INCHES VT
HORIZONTAL VENT RUN PLUS OFFSET IN FEET HT
0515
20
100
50
150
12.5’
29”
57”
147”
2.83’
The shaded area within the lines represents acceptable
values for HT and VT
For vent configurations requiring more than one 90° elbow, the following formulas apply:
Formula 1: H
T
< 4.2 V
T
Formula 2: H
T
+ V
T
< 24.75 feet
Example 2:
V
1
= V
T
= 6 FT
H
1
= 3 FT
H
2
= 5 FT
H
R
= H
1
+ H
2
= 3 + 5 = 8 FT
H
O
= .03 (two 90° elbows - 90°) = .03 (180° - 90°) = 2.7 FT
H
T
=H
R
+ H
O
= 8 + 2.7 = 10.7 FT
H
T
+ V
T
= 10.7 + 6 = 16.7 FT
Formula 1: H
T
< 4.2 V
T
4.2 V
T
=4.2 x 6 = 25.2 FT
Formula 2: H
T
+ V
T
< 24.75 FT
16.7 < 24.75
Since both formulas are met, this vent configuration is acceptable.
90°
V
1
H
1
H
2
90°
Example 3:
V1 = 4 FT
V2 = 1.5 FT
VT = V1 + V2 = 4 + 1.5 = 5.5 FT
H1 = 2 FT
H2 = 1 FT
H3 = 1 FT
H4 = 1.5 FT
HR = H1 + H2 + H3 + H4= 2 + 1 + 1 + 1.5 = 5.5 FT
HO = .03 (four 90° elbows - 90°) = .03 (360° - 90°) = 8.1 FT
HT =HR + HO = 5.5 + 8.1 = 13.6 FT
HT + VT = 13.6 + 5.5 = 19.1 FT
Formula 1: HT < 4.2 VT
4.2 VT =4.2 x 5.5 = 23.1 FT
13.6 < 23.1
Formula 2: HT + VT < 24.75 FT
19.1 < 24.75
Since both formulas are met, this vent configuration is acceptable.
90°
90°
90° 90°
H
1
H
2
V
1
V
2
H
3
H
4
10 19.5’
16.1_3A

17
W415-0153 / B / 06.10.10
3.9 TOP EXIT VERTICAL TERMINATION
(HT) < (VT)
Simple venting configurations. See graph to determine the required vertical rise VTfor the
required horizontal run HT.
REQUIRED
VERTICAL
RISE IN
FEET VT
HORIZONTAL VENT RUN PLUS OFFSET IN FEET HT
For vent configurations requiring one or more 90° elbows the following formulas apply:
Formula 1: HT< VT
Formula 2: HT+ VT < 40 feet
Example 6:
V1 = 5 FT
V2 = 6 FT
V3 = 10 FT
VT = V1 + V2 + V3 = 5 + 6 + 10 = 21 FT
H1 = 8 FT
H2 = 2.5 FT
HR = H1 + H2 = 8 + 2.5 = 10.5 FT
HO = .03 (four 90° elbows - 90°)
= .03 (360° - 90°) = 8.1 FT
HT =HR + HO = 10.5 + 8.1 = 18.6 FT
HT + VT = 18.6 + 21 = 39.6 FT
Formula 1: HT < VT
18.6 < 21
Formula 2: HT + VT < 40 FT
39.6 < 40
Since both formulas are met, this vent configuration is acceptable.
90°
V1
V2
H1
H2
The shaded area within the lines represents acceptable
values for HT and VT
90°
90°
90°
05101520
40
10
20
30
3
V3
18.1

18
W415-0153 / B / 06.10.10
(HT) > (VT)
Simple venting configurations. See graph to determine the required vertical rise VTfor the
required horizontal run HT.
REQUIRED
VERTICAL
RISE IN
FEET VT
HORIZONTAL VENT RUN PLUS OFFSET IN FEET HT
For vent configurations requiring more than two 90° elbows the following formulas apply:
Formula 1: HT< 3VT
Formula 2: HT+ VT < 40 feet
Example 2:
V1 = 2 FT
V2 = 1 FT
V3 = 1.5 FT
VT = V1 + V2 + V3 = 2 + 1 + 1.5 = 4.5 FT
H1 = 6 FT
H2 = 2 FT
HR = H1 + H2 = 6 + 2 = 8 FT
HO = .03 (four 90° elbows - 90°)
= .03 (360° - 90°) = 8.1 FT
HT =HR + HO = 8 + 8.1 = 16.1 FT
HT + VT = 16.1 + 4.5 = 20.6 FT
Formula 1: HT < 3VT
3VT = 3 x 4.5 = 13.5 FT
16.1 > 13.5
Since this formula is not met, this vent configuration is unacceptable.
Formula 2: HT + VT < 40 feet
20.6 < 40
Since only formula 2 is met, this vent configuration is unacceptable and a new fireplace location or vent configuration will
need to be established to satisfy both formulas.
The shaded area within the lines represents acceptable
values for HT and VT
05101520
10
20
3
25 30
19
90°
V1V2
H1
H2
90°
90°
90°
V3
18.1_2A

19
W415-0153 / B / 06.10.10
3.10 VERTICAL THROUGH EXISTING CHIMNEY
This appliance is designed to be attached to a 3" co-
linear flexible vent system running the full length of a
masonry chimney.
The flexible vent pipe accommodates any contours of
a masonry chimney, however, it is necessary to keep
the flexible vent pipe as straight as possible. The inlet
air collar of the termination cap must be connected to
the air intake pipe.
Use Simpson Duravent Chimney Liner Termination
Kit - 923GK (Base plate and Co-Linear to Co-Axial
Adaptor.
Follow manufacturers (Simpson Dura-Vent)
installation instructions.
When installing the appliance to this system,
Duravent vent components must be used. You must
start with a Duravent adaptor, GDS924N, directly off
the appliance. The GDS924N is only available at your
local authorized dealer / distributor.
40 FEET
MAXIMU
M
3 FEET
MINIMUM
FLEX
VENT
PIPE
EXHAUST
FLUE
PIPE
AIR
INTAKE
PIPE
62.5

20
W415-0153 / B / 06.10.10
4.0 INSTALLATION
!
WARNING
FOR SAFE AND PROPER OPERATION OF THE APPLIANCE, FOLLOW THE VENTING INSTRUCTIONS
EXACTLY.
ALL INNER EXHAUST AND OUTER INTAKE VENT PIPE JOINTS MAY BE SEALED USING EITHER RED
RTV HIGH TEMP SILICONE SEALANT W573-0002 (NOT SUPPLIED) OR BLACK HIGH TEMP MILL PAC
W573-0007 (NOT SUPPLIED) WITH THE EXCEPTION OF THE APPLIANCE EXHAUST FLUE COLLAR
WHICH MUST BE SEALED USING MILL PAC.
IF USING PIPE CLAMPS TO CONNECT VENT COMPONENTS, 3 SCREWS MUST ALSO BE USED TO
ENSURE THE CONNECTION CANNOT SLIP OFF.
DO NOT CLAMP THE FLEXIBLE VENT PIPE.
RISK OF FIRE, EXPLOSION OR ASPHYXIATION. IMPROPER SUPPORT OF THE ENTIRE VENTING
SYSTEM MAY ALLOW VENT TO SAG AND SEPARATE. USE VENT RUN SUPPORTS AND CONNECT
VENT SECTIONS PER INSTALLATION INSTRUCTIONS.
RISK OF FIRE, DO NOT ALLOW LOOSE MATERIALS OR INSULATION TO TOUCH THE VENT PIPE.
REMOVE INSULATION TO ALLOW FOR THE INSTALLATION OF THE ATTIC SHIELD AND TO
MAINTAIN CLEARANCES TO COMBUSTIBLES.
68.2A
4.1 MINIMUM CLEARANCES TO COMBUSTIBLES
Back Wall
Side Wall
Back Wall
Side Wall
Alcove
AAA
BB
C
D
E
F
45°
Back Wall
Side Wall
A7" D14 3/4"
B2" E4"
C1"* F9 1/2"
- No additional floor protection is required.
- A minimum 20" from stove top to ceiling
* At a distance of 1" from the wall, access to the blower switch, on/off switch or the blower power cord may
not be practical.