Napoleon S20-1 User manual

FRENCH PG. 43
W415-2796 / B / 12.19.19
ADD MANUAL TITLE
Wolf Steel Ltd., 24 Napoleon Rd., Barrie, ON, L4M 0G8 Canada / 103 Miller Drive, Crittenden, Kentucky, USA, 41030
Phone [phone] • www.napoleon.com • [e-mail]
ADD SAFETY STANDARD INFORMATION
& EPA QUALIFICATION (IF APPLICABLE)
Product Name / Code
(MUST use title from Price Book)
ADD ____ ILLUSTRATED
ADD PRODUCT IMAGE
CSA / OMNI
/ INTERTEK
LOGO
SAFETY INFORMATION
- This heater can be very hot when burning.
- Combustible materials such as fi rewood, wet clothing, etc. placed
too close can catch fi re.
- Children and pets must be kept from touching the heater when it is
hot.
- The chimney must be sound and free of cracks. Before installing this
appliance, contact the local building or fi re authority and follow their
guidelines.
- Always operate this appliance with the door(s) or screen (where
applicable) tightly closed.
- Burn wood behind the log retainer directly on the fi rebricks.
- Do not use an elevated grate or otherwise raise the fi re.
- This appliance is designed to burn natural wood only. Higher
effi ciencies and lower emissions generally result when burning air
dried seasoned hardwoods, as compared to softwoods or to green
or freshly cut hardwoods.
- Do not start a fi re with chemicals or fl uids such as gasoline, engine
oil, etc.
- Do not burn trash or garbage, lawn clippings/waste, rubber,
waste petroleum products, paints or paint thinners/solvents, plastic,
materials containing asbestos, construction debris, railroad ties or
treated wood, manure or animal remains, salt water driftwood or
salted materials, unseasoned wood, coal, charcoal, coloured paper,
cardboard, plywood or particleboard. Burning these materials may
result in release of toxic fumes or render the appliance ineffective and
cause smoke.
- Do not let the appliance become hot enough for any part to glow
red.
If the information in these instructions are not followed exactly, a fi re
or explosion may result causing property damage, personal injury or
death. Please read the entire manual before you install and use your
appliance. This heater has not been tested with an unvented gas log
set. To reduce risk of fi re or injury, do not install an unvented gas log
set into the heater.
WARNING
!
ENGLISH
$10.00
INSTALLER:
Leave this manual with the appliance.
CONSUMER:
Retain this manual for future reference.
FOR INDOOR USE ONLY
This wood appliance needs periodic inspection and repair. It is against United States federal regulations to operate this wood
appliance in a manner inconsistent with the operating instructions in this manual.
Wood Stoves ONLY
- At least 14 squares inches (90.3 square centimeters) of outside air
must be admitted to the room or directly to the appliance through a
4” (101.6mm) diameter pipe.
- KEEP THE STOVE TOP TEMPERATURE BELOW 700°F (371°C).
Attempts to achieve heat output rates that exceed design
specifications can result in steel distortion and damage.
IF INSTALLATION + OPERATION, ADD SERIAL
NUMBER LABEL HERE
IF SEPARATE MANUALS, ADD “PLACE
BARCODE LABEL ON THE OWNER’S MANUAL”
U.S. ENVIRONMENTAL PROTECTION AGENCY (E.P.A.) CERTIFIED TO COMPLY WITH 2020
PARTICULATE EMISSION STANDARDS USING CORD WOOD. THIS APPLIANCE HAS BEEN
TESTED BY POLYTESTS AND LISTED BY CSA GROUP TO STANDARDS: ULC S627 AND
UL1482. ASTM E3053-17; ASTM E2515-11 METHODS
ALT-125 AS REFERENCED INTO 40 CFR PART 60 SUBPART AAA.
REFERENCE #: 161746
INSTALLATION AND
OPERATION MANUAL
S20-1
S20-1

W415-2796 / B / 12.19.19
EN
2
safety information
• This appliance is hot when operated and can cause
severe burns if contacted.
• Any changes or alterations to this appliance or its
controls can be dangerous and is prohibited.
• Do not operate appliance before reading and
understanding operating instructions. Failure
to operate appliance according to operating
instructions could cause fi re or injury.
• Before installing this appliance, contact the local
building or fi re authority and follow their guidelines.
• This appliance must be installed by a qualifi ed
installer. Never try to repair or replace any part of the appliance unless instructions are given in this manual.
All other work should be done by a trained technician.
• Risk of burns. The appliance should be turned off and cooled before servicing.
• Do not operate without fully assembling all components. Do not install damaged, incomplete or substitute
components.
• Do not let the appliance become hot enough for any part to glow red.
• Risk of cuts and abrasions. Wear protective gloves, footwear and safety glasses during installation. Sheet
metal edges may be sharp.
• All wiring should be done by a qualifi ed electrician and shall be in compliance with local codes. in the
absence of local codes, use the current CSA22.1 Canadian Electric Code in Canada or the current
National Electric Code ANSI/NFPA No. 70 in the United States.
• If equipped, burning your appliance with the ash dump door ajar creates a fi re hazard that may result in
discolouration to the door, internal damage to the appliance or a house and/or chimney fi re.
• Do not connect this appliance to a chimney fl ue serving another appliance.
• Clothing or other fl ammable material should not be placed on or near the appliance. Objects placed in
front of the appliance must be kept a minimum of 48” (121.9cm) away from the front face of the appliance.
• Due to high temperatures, the appliance should be located out of traffi c and away from furniture and
draperies.
• Even after the appliance is off, it will remain hot for an extended period of time.
• Any safety screen or guard removed for servicing must be replaced prior to operating the appliance.
• Under no circumstances should this appliance be modifi ed.
• This appliance must not be connected to a chimney fl ue pipe servicing a separate solid fuel burning
appliance.
• Do not operate the appliance with the glass door removed, cracked or broken. Replacement of the glass
should be done by a licensed or qualifi ed service person.
• Do not strike or slam shut the appliance glass door.
• Only doors / optional fronts certifi ed with the appliance are to be installed on the appliance.
• If the appliance is not properly installed, a house fi re may result. Do not expose the appliance to the
elements (ex. rain, etc.) and keep the appliance dry at all times. Wet insulation will produce an odour when
the appliance is used.
• The chimney must be sound and free of cracks. Clean your chimney a minimum of twice a year and as
required.
• Children and adults should be alerted to the hazards of high surface temperature and should stay away to
avoid burns or clothing ignition.
• Young children should be carefully supervised when they are in the same room as the appliance.
Toddlers, young children and others may be susceptible to accidental contact burns. A physical barrier
is recommended if there are at risk individuals in the house. To restrict access to an appliance or stove,
install an adjustable safety gate to keep toddlers, young children and other at risk individuals out of the
room and away from hot surfaces.
• Ensure you have incorporated adequate safety measures to protect infants/toddlers from touching hot
surfaces.
• Check with your local hearth specialty dealer for safety screens and hearth guards to protect children from
hot surfaces. These screens and guards must be fastened to the fl oor.
• Keep the packaging material out of reach of children and dispose of the material in a safe manner. As with
all plastic bags, these are not toys and should be kept away from children and infants.
• Do not start a fi re with chemicals or fl uids such as gasoline, engine oil, etc.
HOT GLASS WILL
CAUSE BURNS.
DO NOT TOUCH GLASS
UNTIL COOLED.
NEVER ALLOW CHILDREN
TO TOUCH GLASS.
!
WARNING
!
WARNING

EN
W415-2796 / B / 12.19.19
3
safety information
!
WARNING
• Your appliance requires periodic maintenance and cleaning. Failure to maintain your appliance may lead to smoke
spillage in your home.
• Ashes must be disposed in a metal container with a tight lid and placed on a non-combustible surface well
away from the home or structure until completely cool.
• Ensure clearances to combustibles are maintained when building a mantel or shelves above the appliance.
Elevated temperatures on the wall or in the air above the appliance can cause melting, discolouration or damage
to decorations, a TV or other electronic components.
For wood appliances:
• Lower emissions generally result when burning air dried seasoned hardwoods, as compared to softwoods
or too green or freshly cut hardwoods. Burning wet unseasoned wood can cause excessive creosote
accumulation. When this is ignited it can cause a chimney fi re that may result in a serious house fi re.
• This appliance is designed to burn natural wood only. Do not burn trash or garbage, lawn clippings /
waste, rubber, waste petroleum products, paints or paint thinners / solvents, plastic, materials containing
asbestos, construction debris, railroad ties or treated wood, manure or animal remains, salt water driftwood
or salted materials, unseasoned wood, coal, charcoal, coloured paper, gift wrapping, cardboard, plywood or
particleboard. Burning these materials may result in release of toxic fumes or render the appliance ineffective
and cause smoke.
• Burn wood directly on the fi rebricks. Do not elevate grate or otherwise raise the fi re.
• Do not store wood within appliance installation clearances or within the space required for re-fueling and
ash removal.
• If equipped, the catalyst must be installed and in good working order. It is recommended that the catalyst
is inspected at least three times per heating season.
Add California Prop 65 warning
!
WARNING:
This product can expose you to chemicals including lead and lead compounds,
which are known to the State of California to cause cancer, and chemicals including carbon
monoxide, which are known to the State of California to cause birth defects or other reproduc-
tive harm. For more information, go to www.P65Warnings.ca.gov.

W415-2796 / B / 12.19.19
EN
4
table of contents
1.0 general information 5
1.1 dimensions 5
1.2 specifi cations 6
1.3 general instructions 6
1.4 general information 7
1.5 rating plate information 8
2.0 installation planning 9
2.1 appliance placement 9
2.2 pedestal back plate installation 9
2.3 minimum clearance to combustibles 10
2.4 alcove installation 10
2.5 fl oor protection 11
2.6 outside air 11
3.0 installation 12
3.1 chimney 13
3.1.1 chimney connection 14
3.1.2 adding sections 15
3.1.3 typical through the ceiling 16
3.1.4 typical through the wall 17
3.1.5 typical existing masonry 18
4.0 finishing 19
4.1 door removal 19
4.2 door adjustment 20
4.3 door handle installation 20
4.4 brick and baffl e installation 21
4.5 secondary air tubes 22
4.6 ash lip removal / installation 23
4.7 logo placement 23
5.0 optional installation 24
5.1 blower kit installation 24
5.2 ash disposal kit (ADS20) 25
6.0 operation 26
6.1 optimum burn method 27
6.2 optional blower operation 27
6.3 air control 28
6.4 fi re extinguishers / smoke & carbon
monoxide detectors 28
6.5 fuel 29
6.6 lighting a fi re 29
6.6.1 fl ash fi re 29
6.6.2 extended fi re 30
6.7 smoking 30
7.0 maintenance 31
7.1 ash removal procedures 31
7.1.1 ash removal with ash disposal kit 31
7.2 creosote formation and removal 32
7.3 runaway or chimney fi re 32
7.4 chimney cleaning 32
7.5 door glass replacement 33
7.6 care of glass 34
7.7 door gasket replacement 34
7.8 wood 35
8.0 replacement parts 36
8.1 overview part 1 37
8.2 overview part 2 38
9.0 accessories 39
10.0 troubleshooting 40
11.0 warranty 41
The information throughout this manual is believed to be correct at the time of printing. Wolf Steel Ltd.
reserves the right to change or modify any information within this manual at any time without notice. Changes,
other than editorial, are denoted by a vertical line in the margin.
note:

EN
W415-2796 / B / 12.19.19
5
dimensions
1.0 general information
1.1 dimensions
20 1/2”
(521mm)
22”
(559mm)
34 1/4”
(870mm)
26”
(660mm)
6 1/2”
(165mm)
Ø 6”
(152mm)
13”
(330mm)
22”
(558mm)
24 1/2”
(622mm)
9 3/4”
(248mm)
15 5/8”
(398mm)
5”
(127mm)
TOP VIEW FRONT VIEW RIGHT SIDE VIEW

W415-2796 / B / 12.19.19
EN
6
general information
• Before beginning your installation, consult with your local building code agency or fi re offi cials and insurance
representative to ensure compliance.
• Non-toxic smoke will be emitted during the paint curing process, to help dissipate the smoke open a window
near the appliance.
• Remove any dust or debris off the top of the appliance before fi ring the appliance as the paint will become
soft as the appliance heats up and will harden as the appliance cures. To cure the paint on your appliance
burn your appliance moderately hot during the fi rst few fi res.
• To keep the gasket from sticking to the appliance as the paint is curing, periodically open the door every 5-10
minutes.
• For the fi rst two weeks use generous amounts of fuel and burn the appliance with the damper wide open for
an hour as the appliance goes through a process of eliminating moisture in the steel and fi rebricks. The initial
heat output will be reduced while the moisture is being drawn from the appliance and it will be necessary
to build several hot fi res to remove this moisture. DURING THIS PROCESS DO NOT OVERFIRE THE
APPLIANCE. REDUCE THE AMOUNT OF AIR COMING INTO THE APPLIANCE IF THE APPLIANCE
OR CHIMNEY BECOMES RED.
!
WARNING
• All wiring should be done by a qualifi ed electrician and shall be in compliance with local codes. In the
absence of local codes, use the current CSA C22.1 Canadian Electric Code (in Canada) or the ANSI / NFPA
N
o
70 National Electric Code in the United States.
• Burning your appliance with the ash well open or the ash door ajar creates a fi re hazard and may cause
internal damage to the appliance or a house and/or chimney fi re.
• Do not connect this appliance to a chimney fl ue serving another appliance. Do not connect to any air
distribution duct or system.
• Provide adequate clearance for servicing and operating the appliance.
• Provide adequate ventilation.
• Never obstruct the front opening of the appliance.
• Objects placed in front of the appliance must be kept a minimum of 48” (121.9cm) from the front face of the
appliance.
• Do not install in a mobile home.
1.2 specifi cations
Specifi cations
Emissions 2.25 grams / hour
Effi ciency 72%
Chamber (D.W.H) 14 5/8" x 20 7/8" x 11 5/8"
(372mm x 530mm x 295mm)
Capacity 1.9 cubic feet (0.05 cubic meters)
Viewing Area 153 in² (987cm²)
Approx. area heated** 800-1800 square feet (74-167m²)
Maximum heat output*** 65,000 BTU /Hr
Heat output* 12,944 - 54,127 BTU /Hr
Duration low fi re** 8 hours
Weight w/o bricks 210 lbs (95kg)
Weight of bricks 60 lbs (27kg)
Ideal wood length 16" (406mm)
Minimum Stack Height **** 15 feet (4.5m)
Effi ciency Standard B415.1-10
* As tested using test method
ALT-125.
** Figures will vary considerably
with individual conditions.
*** Wolf Steel Ltd. estimated
realistic BTU/hr with hardwood
logs and regular refueling.
**** Required in order to achieve
proper draft.
1.3 general instructions

EN
W415-2796 / B / 12.19.19
7
general information
This appliance was specifi cally designed over many months
of research to meet the 2020 U.S.A. EPA particulate emission
standards and has been extensively tested in Canadian
laboratories. This sytem is the most effi cient, simple and trouble-
free we know and works as follows:
Secondary air from the rear opening travels up the back in the
secondary air housing to the manifold located at the top and
shoots out laterally to oxidize the gases below the smoke exit.
The lower combustion chamber is lined with high temperature
fi rebricks on 2 sides, the back and across the bottom, with a layer
of fi bre baffl es at the top to maintain a high temperature in the
combustion chamber so that gases mixing with the preheated
air from the secondary air manifold tube are easily ignited and
burned. The appliance sides and back are shielded to direct the
heat upwards and forwards into the room.
Be sure to provide suffi cient combustion air. There are many other
appliances in your home competing for air such as: a kitchen range hood, forced air heating devices, clothes dryer or a
bathroom exhaust blower.
After extended periods of non-operation such as following a vacation or a warm weather season, the appliance may
emit a slight odour for a few hours. This is caused by dust particles on the fi rebox burning off. Open a window to
suffi ciently ventilate the room.
If you experience smoking problems, you may need to open a door, a window or otherwise provide some method
of supplying combustion air to the appliance.
Do not use makeshift compromises during installation. Do not block or restrict air, grille, or louvre openings. Do
not add a hood. Burning your appliance with the door open or ajar creates a fi re hazard that may result in a house
and/or chimney fi re.
All venting connections must be in compliance with the chimney manufacturer’s installation instructions.
Clearances referred to throughout this manual are the minimum requirements.
Your appliance must be installed in accordance with all national and local building code standards and the
standard of Chimney and Appliances, Vents and Solid Fuel Burning Appliances NFPA #211. Consult the authority
having jurisdiction (such as municipal building department, fi re department, fi re prevention bureau, etc.) to
determine the need to obtain a permit. If you are in doubt about the proper installation for your situation, contact
your dealer or local building or fi re offi cial. The manufacturer does not guarantee that this appliance and its options
will completely heat your entire home.
Expansion / contraction noises during heating up and cooling
down cycles are normal and to be expected.
It is recommended that in all cases, the appliance be secured
to the fl oor.
1.4 general information
!
WARNING
• Do not operate this appliance without the pedestal installed.
AIR INLET PATH
EXHAUST PATH

W415-2796 / B / 12.19.19
EN
8
general information
W385-4531 / A
S20
UL1482 - 2011 / ULC S627 - 00
MODEL / MODÈLE: S20
POUR INSTALLATION ET UTILISATION CONFORMÉMENT AUX INSTRUCTIONS DE WOLF
STEEL LTÉE. RENSEIGNEZ-VOUS AUPRÈS DES AUTORITÉS LOCALES DU BÂTIMENT
OU DU SERVICE DES INCENDIES AU SUJET DES RESTRICTIONS ET DES INSPECTIONS
D’INSTALLATION DANS VOTRE RÉGION.
HAUTEUR DE PLAFOND MINIMAL 7” (2,13M) EN UTILISANT UN TUYAU DE
RACCORDEMENT À PAROI SIMPLE.
BASE DE PROTECTION/PROTECTION DU PLANCHER COMBUSTIBLE: SI INSTALLÉ
SUR UN PLANCHER COMBUSTIBLE, L’APPAREIL DOIT ÊTRE PLACÉ SUR UNE PLAQUE
PROTECTRICE INCOMBUSTIBLE S’ÉTENDANT SUR 18” (455mm) (CANADA) / 16”
(406MM) (É.U.) À L’AVANT ET 8” (205MM) À L’ARRIÈRE ET SUR LES CÔTÉS.
TYPE DE CHEMINÉE: CHEMINÉE RÉSIDENTIELLE DE 6" DE DIAMÈTRE (152MM)
HOMOLOGUÉE (UL 103HT).
RACCORD DE CHEMINÉE: DIAMÈTRE DE 6” (152MM) D’ACIER DE CALIBRE 24
MINIMUM. 18” (455MM) DE DÉGAGEMENT MINIMAL ENTRE LE RACCORD HORIZONTAL
ET LE PLAFOND.
NE RIEN ENTREPOSER SOUS LE CHAUFFAGE.
DES MÉTHODES SPÉCIALES SONT REQUISES LORSQUE UNE CHEMINÉE TRAVERSE
UN MUR OU UN PLAFOND. VOIR LES INSTRUCTIONS ET LES CODES DU BÂTIMENT.
NE PAS RACCORDER À LA CHEMINÉE D’UN AUTRE APPAREIL.
AVERTISSEMENT: POUR USAGE AVEC LE BOIS SEULEMENT. NE BRÛLEZ PAS
AUCUNE AUTRE TYPE DE COMBUSTIBLE. N’UTILISEZ PAS DE CHENET OU NE
SURÉLEVEZ PAS LE BOIS. PRÉPAREZ LE FEU DIRECTEMENT SUR L’ÂTRE.
AVERTISSEMENT: RISQUE D’ÉCHAPPEMENT DE FUMÉE. TENIR LA PORTE FERMÉE
LORSQUE LE POÊLE FONCTIONNE. REMPLACEZ LA VITRE PAR UNE VITRE EN
CÉRAMIQUE SEULEMENT. NE SURCHAUFFEZ PAS L’APPAREIL. SI L’APPAREIL OU LES
RACCORDS ROUGEOIENT, L’APPAREIL SURCHAUFFÉE. INSPECTEZ ET NETTOYEZ LA
CHEMINÉE FRÉQUEMMENT. DANS CERTAINES CONDITIONS, DES DÉPÔTS DE
CRÉOSOTE PEUVENT SE FORMER RAPIDEMENT.
SOUFFLERIE OPTIONNELLE: NEP70, 115V, 60HZ, 0,82A. TENEZ LE CORDON
ÉLECTRIQUE LOIN DE L’APPAREIL.
DANGER: RISQUE DE SECOUSSE ÉLECTRIQUE. DÉBRANCHEZ AVANT DE PROCÉDER
À L’ENTRETIEN.
INSTALL AND USE ONLY IN ACCORDANCE WITH WOLF STEEL LTD.’S
INSTRUCTIONS. CONTACT LOCAL BUILDING OR FIRE OFFICIALS ABOUT
RESTRICTIONS AND INSTALLATION INSPECTION IN YOUR AREA.
MINIMUM CEILING HEIGHT: 7FT (2.13M) USING A SINGLE WALL
CONNECTOR.
HEARTH EXTENSION / COMBUSTIBLE FLOOR PROTECTION: IF
INSTALLED ON A COMBUSTIBLE FLOOR, UNIT MUST BE PLACED ON A
NON-COMBUSTIBLE FLOOR PROTECTOR EXTENDING 18” (455MM)
(CANADA) / 16” (406MM) (U.S.A.) IN FRONT AND 8” (205MM) TO THE SIDES AND
BACK.
CHIMNEY TYPE: MINIMUM 6” (152MM) DIAMETER LISTED (UL 103HT)
RESIDENTIAL CHIMNEY.
CHIMNEY CONNECTOR: 6” (152MM) DIAMETER MINIMUM 24 GAUGE
STEEL MINIMUM CLEARANCE FROM HORIZONTAL CONNECTOR AND
CEILING 18” (455MM).
DO NOT OBSTRUCT SPACE UNDER HEATER.
SPECIAL METHODS ARE REQUIRED WHEN PASSING A CHIMNEY
THROUGH A WALL OR CEILING. SEE INSTRUCTIONS AND BUILDING
CODES.
DO NOT CONNECT THIS UNIT TO A CHIMNEY FLUE SERVING ANOTHER
APPLIANCE.
WARNING: FOR USE WITH SOLID WOOD FUEL ONLY. DO NOT BURN ANY
OTHER TYPE OF FUEL. DO NOT USE GRATE OR ELEVATE FIRE. BUILD
WOOD FIRE DIRECTLY ON HEARTH.
WARNING: RISK OF SMOKE SPILLAGE. OPERATE ONLY WITH DOOR
FULLY CLOSED. REPLACE GLASS ONLY WITH CERAMIC GLASS.
DO NOT OVERFIRE. IF HEATER OR CHIMNEY CONNECTORS GLOW, YOU
ARE OVERFIRING. INSPECT AND CLEAN CHIMNEY FREQUENTLY. UNDER
CERTAIN CONDITIONS OF USE CREOSOTE BUILD-UP MAY OCCUR RAPIDLY.
OPTIONAL BLOWER KIT: NEP70, 115V, 60HZ, 0.82AMP. ROUTE CORD
AWAY FROM UNIT.
DANGER: RISK OF ELECTRICAL SHOCK. DISCONNECT POWER BEFORE
SERVICING UNIT.
CAUTION:
ATTENTION:
HOT WHILE IN OPERATION. DO NOT TOUCH. KEEP CHILDREN, CLOTHING AND
FURNITURE AWAY. CONTACT MAY CAUSE SKIN BURNS. SEE NAMEPLATE AND
INSTRUCTIONS.
QUAND L’APPAREIL FONCTIONNE, LA SURFACE DEVIENT CHAUDE. NE PAS TOUCHER.
TENIR LES ENFANTS, LES VÊTEMENTS ET LES MEUBLES À L’ÉCART. LE CONTACT PEUT
CAUSER DES BRÛLURES À LA PEAU. VOIR LA PLAQUE D’HOMOLOGATION ET LES
INSTRUCTIONS.
WOLF STEEL USA
103 MILLER DRIVE, CRITTENDEN, KY
401030 USA
NAC GUANGZHOU P.R.C.
NO.69 HEFENG ROAD, GUANGZHOU,CHINA
MANUFACTURE DATE: / DATE DE FABRICATION:
YEAR/ANNÉE: 2019 2020 2021 2022
MONTH/MOIS:
2023 2024
2 43 65 87 109 12111
U.S. ENVIRONMENTAL PROTECTION AGENCY Certified to comply with 2020
particulate emission standards using cordwood. Certifié conforme à la norme
d’émanation de particles de 2020 en utilisant bois de corde.
40 CFR Part 60,
Subpart AAA
2.25 Grams Per Hour / 2020 Cordwood / 2,25 Grammes par heure
/ Bois de Corde 2020. Efficiency / Efficacité: 72%
LISTED SOLID FUEL BURNING SPACE HEATER /
POÊLE À COMBUSTIBLE SOLIDE HOMOLOGUÉ.
TESTED TO: / TESTÉ SELON:
Sidewall / mur de côté (A) 12” (30.5cm)
Sidewall to flue / mur de côté à la buse (B)
Backwall / mur arrière (C) 11 1/2” (29.2cm) 9 1/2” (24.1cm)
Backwall to flue / mur arrière à la buse (D) 15” (38.1cm) 12 1/2" (31.8cm)
Corner / coin (E) 11" (27.9cm) 7" (17.8cm)
Ceiling / plafond (F) 84" (213.4cm)
Clearances can be reduced with shielding acceptable to local
authorities. Reduced installation must comply with NFPA 211 or
CAN/CSA-B365. / Il est possible de réduire les dégagements à
l’aide d’un protecteur conforme aux normes des autorités locales.
Une installation réduite doit être conforme aux normes NFPA 211
ou au CAN/CSA B365.
PARALLEL & CORNER /
PARALLÈLE & COIN
13” (33cm)
22 7/8” (58.1cm) 21 1/2” (54.6cm)
5 1/2" (14cm)
8 1/2" (21.6cm)
SINGLE WALL CONNECTOR /
TUYAU DE RACCORDEMENT À
PAROI SIMPLE
DOUBLE WALL CONNECTOR /
TUYAU DE RACCORDEMENT À
PAROI DOUBLE
B
A
CD
E
E
BACK WALL /
MUR ARRIÈRE
BACK WALL /
MUR ARRIÈRE
ALCOVE / ALCÔVE FLOOR
PROTECTION /
PROTECTION DU
PLANCHER
SIDE WALL /
MUR DE CÔTÉ
SIDE WALL /
MUR DE CÔTÉ
48” (1219.2mm)
MAX
K J
L
MM
N
ALCOVE / ALCÔVE
Ceiling / plafond (G) N/A 75” (190.5cm)
MINIMUM FLOOR PROTECTION / PROTECTION MINIMAL DU PLANCHER
FRONT / DEVANT (L) SIDES / CÔTÉS (M) BACK / ARRIÈRE (N)
CANADA
USA / É-U
18” (45.7cm)
16” (40.6cm)
8” (203mm)
8” (203mm)
H
I
Sidewall / sur de côté (H)
Sidewall to flue / mur de côté à la buse (I)
Backwall / mur arrière (J)
Backwall to flue / mur arrière à la buse (K)
19" (48.3cm)
28 7/8" (73.3cm)
N/A 12 1/2" (31.8cm)
16" (40.6cm)
THIS WOOD HEATER NEEDS PERIODIC INSPECTION AND REPAIR FOR PROPER OPERATION. CONSULT THE OWNER’S MANUAL FOR FURTHER INFORMATION.
IT IS AGAINST FEDERAL REGULATIONS TO OPERATE THIS WOOD HEATER IN A MANNER INCONSISTENT WITH THE OPERATING INSTRUCTIONS IN THE
OWNER’S MANUAL. / CE POÊLE À BOIS DOIT ÊTRE INSPECTÉ ET RÉPARÉ PÉRIODIQUEMENT POUR UN FONCtIONNEMENT CORRECT. CONSULTEZ LE MANUEL
DU PROPRIÉTAIRE POUR PLUS D’INFORMATIONS. IL EST CONTRE LES RÈGLEMENTS FÉDÉRAUX POUR FAIRE FONCTIONNER CE POÊLE À BOIS D’UNE
MANIÈRE INCOMPATIBLE AVEC LES INSTRUCTIONS DE FONCTIONNEMENT DANS LE MANUEL DU PROPRIÉTAIRE.
REFERENCE #: 161746
WOLF STEEL LTD.
24 NAPOLEON ROAD, BARRIE, ON
L4M 0G8 CANADA
N/A
N/A
N/A
DOUBLE WALL CONNECTOR +
LOW CLEARANCE COMBUSTION KIT /
TUYAU DE RACCORDEMENT À PAROI
DOUBLE + ENSEMBLE DE
COMBUSTION À DÉGAGEMENT BAS *
* Only applicable with the use of low clearance combustion kit
RCHS20. See “accessories” section of your installation manual
for more information. / Seulement applicable avec l’utilisation de
l’ensemble de combustion à dégagement bas RCHS20. Voir la
section « accessoires » dans votre manuel d’installation pour
plus d’information.
1.5 rating plate information
SAMPLE
US
S
E
PLACÉ SU
LACÉ S
55mm) (CANADA
mm) (CANAD
T SUR LES CÔTÉS.
SUR LES CÔT
E 6" DE DIAMÈTRE (152MM
6" DE DIAMÈT
152MM) D’ACIER DE CALIBRE 24
52MM) D’ACIER DE CALIBRE 24
MINIMAL ENTRE LE RACCORD HORIZONTAL
NIMAL ENTRE LE RACCORD HORIZO
UFFAGE.
REQUISES LORSQUE UNE CHEMINÉE TRAVERSE
ORSQUE UNE CHEMINÉE TRAVERSE
LES INSTRUCTIONS ET LES CODES DU BÂTIMENT.
S ET LES CODES DU BÂTIMENT.
HEMINÉE D’UN AUTRE APPAREIL.
PAREIL.
USAGE AVEC LE BOIS SEULEMENT. NE BRÛLEZ PAS
ENT. NE BRÛLEZ PAS
DE COMBUSTIBLE. N’UTILISEZ PAS DE CHENET OU NE
E COMBUSTIBLE. N’UTILISEZ PAS DE CHENET OU NE
BOIS. PRÉPAREZ LE FEU DIRECTEMENT SUR L’ÂTRE.
OIS. PRÉPAREZ LE FEU DIRECTEMENT SUR L’ÂTRE.
T:
RISQUE D’ÉCHAPPEMENT DE FUMÉE. TENIR LA PORTE FERM
RISQUE D’ÉCHAPPEMENT DE FUMÉE. TENIR LA PORTE FERM
POÊLE FONCTIONNE. REMPLACEZ LA VITRE PAR UNE VITRE EN
FONCTIONNE. REMPLACEZ LA VITRE PAR UNE VITRE EN
E SEULEMENT. NE SURCHAUFFEZ PAS L’APPAREIL. SI L’APPARE
NT. NE SURCHAUFFEZ PAS L’APPAREIL. SI L’APPAR
RDS ROUGEOIENT, L’APPAREIL SURCHAUFFÉE. INSPECTEZ ET N
ROUGEOIENT, L’APPAREIL SURCHAUFFÉE. INSPECTEZ ET
MINÉE FRÉQUEMMENT. DANS CERTAINES CONDITIONS, DES DÉP
NÉE FRÉQUEMMENT. DANS CERTAINES CONDITIONS, DES DÉ
ÉOSOTE PEUVENT SE FORMER RAPIDEMENT.
OSOTE PEUVENT SE FORMER RAPIDEMENT
SOUFFLERIE OPTIONNELLE:
OUFFLERIE OPTIONNELL
NEP70, 115V, 60HZ, 0,82A. TENE
70, 115V, 60HZ, 0,82A. TEN
PL
É
LECTRIQUE LOIN DE L’APPAREIL.
ÉLECTRIQUE LOIN DE L’APPA
DAN
G
ER
:
DANGE
RISQUE DE SECOUSSE ÉLECTRIQUE. DÉBRANC
DE SECOUSSE ÉLECTRIQUE. DÉBRAN
P
À L’ENTRETIEN
.
À L’EN
SAMP
ORE
RE
YEAR
YEA
A
AM
A
A
A
M
A
A
AM
A
A
A
A
M
A
A
AM
A
A
A
A
M
M
M
M
M
M
M
M
A
A
AM
A
M
A
A
A
M
M
M
M
M
A
A
AM
A
M
A
A
A
M
M
M
M
M
A
A
AM
A
M
A
A
A
M
M
à la buse (B)
re (C)
(C)
11 1/2” (29.2cm
)
(29.2cm)
9 1/
9
mur arrière à la buse (D)
r arrière à la buse (D)
1
5”
(
38.1cm
)
m)
n (E)
1
1"
(
27.9cm
)
11
/ plafond (F)
AM
13”
(
33cm
)13” (33cm)
22 7/8” (58.1cm
)
7/8” (58.1cm)
SINGLE WALL CONNECTOR /
TUYAU DE RACCORDEMENT À
PAROI SIMPLE
DOUBLE WALL CONNECTOR
TUYAU DE RACCORDEMEN
PAROI DOUBLE
M
M
M
M
M
M
M
M
M
M
M
M
M
M
M
M
M
M
M
M
MP
MP
MP
MP
M
M
M
M
E
AL
CO
VE
/
AL
CÔ
V
E
SIDE WALL
/
SID
MUR DE CÔTÉ
P
P
P
P
P
P
P
P
P
P
P
K
P
MP
P
P
MP
MP
MP
P
MP
P
MP
MP
MP
MP
P
MP
MP
M
P
P
MP
MP
MP
SAM
A
A
AM
A
M
ALCOVE / ALCÔVE
SA
Ceiling / plafond (G)
SA
N/
A
N/A
SA
MINIMUM FLOOR PROTEC
SA
SA
S
FRONT / DEV
FRONT / DE
SA
C
ANADA
CANADA
US
A
/
É
-
U
USA
18” (45.7
18
16” (4
16
SA
Sidewall / sur de côté (H
)
Sidewall / su
SA
SA
S
idewall to flue / mur de côté à la buse (I
)Sidewall to flue / mur de côté à la buse (I)
SA
SA
B
ackwall / mur arrière
(
J
)
Backwall /
SA
SA
Backwall to flue
/
mur arri
è
re
à
la buse
(
K
)
ue / mur arrière à la buse (K)
SA
N/A
SAMPLE
N/A
N
/
A
This illustration is for reference only. Refer to
the rating plate on the appliance for accurate
information.
The rating plate must remain with the
appliance at all times. It must not be
removed.
note:

EN
W415-2796 / B / 12.19.19
9
installation planning
2.0 installation planning
2.1 appliance placement
2.2 pedestal back plate installation
1. Place the back plate in position, ensuring the holes in the back plate align with the holes in the appliance
(Fig. 2-1).
2. Install two screws (supplied) to secure the back plate in position (Fig. 2-2).
Back Plate
Fig. 2-1
Fig. 2-2
We recommend having your Napoleon wood burning appliance installed by a qualifi ed technician. However,
should you choose to install the appliance yourself, it is extremely important that you follow all installation
instructions for the appliance, the chimney and connector if applicable, as well as local building codes. At the very
least, draw a detailed plan of your installation, including clearance dimensions to combustibles, and have your
authorized dealer review them to confi rm that they conform to the relative installation parameters.
When positioning the appliance, it may be necessary to adjust its position to prevent the chimney/vent system
from intersecting with a framing member and to meet the minimum combustible clearance requirements. Its
location should also avoid the potential for drapes or doors to swing within 48” (122cm) in front of the appliance
to prevent a fi re hazard.
note:

W415-2796 / B / 12.19.19
EN
10
installation planning
BACK WALL
B
SIDE WALL
A
BACK WALL
C
SIDE WALL
F
D
E
E
PARALLEL &
CORNER
SINGLE WALL
CONNECTOR
DOUBLE WALL
CONNECTOR
DOUBLE WALL
CONNECTOR +
DOUBLE BACK SHIELD
AND TOP SHIELD *
Sidewall (A) 13” (33cm) 12” (30.5cm)
Sidewall to fl ue (B) 22 7/8” (58.1cm) 21 1/2” (54.6cm)
Backwall (C) 11 1/2” (29.2cm) 9 1/2” (24.1cm) 5 1/2” (14cm)
Backwall to fl ue (D) 15” (38.1cm) 12 1/2” (31.8cm) 8 1/2” (21.6cm)
Corner (E) 11" (27.9cm) 7" (17.8cm)
Ceiling (F) 84" (213.4cm)
Clearances can be reduced with shielding acceptable to local authorities. Reduced installation must comply with
NFPA 211 or CAN/CSA-B365.
ALCOVE
PARALLEL & CORNER SINGLE WALL CONNECTOR DOUBLE WALL CONNECTOR
Ceiling (G)
N/A
75" (190.5cm)
Sidewall (H) 19” (48.3cm)
Sidewall to fl ue (I) 28 7/8” (73.3cm)
Backwall (J) 12 1/2” (31.8cm)
Backwall to fl ue (K) 16” (40.6cm)
19"
(48.3cm)
28
7
/
8
"
(733.4mm)
ALCOVE
48” (122cm)
MAX
A B
Your appliance may be installed using a listed
double wall connector (such as Security DL6 in
Canada, the Simpson Duravent Plus DVL in the
USA, or an equivalent double wall connector) into
an alcove having a depth of no more than 4 feet
(1.2m) and a height of at least 6’3" (1.8m x 76mm).
The minimum clearances are as shown.
F
2.3 minimum clearance to combustibles
2.4 alcove installation
!
WARNING
• Do not install into any area having less than 7 feet (2.1m) (ceiling to appliance bottom, excluding hearth height).
G
KJ
H
I
*
Only applicable with the use of low clearance combustion kit RCHS20. See “accessories” section for more
information.
note:

EN
W415-2796 / B / 12.19.19
11
installation planning
2.5 fl oor protection
If the appliance is to be installed on top of a combustible fl oor, it must be placed on an approved non-combustible
hearth pad, that extends 8" (203mm) beyond the appliance sides and back, and 18" (45.7cm) in Canada / 16”
(40.6cm) in the USA to the front. The reduced clearance from the back of the appliance may result in the appliance
pad terminating shorter than 8" (203mm) beyond the appliance.
Refer to local building codes for suitable fl oor protection materials.
K
J
J
I
MINIMUM FLOOR PROTECTION
FRONT (L) SIDES (M) BACK (N)
CANADA 18" (45.7cm) 8" (203mm)
USA 16" (40.6cm) 8" (203mm)
2.6 outside air
The following are signs that fresh air may be required for the appliance to better function:
• When there is combustion present, wood burns poorly, smoke spills, back-draft takes place, and your
chimney does not draw steadily.
• In the winter, there is too much condensation on the windows.
• Opening a window seems to alleviate the above symptoms.
• A ventilation system is installed in the house.
• Other devices are present that exhaust house air.
• The house has tight fi tting windows and/or is equipped with a well-sealed vapour barrier.
Systems such as HRV’s are designed to bring fresh air into your home and will resolve these related performance
issues with your appliance.
If outside air is brought directly to the appliance, a damper allowing 100% closure shall be used (not supplied). The
air inlet must prevent material from dropping into the inlet and also prevent rodents from entering from the outside
(a wire mesh having openings not larger than 1/4” by 1/4” [6.4mm by 6.4mm] is suffi cient).
Floor protection is required for spark and ash shielding, but not for limiting fl oor temperatures from the radiant
heat of the appliance. The appliance was designed and safety-tested so that without any protection, the fl oor
would not overheat.
note:
If a section of horizontal chimney connector is used, fl oor protection is required under
the chimney connector and 2” (51mm) beyond each side.
note:
L
MM
N

W415-2796 / B / 12.19.19
EN
12
3.0 installation
!
WARNING
• Wear gloves, protective footwear and safety glasses for protection.
• Carefully follow the instructions for assembly of the pipe and other parts needed to install the appliance.
Failure to do so may result in a fi re, especially if combustibles are too close to the appliance or chimney and air
spacers are blocked, preventing the free movement of cooling air.
• Do not draw outside air from garage spaces. Exhaust products of gasoline engines are hazardous. Do not
install outside air ducts such that the air may be drawn from attic spaces, basements or above the roofi ng
where other heating appliances or fans and chimneys exhaust or utilize air. These precautions will reduce the
possibility of appliance smoking or air fl ow reversal. The outside air inlet must remain clear of leaves, debris, ice
and/or snow. It must be unrestricted while appliance is in use to prevent room air starvation which can cause
smoke spillage and an inability to maintain a fi re. Smoke spillage can also set off smoke alarms.
• Negative pressure within your home may inadvertently affect your appliance.
• To prevent contact with sagging or loose insulation, the appliance must not be installed against vapour barriers
or exposed insulation. Localized overheating could occur and a fi re could result.
• Do not use makeshift compromises during installation. Do not block or restrict air, grille or louvre openings. Do
not add a hood.
• To prevent personal injury, keep hand tools in good condition, sharpen cutting edges and make sure tool
handles are secure.
• Always maintain the minimum air space required in the enclosure to prevent fi res.
• Check with local building offi cials for any permits required for installation of this appliance and notify your
insurance company prior to proceeding.

EN
W415-2796 / B / 12.19.19
13
installation
3.1 chimney
Your appliance may be connected to a factory built or masonry chimney. If you are using a factory built chimney,
it must comply with ULCS629 (Canada) or UL103 (USA) standards. It must therefore be a 6" (152mm) HT Type
(2100°F) chimney. It is extremely important that it be installed according to the manufacturer’s specifi cations.
The manufacturer’s installation instructions and specifi ed clearances should always be followed in accordance with
local and national codes. In Canada the CSA B365 and the CSA C22.1 installation codes are to be followed. In
the USA the ANSI NFPA 70 and ANSI NFPA 211 installation codes are to be followed.
Chimney and chimney connector must be in good condition and kept clean.
!
WARNING
• Never install a single wall slip section or smoke pipe in a chase structure. The higher temperature of this single
wall pipe may radiate suffi cient heat to combustible chase materials to cause a fi re.
• Do not connect this appliance to a chimney system serving another appliance.
• To avoid danger of fi re, all instructions must be strictly followed, including the provision of air space clearance
between chimney system and enclosure. To protect against the effects of corrosion on those parts exposed to
the weather, we recommend that the chase top be painted with a rust-resistant paint.
• Do not fi ll any framed space around the chimney with insulation or any other material. Insulation placed in this
area could cause adjacent combustibles to overheat.
• Maintain a minimum 2” (51mm) air clearance to all parts of the chimney system at all times (this excludes the
chimney connection). Failure to maintain this 2” (51mm) air clearance will cause a structure fi re. Never fi ll this
space with any type of material.
• Detailed instructions for installation of the chase top, storm collar and termination cap are packaged with these
parts.
• Do not cut rafters or ceiling joists without fi rst consulting a building offi cial to ensure structural integrity is not
compromised.
• Firestop spacers must be used whenever the chimney penetrates a ceiling/fl oor area.
• The total horizontal vent length should not exceed 40% of the chimney height above the appliance all horizontal
smoke pipe must slope slightly upwards a minimum of 1/4” (6.4mm) per foot and all connections must be tight
and secured by three sheet metal screws equally spaced. An uninsulated smoke pipe shall not pass through
an attic, roof space, closet or similar concealed space, or through a fl oor, ceiling, wall or partition, or any
combustible constructions.
• Do not use any makeshift materials during installation.

W415-2796 / B / 12.19.19
EN
14
installation
3.1.1 chimney connection
Your chimney connector and chimney must have the same diameter as the appliance’s exhaust fl ue outlet. The
appliance pipe must be made of aluminized or cold roll steel with a minimum 24 gauge (0.6mm) thickness. It is
strictly forbidden to use galvanized steel.
A 6” (152.4mm) diameter single or double wall chimney connector, used to connect the appliance to the chimney,
must be installed with the crimped end toward the appliance. This will ensure that the moisture which condenses
from the burning wood will fl ow back into the fi re chamber. Each joint in the chimney connector must be secured
with at least three sheet metal screws, equally spaced around the circumference.
For installation of your chimney connector, the following recommendations may be useful:
• The chimney connector must be short and straight. For optimum performance, it is recommended that all
horizontal runs have a minimum 1/4” (6mm) rise per foot (0.3m), with the higher end of the section toward the
chimney. For safe and proper operation of the appliance, see the “installation” section.
• To ensure a good draft, the total horizontal length of the connector should never exceed 8’ (2.4m) to 10’
(3.1m). In the case of vertical installation, the total length of the connector can be longer and connected
without problem to the chimney at the ceiling level.
• There should never be more than two 90° elbows in the entire connector and chimney system. Never start
with a 90° elbow. Always go up vertically for at least 2 feet (0.6m) from the flue collar before using a 90°
elbow.
• The connector must not pass through any combustible material, nor may it pass through a concealed
space (such as an attic, roof space, or closet). If passing through a wall, ceiling or into a masonry chimney,
use either chimney components listed for that specifi c use, or means acceptable to local authorities having
jurisdiction over the installation.
This appliance must be connected to:
A. A chimney complying with the requirements for Type HT
chimneys in the Standard for Chimneys, Factory-Built,
Residential Type and Building Heating Appliance
OR
B. A code-approved masonry chimney with a fl ue liner. Vent
the stove into a masonry chimney or an approved, insulated
solid-fuel stainless-steel chimney with as short and straight a
length of 6” (152mm) diameter chimney connector as possible.
Connection to a masonry thimble cemented in place.
TOWARD
APPLIANCE
FLUE GAS
DIRECTION
MALE END OF
CONNECTOR
OR CHIMNEY
PIPE

EN
W415-2796 / B / 12.19.19
15
installation
3.1.2 adding sections
An insulated stainless steel
chimney must be supported
at the ceiling or roof and its
installation must comply with
its manufacturer’s instructions.
Add chimney sections, according to the manufacturer’s installation instructions. If the chimney system passes
through an attic space, a rafter radiation shield or attic insulation shield is required. The chimney must extend at
least 3ft (0.9m) above its point of contact with the roof and at least 2ft (0.6m) higher than any wall, roof or building
within 10ft (3.1m). If the chimney extends more than 5ft (1.5m) above the roof, it must be secured using a roof
brace or guide wires. A raincap must be installed to avoid internal damage and corrosion.
3 FT (1m)
MIN
3 FT (1m)
MIN
10 FT (3m)
OR MORE
FLAT ROOF WALL
RIDGE
LESS THAN
10FT (3m)
2 FT (0.6m) MIN 3 FT (1m)
MIN
2 FT (0.6m)
MIN
LESS THAN
10FT (3m)
3 FT (1m)
MIN 2 FT (0.6m)
MIN
10 FT (3m)
TO NEAREST
ROOFLINE
Floor, Ceiling Joist
LIVING SPACE
Framed
Enclosure
2” (51mm)
clearance from
chimney to
combustible wall
Chimney Lengths
Ceiling Joist
Chimney must be
totally enclosed
when passing
through living space
with a minimum 2”
(51mm) clearance
to combustibles.
ATTIC SPACE

W415-2796 / B / 12.19.19
EN
16
installation
3.1.3 typical through the ceiling
A. Move the stove into position with the flue centered, midpoint between two
joists to prevent having to cut them. Use a plumb bob to line up the center.
B. Cut and frame an opening in the ceiling to provide a 2” (50.8mm)
clearance between the outside of the chimney and any combustible
material. Do not fill this space with any type of material.
Nail headers between the joist for extra support.
Firestop spacers must be placed on the bottom
of each framed opening in any floor or ceiling
that the chimney passes through. If your
chimney system is enclosed within the attic
area, a rafter radiation shield is required.
C. Hold a plumb bob from the underside of the
roof to determine where the opening in the
roof should be. Cut and frame the roof opening
to maintain proper 2” (50.8mm) clearances.
HEADERS
FIRESTOP SPACER -
UNDERSIDE OF JOIST
FLOOR
PROTECTOR
ROOF
FLASHING
STORM
COLLAR
TERMINAL
COMBUSTIBLE
WALL
MAINTAIN
2” (50.8mm)
CLEARANCE
CHIMNEY
CONNECTOR
CEILING
SUPPORT
LISTED CHIMNEY
INSULATION
CEILING
SUPPORT
LISTED
CHIMNEY SPECIFIED
CLEARANCE
TO STOVE
note:
The chimney must be supported at the ceiling or
roof so that its weight does not rest on the appliance
and must comply with its manufacturer’s instructions.

EN
W415-2796 / B / 12.19.19
17
installation
3.1.4 typical through the wall
If possible, design the installation so that the connector does not pass through a combustible wall. If during
your installation you must pass through a combustible wall, check with your building inspector before you
begin. Also check with the chimney connector manufacturer for any specific requirements.
Consult with your dealer regarding special connection components available for use for wall pass-throughs.
Use only parts that have been tested and listed for use in a wall pass-through.
FLOOR
PROTECTOR
ROOF
FLASHING
STORM
COLLAR
TERMINAL
COMBUSTIBLE
WALL
MAINTAIN 2”
(50.8mm) CLEARANCE
THROUGH EAVE
COMBUSTIBLE
CEILING
LISTED
CHIMNEY
COMBUSTIBLE
OUTSIDE WALL
TO
STOVE
2” (50.8mm)
CLEARANCE
INSULATED
“T”
WALL
SUPPORT
WALL SPACER
FOR OUTSIDE
WALL
SECTION
LISTED
CHIMNEY PIPE
THIMBLE
CHIMNEY
CONNECTOR

W415-2796 / B / 12.19.19
EN
18
installation
3.1.5 typical existing masonry
You can also install your appliance using your
existing masonry chimney. To do so, use the
following guidelines. Use a factory-built thimble, or
construct your own brick thimble. If you are using a
masonry chimney, it is important that it be built in
compliance with the specifications of the Building
Code in your region. It must normally be lined with
fire clay bricks, metal or clay tiles sealed together
with fire cement. (Round flues are the most
efficient). The maximum flue size is 8” (203.2mm) x
8” (203.2mm) square or 6” (152.4mm) round. For
greater diameters it is necessary to install a 6”
(152.4mm) stainless steel liner.
FLOOR
PROTECTOR
CHIMNEY
CONNECTOR
COMBUSTIBLE
WALL
CLEARANCE
EAVE
RAFTER
CLEARANCE WITH FIRESTOP
CEILING JOIST
THIMBLE

EN
W415-2796 / B / 12.19.19
19
4.0 fi nishing
4.1 door removal
!
WARNING
• Burning your appliance in with the doors open or ajar creates a fi re hazard that may result in a house and/or
chimney fi re.
• Do not strike or slam door.
• Never remove the door when the appliance is hot.
Fig. 4-1
Fig. 4-2
A
B
1. With one hand on the door to prevent it from falling, open the door and remove the 6 large screws located
on the hinges (Fig. 4-1).
2. Remove the door, placing it face down on a soft, non-abrasive surface (Fig. 4-2). Be careful not to
scratch the paint.
3. Reverse these steps to install the door.
We strongly recommend using two people to remove and/or install the appliance door as it is very heavy.
note:
Hinge MUST stay secured to
appliance during door removal
/ installation.
note:

W415-2796 / B / 12.19.19
EN
20
fi nishing
4.2 door adjustment
!
WARNING
• Burning your appliance in with the doors open or ajar creates a fi re hazard that may result in a house and/or
chimney fi re.
• Do not strike or slam door.
• Never remove the door when the appliance is hot.
4.3 door handle installation
Front View Back View
Door Knob
Door Handle
Spring
Washer
Spacer
Door Latch
Spring
Washer
Lock Nut
Door
1. After removing and reinstalling the door (see
“door removal” section), the door may not be
level. In this case, door adjustment may be
necessary.
2. To align the door, loosen the set screws. Rotate
the hinge pins clockwise or counter-clockwise
to raise or lower the opposite end of the door.
Tighten the set screw.
3. Ensure the door latch closes and engages
properly.
Door adjustment is strictly trial and error; you
may need to perform this adjustment a few
times until the desired door angle is attained.
note:
This hinge pin is an offset cam, which means it can move the door away from or closer to the fi rebox face,
either creating a gap between it and the door gasket or making the door fi t too tight. Adjust accordingly.
note:
Some parts
hidden for clarity.
Allen Key Size:
1/8”
Set Screw
Hinge
Pin