National Instruments NI PXIe-7976R User manual

PXIe-7976

GETTING STARTED GUIDE
NI PXIe-7976R
NI FlexRIO™FPGA Module for PXI Express
This document explains how to install your NI FlexRIO system, comprised of the
NI PXIe-7976R (NI 7976R) FlexRIO FPGA module and an NI FlexRIO adapter module.
For information about the device specifications, refer to the NI PXIe-7976R Specifications,
available at Start»All Programs»National Instruments»NI FlexRIO, and at ni.com/
manuals.
For detailed information about the features and configuration options specific to the
NI FlexRIO FPGA module, refer to the NI FlexRIO Help, available at Start»All Programs»
National Instruments»NI FlexRIO, and at ni.com/manuals.
Contents
How to Use Your NI FlexRIO Documentation Set...................................................................2
Required Components...............................................................................................................3
Installing the Application Software and Driver........................................................................ 5
Installing the NI FlexRIO Devices............................................................................................6
Unpacking......................................................................................................................... 6
Preparing the Environment............................................................................................... 6
Installing the NI FlexRIO FPGA Module.........................................................................7
Confirming that Measurement & Automation Explorer (MAX) Recognizes the
Device......................................................................................................................... 8
Installing the NI FlexRIO Adapter Module...................................................................... 9
Installing PXI EMC Filler Panels........................................................................................... 10
NI FlexRIO FPGA Module Signals........................................................................................ 10
Compliance and Certifications................................................................................................12
Safety.............................................................................................................................. 12
Electromagnetic Compatibility....................................................................................... 12
CE Compliance .............................................................................................................. 12
Online Product Certification........................................................................................... 13
Environmental Management........................................................................................... 13
Electromagnetic Compatibility Guidelines.............................................................................13
Worldwide Support and Services............................................................................................ 14

How to Use Your NI FlexRIO Documentation Set
Figure 1. How to Use Your NI FlexRIO Documentation Set
LabVIEW FPGA
Module Help
NI FlexRIO
Help
LabVIEW
Examples
INSTALL Hardware
and Software
CONNECT Signals
and LearnAbout
Your AdapterModule
LEARN About
LabVIEW FPGA
Module
PROGRAM Your
NI FlexRIO System
in LabVIEW FPGA
Module
Specifications document
for your FPGA module
Specifications document
for your adapter module
Are
You New to
LabVIEW FPGA
Module?
Yes No
No
Getting Started Guide
for your adapter module
Getting Started Guide
for your FPGA module
Table 1. NI FlexRIO Documentation Locations and Descriptions
Document Location Description
Getting started guide for
your FPGA module
Available from the Start menu
and at ni.com/manuals.
Contains installation instructions
for your NI FlexRIO system.
Specifications document
for your FPGA module
Available from the Start menu
and at ni.com/manuals.
Contains specifications for your
NI 7976R module.
Getting started guide for
your adapter module
Available from the Start menu
and at ni.com/manuals.
Contains signal information,
examples, and CLIP details for
your adapter module.
Specifications document
for your adapter module
Available from the Start menu
and at ni.com/manuals.
Contains specifications for your
adapter module.
LabVIEW FPGA Module
Help
Embedded in LabVIEW Help
and at ni.com/manuals.
Contains information about the
basic functionality of the
LabVIEW FPGA Module.
2| ni.com | NI PXIe-7976R FPGA Module Getting Started Guide

Table 1. NI FlexRIO Documentation Locations and Descriptions (Continued)
Document Location Description
NI FlexRIO Help Available from the Start menu
and at ni.com/manuals.
Contains information about the
FPGA module, adapter module,
and CLIP configuration
information.
LabVIEW Examples Available in NI Example
Finder. In LabVIEW, click
Help»Find Examples»
Hardware Input and
Output»FlexRIO.
Contains examples of how to run
FPGA VIs and Host VIs on your
device.
IPNet ni.com/ipnet Contains LabVIEW FPGA
functions and intellectual property
to share.
NI FlexRIO product
page
ni.com/flexrio Contains product information and
data sheets for NI FlexRIO
devices.
Required Components
The following items are necessary to set up and use your NI FlexRIO system:
• The NI FlexRIO hardware device, comprised of the following items:
– NI 7976R
– NI FlexRIO adapter module
Note You can use the NI FlexRIO FPGA module without an adapter module for
coprocessing or peer-to-peer streaming. The adapter module installation instructions
in this document do not apply to these circumstances.
The following figure shows the combined module.
NI PXIe-7976R FPGA Module Getting Started Guide | © National Instruments | 3

Figure 2. Combining Your Adapter Module and FPGA Module
NI FlexRIO
Adapter Module + = NI FlexRIO Device
NI FlexRIO
FPGA Module
• The following software packages:
– LabVIEW
– LabVIEW FPGA Module
– NI FlexRIO Support
Note The most recent version of NI FlexRIO Support is available at
ni.com/downloads. Search for flexrio to download the latest version of
NI FlexRIO Support.
– NI FlexRIO Adapter Module Support1
Note The most recent version of NI FlexRIO Adapter Module Support is
available at ni.com/downloads. Search for flexrio adapter module
support to download the latest version of NI FlexRIO Adapter Module
Support. You do not need this software if you are not using an adapter
module.
– (Optional) LabVIEW Real-Time Module.
• A PXI Express/CompactPCI Express chassis
• One of the following controllers:
– PXI Express/CompactPCI Express embedded controller
– MXI kit and a PC
• One of the following operating systems:
– Windows 8
– Windows 7
1The NI 1483 adapter module requires the NI-IMAQ instrument driver instead of NI FlexRIO
Adapter Module Support.
4| ni.com | NI PXIe-7976R FPGA Module Getting Started Guide

– Windows Vista
– Windows XP Pro x32 Service Pack 2 or Service Pack 3
• At least one cable for connecting signals to the NI FlexRIO device. Refer to your adapter
module documentation for a list of applicable cables and accessories for your NI FlexRIO
system.
Related Information
Installing the Application Software and Driver on page 5
Installing the Application Software and Driver
Before installing your hardware, you must install the application software and instrument
driver. Visit ni.com/info and enter rdsoftwareversion as the Info Code to determine
which minimum software versions you need for your device. Install the software in the
following order:
1. Install LabVIEW.
Refer to the LabVIEW Installation Guide for installation instructions for LabVIEW and
system requirements for the LabVIEW software. Refer to the LabVIEW Upgrade Notes
for additional information about upgrading to the most recent version of LabVIEW for
Windows. Documentation for LabVIEW is available at ni.com/manuals and by selecting
Start»All Programs»National Instruments»LabVIEW»LabVIEW Manuals.
2. Install the LabVIEW FPGA Module.
Refer to the LabVIEW FPGA Module Release and Upgrade Notes for installation
instructions and information about getting started with the LabVIEW FPGA Module.
Documentation for the LabVIEW FPGA Module is available at ni.com/manuals and by
selecting Start»All Programs»National Instruments»LabVIEW»LabVIEW
Manuals.
3. (Optional) Install the LabVIEW Real-Time Module.
Refer to the LabVIEW Real-Time Module Release and Upgrade Notes for system
requirements, installation instructions, and additional information about using the
LabVIEW Real-Time Module.
4. Install NI FlexRIO.
Refer to the NI FlexRIO Readme on the NI FlexRIO installation media for system
requirements and installation instructions for NI FlexRIO Support. Documentation for
NI FlexRIO Support is available at ni.com/manuals and by selecting Start»All
Programs»National Instruments»NI FlexRIO.
Note If you are not using an adapter module, skip step 5.
5. Install NI FlexRIO Adapter Module Support.
Refer to the NI FlexRIO Adapter Module Support Readme on the NI FlexRIO Adapter
Module Support installation media for system requirements and installation instructions.
Documentation for NI FlexRIO Adapter Module Support is available at ni.com/manuals
NI PXIe-7976R FPGA Module Getting Started Guide | © National Instruments | 5

and by selecting Start»All Programs»National Instruments»NI FlexRIO»NI FlexRIO
Adapter Module Documentation.
Related Information
Required Components on page 3
NI FlexRIO FPGA Module Signals on page 10
Installing the NI FlexRIO FPGA Module on page 7
Installing the NI FlexRIO Devices
Note You must install the software before installing the hardware.
Unpacking
The NI 7976R modules ship in antistatic packages to prevent electrostatic discharge from
damaging module components. To prevent such damage when handling the modules, ground
yourself using a grounding strap or by holding a grounded object, such as your computer
chassis, and complete the following steps:
1. Touch the antistatic package to a metal part of the computer chassis before removing the
module from the package.
Caution Never touch the exposed pins of connectors.
2. Remove each module from the package and inspect it for loose components or any other
sign of damage.
Notify NI if the modules appear damaged in any way. Do not install a damaged module into
the chassis.
Preparing the Environment
Ensure that the environment you are using the NI 7976R in meets the following specifications.
............................................................................
Operating temperature (IEC
60068-2-1, IEC60068-2-2)
0 °C to 55 °C
............................................................................Operating humidity
(IEC 60068-2-56)
10% to 90% RH, noncondensing
............................................................................Pollution Degree 2
............................................................................Maximum altitude 2,000 m at 25 °C ambient temperature
Indoor use only.
Note Refer to the NI PXIe-7976R Specifications at ni.com/manuals for complete
specifications.
6| ni.com | NI PXIe-7976R FPGA Module Getting Started Guide

Installing the NI FlexRIO FPGA Module
Note You must install the software before you install the hardware.
1. Power off and unplug the PXI Express chassis. Refer to your chassis manual to install or
configure the chassis.
2. Identify a supported PXI Express slot in the chassis. The figure below shows the symbols
that indicate the slot types in a PXI Express chassis.
Figure 3. Symbols for PXI Express/PXI Express HybridSlots
NI PXIe-1062Q
12 3 4 5
1. PXI Express System Controller Slot
2. PXI Peripheral Slot
3. PXI Express Hybrid Peripheral Slot
4. PXI Express System Timing Slot
5. PXI Express Peripheral Slot
Refer to the chassis documentation for specifications.
3. Remove the filler panel of an unused PXI Express slot.
4. Touch any metal part of the chassis to discharge any static electricity. Place the PXI
Express module edges into the module guides at the top and bottom of the chassis, and
slide the module into the chassis until the module is fully inserted, as shown in the figure
below.
NI PXIe-7976R FPGA Module Getting Started Guide | © National Instruments | 7

Figure 4. Installing an NI FlexRIO FPGA Module in the PXI Express Chassis
PXI-1000B
1
3
6
2
5
4
1. PXI Express Chassis
2. PXI Express System Controller
3. NI FlexRIO FPGA Module
4. Front-Panel Mounting Screws
5. Module Guides
6. Power Switch
5. Secure the device front panel to the chassis front panel mounting rail using the front panel
mounting screws.
6. Plug in and power on the PXI Express chassis.
Related Information
Installing the Application Software and Driver on page 5
Confirming that Measurement & Automation Explorer
(MAX) Recognizes the Device
Use Measurement & Automation Explorer (MAX) to configure your National Instruments
hardware. MAX informs other programs about which devices reside in the system and how
they are configured. MAX is automatically installed with NI FlexRIO Support.
1. Launch MAX by navigating to Start»All Programs»National Instruments»NI MAX or
by clicking the NI MAX desktop icon.
2. In the Configuration pane, double-click Devices and Interfaces to see the list of installed
devices. Installed devices appear under the name of their associated chassis.
8| ni.com | NI PXIe-7976R FPGA Module Getting Started Guide

3. Expand your Chassis tree item. MAX lists all devices installed in the chassis. Your
default device names may vary.
Note If you do not see your hardware listed, press <F5> to refresh the list of
installed devices. If the device is still not listed, power off the system, ensure
the device is correctly installed, and restart.
Installing the NI FlexRIO Adapter Module
Note Skip this step if you are not using an adapter module.
1. Gently insert the guide pins and the high-density card edge of the NI FlexRIO adapter
module into the corresponding connectors of the NI FlexRIO FPGA module, as shown in
the figure below.
Figure 5. Installing the NI FlexRIO Adapter Module
PXI-1000B
1
4
3
2
5
1. NI FlexRIO Adapter Module
2. Captive Screw
3. Guide Pin
4. PXI/PXI Express Chassis
5. NI FlexRIO FPGA Module
The connection may be tight, but do not force the adapter module into place.
2. Tighten the captive screws on the NI FlexRIO adapter module to secure it to the
NI FlexRIO FPGA module. NI recommends using the laser-tipped screwdriver (part
number 748677-01) included in the NI PXIe-7976R packaging.
3. Launch LabVIEW to begin configuring your NI FlexRIO system.
Note MAX only recognizes FPGA modules that are in the chassis. Your
adapter module will not appear in MAX.
NI PXIe-7976R FPGA Module Getting Started Guide | © National Instruments | 9

Installing PXI EMC Filler Panels
To ensure specified EMC performance, PXI EMC filler panels must be properly installed in
your NI FlexRIO system. The PXI EMC filler panels (National Instruments part number
778700-01) must be purchased separately.
1. Remove the captive screw covers.
2. Install the PXI EMC filler panels by securing the captive mounting screws to the chassis,
as shown in the figure below. Make sure that the EMC gasket is on the right side of the
PXI EMC filler panel.
Figure 6. PXI EMC Filler Panels and Chassis
1
1
3
2
1. Captive Screw Covers
2. Captive Mounting Screws
3. EMC Gasket
Note You must populate all slots with a module or a PXI EMC filler panel to
ensure proper module cooling. Do not over tighten screws (2.5 lb · in.
maximum). For additional information about the use of PXI EMC filler panels
in your PXI system, visit ni.com/info and enter emcpanels.
NI FlexRIO FPGA Module Signals
The following figure shows the available signals on the NI FlexRIO FPGA module. Refer to
your adapter module specifications for your adapter module pinout.
10 | ni.com | NI PXIe-7976R FPGA Module Getting Started Guide

Figure 7. NI FlexRIO FPGA Module Front Connector Pin Assignments and Locations
Bank 0
PCB
Primary Side
+3.3V
SCL
TB_Present
+12V
Vcco
RSVD
GND
IOModSyncClk_n
IOModSyncClk
GND
GPIO_0_n
GPIO_0
GND
GPIO_1_n
GPIO_1
GND
GPIO_CC_2_n
GPIO_CC_2
GND
GPIO_3_n
GPIO_3
GND
GPIO_4_n
GPIO_4
GND
GPIO_5_n
GPIO_5
GND
GPIO_6_n
GPIO_6
GND
GPIO_7_n
GPIO_7
GND
GPIO_8_n
GPIO_8
GND
GPIO_9_n
GPIO_9
GND
GPIO_10_n
GPIO_10
GND
GPIO_11_n
GPIO_11
GND
GPIO_12_n
GPIO_12
GND
GND
GPIO_13_n
GPIO_13
P2
P1
S148
S147
S146
S145
S144
S143
G36
S142
S141
G35
S140
S139
G34
S138
S137
G33
S136
S135
G32
S134
S133
G31
S132
S131
G30
S130
S129
G29
S128
S127
G28
S126
S125
G27
S124
S123
G26
S122
S121
G25
S120
S119
G24
S118
S117
G23
S116
S115
G22
G37
P2
P1
S74
S73
S72
S71
S70
S69
G36
S68
S67
G35
S66
S65
G34
S64
S63
G33
S62
S61
G32
S60
S59
G31
S58
S57
G30
S56
S55
G29
S54
S53
G28
S52
S51
G27
S50
S49
G26
S48
S47
G25
S46
S45
G24
S44
S43
G23
S42
S41
G22
G37
+12V
+3.3V
SDA
TB_Power_Good
Vcco
Veeprom
TDC_Assert_CLK_n
TDC_Assert_CLK
GND
GPIO_24_n
GPIO_24
GND
GPIO_25_n
GPIO_25
GND
GPIO_CC_26_n
GPIO_CC_26
GND
GPIO_27_n
GPIO_27
GND
GPIO_28_n
GPIO_28
GND
GPIO_29_n
GPIO_29
GND
GPIO_30_n
GPIO_30
GND
GPIO_31_n
GPIO_31
GND
GPIO_32_n
GPIO_32
GND
GPIO_33_n
GPIO_33
GND
GPIO_34_n
GPIO_34
GND
GPIO_35_n
GPIO_35
GND
GPIO_36_n
GPIO_36
GND
GPIO_37_n
GPIO_37
GND
GND
PCB
Secondary Side
Bank 1
PCB
Primary Side
GND
GPIO_CC_14_n
GPIO_CC_14
GND
GPIO_15_n
GPIO_15
GND
GPIO_16_n
GPIO_16
GND
GPIO_17_n
GPIO_17
GND
GPIO_18_n
GPIO_18
GND
GPIO_19_n
GPIO_19
GND
GPIO_20_n
GPIO_20
GND
GPIO_21_n
GPIO_21
GND
GPIO_22_n
GPIO_22
GND
GPIO_23_n
GPIO_23
GND
GPIO_58_n
GPIO_58
GND
GPIO_59_n
GPIO_59
GND
GPIO_CC_60_n
GPIO_CC_60
GND
GPIO_61_n
GPIO_61
GND
GPIO_62_n
GPIO_62
GND
GPIO_63_n
GPIO_63
GND
GND
GPIO_64_n
GPIO_64
GPIO_65_n
GPIO_65
GND
GPIO_66_n
GPIO_67_n
GPIO_66
GND
GND
GPIO_67
G20
G21
S114
S113
S112
S111
S110
S109
G18
S108
S107
G17
S106
S105
G16
S104
S103
G15
S102
S101
G14
S100
S99
G13
S98
S97
G12
S96
S95
G11
S94
S93
G10
S92
S91
G9
S90
S89
G8
S88
S87
G7
S86
S85
G6
S84
S83
G5
S82
S81
G4
G19
S80
S79
G3
S78
S77
G2
S76
S75
G1
G20
G21
S40
S39
S38
S37
S36
S35
G18
S34
S33
G17
S32
S31
G16
S30
S29
G15
S28
S27
G14
S26
S25
G13
S24
S23
G12
S22
S21
G11
S20
S19
G10
S18
S17
G9
S16
S15
G8
S14
S13
G7
S12
S11
G6
S10
S9
G5
S8
S7
G4
G19
S6
S5
G3
S4
S3
G2
S2
S1
G1
GND
GND
GPIO_CC_38_n
GPIO_CC_38
GPIO_39_n
GPIO_39
GPIO_40_n
GPIO_40
GND
GPIO_41_n
GPIO_41
GND
GPIO_42_n
GPIO_42
GND
GPIO_43_n
GPIO_43
GND
GPIO_44_n
GPIO_44
GND
GPIO_45_n
GPIO_45
GND
GPIO_46_n
GPIO_46
GND
GPIO_47_n
GPIO_47
GND
GPIO_48_n
GPIO_48
GND
GPIO_49_n
GPIO_49
GND
GPIO_CC_50_n
GPIO_CC_50
GND
GPIO_51_n
GPIO_51
GND
GPIO_52_n
GPIO_52
GND
GPIO_53_n
GPIO_53
GND
GPIO_54_n
GPIO_54
GND
GPIO_55_n
GPIO_55
GND
GPIO_56_n
GPIO_56
GND
GPIO_57_n
GPIO_57
GND
GND
PCB
Secondary Side
Bank 2
Bank 0
Bank 2 Bank 1
NI PXIe-7976R
NI FlexRIO
Kintex-7
410T
FPGA
Note Pins S72 and S146 are shorted together on the NI 7976R.
Related Information
Installing the Application Software and Driver on page 5
NI PXIe-7976R FPGA Module Getting Started Guide | © National Instruments | 11

Compliance and Certifications
Safety
This product is designed to meet the requirements of the following electrical equipment safety
standards for measurement, control, and laboratory use:
• IEC 61010-1, EN 61010-1
• UL 61010-1, CSA 61010-1
Note For UL and other safety certifications, refer to the product label or the Online
Product Certification section.
Electromagnetic Compatibility
This product meets the requirements of the following EMC standards for electrical equipment
for measurement, control, and laboratory use:
• EN 61326-1 (IEC 61326-1): Class A emissions; Basic immunity
• EN 55011 (CISPR 11): Group 1, Class A emissions
• EN 55022 (CISPR 22): Class A emissions
• EN 55024 (CISPR 24): Immunity
• AS/NZS CISPR 11: Group 1, Class A emissions
• AS/NZS CISPR 22: Class A emissions
• FCC 47 CFR Part 15B: Class A emissions
• ICES-001: Class A emissions
Note In the United States (per FCC 47 CFR), Class A equipment is intended for
use in commercial, light-industrial, and heavy-industrial locations. In Europe,
Canada, Australia, and New Zealand (per CISPR 11), Class A equipment is intended
for use only in heavy-industrial locations.
Note Group 1 equipment (per CISPR 11) is any industrial, scientific, or medical
equipment that does not intentionally generate radio frequency energy for the
treatment of material or inspection/analysis purposes.
Note For EMC declarations, certifications, and additional information, refer to the
Online Product Certification section.
CE Compliance
This product meets the essential requirements of applicable European Directives, as follows:
• 2006/95/EC; Low-Voltage Directive (safety)
• 2004/108/EC; Electromagnetic Compatibility Directive (EMC)
12 | ni.com | NI PXIe-7976R FPGA Module Getting Started Guide

Online Product Certification
To obtain product certifications and the DoC for this product, visit ni.com/certification, search
by model number or product line, and click the appropriate link in the Certification column.
Environmental Management
NI is committed to designing and manufacturing products in an environmentally responsible
manner. NI recognizes that eliminating certain hazardous substances from our products is
beneficial to the environment and to NI customers.
For additional environmental information, refer to the Minimize Our Environmental Impact
web page at ni.com/environment. This page contains the environmental regulations and
directives with which NI complies, as well as other environmental information not included in
this document.
Waste Electrical and Electronic Equipment (WEEE)
EU Customers At the end of the product life cycle, all products must be sent to a
WEEE recycling center. For more information about WEEE recycling centers,
National Instruments WEEE initiatives, and compliance with
WEEE Directive 2002/96/EC on Waste Electrical and Electronic Equipment, visit
ni.com/environment/weee.
电子信息产品污染控制管理办法（中国 RoHS）
中国客户 National Instruments 符合中国电子信息产品中限制使用某些有害物
质指令(RoHS)。关于 National Instruments 中国 RoHS 合规性信息，请登录
ni.com/environment/rohs_china。(For information about China RoHS
compliance, go to ni.com/environment/rohs_china.)
Electromagnetic Compatibility Guidelines
This product was tested and complies with the regulatory requirements and limits for
electromagnetic compatibility (EMC) stated in the product specifications. These requirements
and limits provide reasonable protection against harmful interference when the product is
operated in the intended operational electromagnetic environment.
This product is intended for use in industrial locations. However, harmful interference may
occur in some installations, when the product is connected to a peripheral device or test object,
or if the product is used in residential or commercial areas. To minimize interference with
radio and television reception and prevent unacceptable performance degradation, install and
use this product in strict accordance with the instructions in the product documentation.
Furthermore, any changes or modifications to the product not expressly approved by National
Instruments could void your authority to operate it under your local regulatory rules.
NI PXIe-7976R FPGA Module Getting Started Guide | © National Instruments | 13

Caution To ensure the specified EMC performance, operate this product only with
shielded cables and accessories.
Caution Refer to the Read Me First: Safety and Electromagnetic Compatibility
document for important safety and electromagnetic compatibility information. To
obtain a copy of this document online, visit ni.com/manuals, and search for the
document title.
Caution When exposed to transient electromagnetic phenomena such as
electrostatic discharge (ESD) or power surges, this product may experience a
temporary upset or other performance degradation that requires more than 10
seconds for self-recovery.
Caution The NI FlexRIO FPGA module front panel interface is sensitive to
electrostatic discharge. Use caution when handling the NI FlexRIO FPGA module to
prevent damage to the internal components exposed by this interface.
Caution Using the NI 7976R in a manner not described in this document may
impair the protection the NI 7976R provides.
Worldwide Support and Services
The National Instruments website is your complete resource for technical support. At ni.com/
support, you have access to everything from troubleshooting and application development
self-help resources to email and phone assistance from NI Application Engineers.
Visit ni.com/services for NI Factory Installation Services, repairs, extended warranty, and
other services.
Visit ni.com/register to register your National Instruments product. Product registration
facilitates technical support and ensures that you receive important information updates from
NI.
A Declaration of Conformity (DoC) is our claim of compliance with the Council of the
European Communities using the manufacturer’s declaration of conformity. This system
affords the user protection for electromagnetic compatibility (EMC) and product safety. You
can obtain the DoC for your product by visiting ni.com/certification. If your product supports
calibration, you can obtain the calibration certificate for your product at ni.com/calibration.
National Instruments corporate headquarters is located at 11500 North Mopac Expressway,
Austin, Texas, 78759-3504. National Instruments also has offices located around the world.
For telephone support in the United States, create your service request at ni.com/support or
dial 1 866 ASK MYNI (275 6964). For telephone support outside the United States, visit the
Worldwide Offices section of ni.com/niglobal to access the branch office websites, which
provide up-to-date contact information, support phone numbers, email addresses, and current
events.
14 | ni.com | NI PXIe-7976R FPGA Module Getting Started Guide

Refer to the NI Trademarks and Logo Guidelines at ni.com/trademarks for information on National Instruments trademarks.
Other product and company names mentioned herein are trademarks or trade names of their respective companies. For patents
covering National Instruments products/technology, refer to the appropriate location: Help»Patents in your software, the
patents.txt file on your media, or the National Instruments Patent Notice at ni.com/patents. You can find information about
end-user license agreements (EULAs) and third-party legal notices in the readme file for your NI product. Refer to the Export
Compliance Information at ni.com/legal/export-compliance for the National Instruments global trade compliance policy and
how to obtain relevant HTS codes, ECCNs, and other import/export data. NI MAKES NO EXPRESS OR IMPLIED WARRANTIES
AS TO THE ACCURACY OF THE INFORMATION CONTAINED HEREIN AND SHALL NOT BE LIABLE FOR ANY ERRORS.
U.S. Government Customers: The data contained in this manual was developed at private expense and is subject to the
applicable limited rights and restricted data rights as set forth in FAR 52.227-14, DFAR 252.227-7014, and DFAR 252.227-7015.
© 2014 National Instruments. All rights reserved.
376248A-01 Jul14