National Instruments NI-5783 User manual

NI-5783

GETTING STARTED GUIDE
NI 5783
Four Channel Transceiver Adapter Module
Note Before you begin, complete the software and hardware installation
instructions in the getting started guide for your FlexRIO FPGA module or
Controller for FlexRIO.
The NI 5783 is a FlexRIO adapter module designed to work in conjunction with FlexRIO
FPGA modules and Controllers for FlexRIO.
The NI 5783 is available in two variants. The NI 5783-01 variant is a 40 MHz Elliptic Filter
(Frequency Domain). The NI 5783-02 variant is a 40 MHz Butterworth Filter (Time Domain).
Unless otherwise specified, all descriptions in this document refer to both variants.
The NI 5783 features 4 analog input channels with 16-bit resolution and sample rates up to
100 MS/s, and 4 analog output channels with 16-bit resolution and sample rates up to
100 MS/s or 200 MS/s.
Note The NI 5783 is compatible only with NI PXIe-797xR and NI-793xR devices.
This document explains how to install and configure the NI 5783.
Contents
Electromagnetic Compatibility Guidelines...............................................................................2
FlexRIO Documentation........................................................................................................... 2
Verifying the System Requirements..........................................................................................4
Unpacking................................................................................................................................. 4
Preparing the Environment....................................................................................................... 4
Installing the NI 5783............................................................................................................... 5
Confirming that Measurement & Automation Explorer (MAX) Recognizes the Device........ 5
Recommended Cables...............................................................................................................6
Accessories................................................................................................................................6
Front Panel and Connector Pinouts...........................................................................................6
AUX I/O Connector.......................................................................................................... 8
Block Diagram.......................................................................................................................... 9
Logic Diagram.......................................................................................................................... 9
Component-Level Intellectual Property (CLIP)..................................................................... 10
NI 5783 CLIP..................................................................................................................10
NI 5783 400 MSPS AO CLIP.........................................................................................11
Clocking.................................................................................................................................. 11

Worldwide Support and Services............................................................................................ 12
Where to Go Next................................................................................................................... 12
Electromagnetic Compatibility Guidelines
This product was tested and complies with the regulatory requirements and limits for
electromagnetic compatibility (EMC) stated in the product specifications. These requirements
and limits are designed to provide reasonable protection against harmful interference when the
product is operated in the intended operational electromagnetic environment.
This product is intended for use in industrial locations. However, harmful interference may
occur in some installations, when the product is connected to a peripheral device or test object,
or if the product is used in residential or commercial areas. To minimize interference with
radio and television reception and prevent unacceptable performance degradation, install and
use this product in strict accordance with the instructions in the product documentation.
Furthermore, any modifications to the product not expressly approved by National Instruments
could void your authority to operate it under your local regulatory rules.
Caution To ensure the specified EMC performance, operate this product only with
shielded cables and accessories.
Caution To ensure the specified EMC performance, the length of all I/O cables
must be no longer than 3 m (10 ft).
FlexRIO Documentation
Table 1. FlexRIO Documentation Locations and Descriptions
Document Location Description
Getting started guide
for your FlexRIO
FPGA module or
Controller for
FlexRIO
Available from the Start menu
and at ni.com/manuals.
Contains installation instructions
for your FlexRIO system.
Specifications
document for your
FlexRIO FPGA
module or Controller
for FlexRIO
Available from the Start menu
and at ni.com/manuals.
Contains specifications for your
FlexRIO FPGA module or
Controller for FlexRIO.
Getting started guide
for your adapter
module
Available from the Start menu
and at ni.com/manuals.
Contains signal information,
examples, and CLIP details for
your adapter module.
2| ni.com | NI 5783 Getting Started Guide

Table 1. FlexRIO Documentation Locations and Descriptions (Continued)
Document Location Description
Specifications
document for your
adapter module
Available from the Start menu
and at ni.com/manuals.
Contains specifications for your
adapter module.
LabVIEW FPGA
Module Help
Embedded in LabVIEW Help
and at ni.com/manuals.
Contains information about the
basic functionality of the
LabVIEW FPGA Module.
Real-Time Module
Help
Embedded in LabVIEW Help
and at ni.com/manuals.
Contains information about real-
time programming concepts, step-
by-step instructions for using
LabVIEW with the Real-Time
Module, reference information
about Real-Time Module VIs and
functions, and information about
LabVIEW features on real-time
operating systems.
FlexRIO Help Available from the Start menu
and at ni.com/manuals.
Contains information about the
FPGA module front panel
connectors and I/O, controller for
FlexRIO front panel connectors
and I/O, programming
instructions, and adapter module
component-level IP (CLIP).
FlexRIO Adapter
Module Development
Kit User Manual
Available from the Start menu
at Start»All Programs»
National Instruments»NI
FlexRIO»NI FlexRIO
Adapter Module Development
Kit»Documentation.
Contains information about how
to create custom adapter modules
for use with FlexRIO FPGA
modules.
LabVIEW Examples Available in NI Example
Finder. In LabVIEW, click
Help»Find Examples»
Hardware Input and Output»
FlexRIO.
Contains examples of how to run
FPGA VIs and Host VIs on your
device.
NI 5783 Getting Started Guide | © National Instruments | 3

Table 1. FlexRIO Documentation Locations and Descriptions (Continued)
Document Location Description
IPNet Located at ni.com/ipnet. Contains LabVIEW FPGA
functions and intellectual property
to share.
FlexRIO product page Located at ni.com/flexrio. Contains product information and
data sheets for FlexRIO devices.
Verifying the System Requirements
To use the NI 5783, your system must meet certain requirements. For more information about
minimum system requirements, recommended system, and supported application development
environments (ADEs), refer to the readme, which is available on the software media or online
at ni.com/updates.
Unpacking
Caution To prevent ESD from damaging the devices, ground yourself using a
grounding strap or by holding a grounded object, such as your computer chassis.
1. Touch the antistatic package to a metal part of the computer chassis.
2. Remove each module from the package and inspect it for loose components or any other
sign of damage.
Caution Never touch the exposed pins of connectors.
Note Do not install a device if it appears damaged in any way.
3. Unpack any other items and documentation from the kit.
Store the devices in the antistatic package when they are not in use.
Preparing the Environment
Ensure that the environment you are using the NI 5783 in meets the following specifications.
Operating temperature (IEC 60068-2-1,
IEC 60068-2-2)
0 °C to 55 °C
Operating humidity (IEC 60068-2-56) 10% to 90% RH, noncondensing
4| ni.com | NI 5783 Getting Started Guide

Pollution Degree 2
Maximum altitude 2,000 m at 25 °C ambient temperature
Indoor use only.
Note Refer to the NI 5783 Specifications at ni.com/manuals for complete
specifications.
Caution Clean the hardware with a soft, nonmetallic brush. Make sure that the
hardware is completely dry and free from contaminants before returning it to
service.
Installing the NI 5783
Refer to the getting started guide for your FlexRIO FPGA module or Controller for FlexRIO
for instructions about how to install your FlexRIO system, including the NI 5783.
Confirming that Measurement & Automation
Explorer (MAX) Recognizes the Device
Use Measurement & Automation Explorer (MAX) to configure your NI hardware. MAX
informs other programs about which devices reside in the system and how they are configured.
MAX is automatically installed with FlexRIO Support.
1. Launch MAX by navigating to Start»All Programs»National Instruments»NI MAX or
by clicking the NI MAX desktop icon.
2. In the Configuration pane, double-click Devices and Interfaces to see the list of installed
devices. Installed devices appear under the name of their associated chassis.
3. (PXI and PXI Express devices only) Expand your Chassis tree item. MAX lists all
devices installed in the chassis. Your default device names may vary.
Note If you do not see your hardware listed, press <F5> to refresh the list of
installed devices. If the device is still not listed, power off the system, ensure
the device is correctly installed, and restart.
4. (Controllers for FlexRIO only) Your device appears under the Remote Devices section.
NI 5783 Getting Started Guide | © National Instruments | 5

Recommended Cables
NI recommends using the following cables to connect signals to the NI 5783.
Cable NI Part Number
HDBNC to SMA 769177-01
HDBNC to BNC 769028-01
Accessories
The NI 5783 can be used with the SCB-19 shielded desktop connector block.
Refer to the SCB-19 User Guide for information about how to connect and use the SCB-19
with the AUX I/O front panel connector on your NI 5783.
Related Information
AUX I/O Connector on page 8
Front Panel and Connector Pinouts
The following figure shows the front panel connectors for the NI 5783.
6| ni.com | NI 5783 Getting Started Guide

Device Front Panel Connector Signal Description
200 MS/s AO
100 MS/s AI
16-Bit AO-AI
NI 5783
INSTRUMENTS
NATIONAL
AUX
I/O
TRIG
CLK/
REF
IN
AI 3
AI 2
AI 1
AI 0
AO 3
AO 2
AO 1
AO 0
AO 0 Analog input channel, 50 Ω, single-ended, DC-coupled
AO 1
AO 2
AO 3
AI 0 Analog output channel, 50 Ω, single-ended, DC-
coupled
AI 1
AI 2
AI 3
CLK/REF IN External Reference Clock or Sample Clock input
TRIG Trigger input and output channel
AUX I/O Digital I/O and PFI connector
Caution To avoid permanent damage to the NI 5783, disconnect all signals
connected to the NI 5783 before powering down the module, and connect signals
only after the adapter module has been powered on by the FlexRIO FPGA module or
Controller for FlexRIO.
Caution Connections that exceed any of the maximum ratings of any connector on
the NI 5783 can damage the device and the chassis. NI is not liable for any damage
resulting from such connections.
NI 5783 Getting Started Guide | © National Instruments | 7

AUX I/O Connector
Table 2. NI 5783 AUX I/O Connector Pin Assignments
AUX I/O Connector Pin Signal Signal Description
18
16
14
12
10
8
6
4
2
19
17
1
3
5
7
9
11
13
15
1 DIO Port 0 (0) Bidirectional single-ended (SE) digital I/O (DIO)
data channel.
2 GND Ground reference for signals.
3 DIO Port 0 (1) Bidirectional SE DIO data channel.
4 DIO Port 0 (2) Bidirectional SE DIO data channel.
5 GND Ground reference for signals.
6 DIO Port 0 (3) Bidirectional SE DIO data channel.
7 DIO Port 1 (0) Bidirectional SE DIO data channel.
8 GND Ground reference for signals.
9 DIO Port 1 (1) Bidirectional SE DIO data channel.
10 DIO Port 1 (2) Bidirectional SE DIO data channel.
11 GND Ground reference for signals.
12 DIO Port 1 (3) Bidirectional SE DIO data channel.
13 PFI 0 Bidirectional SE DIO data channel.
14 NC No connect.
15 PFI 1 Bidirectional SE DIO data channel.
16 PFI 2 Bidirectional SE DIO data channel.
17 GND Ground reference for signals.
18 +5 V +5 V power (10 mA maximum).
19 PFI 3 Bidirectional SE DIO data channel.
Caution The AUX I/O connector accepts a standard, third-party HDMI cable, but
the AUX I/O port is not an HDMI interface. Do not connect the AUX I/O port on the
8| ni.com | NI 5783 Getting Started Guide

NI 5783 to the HDMI port of another device. NI is not liable for any damage
resulting from such signal connections.
Related Information
Accessories on page 6
The NI 5783 can be used with the SCB-19 shielded desktop connector block.
Block Diagram
The following figure shows the NI 5783 block diagram and signal flow.
Figure 1. NI 5783 Block Diagram
CH0 AI
CH1 AI
40 MHz
Anti-Alias
ADA4932
Analog Input
85 MHz
Noise Filter
CH2 AI
CH3 AI
TRIG IN/OUT
CLOCK_REF IN
Buffered Trigger I/O To FPGA Interface
10/100 MHz CMOS Clock
CH0 A0 MCX
CH1 A0 MCX
CH2 A0 MCX
CH3 A0 MCX
+
–
40 MHz
Anti-Alias
ADA4932 85 MHz
Noise Filter
+
–
40 MHz
Anti-Alias
ADA4932 85 MHz
Noise Filter
+
–
40 MHz
Anti-Alias
ADA4932 85 MHz
Noise Filter
+
–
+
–
40 MHz AA LMH6702
+
–
40 MHz AA LMH6702
+
–
40 MHz AA LMH6702
+
–
40 MHz AA LMH6702
Analog Input
Clocking
100 MHz LVPECL CLK
100 MHz LVPECL CLK
100 MHz LVDS CLK
DACCLK/8 OSTR LVPECL 100 MHz
VCXO
Loop-Filter
(PLL)
Phase/Freq
Adjust DAC
Ch A+
Ch A+
DACCLK
DATACLK =
2”DACCLK
Ch A Ch B Ch C Ch D
Ch B+
Ch B+ DAC3484
QUAD 16-bit
1.25 GSPS DAC
AD9511
Clock Distribution
& PLL
1 W Max
Power Supplies
(100 MS/s Data Rate
Interpolate x8 for
Fixed Fdac of 800 MS/S
with Internal PLL)
Ch C+
Ch C+
Ch D+
Ch D+
Ch A+
HDMI DIO
Ch A+
DATACLK =
4”SAMPLECLK
SAMPLECLK
Ch B+
Ch B+ AD9653
QUAD 16-bit
125 MSPS ADC
(Clock at 100 MS/S)
Ch C+
Ch C+
Ch D+
Ch D+
Ch A1
Ch B0
Ch B1
Ch C0
Ch C1
Ch D0
Ch D1
A(15) A(13) A(11) A(9) Ch A0
A(14) A(12) A(10) A(8)
Typ: 4.6 W
Abs Max: 5.5 W
RSS Max: 5.3 W
+/– 4.5 V
+ 1.8 AVDD
+ 1.2 V
+ 3.8 V
+ 3.3 AVDD+ 1.8 DVDD
Inrush Limiter
Inrush Limiter
400 MHz DDR (800 Mb/S)
DIO
16 BIT LVDS 400 MHz DDR (800 Mb/S)
400 MHz DDR (800 Mb/S)
400 MHz DDR (800 Mb/S)
400 MHz DDR (800 Mb/S)
400 MHz DDR (800 Mb/S)
400 MHz DDR (800 Mb/S)
400 MHz DDR (800 Mb/S)
400 MHz DDR (800 Mb/S)
FLEXRIO
SIGNAL REQ
ADC = 25
DAC = 50
PLL = 10
DIO? = 16
TOTAL = 103
+ 12 V
+ 3.3 V
OR + Vcco
+ VccoB
+ VccoA
TB_Ref_CLK/PXI_10
GPIO
VccoA = VccoB = Vcco = 2.5 V
Logic Diagram
The following diagram shows the NI 5783 logic layout.
NI 5783 Getting Started Guide | © National Instruments | 9