National Instruments 7932 User manual

NI-7932
2022-07-06

Contents
GSG Purpose. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
FlexRIO Documentation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Safety Guidelines. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Electromagnetic Compatibility Guidelines. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Verifying the System Requirements. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
What You Need to Get Started. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Unpacking the Kit. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Preparing the Environment. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Wiring Power to the NI-7932R. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Powering on the NI-7932R. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
STATUS LED. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Connecting the NI-7932R to the Host Computer. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Installing the FlexRIO Adapter Module. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Configuring the System in Measurement & Automation Explorer (MAX). . . . . . . . . . . 11
Setting a System Password. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Installing Soware on the NI-7932R. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Adding the NI-7932R to a LabVIEW Project. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Adding a FlexRIO Adapter Module to the Target. . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Programming Options. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Programming with LabVIEW. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Text-based Programming. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Removing the Adapter Module. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Troubleshooting the NI-7932R. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Why Can't the NI-7932R Communicate with the Network?. . . . . . . . . . . . . . . . . . 16
Why Doesn't the Device Appear in MAX?. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Appendix: Front Panel. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
NI-7932R Front Panel. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
Worldwide Support and Services. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
Where to Go Next. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
ni.com
2
NI-7932

GSG Purpose
This document describes how to begin using the NI-7932R.
Figure 1. NI-7932R
Related information
■http://www.ni.com/manuals
FlexRIO Documentation
Document Location Description
Getting started guide
for your controller for
FlexRIO
Available from the Start menu and
at ni.com/manuals.
Contains installation instructions for
your FlexRIO system.
Specifications
document for your
controller for FlexRIO
Available from the Start menu and
at ni.com/manuals.
Contains specifications for your
controller for FlexRIO.
Getting started guide
for your adapter
module
Available from the Start menu and
at ni.com/manuals.
Contains signal information,
examples, and CLIP details for your
adapter module.
Specifications
document for your
adapter module
Available from the Start menu and
at ni.com/manuals.
Contains specifications for your
adapter module.
© National Instruments 3
NI-7932

Document Location Description
LabVIEW FPGA
Module Help
Embedded in LabVIEW Help and
at ni.com/manuals.
Contains information about the basic
functionality of the LabVIEW FPGA
Module.
Real-Time Module
Help
Embedded in LabVIEW Help and
at ni.com/manuals.
Contains information about real-time
programming concepts, step-by-step
instructions for using LabVIEW with
the Real-Time Module, reference
information about Real-Time Module
VIs and functions, and information
about LabVIEW features on real-time
operating systems.
FlexRIO Help Available from the Start menu and
at ni.com/manuals.
Contains information about the FPGA
module front panel connectors and
I/O, controller for FlexRIO front panel
connectors and I/O, programming
instructions, and adapter module
component-level IP (CLIP).
FlexRIO Adapter
Module
Development Kit
User Manual
Available from the Start menu at
Start » All Programs » National
Instruments » NI FlexRIO » NI
FlexRIO Adapter Module
Development Kit » Documentation.
Contains information about how to
create custom adapter modules for
use with FlexRIO FPGA modules.
LabVIEW Examples Available in NI Example Finder. In
LabVIEW, click Help » Find
Examples » Hardware Input and
Output » FlexRIO.
Contains examples of how to run
FPGA VIs and Host VIs on your device.
IPNet Located at ni.com/ipnet. Contains LabVIEW FPGA functions and
intellectual property to share.
FlexRIO product page Located at ni.com/flexrio. Contains product information and
data sheets for FlexRIO devices.
Table 1. FlexRIO Documentation Locations and Descriptions
ni.com
4
NI-7932

Safety Guidelines
Caution You can impair the protection provided by the NI-7932R if you
use it in a manner not described in this document.
Electromagnetic Compatibility Guidelines
This product was tested and complies with the regulatory requirements and limits
for electromagnetic compatibility (EMC) stated in the product specifications. These
requirements and limits provide reasonable protection against harmful interference
when the product is operated in the intended operational electromagnetic
environment.
This product is intended for use in industrial locations. However, harmful
interference may occur in some installations, when the product is connected to a
peripheral device or test object, or if the product is used in residential or
commercial areas. To minimize interference with radio and television reception and
prevent unacceptable performance degradation, install and use this product in strict
accordance with the instructions in the product documentation.
Furthermore, any changes or modifications to the product not expressly approved
by National Instruments could void your authority to operate it under your local
regulatory rules.
Caution To ensure the specified EMC performance, operate this product
only with shielded cables and accessories. The DC power input cables and
optical SFP+ cables may be unshielded.
Caution To ensure the specified EMC performance, you must use an
isolated cable with the SFP+ ports.
Caution To ensure the specified EMC performance, the length of any
cable connected to the TRIG ports and REF CLK ports must be no longer
than 3 m (10 ). The length of copper cables connected to the SFP+ ports
must be no longer than 3 m (10 ). The length of cables connected to the
© National Instruments 5
NI-7932

USB device ports or host ports must be no longer than 30 m (100 ). The
lengths of Ethernet cables and optical SFP+ cables are not limited.
Caution The USB device port is intended only for use in device
configuration, application deployment, debug, and maintenance.
Verifying the System Requirements
To use the NI-7932R, your system must meet certain requirements. For more
information about minimum system requirements, recommended system, and
supported application development environments (ADEs), refer to the readme,
which is available on the soware media or online at ni.com/updates.
What You Need to Get Started
■The NI-7932R shipping kit, which includes the following components:
■The NI-7932R device
■FlexRIO Support DVD
Note FlexRIO Support 15.1 is the earliest supported driver for the
NI-7932R.
■NI-7932R Getting Started Guide (this document)
■Power screw terminal connector plug
■A to Mini-B device port USB cable
■A host computer running Windows, with NI soware installed in the
following order:
Note Visit ni.com/info and enter the Info Code rdsowareversion to
determine which soware versions you need to use the NI-7932R
and supported FlexRIO adapter modules.
■LabVIEW
ni.com
6
NI-7932

■LabVIEW Real-Time
■LabVIEW FPGA
■FlexRIO Support[1]
■A DC power supply as described in the NI-7932R Specifications
■A FlexRIO adapter module or custom adapter module (optional)
■A number 2 Phillips screwdriver
■A number 1 Phillips screwdriver
■A small flat-blade screwdriver
■Straight through shielded Ethernet cable (if connecting to a network) or
crossover shielded Ethernet cable (if connecting directly to a PC)
1 LabVIEW 2015, FlexRIO Support 2015, LabVIEW Real-Time 2015, and LabVIEW FPGA
2015 are the earliest versions of soware that support the NI-7932R.
Unpacking the Kit
Caution To prevent electrostatic discharge (ESD) from damaging the
device, ground yourself using a grounding strap or by holding a grounded
object, such as your computer chassis.
1. Touch the antistatic package to a metal part of the computer chassis.
2. Remove the device from the package and inspect the device for loose
components or any other sign of damage.
Caution Never touch the exposed pins of connectors.
Note Do not install a device if it appears damaged in any way.
3. Unpack any other items and documentation from the kit.
Store the device in the antistatic package when the device is not in use.
© National Instruments 7
NI-7932

Preparing the Environment
Ensure that the environment you are using the NI-7932R in meets the following
specifications.
Operating temperature (IEC 60068-2-1, IEC 60068-2-2) 0 °C to 55 °C
Operating humidity (IEC 60068-2-56) 10% to 90% RH, noncondensing
Pollution Degree 2
Maximum altitude 2,000 m at 25 °C ambient temperature
Indoor use only.
Note Refer to the NI-7932R Specifications at ni.com/manuals for
complete specifications.
Caution Clean the hardware with a so, nonmetallic brush. Make sure
that the hardware is completely dry and free from contaminants before
returning it to service.
Wiring Power to the NI-7932R
The NI-7932R requires a 9 V to 30 V external power supply that meets the
specifications in the NI-7932R Specifications. The NI-7932R filters and regulates
the supplied power and provides power for the I/O modules.
Note You can latch the power plug to the NI-7932R using two screws
tightened to 0.20 to 0.25 N · m (1.8 to 2.2 lb · in.) of torque.
The maximum wire gage accepted by the power connector plug is 16 AWG. You must
use a stripped wire length of 10 mm (.394 in).
When the POWER LED on the front panel is lit green, the device is powered.
The NI-7932R has reverse-voltage protection.
Complete the following steps to connect a power supply to the NI-7932R.
1. Ensure the power source is turned o.
ni.com
8
NI-7932

2. Connect a positive wire to the positive terminal of the power connector plug,
and connect a negative wire to the negative terminal of the power connector
plug.
12
3
1. Positive terminal
2. Negative terminal
3. No connect
3. Install the power connector on the front panel of the NI-7932R.
4. Turn on the external power source(s).
Powering on the NI-7932R
When you apply power for the first time to the NI-7932R, the controller boots into
safe mode. The POWER LED illuminates, the STATUS LED illuminates briefly, and
then the STATUS LED blinks twice every few seconds.
Aer you install soware on the controller, subsequent reboots will boot the
controller into the NI Linux Real-Time operating system.
You can optionally configure the NI-7932R to launch an embedded stand-alone
LabVIEW Real-Time application each time you boot the controller.
STATUS LED
The STATUS LED is o during normal operation. The NI-7932R indicates specific
error conditions by flashing the STATUS LED a certain number of times every few
seconds, as shown in the following table.
LED State Indication
2 flashes every few
seconds
There is no soware installed, which is the out-of-box state, or the controller
has detected an error in its soware.
An error can occur when an attempt to upgrade the soware is interrupted.
Refer to the MAX Help for information about reinstalling soware on the
controller.
© National Instruments 9
NI-7932

LED State Indication
3 flashes every few
seconds
The controller is in safe mode. Refer to the MAX Help for information about
safe mode.
4 flashes every few
seconds
The soware has crashed twice without rebooting or cycling power between
crashes. This usually occurs when the controller runs out of memory.
Review your Real-Time VI and check the memory usage. Modify the VI as
necessary to solve the memory usage issue.
Continuously
flashing
The controller has not booted into NI Linux Real-Time. The controller either
booted into an unsupported operating system, was interrupted during the
boot process, or detected an unrecoverable soware error.
Solid The controller is booting up.
Continuously
flashing
This indicates a hardware error. An internal power supply has failed. Check
front-panel I/O and adapter module connections for shorts. Remove any
shorts and power cycle the controller. If the problem persists, contact
National Instruments.
O Normal operation.
Connecting the NI-7932R to the Host Computer
Complete the following steps to connect the NI-7932R to the host computer using
the USB device port.
1. Power on the host computer.
2. Connect the NI-7932R to the host computer using the USB A-to-B cable.
Note Alternatively, you can use the RJ-45 Ethernet port to connect
the NI-7932R to the host computer.
The device driver soware automatically detects the NI-7932R. If the device
driver soware does not detect the NI-7932R, verify that you installed the
appropriate NI soware in the correct order on the host computer.
ni.com
10
NI-7932

Tip You can also use the Ethernet port to connect directly to the host
computer or network. Refer to the user manual on ni.com/manuals for
more information about Ethernet connections.
Related concepts
■Troubleshooting the NI-7932R
Installing the FlexRIO Adapter Module
Skip this section if you are not using a FlexRIO adapter module.
1. Gently insert the guide pins and the high-density card edge of the FlexRIO
adapter module into the corresponding connectors of the NI-7932R.
The connection may be tight, but do not force the adapter module into place.
2. Tighten the captive screws on the FlexRIO adapter module to secure it to the
NI-7932R.
The following figure shows the NI-7932R with the FlexRIO adapter module
connected.
Figure 1. NI-7932R with FlexRIO Adapter Module
Refer to the getting started guide for your adapter module for more information
about your adapter module, including programming information.
© National Instruments 11
NI-7932

Configuring the System in Measurement & Automation
Explorer (MAX)
Aer connecting the NI-7932R to the host computer, complete the following steps to
configure the system for the first time in MAX.
1. Launch MAX on the host computer.
2. Expand Remote Systems in the MAX configuration tree and select the system.
MAX lists the system as the model name followed by the serial number, such
as NI-7932R-030521C9.
Related reference
■Why Doesn't the Device Appear in MAX?
Setting a System Password
Complete the following steps to set a system password.
Note Setting a system password is optional.
Note The default username for the NI-7932R is admin. There is no default
password for the NI-7932R, so you must leave the password field blank
when logging in until you set a system password.
1. Right-click your system and select Web Configuration.
The NI Web-Based Configuration and Monitoring utility opens in your default
browser and is where you set the password. If you have not installed Microso
Silverlight, NI Web-based Configuration & Monitoring prompts you to do so.
2. Enter a unique name for your system in the Hostname field.
3. Click the Security Configuration icon.
4. Click Login.
5. In the Login dialog box, enter the username admin and leave the password
field blank.
ni.com
12
NI-7932

6. Click OK.
7. Click Change Password.
8. Enter and re-enter a new password.
9. Click OK.
10. Click Save.
11. Click OK to confirm you are changing the password.
Caution NI cannot recover lost system passwords. If you forget the
password, you must contact NI and reformat the controller.
Installing Soware on the NI-7932R
1. Open Measurement & Automation Explorer (MAX).
2. Expand the system under Remote Systems by clicking the arrow beside it.
3. Select Software.
4. Click Add/Remove Software at the top of the Software tab to launch the
LabVIEW Real-Time Soware Wizard.
Note A login window appears if you set a system password.
5. Select a recommended soware set to install.
6. Click Next.
7. The recommended soware set is preselected from the list of soware add-
ons. Check any additional soware add-ons you want. The System State
Publisher, for example, makes monitoring system performance simple.
Note You can use the LabVIEW Real-Time Soware Wizard to install
more soware add-ons later. The FlexRIO 15.0 Recommended
Soware Set is enough to get started.
8. Click Next.
9. Review the summary of soware to install. Click Next to begin the update.
© National Instruments 13
NI-7932

10. Wait for the installation to finish, and then click Finish.
Adding the NI-7932R to a LabVIEW Project
1. Launch LabVIEW. The LabVIEW Getting Started window appears.
2. Click Create Project or open an existing project.
3. Right-click the project root in the Project Explorer window and select New »
Targets and Devices from the shortcut menu to display the Add Targets and
Devices dialog box.
1. If the hardware is connected to the host, select Existing target or device.
Select the NI-7932R under Real-Time FlexRIO and click OK.
2. If the hardware is not connected to the host, select New target or
device. Select the NI-7932R under Real-Time FlexRIO and click OK.
4. Right-click the target and select New » FPGA Target.
The FPGA target appears in the project under the Real-Time target.
Adding a FlexRIO Adapter Module to the Target
Skip this section if you are not using an adapter module.
1. Expand the FPGA target by clicking the + button, then right-click IO Module
and select Properties.
2. Select the General category and check the Enable IO Module box.
3. Select your I/O module from the IO Modules list, and select the CLIP you want
to use from the Component Level IP box.
4. Click OK.
Programming Options
Refer to the following table for information about how to program the NI-7932R.
Component Programming Option(s)
Real-Time controller LabVIEW Real-Time or C/C++ Development Tools for NI Linux Real-Time,
Eclipse Edition.
ni.com
14
NI-7932

Component Programming Option(s)
FPGA LabVIEW FPGA
Related information
■http://www.ni.com/manuals/
■http://www.ni.com/tutorial/14625/en/
Programming with LabVIEW
The Controller for FlexRIO examples provide a starting point for programming with
LabVIEW. To access these examples, open LabVIEW and select Help » Find Examples »
Hardware Input and Output » Controller for FlexRIO.
For more detailed instructions about programming the NI-7932R with LabVIEW, refer
to the NI-7931R/7932R/7935R User Manual.
Text-based Programming
You can target the NI-7932R Linux Real-Time operating system from text-based
development environments such as C and C++.
Removing the Adapter Module
Complete the following steps to remove an adapter module from the NI-7932R.
1. Disconnect all cables to the adapter module.
2. Power o the NI-7932R.[1]
3. Unscrew the adapter module.
4. Remove the adapter module.
1 If you cannot power down the NI-7932R, use the System Configuration application
programming interface (API) to disable power to the adapter module.
Troubleshooting the NI-7932R
Related tasks
© National Instruments 15
NI-7932

■Connecting the NI-7932R to the Host Computer
Why Can't the NI-7932R Communicate with the Network?
1. Connect cables from your device to the host computer.
1. If you are using the USB port, use a USB cable to connect the NI-7932R
USB device port to a host computer.
The USB driver creates a virtual network interface and assigns an IP
address to the NI-7932R in the format of 172.22.11.x.
2. If you are using the ethernet port, use an ethernet to connect the
ethernet port to the host computer.
2. In MAX, expand your system under Remote Systems.
3. Select the Network Settings tab to configure the IP and other network
settings.
4. (Optional) Use the RJ-45 Ethernet port 1 to reconnect the NI-7932R to the host
computer. The NI-7932R attempts to initiate a DHCP network connection at
powerup.
If the NI-7932R cannot contain an IP address, it connects to the network with a
link-local IP address with the form 169.254.x.x. The host computer
communicates with the NI-7932R over a standard Ethernet connection.
Why Doesn't the Device Appear in MAX?
If you cannot find the NI-7932R in MAX, complete the following steps.
■
Ensure you have the correct version of FlexRIO Support installed on the host
computer.
■Check the USB cable connections at the NI-7932R and host computer. Check
the Ethernet cable connections at the host computer and router.
■
If you have network firewalls or other security soware enabled, try
temporarily turning them o. You may also need to add an exception for MAX.
In Windows 7, select Start » Control Panel » System and Security » Windows
ni.com
16
NI-7932

Firewall » Allow a program through Windows Firewall. Click Allow another
program, select Measurement & Automation, click Add, then click OK.
■Ensure that UDP port 44525 is open to communication on the host
computer. If you are using an intelligent switch on the network, ensure that it
is not disabling UDP port 44525.
■Hold down the RESET button for 5 seconds to reboot the target into safe
mode. This prevents a real-time app from running. Sometimes a
malfunctioning real-time app prevents network communication.
■Check the Device Manager to ensure the National Instruments USBLAN
adapter is recognized. In Windows 7, select Start » Control Panel » Device
Manager » Network adapters » National Instruments » USBLAN adapter. If the
USBLAN adapter is not recognized, you must reinstall FlexRIO Support.
■Ensure that the Ethernet cable is connected correctly.
Related tasks
■Configuring the System in Measurement & Automation Explorer (MAX)
NI-7932R Front Panel
The following figure shows the NI-7932R front panel connectors, buttons, and LEDs.
© National Instruments 17
NI-7932

Figure 3. NI-7932R
11
7
34 6
9
5 8
21
10
1. TRIG
2. REF CLK
3. Storage (µSD card)
4. USB device port
5. USB host
6. 1 Gigabit Ethernet
7. LED indicators
8. Reset
9. DC power source
10. FlexRIO adapter module connector
11. Port 0/Port 1 (SFP+ connectors)
Related information
■http://www.ni.com/manuals/
LED Indicators
The following figure shows the NI-7932R LEDs in more detail.
ni.com
18
NI-7932

Figure 4. NI-7932R LEDs
RT User
LED
Power
LED
Status
LED
FPGA User
LED
NI-7932R Module Signals
The following figure shows the available signals on the NI-7932R.
Bank 0
PCB
Primary Side
+3.3V
SCL
TB_Present
+12V
Vcco
RSVD
GND
IOModSyncClk_n
IOModSyncClk
GND
GPIO_0_n
GPIO_0
GND
GPIO_1_n
GPIO_1
GND
GPIO_CC_2_n
GPIO_CC_2
GND
GPIO_3_n
GPIO_3
GND
GPIO_4_n
GPIO_4
GND
GPIO_5_n
GPIO_5
GND
GPIO_6_n
GPIO_6
GND
GPIO_7_n
GPIO_7
GND
GPIO_8_n
GPIO_8
GND
GPIO_9_n
GPIO_9
GND
GPIO_10_n
GPIO_10
GND
GPIO_11_n
GPIO_11
GND
GPIO_12_n
GPIO_12
GND
GND
GPIO_13_n
GPIO_13
P2
P1
S148
S147
S146
S145
S144
S143
G36
S142
S141
G35
S140
S139
G34
S138
S137
G33
S136
S135
G32
S134
S133
G31
S132
S131
G30
S130
S129
G29
S128
S127
G28
S126
S125
G27
S124
S123
G26
S122
S121
G25
S120
S119
G24
S118
S117
G23
S116
S115
G22
G37
P2
P1
S74
S73
S72
S71
S70
S69
G36
S68
S67
G35
S66
S65
G34
S64
S63
G33
S62
S61
G32
S60
S59
G31
S58
S57
G30
S56
S55
G29
S54
S53
G28
S52
S51
G27
S50
S49
G26
S48
S47
G25
S46
S45
G24
S44
S43
G23
S42
S41
G22
G37
+12V
+3.3V
SDA
TB_Power_Good
Vcco
Veeprom
TDC_Assert_CLK_n
TDC_Assert_CLK
GND
GPIO_24_n
GPIO_24
GND
GPIO_25_n
GPIO_25
GND
GPIO_CC_26_n
GPIO_CC_26
GND
GPIO_27_n
GPIO_27
GND
GPIO_28_n
GPIO_ 28
GND
GPIO_29_n
GPIO_29
GND
GPIO_30_n
GPIO_30
GND
GPIO_31_n
GPIO_31
GND
GPIO_32_n
GPIO_32
GND
GPIO_33_n
GPIO_33
GND
GPIO_34_n
GPIO_34
GND
GPIO_35_n
GPIO_35
GND
GPIO_36_n
GPIO_36
GND
GPIO_37_n
GPIO_37
GND
GND
PCB
Secondary Side
Bank 1
PCB
Primary Side
GND
GPIO_CC_14_n
GPIO_CC_14
GND
GPIO_15_n
GPIO_15
GND
GPIO_16_n
GPIO_16
GND
GPIO_17_n
GPIO_17
GND
GPIO_18_n
GPIO_18
GND
GPIO_19_n
GPIO_19
GND
GPIO_20_n
GPIO_20
GND
GPIO_21_n
GPIO_21
GND
GPIO_22_n
GPIO_22
GND
GPIO_23_n
GPIO_23
GND
GPIO_58_n
GPIO_58
GND
GPIO_59_n
GPIO_59
GND
GPIO_CC_60_n
GPIO_CC_60
GND
GPIO_61_n
GPIO_61
GND
GPIO_62_n
GPIO_62
GND
GPIO_63_n
GPIO_63
GND
GND
GPIO_64_n
GPIO_64
GPIO_65_n
GPIO_65
GND
GPIO_66_n
GPIO_67_n
GPIO_66
GND
GND
GPIO_67
G20
G21
S114
S113
S112
S111
S110
S109
G18
S108
S107
G17
S106
S105
G16
S104
S103
G15
S102
S101
G14
S100
S99
G13
S98
S97
G12
S96
S95
G11
S94
S93
G10
S92
S91
G9
S90
S89
G8
S88
S87
G7
S86
S85
G6
S84
S83
G5
S82
S81
G4
G19
S80
S79
G3
S78
S77
G2
S76
S75
G1
G20
G21
S40
S39
S38
S37
S36
S35
G18
S34
S33
G17
S32
S31
G16
S30
S29
G15
S28
S27
G14
S26
S25
G13
S24
S23
G12
S22
S21
G11
S20
S19
G10
S18
S17
G9
S16
S15
G8
S14
S13
G7
S12
S11
G6
S10
S9
G5
S8
S7
G4
G19
S6
S5
G3
S4
S3
G2
S2
S1
G1
GND
GND
GPIO_CC_38_n
GPIO_CC_38
GPIO_39_n
GPIO_39
GPIO_40_n
GPIO_40
GND
GPIO_41_n
GPIO_41
GND
GPIO_42_n
GPIO_42
GND
GPIO_43_n
GPIO_43
GND
GPIO_44_n
GPIO_44
GND
GPIO_45_n
GPIO_45
GND
GPIO_46_n
GPIO_46
GND
GPIO_47_n
GPIO_47
GND
GPIO_48_n
GPIO_48
GND
GPIO_49_n
GPIO_49
GND
GPIO_CC_50_n
GPIO_CC_50
GND
GPIO_51_n
GPIO_51
GND
GPIO_52_n
GPIO_52
GND
GPIO_53_n
GPIO_53
GND
GPIO_54_n
GPIO_54
GND
GPIO_55_n
GPIO_55
GND
GPIO_56_n
GPIO_56
GND
GPIO_57_n
GPIO_57
GND
GND
PCB
Secondary Side
Bank 2
Bank 0
Bank 2 Bank 1
© National Instruments 19
NI-7932

Worldwide Support and Services
The National Instruments website is your complete resource for technical support.
At ni.com/support, you have access to everything from troubleshooting and
application development self-help resources to email and phone assistance from NI
Application Engineers.
Visit ni.com/services for NI Factory Installation Services, repairs, extended warranty,
and other services.
Visit ni.com/register to register your National Instruments product. Product
registration facilitates technical support and ensures that you receive important
information updates from NI.
A Declaration of Conformity (DoC) is our claim of compliance with the Council of the
European Communities using the manufacturer’s declaration of conformity. This
system aords the user protection for electromagnetic compatibility (EMC) and
product safety. You can obtain the DoC for your product by visiting ni.com/
certification. If your product supports calibration, you can obtain the calibration
certificate for your product at ni.com/calibration.
National Instruments corporate headquarters is located at
11500 North Mopac Expressway, Austin, Texas, 78759-3504. National Instruments
also has oices located around the world. For telephone support in the United
States, create your service request at ni.com/support or dial 1 866 ASK MYNI
(275 6964). For telephone support outside the United States, visit the Worldwide
Oices section of ni.com/niglobal to access the branch oice websites, which
provide up-to-date contact information, support phone numbers, email addresses,
and current events.
Where to Go Next
Refer to the following figure for information about other product tasks and
associated resources for those tasks.
ni.com
20
NI-7932