National Instruments PXIe-5763 User manual

PXIe-5763

GETTING STARTED GUIDE
PXIe-5763
PXI FlexRIO Digitizer
Note Before you begin, install and configure your chassis and controller.
This document explains how to install, configure, test, and use the PXIe-5763. You can
program the PXIe-5763 with the following software options.
• FlexRIO Support driver software
• NI LabVIEW Instrument Design Libraries for FlexRIO (instrument design libraries)
Note Adapter modules are not installable or interchangeable on PXIe-5763
devices.
Caution This icon denotes a caution, which advises you to consult documentation
where this symbol is marked.
Contents
Safety Guidelines...................................................................................................................... 2
Electromagnetic Compatibility Guidelines...............................................................................2
FlexRIO Documentation and Resources...................................................................................2
Verifying the System Requirements..........................................................................................3
Unpacking the Kit..................................................................................................................... 3
PXIe-5763 Kit Contents............................................................................................................4
Preparing the Environment....................................................................................................... 4
Installing the Application Software and Driver........................................................................ 4
Installing the PXIe-5763........................................................................................................... 5
PXIe-5763 Front Panel..............................................................................................................6
Configuring the PXIe-5763 in MAX........................................................................................ 8
FlexRIO Examples....................................................................................................................9
Accessing FlexRIO Examples.......................................................................................... 9
Block Diagram.......................................................................................................................... 9
Component-Level Intellectual Property (CLIP)......................................................................11
PXIe-5763 CLIP............................................................................................................. 12
Making a Measurement...........................................................................................................12
Making a Measurement with LabVIEW.........................................................................12
Troubleshooting...................................................................................................................... 12
What Should I Do if the PXIe-5763 Doesn't Appear in MAX?......................................12
What Should I Do if the PXIe-5763 Fails the Self-Test?................................................13

Where to Go Next................................................................................................................... 13
Worldwide Support and Services............................................................................................ 13
Safety Guidelines
Caution You can impair the protection provided by the PXIe-5763 if you use it in
a manner not described in this document.
Electromagnetic Compatibility Guidelines
This product was tested and complies with the regulatory requirements and limits for
electromagnetic compatibility (EMC) stated in the product specifications. These requirements
and limits provide reasonable protection against harmful interference when the product is
operated in the intended operational electromagnetic environment.
This product is intended for use in industrial locations. However, harmful interference may
occur in some installations, when the product is connected to a peripheral device or test object,
or if the product is used in residential or commercial areas. To minimize interference with
radio and television reception and prevent unacceptable performance degradation, install and
use this product in strict accordance with the instructions in the product documentation.
Furthermore, any changes or modifications to the product not expressly approved by National
Instruments could void your authority to operate it under your local regulatory rules.
FlexRIO Documentation and Resources
Table 1. FlexRIO Documentation and Resources
Document/Resource Location Description
PXIe-5763 Getting
Started Guide (this
document)
Available from the Start menu
and at ni.com/manuals.
Contains installation instructions
and basic programming instructions
for your PXIe-5763.
PXIe-5763
Specifications
Available from the Start menu
and at ni.com/manuals.
Contains specifications for your
PXIe-5763.
LabVIEW FPGA
Module Help
Embedded in LabVIEW Help
and at ni.com/manuals.
Contains information about the
basic functionality of the LabVIEW
FPGA Module.
2| ni.com | PXIe-5763 Getting Started Guide

Table 1. FlexRIO Documentation and Resources (Continued)
Document/Resource Location Description
FlexRIO Help Available from the Start menu
and at ni.com/manuals.
Contains information about the
FPGA module front panel
connectors and I/O, programming
instructions, and I/O component-
level IP (CLIP).
LabVIEW Examples Available in NI Example
Finder. In LabVIEW, click
Help»Find Examples»
Hardware Input and
Output»FlexRIO.
Contains examples of how to run
FPGA VIs and Host VIs on your
device.
IPNet Located at ni.com/ipnet. Contains LabVIEW FPGA
functions and intellectual property
to share.
FlexRIO product page Located at ni.com/flexrio. Contains product information and
data sheets for FlexRIO devices.
Verifying the System Requirements
To use the PXIe-5763, your system must meet certain requirements. For more information
about minimum system requirements, recommended system, and supported application
development environments (ADEs), refer to the readme, which is available on the software
media or online at ni.com/updates.
Unpacking the Kit
Caution To prevent electrostatic discharge (ESD) from damaging the device,
ground yourself using a grounding strap or by holding a grounded object, such as
your computer chassis.
1. Touch the antistatic package to a metal part of the computer chassis.
2. Remove the device from the package and inspect the device for loose components or any
other sign of damage.
Caution Never touch the exposed pins of connectors.
Note Do not install a device if it appears damaged in any way.
3. Unpack any other items and documentation from the kit.
PXIe-5763 Getting Started Guide | © National Instruments | 3

Store the device in the antistatic package when the device is not in use.
PXIe-5763 Kit Contents
The following items are included in the device kit:
• The PXIe-5763
• The FlexRIO Support driver software media
• Documentation:
–Maintain Forced-Air Cooling Note to Users
–PXIe-5763 Getting Started Guide (this document)
Preparing the Environment
Ensure the environment in which you are using the PXIe-5763 meets the following
specifications.
Operating environment
Ambient temperature range 0 °C to 45 °C (Tested in accordance with
IEC-60068-2-1 and IEC-60068-2-2. Meets
MIL-PRF-28800F Class 3 low temperature
limit and MIL-PRF-28800F Class 4 high
temperature limit.)
Relative humidity range 10% to 90%, noncondensing (Tested in
accordance with IEC 60068-2-56.)
Maximum altitude 2,000 m (800 mbar) (at 25 °C ambient
temperature)
Pollution Degree 2
Indoor use only.
Note For complete specifications, refer to the specifications document for your
device at ni.com/manuals.
Installing the Application Software and Driver
Before installing your hardware, you must install the application software and instrument
driver. Visit NI FlexRIO Driver Supported Versions for FlexRIO Adapters and Modules to
determine which minimum software versions you need for your device. Install the software in
the following order:
1. Install LabVIEW.
4| ni.com | PXIe-5763 Getting Started Guide

Refer to the LabVIEW Installation Guide for installation instructions for LabVIEW and
system requirements for the LabVIEW software. Refer to the LabVIEW Upgrade Notes
for additional information about upgrading to the most recent version of LabVIEW for
Windows. Documentation for LabVIEW is available at ni.com/manuals and by selecting
Start»All Programs»National Instruments»LabVIEW»LabVIEW Manuals.
2. Install the LabVIEW FPGA Module.
Refer to the LabVIEW FPGA Module Release and Upgrade Notes for installation
instructions and information about getting started with the LabVIEW FPGA Module.
Documentation for the LabVIEW FPGA Module is available at ni.com/manuals and by
selecting Start»All Programs»National Instruments»LabVIEW»LabVIEW
Manuals.
3. Install FlexRIO Support.
Refer to the FlexRIO Readme on the FlexRIO installation media for system requirements
and installation instructions for FlexRIO Support. Documentation for FlexRIO Support is
available at ni.com/manuals and by selecting Start»All Programs»National
Instruments»NI FlexRIO.
Installing the PXIe-5763
Caution To prevent damage to the PXIe-5763 caused by ESD or contamination,
handle the module using the edges or the metal bracket.
1. Ensure the AC power source is connected to the chassis before installing the module.
The AC power cord grounds the chassis and protects it from electrical damage while you
install the module.
2. Power off the chassis.
3. Inspect the slot pins on the chassis backplane for any bends or damage prior to
installation. Do not install a module if the backplane is damaged.
4. Remove the black plastic covers from all the captive screws on the module front panel.
5. Identify a supported slot in the chassis. The following figure shows the symbols that
indicate the slot types.
Figure 1. Chassis Compatibility Symbols
NI PXIe-1062Q
12 3 45
1. PXI Express System Controller Slot
2. PXI Peripheral Slot
3. PXI Express Hybrid Peripheral Slot
4. PXI Express System Timing Slot
5. PXI Express Peripheral Slot
PXIe-5763 modules can be placed in PXI Express peripheral slots, PXI Express hybrid
peripheral slots, or PXI Express system timing slots.
PXIe-5763 Getting Started Guide | © National Instruments | 5

6. Touch any metal part of the chassis to discharge static electricity.
7. Ensure that the ejector handle is in the downward (unlatched) position.
8. Place the module edges into the module guides at the top and bottom of the chassis. Slide
the module into the slot until it is fully inserted.
Figure 2. Module Installation
2
3
NI PXIe-1075
1
1. Chassis
2. Hardware Module
3. Ejector Handle in Downward (Unlatched) Position
9. Latch the module in place by pulling up on the ejector handle.
10. Secure the module front panel to the chassis using the front-panel mounting screws.
Note Tightening the top and bottom mounting screws increases mechanical
stability and also electrically connects the front panel to the chassis, which can
improve the signal quality and electromagnetic performance.
11. Cover all empty slots using EMC filler panels or fill using slot blockers to maximize
cooling air flow, depending on your application.
12. Power on the chassis.
PXIe-5763 Front Panel
The following figure shows the PXIe-5763 front panel.
6| ni.com | PXIe-5763 Getting Started Guide

Figure 3. PXIe-5763 Front Panel
PXIe-5763
FlexRIO Digitizer
DIO
16-Bit, 500 MS/s
4 Vpp
MAX
AI 0
AI 1
AI 2
AI 3
REF/
CLK
IN
The following table describes the signal connections for the PXIe-5763.
PXIe-5763 Getting Started Guide | © National Instruments | 7

Connector Description Function
DIO Molex™ Nano-Pitch DIO
connector
Multi-signal DIO connector that provides
access to FPGA multi-gigabit transceivers
(MGTs)1 and general-purpose input/output
(GPIO) signals.
AI <3..0> Standard SMA female
connector
Analog input connection.
REF/CLK IN Standard SMA female
connector
Input for an external Reference Clock or
Sample Clock.
The following table lists the available pins on the DIO connector.
Signal Type Direction
MGT Tx± <3..0> 1Xilinx UltraScale GTH Output
MGT Rx± <3..0>1Xilinx UltraScale GTH Input
DIO <7..0> Single-ended Bidirectional
5.0 V DC Output
GND Ground —
Notice The maximum input signal levels are valid only when the module is
powered on. To avoid permanent damage to the PXIe-5763, do not apply a signal to
the device when the module is powered down.
Notice Connections that exceed any of the maximum ratings of any connector on
the PXIe-5763 can damage the device and the chassis. NI is not liable for any
damage resulting from such connections.
Configuring the PXIe-5763 in MAX
Use Measurement & Automation Explorer (MAX) to configure your NI hardware. MAX
informs other programs about which NI hardware products are in the system and how they are
configured. MAX is automatically installed with FlexRIO Support.
1. Launch MAX.
2. In the configuration tree, expand Devices and Interfaces to see the list of installed NI
hardware.
Installed modules appear under the name of their associated chassis.
1MGTs are available only on devices with KU040 and KU060 FPGAs.
8| ni.com | PXIe-5763 Getting Started Guide

3. Expand your Chassis tree item.
MAX lists all modules installed in the chassis. Your default names may vary.
Note If you do not see your module listed, press <F5> to refresh the list of
installed modules. If the module is still not listed, power off the system, ensure
the module is correctly installed, and restart.
4. Record the identifier MAX assigns to the hardware. Use this identifier when
programming the PXIe-5763.
5. Self-test the hardware by selecting the item in the configuration tree and clicking Self-
Test in the MAX toolbar.
The MAX self-test performs a basic verification of hardware resources.
FlexRIO Examples
FlexRIO includes several example applications for LabVIEW. These examples serve as
interactive tools, programming models, and as building blocks in your own applications.
Accessing FlexRIO Examples
FlexRIO examples are available in LabVIEW's NI Example Finder. Complete the following
steps to access the examples by task.
1. In LabVIEW, click Help»Find Examples.
2. In the NI Example Finder window that appears, click Hardware Input and Output»
FlexRIO.
The examples are sorted by task. Click on an example and refer to the Information
window for a description of the example. Refer the Requirements window for a list of
hardware devices that can run the example.
You can also click the Search tab to search all installed examples by keyword. For
example, search for FlexRIO to locate all FlexRIO examples.
Examples also are available online that demonstrate FlexRIO basics, such as using DRAM,
acquiring data from adapter modules, and performing high throughput streaming. Refer to
ni.com/examples for these examples and for more information.
Block Diagram
The following figure shows a block diagram of the carrier portion of the PXIe-5763 (KU035
FPGA version).
PXIe-5763 Getting Started Guide | © National Instruments | 9

Figure 4. Carrier Block Diagram (KU035)
DIO Connector
(Front Panel)
Adapter Module
Connector
+5 V
+1.8 V
+12 V
GPIO
Configuration, GPIO
MGTs
Reference Clock
Power Supplies
Flash
FPGA
PXIe Connectors
PXI Triggers
Clk 100
DStarB, DStarC
Gen3 x8 PCIe
+12 V, +3.3 V
+12 V
Clk 10
Module Clocking
Synchronization
The following figure shows a block diagram of the carrier portion of the PXIe-5763 (KU040
and KU060 FPGA versions).
Figure 5. Carrier Block Diagram (KU040 and KU060)
DIO Connector
(Front Panel)
Adapter Module
Connector
+5 V
+1.8 V
+12 V
GPIO
Configuration, GPIO
MGTs
Reference Clock
Power Supplies
Flash
FPGA
PXIe Connectors
PXI Triggers
Clk 100
DStarB, DStarC
Gen3 x8 PCIe
+12 V, +3.3 V
+12 V
Clk 10
Module Clocking
Synchronization
MGTs
DRAM Bank 0
(2 GB)
DRAM Bank 1
(2 GB)
The following figure shows a block diagram of the I/O portion of the PXIe-5763.
10 | ni.com | PXIe-5763 Getting Started Guide

Figure 6. I/O Block Diagram
EXTERNAL REF/SCLK
CLK IN SMA
CH2 SMA
ADS54J69
Dual 16-bit, 500 MS/s
CH3 SMA
CH1 SMA
ADS54J69
Dual 16-bit, 500 MS/s
CH0 SMA
ANALOG INPUT
DC Coupled
Path
400 MHz
AA Filter
AC (Balun)
Coupled Path
DC Coupled
Path
400 MHz
AA Filter
AC (Balun)
Coupled Path
DC Coupled
Path
400 MHz
AA Filter
AC (Balun)
Coupled Path
DC Coupled
Path
400 MHz
AA Filter
AC (Balun)
Coupled Path
CLOCKING
Adapter Module
Connector
Note Only one analog input path type is populated. Refer to ni.com and the device
specifications for more details.
Component-Level Intellectual Property (CLIP)
The LabVIEW FPGA Module includes component-level intellectual property (CLIP) for HDL
IP integration. FlexRIO devices support two types of CLIP: user-defined and socketed.
•User-defined CLIP allows you to insert HDL IP into an FPGA target, enabling VHDL
code to communicate directly with an FPGA VI.
•Socketed CLIP provides the same IP integration of the user-defined CLIP, but it also
allows the CLIP to communicate directly with circuitry external to the FPGA. Adapter
module socketed CLIP allows your IP to communicate directly with both the FPGA VI
and the external adapter module connector interface.
The PXIe-5763 ships with socketed CLIP items that add module I/O to the LabVIEW project.
PXIe-5763 Getting Started Guide | © National Instruments | 11

PXIe-5763 CLIP
The PXIe-5763 CLIP provides access to four AC- or DC-coupled analog input channels.
In the LabVIEW FPGA Module, 16-bit analog input data is accessed using an I16 data type.
The DIO signals are grouped into two ports of four signals each and are accessed using a U8
data type and a Boolean write enable signal. The four PFI signals are accessed individually
using Boolean signals.
Making a Measurement
Making a Measurement with LabVIEW
1. Launch LabVIEW.
2. Select Help»Find Example.
3. Open the example VI that you want to use by selecting Hardware Input and Output»
FlexRIO.
4. Follow any setup, configuration, and execution instructions in the VI.
Troubleshooting
If an issue persists after you complete a troubleshooting procedure, contact NI technical
support or visit ni.com/support.
What Should I Do if the PXIe-5763 Doesn't Appear in
MAX?
1. In the MAX configuration tree, expand Devices and Interfaces.
2. Expand the Chassis tree to see the list of installed hardware, and press <F5> to refresh
the list.
3. If the module is still not listed, power off the system, ensure that all hardware is correctly
installed, and restart the system.
4. Navigate to the Device Manager.
Operating System Description
Windows 10/8.1 Right-click the Start button, and select Device Manager.
Windows 7 Select Start»Control Panel»Device Manager.
5. Verify the PXIe-5763 appears in the Device Manager.
a) Under an NI entry, confirm that a PXIe-5763 entry appears.
Note If you are using a PC with a device for PXI remote control system,
under System Devices, also confirm that no error conditions appear for the
PCI-to-PCI Bridge.
12 | ni.com | PXIe-5763 Getting Started Guide

b) If error conditions appear, reinstall FlexRIO Support and the PXIe-5763.
What Should I Do if the PXIe-5763 Fails the Self-Test?
1. Restart the system.
2. Launch MAX, and perform the self-test again.
3. Power off the chassis.
4. Reinstall the failed module in a different slot.
5. Power on the chassis.
6. Perform the self-test again.
Where to Go Next
Refer to the following figure for information about other product tasks and associated
resources for those tasks.
custom applications within
an application programming
interface (API).
about hardware features
or review device specifications.
more about your products through ni.com.
the application development
environment (ADE)
for your application.
*This item is also installed with the driver software.
Support
ni.com/support
Located at ni.com/manuals
FlexRIO
ni.com/flexrio
Services
ni.com/services
Located in LabVIEW Example Finder
PXIe-5763
Specifications,
FlexRIO Help*
Getting Started
with LabVIEW
LabVIEW FPGA
Module Help
FlexRIO Module
Examples*
NIPXIe-7911
Worldwide Support and Services
The NI website is your complete resource for technical support. At ni.com/support, you have
access to everything from troubleshooting and application development self-help resources to
email and phone assistance from NI Application Engineers.
PXIe-5763 Getting Started Guide | © National Instruments | 13

Visit ni.com/services for NI Factory Installation Services, repairs, extended warranty, and
other services.
Visit ni.com/register to register your NI product. Product registration facilitates technical
support and ensures that you receive important information updates from NI.
A Declaration of Conformity (DoC) is our claim of compliance with the Council of the
European Communities using the manufacturer’s declaration of conformity. This system
affords the user protection for electromagnetic compatibility (EMC) and product safety. You
can obtain the DoC for your product by visiting ni.com/certification. If your product supports
calibration, you can obtain the calibration certificate for your product at ni.com/calibration.
NI corporate headquarters is located at 11500 North Mopac Expressway, Austin, Texas,
78759-3504. NI also has offices located around the world. For telephone support in the United
States, create your service request at ni.com/support or dial 1 866 ASK MYNI (275 6964). For
telephone support outside the United States, visit the Worldwide Offices section of ni.com/
niglobal to access the branch office websites, which provide up-to-date contact information,
support phone numbers, email addresses, and current events.
Information is subject to change without notice. Refer to the NI Trademarks and Logo Guidelines at ni.com/trademarks for
information on NI trademarks. Other product and company names mentioned herein are trademarks or trade names of their
respective companies. For patents covering NI products/technology, refer to the appropriate location: Help»Patents in your
software, the patents.txt file on your media, or the National Instruments Patent Notice at ni.com/patents. You can find
information about end-user license agreements (EULAs) and third-party legal notices in the readme file for your NI product. Refer
to the Export Compliance Information at ni.com/legal/export-compliance for the NI global trade compliance policy and how
to obtain relevant HTS codes, ECCNs, and other import/export data. NI MAKES NO EXPRESS OR IMPLIED WARRANTIES AS
TO THE ACCURACY OF THE INFORMATION CONTAINED HEREIN AND SHALL NOT BE LIABLE FOR ANY ERRORS. U.S.
Government Customers: The data contained in this manual was developed at private expense and is subject to the applicable
limited rights and restricted data rights as set forth in FAR 52.227-14, DFAR 252.227-7014, and DFAR 252.227-7015.
© 2018 National Instruments. All rights reserved.
376458B-01 July 11, 2018