National Instruments TPC-2230 User manual

USER MANUAL
TPC-2230
Touch Panel Computer (6.5 in./12.1 in./15 in.)
Contents
Electromagnetic Compatibility Guidelines .............................................................................. 2
Conventions .............................................................................................................................. 3
General Information ................................................................................................................. 3
Introduction ...................................................................................................................... 3
I/O Ports............................................................................................................................ 3
System Setup ............................................................................................................................ 4
Important Safety Information ........................................................................................... 4
Setup ................................................................................................................................. 5
Panel Mounting................................................................................................................. 6
Jumpers and Connectors........................................................................................................... 7
Jumper and Connector Functions ..................................................................................... 7
Jumper and Connector Locations ..................................................................................... 8
CMOS Clear Jumper (CN1) ............................................................................................. 10
Specifications............................................................................................................................ 10
Physical............................................................................................................................. 10
Serial Port Settings ................................................................................................................... 18
COM1 Connector Pinout .................................................................................................. 18
COM2 Connector Pinout .................................................................................................. 19
Features in Windows Embedded Standard 7............................................................................ 21
EWF and FBWF ............................................................................................................... 21
HORM .............................................................................................................................. 21
Drivers .............................................................................................................................. 21
Touchscreen Configuration ...................................................................................................... 22
Worldwide Support and Services ............................................................................................. 22

2|ni.com |TPC-2230 User Manual
Electromagnetic Compatibility Guidelines
This hardware has been tested and found to comply with the applicable regulatory requirements
and limits for electromagnetic compatibility (EMC) as indicated in the hardware’s Declaration
of Conformity (DoC)1. These requirements and limits are designed to provide reasonable
protection against harmful interference when the hardware is operated in the intended
electromagnetic environment. In special cases, for example when either highly sensitive or noisy
hardware is being used in close proximity, additional mitigation measures may have to be
employed to minimize the potential for electromagnetic interference.
While this hardware is compliant with the applicable regulatory EMC requirements, there is no
guarantee that interference will not occur in a particular installation. To minimize the potential
for the hardware to cause interference to radio and television reception or to experience
unacceptable performance degradation, install and use this hardware in strict accordance with
the instructions in the hardware documentation and the DoC1.
If this hardware does cause interference with licensed radio communications services or other
nearby electronics, which can be determined by turning the hardware off and on, you are
encouraged to try to correct the interference by one or more of the following measures:
• Reorient the antenna of the receiver (the device suffering interference).
• Relocate the transmitter (the device generating interference) with respect to the receiver.
• Plug the transmitter into a different outlet so that the transmitter and the receiver are on
different branch circuits.
Some hardware may require the use of a metal, shielded enclosure (windowless version) to meet
the EMC requirements for special EMC environments such as, for marine use or in heavy
industrial areas. Refer to the hardware’s user documentation and the DoC1for product
installation requirements.
When the hardware is connected to a test object or to test leads, the system may become more
sensitive to disturbances or may cause interference in the local electromagnetic environment.
Operation of this hardware in a residential area is likely to cause harmful interference. Users are
required to correct the interference at their own expense or cease operation of the hardware.
Changes or modifications not expressly approved by National Instruments could void the user’s
right to operate the hardware under the local regulatory rules.
Notice To ensure the specified EMC performance, operate this product with only
shielded cables and accessories connected to USB and COM ports.
Notice To ensure the specified EMC performance, the length of cables connected
to USB and COM ports must be no longer that 3 m (10 ft.).
1 The Declaration of Conformity (DoC) contains important EMC compliance information and instructions
for the user or installer. To obtain the DoC for this product, visit ni.com/certification, search by
model number or product line, and click the appropriate link in the Certification column.

TPC-2230 User Manual |© National Instruments |3
Conventions
This symbol denotes a caution, which advises you of precautions to
take to avoid injury. When this symbol is marked on a product, refer to
the Important Safety Information section for information about
precautions to take.
When this symbol is marked on a product, it denotes a warning
advising you to take precautions to avoid electrical shock.
When this symbol is marked on a product, it denotes a component that
may be hot. Touching this component may result in bodily injury.
Take precautions to avoid data loss, loss of signal integrity, degradation
of performance, or damage to the model.
General Information
This section includes general information about the TPC-2230 Human Machine Interface (HMI).
Introduction
The TPC-2230 touch panel computer, an HMI based on an x86 platform, includes these key
features:
•Powerful processing—The TPC-2230 uses the Intel Atom processor, specifically
designed for embedded, industrial applications.
•Fanless—By using an advanced but low-power Intel Atom processor, the TPC-2230 does
not require a fan for cooling.
•Robust communication—The TPC-2230 is a powerful I/O interface for easy
communication with other devices. The I/O interface includes serial ports, gigabit Ethernet,
and support for USB 2.0 and USB 3.0.
•Wide operating temperature—The TPC-2230 provides a -20 °C to 60 °C operating
temperature range.
•Windows Embedded support—The TPC-2230 supports Windows Embedded Standard 7
(WES7).
I/O Ports
The TPC-2230 includes the following ports:
• Two serial ports: RS232 (COM1) and RS232/422/485 (COM2)
• One USB 2.0 port compliant with USB 1.0 and 1.1
• One USB 3.0 port compliant with USB 2.0, 1.0 and 1.1
• Two RJ-45 Gigabit Ethernet ports
• One power connector

4|ni.com |TPC-2230 User Manual
Figure 1 shows the I/O port arrangement.
Figure 1. I/O Port Arrangement
For more TPC-2230 specifications, refer to the Specifications section.
System Setup
This section includes setup information for the TPC-2230.
Important Safety Information
Before setting up the TPC-2230, read these safety instructions carefully.
Disconnect this equipment from any AC outlet before cleaning. Use a damp cloth. Do not use
liquid or spray detergents for cleaning.
For plug-in equipment, the power outlet socket must be located near the equipment and must be
easily accessible.
Keep this equipment away from excessive humidity.
Place this equipment on a reliable surface during installation. Dropping it or letting it fall may
cause damage.
The openings on the enclosure are for air convection and protect the equipment from
overheating. Do not cover the openings.
Make sure the power source voltage is correct before connecting the equipment to the power
outlet.
Position the power cord so that it cannot be stepped on. Do not place anything over the power
cord.
All cautions and warnings on the equipment should be noted.
If the equipment is not used for a long time, disconnect it from the power source to avoid damage
by transient overvoltage.
1 Power Connector
2LANB
3LANA
4 USB 2.0 (Bottom) and USB 3.0 (Top)
5 COM2 (RS232/422/485)
6 COM1 (RS232)
23456
1

TPC-2230 User Manual |© National Instruments |5
Never pour any liquid into an opening. This may cause fire or electrical shock.
Never open the equipment. For safety reasons, only qualified service personnel should open the
equipment.
If one of the following situations arises, have service personnel check the equipment:
• The power cord or plug is damaged.
• Liquid has penetrated into the equipment.
• The equipment has been exposed to moisture.
• The equipment does not work well, or you cannot get it to work according to the user manual.
• The equipment has been dropped and damaged.
• The equipment has obvious signs of breakage.
Do not leave this equipment in an environment where the storage temperature may go below
-30 °C (-22 °F) or above 80 °C (176 °F). Doing so could damage the equipment. The equipment
should be in a controlled environment.
Caution There is a danger of explosion if the battery is incorrectly replaced.
Replace the battery only with the same or equivalent type recommended by the
manufacturer. Discard used batteries according to the manufacturer’s instructions.
The sound pressure level at the operator’s position according to IEC 704-1:1982 is no more than
70 dB (A).
Caution The protection this equipment provides may be impaired if it is used in a
manner not described in this manual.
Setup
Follow these steps to set up the TPC-2230:
1. Unpack the TPC-2230. Be sure your kit includes the following items:
• The TPC-2230 HMI
• Ten panel mounting clamps
• Ten panel mounting screws (M4x30)
• Six panel mounting screws for limited space mounting (M4x20)
• Six GRANO panel mounting screws for limited space mounting (M4x16)
• One 3-pin power connector
• One HMI Resource Recovery USB
• One earth ground cable
• Two screws for optional mPCIe module
If any items are missing or damaged, contact National Instruments.
Caution Be sure system power is off before plugging in or pulling out the CFast
card.

6|ni.com |TPC-2230 User Manual
2. Verify that the CFast card containing Windows Embedded or another operating system is
installed in the unit.
3. Connect the power connector to an 24 VDC power line. Be sure to connect the positive,
negative, and ground lines as shown in Figure 2. The power lines can be from either a
power adapter or in-house power source. Connect GND_EARTH to chassis GND.
Figure 2. Power Connector
4. Connect the power connector to the power receptacle on the TPC-2230. The power
receptacle pin assignment is shown in Figure 3. Note the position of the earth ground pin,
marked G.
Figure 3. Power Receptacle and Pin Assignment
5. The system turns on immediately after you apply power.
Touchscreen Calibration
The TPC-2230 touchscreen should be correctly calibrated and ready to use when you power on
the system. However, if the calibration is not correct or you want to choose custom calibration
options, refer to the Touchscreen Configuration section.
Panel Mounting
Follow these steps to mount the TPC-2230 in a panel:
1. Install the TPC-2230 in the panel opening. (Refer to the Specifications section for cutout
dimensions.)
2. Hook the clamps included in the accessory pack to the holes around the four sides of the
bezel. Be sure to remove the protective inserts in the panel mounting holes.
3. Insert the screws included in the accessory pack into the clamps. To fasten the TPC-2230
to the panel, tighten the screws so they push against the mounting panel.
• Use ten clamps and M4x30 screws to panel mount the 15 in. unit.
• Use eight clamps and M4x30 screws to panel mount the 12 in. unit.
• Use six clamps and M4x20 screws to panel mount the 6.5 in. unit.
+–GND_EARTH
G–+

TPC-2230 User Manual |© National Instruments |7
Note Use GRANO screws if the CFast slot is blocked by one of the longer screws.
Note The mounting panel thickness should be less than 6 mm (0.236 in.).
Jumpers and Connectors
This section describes the TPC-2230 jumpers and connectors.
Jumper and Connector Functions
Table 1-4 lists the jumper and connector functions.
Table 1-4. Mainboard Connectors and Jumpers
Label Function Description
BH2 Battery RTC battery bracket
CN1 CMOS CMOS clear select
CN7/CN8 LAN RJ45 connection
CN10 USB connector USB data and power
CN12 SATA connector SATA data connection
CN13 SATA power SATA device power
CN14 CFast slot CFast power and data
CN15 COM1 Serial port: COM1 RS232
CN16 COM2 Serial port: COM2 RS232/422/485
CN18 Power in connector Device power input
MINIPCIE Mini PCIe Connection for Mini PCIe device
SW2 COM2 mode Select COM2 RS232/422/485
SW3 Termination Termination resistor select

8|ni.com |TPC-2230 User Manual
Jumper and Connector Locations
Figures 5 and 6 show the jumper and connector locations.
Figure 5. Main Board Jumpers and Connectors—Top Side
CN15
CN16
CN10
CN7
CN8
PFS1
MINIPCIE1
CN18
SW4
CN1
U36
BH2
SODIMM1
SW3
SW2
SW1
CN12
CN13
CN6
CN5
CN11
CN4
CN3
CN2
CN9
CN17
BH1
U1
CN20

TPC-2230 User Manual |© National Instruments |9
Figure 6. Main Board Jumpers and Connectors—Bottom Side
U26
U6
U10
U48
U12
CN19
CN14
JDEDEBUG1

10 |ni.com |TPC-2230 User Manual
CMOS Clear Jumper (CN1)
The CMOS Clear jumper is disabled by default. To enable CMOS Clear, move the jumper from
the 1-2 position to the 2-3 position. Pin 1 is the pin on CN1 closest to the front panel connectors.
Specifications
This section lists the TPC-2230 system specifications.
Physical
6.5 in.
Weight 1.5 kg (52.91 oz)
Dimensions (W × H × D) 199 mm × 152 mm × 58.9 mm
(7.83 in. × 5.98 in. × 2.32 in.)
Cutout dimensions (suggested) 189.1 mm× 142.1 mm
(7.44 in. × 5.59 in.)
12.1 in.
Weight 2.5 kg (88.18 oz)
Dimensions (W × H × D) 311.8 mm × 238 mm× 57.2 mm
(12.28 in. × 9.37 in. × 2.25 in.)
Cutout dimensions (suggested) 303 mm× 229 mm
(11.93 in. × 9.02 in.)
Table 1-7. CN1 Jumper Functions
Position Function
1-2 Disabled
2-3 Clear CMOS
31
31

TPC-2230 User Manual |© National Instruments |11
15 in.
Weight 3.9 kg (137.57 oz)
Dimensions (W × H × D) 383.2 mm × 307.3 mm × 61.1 mm
(15.09 in. × 12.10 in. × 2.41 in.)
Cutout dimensions (suggested) 374.5 mm × 298.5 mm
(14.74 in. × 11.75 in.)
Figure 8. Dimensions of 6.5 in. Device
7.00 mm
(0.28in.)
101.10 mm
(3.98in.)
134.20 mm
(5.28in.)
152.00 mm
(5.98in.)
199.00 mm
(7.83 in.)
132.00 mm
(5.2 in.)
7.00 mm
(0.28in.)
7.00 mm
(0.28in.)
58.90 mm
(2.32 in.)
187.80 mm
(7.39 in.)
140.80 mm
(5.54 in.)

12 |ni.com |TPC-2230 User Manual
Figure 9. Dimensions of 12.1 in. Device
4.00 mm
(0.0 in.)
7.00 mm
(0.28in.)
180.00 mm
(7.08in.)
311.80 mm
(12.28in.)
247.20 mm
(9.73in.)
186.30 mm
(7.33 in.)
238.00 mm
(9.37 in.)
150.00 mm
(5.90 in.)
7.00 mm
(0.28in.)
7.0 mm
(0.28in.)
57.20 mm
(2.25 in.)
301.60 mm
(11.87 in.)
227.60 mm
(8.96 in.)

TPC-2230 User Manual |© National Instruments |13
Figure 10. Dimensions of 15 in. Device
System
CPU Intel Atom Processor E3827 1.75 GHz
Video Integrated
BIOS AMI UEFI BIOS
LAN 10/100/1000 Base-T 2 ports
7.00 mm
(0.28in.)
115.00 mm
(4.53in.)
383.20 mm
(15.08in.)
306.10 mm
(12.05 in.)
230.10 mm
(9.06 in.)
307.30 mm
(12.09 in.)
372.90 mm
(14.68in.)
296.90 mm
(11.68in.)
115.00 mm
(4.53in.)
180.00 mm
(7.08mm)
7.00 mm
(0.28in.)
7.0 mm
(0.28in.)
61.10 mm
(2.40 in.)
4.00 mm
(0.0 in.)

14 |ni.com |TPC-2230 User Manual
RAM 4 GB DDR3L 1600MHz SO-DIMM
Watchdog timer 1 to 255 s timeout period
Storage CFast, 1 slot
LCD
Display type TFT LED LCD
Maximum resolution
6.5 in. 640 × 480 XGA
12.1 in. 1024 × 768 XGA
15 in. 1024 × 768 XGA
Maximum colors
6.5 in. 262,000
12.1 in. 262 k/16.2 M
15 in. 262 k/16.2 M
Viewing angle 160°/140°
Luminance (cd/m2)
6.5 in. 800
12.1 in. 600
15 in. 400
Contrast ratio
6.5 in. 600:1
12.1 in. 700:1
15 in. 700:1
Backlight LED
Backlight lifespan 50,000 hr
Note There may be several bright or dark pixels on the LCD. This phenomenon is
normal in LCD manufacturing.

TPC-2230 User Manual |© National Instruments |15
Touchscreen
Touch type Resistive 5-wire
Base glass construction Tempered glass
Resolution
6.5 in. 640 × 480
12.1 in. 1024 × 1024
15 in. 1024 × 1024
Light transmission 80% ± 3%
Controller USB interface
Lifespan 1 million touches at a single point
Power
Input voltage 24 VDC ± 20%
Power consumption (typical)
6.5 in. 19.2 W
12.1 in. 45.6 W
15 in. 40.8 W
Note Providing power levels either below or above the stated range is not
recommended.
Environment
Operating temperature -20 °C to 60 °C (-4 °F to 140 °F)
Storage temperature -30 °C to 70 °C (-22 °F to 158 °F)
Humidity 40 °C @ 10% to 95% relative humidity
(noncondensing)
Vibration 2 grms (5 Hzto 500 Hz)
Maximum altitude 2,000 m
Pollution Degree 2
Indoor use only
Note The front bezel is compliant with IP66.

16 |ni.com |TPC-2230 User Manual
Safety
This product is designed to meet the requirements of the following standards of safety for
information technology equipment:
• IEC 60950-1, EN 60950-1
• UL 60950-1, CSA 60950-1
Note For UL and other safety certifications, refer to the product label or the Online
Product Certification section.
Electromagnetic Compatibility
This product meets the requirements of the following EMC standards for information
technology equipment:
• EN 55024 (CISPR 24); Immunity
• EN 55022 (CISPR 22); Class A Emissions
• AS/NZS CISPR 22; Class A Emissions
• FCC 47 CFR Part 15B: Class A Emissions
• ICES-003: Class A Emissions
Note For the standards applied to assess the EMC of this product, refer to the
Online Product Certification section.
CE Compliance
This product meets the essential requirements of applicable European Directives as follows:
• 2014/35/EU; Low-Voltage Directive (safety)
• 2014/30/EU; Electromagnetic Compatibility Directive (EMC)
Online Product Certification
Refer to the product Declaration of Conformity (DoC) for additional regulatory compliance
information. To obtain product certifications and the DoC for this product, visit ni.com/
certification, search by model number or product line, and click the appropriate link in the
Certification column.
Environmental Management
NI is committed to designing and manufacturing products in an environmentally responsible
manner. NI recognizes that eliminating certain hazardous substances from our products is
beneficial to the environment and to NI customers.
For additional environmental information, refer to the Minimize Our Environmental Impact web
page at ni.com/environment. This page contains the environmental regulations and
directives with which NI complies, as well as other environmental information not included in
this document.

TPC-2230 User Manual |© National Instruments |17
Waste Electrical and Electronic Equipment (WEEE)
EU Customers At the end of the product life cycle, all products must be sent to
a WEEE recycling center. For more information about WEEE recycling centers,
National Instruments WEEE initiatives, and compliance with WEEE Directive
2002/96/EC on Waste and Electronic Equipment, visit ni.com/environment/
weee.
Battery Replacement and Disposal
EU Customers This device contains a long-life coin cell battery. If you need to
replace it, use the Return Material Authorization (RMA) process or contact an
authorized National Instruments service representative. For more information about
compliance with the EU Battery Directive 2006/66/EC about Batteries and
Accumulators and Waste Batteries and Accumulators, visit ni.com/
environment/batterydirective.
Mercury Disposal and Recycling
LCD lamp(s) in this monitor contain mercury. Dispose or recycle according to local, state or
federal laws. Consult the Electronic Industries Alliance at www.eiae.org for more
information. For specific information on lamp disposal, consult www.lamprecycle.org.
Cleaning
If you need to clean the unit, use a damp cloth. Do not use liquid or spray detergents for cleaning.
Make sure that the unit is completely dry and free from contaminants before returning it to
service.
Cd/Hg/Pb
⬉ᄤֵᙃѻક∵ᶧ᥻ࠊㅵ⧚ࡲ⊩ ˄Ё೑ RoHS˅
Ё೑ᅶ᠋ National Instruments ヺড়Ё೑⬉ᄤֵᙃѻકЁ䰤ࠊՓ⫼ᶤѯ᳝ᆇ⠽䋼ᣛҸ
(RoHS)DŽ݇Ѣ National Instruments Ё೑ RoHS ড়㾘ᗻֵᙃˈ䇋ⱏᔩ ni.com/
environment/rohs_chinaDŽ(For information about China RoHS compliance,
go to ni.com/environment/rohs_china.)

18 |ni.com |TPC-2230 User Manual
Serial Port Settings
This section describes the TPC-2230 serial port settings.
COM1 Connector Pinout
The TPC-2230 COM1 serial port is RS232 only. The following figure and table show the COM1
connector pinout.
Pin Signal
1DCD
2RX
3TX
4DTR
5GND
6DSR
7RTS
8CTS
9RI
15
9
6

TPC-2230 User Manual |© National Instruments |19
COM2 Connector Pinout
The TPC-2230 COM2 serial port is adjustable. You can set it to RS-232, RS-422, or RS-485,
and it has auto data flow control capability. In other words, the TPC-2230 can automatically
detect the data flow direction at this port when two-wired RS485 communication is activated.
The following figure and table show the COM2 pinout and settings.
PIN RS-232 RS-422 RS-485
1DCD TX- D-
2RX TX+ D+
3TX RX+ —
4DTR RX- —
5GND GND GND
6DSR — —
7RTS — —
8CTS — —
9RI — —
15
9
6

20 |ni.com |TPC-2230 User Manual
COM4 Mode SW2 Setting
RS232 Mode
RS422 Master Mode
RS422 Slave Mode
RS485 Mode
20 11
101
20 11
101
20 11
101
20 11
101