National Specialty Lighting LED Brick Star Gen I User manual

1. First remove fixture cover by unscrewing two bolts
holding cover to can.
2. Remove LED Brick Star reflector by unscrewing the
screws, holding reflector in place. See schematic on
adjacent page.
3. Using a knife, or very thin flat blade screwdriver,
remove reflector and set beside fixture.
4. Select a mounting location for the LED Brick Star.
Fixture should be within reach of 120VAC power,
located 9 inches above the surface to be lit, and situ-
ated at the best location along the mounting surface
for the illumination task.
5. LED Brick Star may be used in any standard brick wall
in lieu of a brick. Make sure LED Brick Star is com-
pletely wired and inspected before wall is completed.
NOTE: Masonry wall installation warning adjacent
schematic, and corrosion warning on reverse side.
6. LED Brick Star has flanges that will allow the can
to be securely affixed to almost any surface with
the four mounting screws provided. Installations in
drywall will require a wood backing behind drywall.
Place can in hole (7-3/4” x 3-1/4” x 2-1/2”) and mark
the position of the four mounting screws. Reposi-
tion can in hole, and securely fasten the can to the
mounting surface by firmly tightening four mounting
screws.
In the highly unlikely event of an LED module failure,
please follow the instructions listed below:
CAUTION! If unit has recently been operating, glass
lens and LED module are hot! Turn off fixture and allow
it to cool for 15 minutes before relamping.
CAUTION! Always turn off the main power, before
replacing the LED module.
NOTE: Using a thin pair of gloves during this proce-
dure will eliminate fingerprints on glass lens and LED
module.
1. First remove fixture cover by unscrewing two bolts
holding cover to can.
2. Remove the reflector by unscrewing the screws
holding it in place.
3. Disconnect the LED module from 120V wires. Please
make sure that the 120V wires are not “hot”.
4. Remove the LED module by unscrewing the screws
holding it in place. Replace it with a new one. Tighten
screws just snug.
5. Re-connect the power wires to the LED module.
6. Replace the reflector by tightening the screws.
7. Replace fixture cover by fitting cover to can so gasket
seals and screwing in both cover bolts firmly.
WARNING! If this fixture is to be placed in a masonry
or brick wall, you must use a Concrete Cap during can
installation to provide the proper void for the fixture
cover. Failure to use the Concrete Cap will almost
guarantee concrete or grout forming against fixture can
flange, and poor cover-to-can seal (see below). Poor
cover seal will allow water/moisture into fixture result-
ing in LED failure.
CAUTION! Use RTV silicone and water-tight fittings on
all wet locations connections to fixture.
1. Through one of the three NPT fittings provided, bring
in 120VAC power wiring. If 120VAC wire will not con-
veniently enter one of the three NPT fittings provided,
simply unscrew the can, rotate can 180 degrees, and
reinstall. Can is entirely symmetrical, and 180 degree
rotation will not affect mounting holes.
2. Secure wire to fixture with the appropriate strain
relief (not provided).
3. Strip 1/3” (8mm) of the insulation off each incom-
ing 120VAC power wire. Connect white incoming
120VAC wire (neutral wire) to push-in connector on
white wire from LED module. Connect black wire
from LED module. Connect ground wire to push-in
connector on green wire screwed into can. Push all
wires firmly down into connectors, so that uninsu-
lated wire is not exposed.
4. Reinstall assembly, reflector, and cover.

Push-in
Connector
Incoming
120VAC Outgoing
120VAC
120VAC
Push-in
Connector
LED Module
INSTALLATION
INSTRUCTIONS
LED
Brick Star
GEn ii
120 VDC LED technology
in a brick-size die cast
aluminum xture
Ultra low 5.2 watts per fixture
Dimmable
Louver, Scoop & Prism cover designs
White, Bronze, Black and Aluminum colors
Stainless Steel Louver Option
Suitable for:
Wet Locations, Insulation Contact
Wall and Ceiling Mount, Showers
Use in Poured Concrete
The LED Brick Star could be dimmed using dimmers
with forward phase TRIAC design.
Recommended manufacturer and model numbers are
listed below:
LUTRON SCL-153PH
LUTRON CTCL-153P
LEVITON 6674
LEVITON IPL06