Naturally Filtered Kitchen User manual

2
Kitchen Cutaway
Congratulations on your purchase of the Natural Kitchen system. The
Natural Kitchen combines the best available filtration technologies to give you
pure, naturally filtered water straight from the tap for pennies per gallon. Carbon
block is tested to NSF Standards for reduction of chlorine, chloramines, THMs,
VOCs, MTBE, PCBs, pesticides, lead, mercury, and others (see performance
data sheet for full list). Proven nano fiber technology virtually eliminates Bacteria
and Viruses. Filtered water retains the healthy, naturally occurring minerals that
stabilize water and provide its unique flavor.
Please review and keep this guide for reference as it will assist you with trouble-
shooting your unit in the future if necessary.
1
Specifications
Filtration Media 0.5 Micron Carbon Block
0.02 Micron Nano Fiber Wrap
Flow Rate 1 - 1.5 gpm (3.8 - 5.68 lpm)
Pressure Range 20 - 100 psi (1.38 bar - 6.89 bar)
Rated Cartridge Life 1,200 gallons (4,542 liters) or 1 Year
Operating Temperature 40o– 100oF (5o– 38oC) Warning: Do not allow expo-
sure to freezing temperatures
System Dimensions 8.25 x 6.5 Inches (21 x 16.5 cm)
Cartridge Dimensions 7.25 x 4.5 Inches (18.4 x 11.4 cm)
Connections Inlet/Outlet 1/8“ FNPT x 1/4” Compression
Weight 9 lbs. (4 kg)
Construction 304 Stainless Steel Housing, Base, Band Clamp
Brass Attachment Fittings
Congratulations
Stainless Housing
Housing built out of 304L
Stainless Steel which is
stronger and more durable
than plastic materials.
Nano Fiber Wrap
Multiple layers of nano
fiber provide 0.02 um
nominal reduction,
reducing 99.99% Virus
and 99.9999% Bacteria.
Carbon Block
Large blended carbon
block provides 0.5 um
absolute reduction
to reduce cysts. Also
reduces chemicals
such as chlorine
and chloramines,
trihalomethanes (THMs),
volatile organics (VOCs),
MTBE, PCBs, pesticides,
lead, mercury, dirt, rust,
sediment, foreign odors,
taste, and others.
Band Clamp
Connects the housing
to the base, making
cartridge change quick
and easy. No tools
required.
Tested to NSF Standards 42 and 53 for chemical reduction
Reduces Bacteria by 99.9999% and Virus by 99.99%
Filters 2 - 3 times faster than most systems (up to 1.5 GPM)
Single cartridge filters up to 1200 gallons for one year
Made in the USA from high grade stainless steel
Streamlined design reduces potential for leaks and failures
Lifetime Warranty on all stainless steel components

3
System Attachments
4
Install - Above Sink
The Natural Kitchen comes with a diverter valve designed to fit the majority of
standard male and female faucets with removable aerators.
If you have a designer or commercial faucet, extendable hose or non-standard
spout you may need to replace your faucet or install your Natural Kitchen under
your sink with the Under Sink Adaptor Kit - sold separately.
Step 1. Remove Aerator
Unscrew the faucet aerator
using your hand or a small tool
such as pliers or a wrench.
Optional: Female Faucet
The male adaptor may require
an extra washer to fit some
spouts. Use the washer from
the recently removed aerator
(Step 2) if needed.
Step 6: Check for Leaks
If you spot a leak check to
make sure the rubber washer
is in place. If the faucet
surface is damaged teflon
tape may help achieve a seal.
Teflon Tape
Step 7. Flush your System
Let filtered water run for 3 - 5
minutes. This will eliminate air
in the line and flush carbon
fines from the cartridge.
Your unit is now ready for use.
Step 3. Cleaning
Clean the spout threads. To
remove dirt, use an old tooth-
brush and flush with water.
Step 2. Retain Washer
The aerator & washers may
be needed later. Set these
pieces aside for safe-keeping.
Step 5a. Female Faucet
If your faucet is female, first
attach the male adaptor to
the spout by threading the
fitting on clockwise. A coin
can be used to tighten.
Step 5b: All Faucets
Connect the diverter to the
male faucet or adaptor by
turning the threaded collar
on the top of the diverter
clockwise until it is finger tight.
Step 4. Determine Threads
A female faucet has threads
on the inside. A male faucet
has visible threads on the
outside.
1. 1/4” OD LLDPE Tubing (10’)
2. Inlet/Outlet Fittings
1/4” Compression Nut (2)
1/4” Plastic Sleeve (2)
1/4” Brass Insert (2)
3. Shut-Off Valve
(Attached) 1/4” Compression Nut (1)
(Attached) 1/4” Plastic Sleeve (1)
1/4” Brass Insert (1)
4. T-Valve
5. Optional Fittings
(For Copper Cold-Water Lines)
3/8” Compression Nut (1)
3/8” Brass Sleeve (1)
6. Faucet Mounting Hardware (5)
7. Faucet Fittings
1/4” Compression Nut (1)
1/4” Plastic Sleeve (1)
1/4” Plastic Insert (1)
8. Faucet
1
2
5
4
6
3
7
8
Under Sink Attachments
Above Sink Attachments
1. 1/4” Above Sink Dual Tubing (5’)
2. Diverter Valve
15/16” 27-Thread Female
Attached Rubber Washer
3. Male/Male Adaptor
15/16” x 55/64” 27-Thread Male
Attached Rubber Washer
Optional Male/Male Adaptor
(sold seperately)
13/’16” x 55/64” 27-Thread Male
Attached Rubber Washer
1
2
3
Threaded
Collar
The Natural Kitchen comes with either Above Sink or Under Sink attachments.
If you decide to convert your system later, attachment kits are sold seperately.
Mounting Bracket: Naturally Filtered offers an optional mounting bracket
accessory for Under Sink installations. This bracket attaches your Natural
Kitchen upside down to the cabinet under your sink. The bracket places your
system out of the way. The bracket is also recommendedd if you intend to
hard-plumb with copper lines. Contact Naturally Filtered or your local Dealer for
more details.

5 6
Install - Under Sink
Naturally Filtered recommends you hire a licensed professional plumber for
installations under the sink. Working with plumbing without proper expertise can
lead to significant leaks and water damage to your home. These instructions are
a supplement and not a replacement for professional assistance.
Sample Install
Step 1. Shut off Cold Water
Turn cold water stop valve
clockwise to close. Turn
kitchen faucet to cold water to
verify water is off and relieve
pressure.
Step 3. Shut-Off Valve
Thread Shut-Off Valve onto the
T of the T-Adaptor. Ensure the
Shut-Off Valve is accessible
for tubing installation. In some
cases Shut-Off Valve may need
to be connected to T-Adaptor
prior to connecting to cold
water valve.
Step 2. T-Adaptor
T-Adaptor should be
connected between the
cold water valve and the
plumbing line leading to the
main faucet. Do not attempt
to disconnect tubing under
pressure.
Step 6. Outlet Tubing
Connect tubing to Outlet
Fitting on Base (See
Diagram A).
Step 5. Inlet Tubing
Remove blue caps covering
inlet and outlet fittings.
Connect tubing to Inlet Fitting
on Base (See Diagram A).
Step 4. Shut-Off Valve Tubing
Connect tubing to Shut-Off
Valve (See Diagram A).
Outlet
Inlet
Step 8. Leak Check
Ensure Auxiliary Faucet and
Shut-Off Valve are closed.
Open cold water stop valve
slowly and check for leaks
on Shut-Off Valve and
T-Adaptor. If a leak is found,
close the cold water valve and
diagnose the leak. If there are
no leaks, SLOWLY open the
Shut-Off Valve and check the
system, Auxiliary Faucet, and
all tubing and fittings for leaks.
Step 9. System Flush
Once you have verified that
the installation is free of leaks,
open the Auxiliary Faucet and
let water run for 3 - 5 minutes.
This will help eliminate air in
the line and flush carbon fines
from the cartridge. Close the
Auxiliary Faucet and do a final
leak check.
Your unit is now ready for
use.
Step 7. Auxiliary Faucet
Install Auxiliary Faucet into pre-
cut hole on sink. Reference
Diagrams A and B for proper
tubing installation. If tubing
is inserted too far into faucet
or compression nut is not
tightened tubing may blow off
during pressurization. Pull on
tubing to test seal.
Below
Sink
Above
Sink
Diagram A - Compression Fitting Installation
Slip compression nut and plastic sleeve over tubing. Push brass
insert into tubing completely. Insert tubing into fitting. Connect
compression nut to fitting and thread down tightly to compress
plastic sleeve and create seal.
Brass
Insert
Plastic
Sleeve
Compression
Nut
Diagram B - Auxiliary Faucet Compression Fitting
Do not insert tubing more
than 1/2” into the faucet.

7
Cartridge Change
8
Useage Tips
Step 1. Shut Off Water
Undersink Only. Close the
Shut-Off Valve by turning the
handle clockwise.
Step 6. Install Cartridge
Install new Cartridge by
inserting the double o-ring
nipple on the Cartridge into
the center hole of the Base.
Press the top of the Cartridge
down to secure.
Step 8: Pressurize System
Undersink Only. SLOWLY
open the Shut-Off Valve by
turning the handle counter-
clockwise. Check the system,
Auxiliary Faucet, and all tubing
and fittings for leaks.
Step 9. Flush Cartridge
Let filtered water run for
3 - 5 minutes. This will help
eliminate air in the line and
flush carbon fines from the
cartridge.
Your unit is now ready for use.
Step 3. Remove Band Clamp
Turn Band Clamp Knob
counter-clockwise to loosen.
Once loose, remove and set
aside.
Step 2. Relieve Pressure
Undersink Only. Open the
Auxiliary Faucet until water
stops flowing to relieve
pressure on the system.
Step 5. Replace O-Ring
Remove existing O-Ring from
Base. Whipe away any visible
debris on Base and install the
new O-Ring supplied in your
cartridge pack.
Step 7: Attach Band Clamp
Place the Housing over the
Base and Cartridge. Housing
should rest on the new O-
Ring. Attach the Band Clamp
around the Housing and Base
and secure the latch. Turn the
Knob clockwise until tight.
Step 4. Remove Cartridge
Using your hands or with
gloves, pull Cartridge and
Base out of Housing. Pull
old cartridge off of the Base.
Dispose of old cartridge and
set Base and Housing aside.
Turn
Clockwise
Turn
Counter-
Clockwise
Warning: Failure to shut off your water and relieve pressure
in undersink systems could result in injury and flooding.
Latch
Knob
Tap Water
Lever Down
For tap water, the black lever
on the diverter valve should
be vertical. Your tap can op-
erate normally with hot and
cold water.
Filtered Water
Lever Up
For filtered water, the black
lever on the diverter valve
should be horizontal. Note:
do not put hot water through
the filter.
Initial Flushing
On your first use and each time you change the cartridge you will need to flush your system.
Running your filtered water for 3 - 5 minutes will get rid of any excess carbon fines (black
dust) that may be present. These excess carbon fines are completely harmless and should
not appear after the system has been fully flushed.
After Vacation
When using the filter for the first time after an extended period of non use (such as a vaca-
tion or holiday) to obtain the best possible drinking water quality we recommend running
water through the filter for approximately 30 to 60 seconds.
Cartridge Change
The Natural Kitchen Cartridge is rated for 1200 Gallons or 1 year. The average useage of
water for a family of four is 1,000 gallons per year for cooking and drinking. Even if you use
less water, replace your cartridge every year to ensure optimal performance.
Diverter Cleaning
If your source water is hard, scale can form on your diverter valve. Scale can clog aerator
screens and eventually damage seals and the internal valve mechanism. You can extend
the life of your diverter by periodically cleaning the aerator screens. Both are removeable by
turning the filtered or tap nozzles counter-clockwise.
System Cleaning
The stainless steel components are designed to be used for many years. It is a good idea
to clean the inside of the system during cartridge change every 2 - 3 years. Mild soap and
water is recommended. If you use bleach or hydrogen peroxide rinse the components
thoroughly afterwards.
Optional: Leak Controller
The Natural Kitchen is designed with high quality stainless steel materials and uses brass
compression connections to reduce the potential for leaks as much as possible. While this
unit is engineered to the highest standards, a risk of an unanticipated failure which could cause
flooding is always possible. If you are installing the Natural Kitchen in an area where a leak
could cause substantial water damage to your home you should consider purchasing a leak
controller.

9
Other Products
NATURALLY FILTERED, LLC warrants The Natural Kitchen for one (1) year
from the date of purchase against all defects in materials and workmanship
when installed and used in compliance with this Installation Manual. Further,
NATURALLY FILTERED, LLC warrants the stainless steel components (housing,
base, and band clamp) for life, provided that the filter and o-ring have been
replaced at least once per year.
NATURALLY FILTERED, LLC will replace or repair any part which, in
our opinion, is defective, if the filter, furnishings, and fixtures have not been
subjected to tampering, alteration, or improper use or transportation after
delivery and have not been repaired by anyone except NATURALLY FILTERED,
LLC or an authorized representative. NATURALLY FILTERED, LLC’s obligation
does not include any costs related to shipping and transportation. NATURALLY
FILTERED, LLC is not responsible for damage in transit, the customer should
present claims for such damage to the carrier.
NATURALLY FILTERED, LLC makes no warranties, expressed or implied,
including, without limitation, any warranties of fitness or merchantability except
as expressly set forth above. NATURALLY FILTERED, LLC shall not be liable
for any anticipated or lost profits, incidental damages, consequential damages,
costs, time charges, or other losses incurred in connection with the purchase,
installation, repair, or operation of the filter, and we do not authorize anyone to
assume for NATURALLY FILTERED, LLC any liability in connection with the filter
or any part thereof. NATURALLY FILTERED, LLC reserves the right to modify
the design of our products at any time without notice.
This warranty covers the filter for residential use only and, in addition, does NOT
apply to:
1. Failures resulting from use of water not suited to drinking, as outlined in
current AWWA guidelines*;
2. Failures due to normal wear, accident, misuse, abuse, negligence, or
contamination in source water supplies;
3. Damage due to failure to follow operating instructions and maintenance
requirements or any damage, residential or commercial, resulting from Natural
Kitchen system or plumbing leaks.
4. Products that are altered, modified, or serviced in a manner not authorized by
NATURALLY FILTERED, LLC in writing;
5. Failure of goods due to use other than what was originally intended; and
6. Damage due to failure to follow published laws, regulations, and codes.
For servicing under this warranty, contact Naturally Filtered’s Customer
Service Department at 1-800-428-9419 and explain the problem in detail. Repair
or replacement of the filter by NATURALLY FILTERED, LLC requires proof of
purchase and may require the return of the filter to NATURALLY FILTERED, LLC
at your cost.
* For information regarding current AWWA standards, visit http://www.awwa.org
Naturally Filtered, LLC PO Box 1866, Alachua, FL 32616 USA
USA Toll Free 1-800-428-9419 • International Customers 1-386-462-0563
www.NaturallyFiltered.com
10
Warranty
The Natural Shower
Did you know that your body can absorb
up to 600% more contaminants in a 10
minute shower than you would drinking
the same water all day long?
The Natural Shower is the perfect
partner to your new Natural Kitchen.
It is the best performing NSF Certified
shower filter on the market. Most shower
filters reduce less than 90% of Chlorine
initially, and quickly drop off to 50
- 60% reduction. That’s leaving half the
Chlorine in your water!
The Natural Shower
reduces more than
98% of chlorine after 9
months and still reduces
over 89% after 1 year.
The Natural Home
The Natural Home offers
the best point-of-entry
chemical filtration
performance for homes
and small businesses,
effectively reducing
a broad spectrum of
contaminants such as
Chlorine, Chloramines,
THMs, VOCs, Heavy Metals,
and Iron for 5 -7 years.
Because The Natural Home
system treats the water as it enters
your home or office, you will have
peace of mind knowing that your water
is purified and enhanced.
The MG-10 model produces 10 gallons
per minute and is enough for a standard
family of four with a two to three bathroom
residence. The MG-30 produces 30 gallons per minute and is ideal for
large homes or small businesses.