Nauticam 36060 User manual

Current as of 2019-05-16
Zoom gear tube - Zoom Gear
Spring ring - Zoom gear
Macro Switch Block
- Zoom Gear
Macro switch gear
Locking ring
- Macro switch Gear
Positioning Block x3
- Macro Switch Gear
Inner groove
Screw x12
2. Align the alignment index on the ring with the line on the
lens before tightening the four screws. While tightening the
screws, make sure that the gaps on both sides are even and
the ring does not slip when turning at E-ZOOM mode.
36060 Macro Port and Zoom Gear Set for
Olympus 12-50mm EZ to use with
GH5/EM1X (for NA-GH5/EM1X)
Instruction Manual
FOREWORD
Thank you for your purchase of a NAUTICAM product.
At NAUTICAM, we pride ourselves in the ability to recognize the requirements
of professional as well as amateur underwater photographers and fulfill them
through the innovative designs of our products. We strive to achieve a high
level of user-friendliness by allowing stress-free installation and easy
operation of all important functions of the camera.
Please read this manual carefully before using the product, this will maximize
its performance as well as its lifetime.
WARRANTY
All NAUTICAM Products are warranted against any material and
manufacturing defects for two years from the date of purchase for consumer
use. This warranty only applies to products purchased from authorized
NAUTICAM dealers and does not extend beyond the original retail purchaser.
To return your product for service, please contact your regional authorized
service centre(s). Please note that this warranty only applies when the product
is purchased in the territory where the service centre is located.
NAUTICAM does not hold responsibility for damage, of any nature, to any
equipment used with and/or placed within our products.
NAUTICAM accepts no liability for any loss of captured images or the inability
to capture images even if it is due to the malfunctioning of our products.
Unauthorized modifications and/or repairs of our products will automatically
invalidate the warranty.
PRE-CAUTIONS
·After installation of the port combo, please make sure the o-ring (s) are
free from debris and uneven surface issues.
·A water-tight test without the camera inside the housing is highly
recommended after the changing of port and O-ring(s).
·Do not use lubricants from other brands with the silicone rubber O-ring
on this housing, only use the lubricant provided by NAUTICAM.
·Discontinue use immediately should you notice any leakage.
·Do not open the product in a wet or sandy environment. Protect the
interior from moisture and debris in order to prevent malfunction or
leakage.
·Defective products should be shipped to our distributors for service,
unauthorized disassembling and/or modifications could result in
malfunction or leakage.
IDENTIFICATION OF PORT PARTS
IDENTIFICATION OF ZOOM GEAR PARTS
MOUNTING THE GEAR ON A LENS
Macro Port with M77 thread for
Olympus M.Zuiko Digital ED 12-
50mm F3.5-6.3 EZ
Control knob
Plastic port cap
Rear port cap
Cold shoe
Two half-rings - Zoom Gear
Alignment index
Spare O-ring
Zoom gear ring - Zoom Gear
1. Mount the two half-rings on the lens zoom ring as indicated
in the diagram.
Gap between
the two half-rings

Current as of 2019-05-16
3. Align the alignment index on zoom gear tube with the
red dot on the lens and insert the tube onto the lens.
4. Align the spring ring with the lens as indicated in the
diagram. Then lightly push the ring towards the lens
until it cannot go any further.
Tip: To remove, pull out from the cover.
5. Align the pins on the tube with the holes in the gear
ring as indicated in the diagram. Then tighten the
three screws.
6. Align and tighten the screws with the Macro switch
block pressing on the lens MACRO button.
1. screws.
7. Align the inner groove of the macro switch gear with
the white dot on the front part of the lens. Then lightly
push the gear towards the lens until it cannot go any
further.
8. Tighten the macro switch gear by screwing the
locking ring into the thread on the front of the lens.
9. Align the positioning block onto the two gears. With
the longer ends inserted into the hole of the zoom
gear and the shorter ends sat into the groove of the
macro switch gear. Then tighten the two screws.
Repeat this with the other two blocks and check if
the lens can be switched between macro mode and
normal mode by turning the macro switch gear.
Repeat the above procedure if fail to switch.
10. To un-mount, reverse the above steps.
*When mounting the Olympus 12-50mm EZ lens with the
gear on the GH5/EM1X camera, or when removing them,
the lens must be set to the “Macro” position.

Current as of 2019-05-16
1. Make sure the control knob is at its most outwards
position before mounting/ un-mounting the port. The
knob should be left at this position until making sure
that the lens and zoom gear is properly installed.
MOUNTING THE PORT TO THE HOUSING
Correctly aligned
2. When properly installed, the lens should be perfectly
concentric with the port. If there is a slight misalignment,
check the position of the camera.
3. Engage the gear by pushing in the knob, then turn the
knob for about 45°both ways to check if the camera
switch between normal mode and Macro mode.
Remark: Nauticam supports only e-manuals. Please download
corresponding product manuals on Nauticam.com website, or
contact us for e-manuals.