Navkom R7 User manual

1
R7
INSTRUCTION MANUAL
EN
DOOR PROFILE BUILT-IN CONTROL UNIT

2 3
PLACING YOUR FINGER ON THE SENSOR PROPERLY
Users with smaller ngerprints, especially women and children, may need
to press the nger harder to achieve sucient coverage (applying pressure
spreads your nger).
1YOURFINGERPRINTMUSTCOVERATLEAST 70%OFTHESENSOR
SURFACE.
For most users, this is approximately in the middle of the nger pad, where
the ngerprint curves form the centre. Have a look at your ngerprints and
their features.
2PLACE YOUR FINGER IN THE CENTRE OF THE SENSOR AT THE
AREA WHERE THE FINGERPRINT IS MOST PRONOUNCED.
3DRY SKIN IS THE MOST COMMON CAUSE OF POOR READING.
If the nger needs to be pressed harder than usual to be read, the most
likely cause is dry skin on your nger. This is particularly common during
winter months. Make sure your skin is not unusually dry and use hand cre-
ams or moisturizing wipes or touch a damp surface lightly for this purpose,
but make sure your nger is not wet.
4DO NOT MOVE YOUR FINGER WHILE READING IS IN PROGRESS.
Wait for the device to beep to conrm a successful entry before moving
your nger.
6ENTER EACH USER FINGERPRINT MULTIPLE TIMES! ENTER
SEVERALFINGERSOFBOTHHANDSTOAVOIDPOSSIBLEPROBLEMS
DUE TO INJURED FINGERS.
This ensures a good reading can be taken regardless of the position of your
nger on the sensor and backup is provided in case of a nger injury.
5TO SUCCESSFULLY ENTER YOUR FINGERPRINT, PLACE YOUR
FINGER ON THE SENSOR 3 TIMES.
Only then will your ngerprint be saved. This ensures quality input and
good reading.
TABLE OF CONTENTS
PLACINGYOUR FINGER ON THE SENSOR PROPERLY 3
TECHNICAL DATA 4
MAINTENANCE 4
READER COMPONENTS AND FUNCTIONS 5
DOOR PROFILE BUILT-IN CONTROL UNIT 5
READER CONTROL MODES 6
TEST FUNCTION 6
FINGERPRINT READER SECURITY LOCKDOWN 7
BLUE LIGHT ON/OFF 7
RELAY 2 7
READER CONTROL MODES (door prole built-in control unit) 8
ANALOGUE READER CONTROLWITH DOOR PROFILE BUILT-IN CONTROL UNIT 9
ADMINISTRATOR FINGERPRINTS 9
ANALOGUE CONTROL BY PLACING YOUR FINGER ONTHE SENSOR 13
ADMINISTRATOR FINGERPRINTS 13
FACTORY RESET 15
HYBRID CONTROL 16
APP CONTROL 18
!NAVIGATE TO THE INSTRUCTIONS BY CLICKING ON FIELDS MARKED WITH

4 5
Our ngerprint readers do not require special maintenance, but you must make sure that the sensor is always cle-
an. If the reader is used with greasy or dirty ngers, dirt may start to accumulate on the sensor, which should be
cleaned with a soft, damp cloth. Dirt on the sensor may cause poor performance.
MAINTENANCE
• Capacity: 498 ngerprints (166 × 3)
• Supply voltage: 8-30 V, DC
• 2 relay outputs
• Maximum current on the relay: 3
• Relay trigger time: 1 - 60 s
• Maximum power: 1.8 A in analogue mode, 2.5 A in Wi-Fi mode
• Fast ngerprint recognition: <1.2s
• Operating temperature range: –20°C to +60°C
• Maximum ambient humidity up to: 100% IP65
• Fingerprints remain stored in memory even in the event of a power failure
• Capacitive sensor FPC1011F3
• User interface: 3-colour LED, beeper, 3 buttons on the control unit
• The reader creates a pattern from the biometric characteristics of the ngerprint, which is converted
into a code for ngerprint recognition by a special algorithm.
TECHNICAL DATA
WHENCLEANINGUNDERNOCIRCUMSTANCESUSE:AGGRESSIVECLEANERS,POLISHING
PASTES OR ACIDS! CLEANING OR SCRATCHING THE SENSOR SURFACE WITH HARD AND
SHARP OBJECTS MAY CAUSE DAMAGE TO THE SENSOR AND FAILURE OF THE DEVICE, WHICH
WILL RESULT IN THE WARRANTY BEING VOIDED.
READER COMPONENTS AND FUNCTIONS
BEFORE THE FIRST USE OF YOUR FINGERPRINT READER, IT IS RECOMMENDED TO RESET TO
FACTORY SETTINGS (Test Function remains on for 1 minute – see p. 5 for more info).
ONCE THE FINGERPRINT READER IS RESET, IT IS RECOMMENDED TO IMMEDIATELY ENTER THE
ADMINISTRATOR’S FINGERPRINTS.
IF THERE IS NO ACTIVITY WITHIN 8 MINUTES AFTER CONNECTING THE FINGERPRINT READER,
IT DEACTIVATES AUTOMATICALLY TO PREVENT UNAUTHORISED PERSONS FROM CONNECTING.
IN THIS CASE, TURN OFF THE FINGERPRINT READER POWER SUPPLY FOR MIN. 5 SECONDS (THE
EASIEST WAY TO DO THIS IS TO TURN OFF THE FUSE), THEN TURN THE FINGERPRINT READER
POWER SUPPLY ON AGAIN. IT IS RECOMMENDED YOU RESET THE DEVICE.
IF IT IS IMPOSSIBLE TO ENTER THE ADMINISTRATOR’S FINGERPRINTS IMMEDIATELY
AFTER CONNECTING THE FINGERPRINT READER, PLEASE TURN OFF THE POWER OF YOUR
FINGERPRINT READER UNTIL THE ADMINISTRATOR’S FINGERPRINTS ARE ENTERED.
1MULTICOLOUR LED
2FINGERPRINT SENSOR
Uses various colour signals for communicating the device’s
status and operations running.
When no operation is running, placing the saved nger on the
sensor opens the door.
3BEEPER
While an operation is running, light signals are accompanied by
sound.
1
2
3
DOOR PROFILE BUILT-IN CONTROL UNIT
The control unit is located in the door prole, next to the door loop. There are two function buttons
(1 and 2), and the R button for factory reset (located under the screw).
BUTTON 1
Analogue mode: ADDING ADMINISTRATORS OR USERS
Wi- mode: ACTIVATION/DEACTIVATION OF FREE PASSAGE
MODE
BUTTON 2
Analogue mode: DELETING USERS
Wi- mode: BLUE LIGHTING ON/OFF
BUTTON R
Factory reset.
To press this button, rst remove the screw. The button is
located under the screw.
1
2
R

6 7
No matter which control unit you have, when using the reader for the rst time, you can choose between three
dierent control modes: analogue, app or hybrid control. Description and instructions for each control mode can
be found below.
ANALOGUE CONTROL using buttons located on the control unit, by remote control or by placing your
nger on the sensor
APP CONTROL on your smartphone
HYBRID CONTROL - analogue reader control, using the app only to unlock doors and control LED lighting
READER CONTROL MODES
YOU CAN CHANGE THE CONTROL MODE AT ANY TIME BY RESETTING THE DEVICE TO FACTORY
SETTINGS AND STARTING TO OPERATE IT IN YOUR PREFERRED MODE.
Resetting the device to factory settings deletes the ngerprint database and all other settings.
In the event that a nger is placed on the sensor of the ngerprint reader seven times in a row, the reader will
not recognize it and will lock for 30 seconds.
After thirty seconds, the reader will be ready to be used again. The reader will lock again if a ngerprint which
cannot be recognized by the reader is placed on the sensor again seven times in a row. This time it will lock for
60 seconds.
After each unsuccessful attempt, up to seven attempts, the reader will be locked and the time will increase by 30
seconds, up to a maximum of 5 minutes. Each time the reader successfully recognizes a ngerprint, the count is
interrupted and resets to the beginning.
FINGERPRINT READER SECURITY LOCKDOWN
The test function is interrupted by a power outage or the addition of ngerprints.
Once the test function has elapsed, the device remains at factory settings and ready
for rst use.
TEST FUNCTION
X
GREEN
R
AFTER EACH FACTORY RESET, THE DEVICE REMAINS IN TEST FUNCTION FOR 1
MINUTE.
During this time, the sensor-LED ashes green.
DURING THIS TIME, ANY FINGERPRINT CAN UNLOCK THE DOOR.
WHILE THE READER IS LOCKED, THE PURPLE LED WILL FLASH AND THE READER WILL NOT
RESPOND TO FINGERPRINTS. PURPLE
PRESS AND HOLD THE RBUTTON FOR 10 SECONDS. THE
PURPLE LED BLINKS 5 TIMES ACCOMPANIED BY FIVE BEEPS.
All ngerprints, including the administrator’s, are erased from the
memory and the device is restored to factory settings. Any paired re-
mote controls and smartphones are disconnected as well.
In combination with the control unit built in the door prole, our ngerprint readers allow you to unlock additi-
onal (side or garage) doors, as well as the door the reader is installed in. Individual ngerprints can be assigned
to either open the additional door only or the main and additional door together.
To activate relay 2 with the selected ngerprint, complete the Optional step for activating relay 2 when
entering the ngerprint (both administrator and user), which is described in the Input procedures for admi-
nistrators and users section.
SKIP THIS STEP, IF YOU WANT THE FINGERPRINTTO OPEN THE FRONT DOOR ONLY.
The blue LED starts ashing immediately. Wait for three beeps before you release
the button.With this operation, only the blue LED that is lit in standby mode is turned
o. All other light signals remain active. Repeat the procedure to reactivate the blue
LED.
1 HOLD DOWN BUTTON 1 ON THE CONTROL UNIT FOR 10 SECONDS AND
WAIT FOR THE DEVICE TO BEEP 3 TIMES. THE BLUE LED TURNS OFF.
BLUE LIGHT ON/OFF
RELAY 2
FACTORY RESET
PURPLE
5 ×
If you are bothered by the blue LED that is constantly lit in standby mode, you can turn it
o.
AFTER EACH FACTORY RESET, THE DEVICE REMAINS IN TEST FUNCTION FOR 1 MINUTE.

8 9
ANALOGUE READER CONTROL WITH DOOR PROFILE BUILT-IN
CONTROL UNIT
Start by adding administrator ngerprints on the reader by pressing Button 1 on the control unit.
Perform the factory reset.
1
2
The rst three saved ngerprints have a special role and are called administrator ngerprints. These
ngerprints are entered by the administrator, i.e. the device owner. From the third memory spot onwards, only
user ngerprints can be entered. Entering ngerprints without the presence of an administrator is no longer
possible beyond the three memory spots.
1
ADMINISTRATORS
234 5 6 7 8 9 10
1. THE ADMINISTRATOR FINGERPRINTS ARE ONLY THE FIRST THREE FINGERPRINTS STORED IN THE
MEMORY
No further administrator ngerprints can be added after the rst three. Administrator ngerprints can be
three dierent ngers of the same person or ngerprints of dierent persons.
2. WHEN THE FIRST THREE MEMORY SPOTS ARE FILLED, ONLY USERS CAN BE ENTERED.
3. ADMINISTRATOR FINGERPRINTS SHOULD BE CAREFULLY CHOSEN, AND THE FINGERPRINTS
SHOULD BE CLEAR.
You need to be especially careful when entering administrator ngerprints, as these ngerprints cannot be
entered later, and can only be deleted by RESETTING TO FACTORY SETTINGS..
When entering the administrator ngerprint, select an uninjured nger with the clearest ngerprint.While
entering the ngerprints, keep your ngers clean and suciently moist, and for good readings follow the
instructions in the section PLACINGYOUR FINGER ONTHE SENSOR PROPERLY.
4. ADMINISTRATOR FINGERPRINTS ALSO OPEN DOORS AND ACTIVATE RELAY 2
The only dierence between the administrator and user ngerprint role is that administrator can perform
input and deletion operations.
5. WHEN THE READER MEMORY IS EMPTY, FINGERPRINTS CAN BE ENTERED BY ANYONE, SO
ADMINISTRATOR FINGERPRINTS SHOULD BE ENTERED AS SOON AS THE DEVICE IS INSTALLED TO
PROTECT IT AGAINST UNAUTHORIZED ACCESS.
USERS
ADMINISTRATOR FINGERPRINTS
Start by entering administrator ngerprints on the reader/by pressing Button 1 on the control unit/
Button A on the remote control.
READER CONTROL MODES (door prole built-in control unit)
When using the reader for the rst time, you can choose between three dierent control modes: analogue, app
or hybrid control. To choose the control mode, simply start using the reader in your preferred mode.
1
ANALOGUE CONTROL
is simple and allows basic functions. Analogue control is can be activated in 3 ways:
Find, name and add your reader in the X-Manager app.
APP CONTROL
provides a wide range of functions.
Click on its name to establish a connection.
Start entering administrator ngerprints in the app.
1
2
3
Find, name and add your reader in the X-Manager app.
HYBRID CONTROL
is an analogue reader control using the app only to unlock doors and control LED lighting.
1
Start by entering administrator ngerprints on the reader/by pressing Button 1 on the control unit/
Button A on the remote control.
Once the administrator’s ngerprints are entered, you can use the app only to unlock the door or
manage the LED lighting.
2
3
YOU CAN CHANGE THE CONTROL MODE AT ANY TIME BY RESETTING THE DEVICE TO FACTORY
SETTINGS AND STARTING TO OPERATE IT IN YOUR PREFERRED MODE.
Resetting the device to factory settings deletes the ngerprint database and all other settings.
WITH BUTTONS ON CONTROL UNIT
USE OF X-MANAGER APP
HYBRID CONTROL
WITH REMOTE CONTROL
ON THE SENSOR

10 11
1PRESS BUTTON 1 ON THE CONTROL UNIT TO
START THE ADMINISTRATOR FINGERPRINTS ENTRY
PROCEDURE.
The blue LED starts ashing.
2a IF YOU WANT THE ADMINISTRATOR FINGERPRINT TO ACTIVATE RELAY 2,
PRESS BUTTON 1.
2b IF YOU WANT THE ADMINISTRATOR FINGERPRINT TO SIMULTANEOUSLY
OPEN THE DOOR AND ACTIVATE RELAY 2, PRESS BUTTON 2.
OPTIONAL STEP FOR RELAY 2 ACTIVATION
IF YOU DON'T WANT TO ACTIVATE RELAY 2, SKIP THIS STEP
The orange LED will ash once and you will hear a beep. The entered administrator nger-
print will only activate relay 2.
The orange LED will ash twice and you will hear two beeps. The entered administrator n-
gerprint will open the door and activate relay 2 at the same time.
BLUE
ORANGE
1 ×
ORANGE
2 ×
3PLACE THE ADMINISTRATOR FINGER ON THE SENSOR
3 TIMES IN A ROW. EACH SUCCESSFUL ENTRY WILL BE
CONFIRMED WITH A SHORT BEEP. AFTER 3 ENTRIES, THE
FINGERPRINT IS SAVED - A LONG BEEP IS HEARD AND
THE GREEN LED LIGHTS UP.
A
GREEN
1 ×
ADMINISTRATOR FINGERPRINTS ENTRY PROCEDURE
3 ×
4REPEAT THE PROCEDURE WITH THE SECOND AND
THIRD ADMINISTRATOR FINGERS.
IF THE FINGERPRINT YOU ARE TRYING TO
ENTER IS TOO DAMAGED AND DOES NOT HAVE
A CLEAR ENOUGH STRUCTURE, THE RED LED WILL
LIGHT UP, THE DEVICE WILL BEEP 5 TIMES AND THE
OPERATION WILL BE STOPPED. CHOOSE A HIGH
QUALITY FINGERPRINT, MAKE SURE THE FINGER IS
CLEAN AND MOIST ENOUGH AND REPEAT THE
PROCESS. FOR EACH FINGERPRINT YOU WANT TO
SAVE, PLACE THE FINGER 3 TIMES ON THE SENSOR
TO ENSURE GOOD FINGERPRINT RECOGNITION.
1TOSTARTTHEUSERFINGERPRINTSENTRYPROCEDURE,
PRESS BUTTON 1ON THE CONTROL UNIT.
The blue LED starts ashing.
OPTIONAL STEP FOR RELAY 2 ACTIVATION
IF YOU DON'T WANT TO ACTIVATE RELAY 2, SKIP THIS STEP
BLUE
GREEN
1 ×
U
GREEN
1 ×
2FIRST, THE ADMINISTRATOR PLACES A FINGER ON THE
SENSOR.
For security reasons, the administrator must always conrm the
start of the user entry procedure.
After successful administrator recognition, the green LED will light
up and a beep will be heard.
If a non-administrative nger is placed on the sensor, the
device will not react and the blue LED will keep ashing. BLUE
Follow the instructions on the previous page.
3THE BLUE AND GREEN LEDS FLASH ALTERNATELY.
PLACE THE USER FINGERPRINT ON THE SENSOR 3
TIMES IN A ROW. EACH SUCCESSFUL ENTRY WILL BE
CONFIRMED WITH A SHORT BEEP. AFTER 3 ENTRIES,
THE FINGERPRINT IS SAVED - A LONG BEEP IS HEARD
AND THE GREEN LED LIGHTS UP.
A
BLUE
GREEN
USER FINGERPRINTS ENTRY PROCEDURE
3×
IF THE FINGERPRINT YOU ARE TRYING TO
ENTER IS TOO DAMAGED AND DOES NOT HAVE
A CLEAR ENOUGH STRUCTURE, THE RED LED WILL
LIGHT UP, THE DEVICE WILL BEEP 5 TIMES AND THE
OPERATION WILL BE STOPPED. CHOOSE A HIGH
QUALITY FINGERPRINT, MAKE SURE THE FINGER IS
CLEAN AND MOIST ENOUGH AND REPEAT THE
PROCESS. FOR EACH FINGERPRINT YOU WANT TO
SAVE, PLACE THE FINGER 3 TIMES ON THE SENSOR
TO ENSURE GOOD FINGERPRINT RECOGNITION.

12 13
1×
1TO START THE USER FINGERPRINTS DELETION
PROCEDURE, PRESS BUTTON 2ON THE CONTROL UNIT.
The blue LED starts ashing.
U
2FIRST, THE ADMINISTRATOR PLACES A FINGER ON THE
SENSOR.
For security reasons, the administrator must always conrm the
start of the user deletion procedure.
After successful administrator recognition, the green LED will light
up and a beep will be heard.
If a non-administrative nger is placed on the sensor, the
device will not react and the blue LED will keep ashing.
3GREEN AND RED LEDS WILL FLASH ALTERNATIVELY.
PLACE THE USER FINGER YOU WANT TO DELETE ON THE
SENSOR ONCE.
When the nger is successfully deleted, the LED will light
up 3 times and three beeps will be heard.
A
BLUE
GREEN
1 ×
BLUE
RED
GREEN
ORANGE
3 ×
USER FINGERPRINTS DELETION PROCEDURE
If a nger that is not saved in the memory is placed on
the sensor, the device will not react. The green and red
LEDS will continue ashing.
IF MORE THAN 1 FINGERPRINT OF THE SAME USER
IS SAVED, DELETE THE FINGERPRINTS OF ALL
FINGERS!
ANALOGUE CONTROL BY PLACING YOUR FINGER ON THE
SENSOR
Start by adding administrator ngerprints by placing your nger on the sensor for 5 seconds.
Perform the factory reset.
1
2
The rst three saved ngerprints have a special role and are called administrator ngerprints. These
ngerprints are entered by the administrator, i.e. the device owner. From the third memory spot onwards, only
user ngerprints can be entered. Entering ngerprints without the presence of an administrator is no longer
possible beyond the three memory spots.
1
ADMINISTRATORS
234 5 6 7 8 9 10
USERS
ADMINISTRATOR FINGERPRINTS
1. THE ADMINISTRATOR FINGERPRINTS ARE ONLY THE FIRST THREE FINGERPRINTS STORED IN THE
MEMORY
No further administrator ngerprints can be added after the rst three. Administrator ngerprints can be
three dierent ngers of the same person or ngerprints of dierent persons.
2. WHEN THE FIRST THREE MEMORY SPOTS ARE FILLED, ONLY USERS CAN BE ENTERED.
3. ADMINISTRATOR FINGERPRINTS SHOULD BE CAREFULLY CHOSEN, AND THE FINGERPRINTS
SHOULD BE CLEAR.
You need to be especially careful when entering administrator ngerprints, as these ngerprints cannot be
entered later, and can only be deleted by RESETTING TO FACTORY SETTINGS..
When entering the administrator ngerprint, select an uninjured nger with the clearest ngerprint.While
entering the ngerprints, keep your ngers clean and suciently moist, and for good readings follow the
instructions in the section PLACINGYOUR FINGER ONTHE SENSOR PROPERLY.
4. ADMINISTRATOR FINGERPRINTS ALSO OPEN DOORS AND ACTIVATE RELAY 2
The only dierence between the administrator and user ngerprint role is that administrator can perform
input and deletion operations.
5. WHEN THE READER MEMORY IS EMPTY, FINGERPRINTS CAN BE ENTERED BY ANYONE, SO
ADMINISTRATOR FINGERPRINTS SHOULD BE ENTERED AS SOON AS THE DEVICE IS INSTALLED TO
PROTECT IT AGAINST UNAUTHORIZED ACCESS.

14 15
IN THIS CONTROL MODE, INDIVIDUAL FINGERPRINTS CANNOT BE DELETED. YOU CAN
ONLY DELETE THE ENTIRE FINGERPRINT DATABASE (INCLUDING ADMINISTRATORS) BY
RETURNING THE DEVICE TO FACTORY SETTINGS.
1TO START ENTERING ADMINISTRATOR FINGERPRINTS, PLACE YOUR FINGER
ON THE SENSOR FOR 5 SECONDS.
The blue LED starts ashing. BLUE
2 PLACE THE ADMINISTRATOR FINGERPRINT ON THE
SENSOR 3 TIMES IN A ROW. EACH SUCCESSFUL ENTRY
WILL BE CONFIRMED WITH A SHORT BEEP. AFTER THREE
ENTRIES, THE FINGERPRINT IS SAVED - A LONG BEEP IS
HEARD AND THE GREEN LED LIGHTS UP.
A
GREEN
1 ×
ADMINISTRATOR FINGERPRINTS ENTRY PROCEDURE
3 ×
3 PLACE THE FIRST ADMINISTRATOR FINGER ON THE SENSOR FOR 5 SECONDS,
THEN ENTER THE SECOND ADMINISTRATOR FINGER 3 TIMES IN THE SAME WAY AS
THE PREVIOUS ONE.
4REPEAT THE SAME PROCEDURE WITH THE THIRD ADMINISTRATOR FINGER.
A
IF THE FINGERPRINT YOU ARE TRYING TO
ENTER IS TOO DAMAGED AND DOES NOT HAVE
A CLEAR ENOUGH STRUCTURE, THE RED LED WILL
LIGHT UP, THE DEVICE WILL BEEP 5 TIMES AND THE
OPERATION WILL BE STOPPED. CHOOSE A HIGH
QUALITY FINGERPRINT, MAKE SURE THE FINGER IS
CLEAN AND MOIST ENOUGH AND REPEAT THE
PROCESS. FOR EACH FINGERPRINT YOU WANT TO
SAVE, PLACE THE FINGER 3 TIMES ON THE SENSOR
TO ENSURE GOOD FINGERPRINT RECOGNITION.
The blue and green LEDs ash alternately.
U
GREEN
1 ×
A
USER FINGERPRINTS ENTRY PROCEDURE
1TO START ENTERING USER FINGERPRINTS, PLACE THE ADMINISTRATOR
FINGER ON THE SENSOR FOR 5 SECONDS.
BLUE
GREEN
PURPLE
5 ×
BLUE
RED
The blue and red LEDs ash alternately.
3 ×
FACTORY RESET
1 PLACE THE ADMINISTRATOR FINGER ON THE SENSOR
FOR 15 SECONDS.
2CONFIRM THE FUNCTION BY PLACING THE ADMINISTRATOR FINGER ON THE
SENSOR TWO TIMES. THE PURPLE LED BLINKS 5 TIMES ACCOMPANIED BY 5
BEEPS.
* If the administrator’s ngerprint has not yet been entered, the reset can be done with any nger
within 8 minutes after the rst connection. In this case, the blue LED turns o.
All ngerprints, including the administrator’s, are deleted from the memory and the device
is restored to factory settings. Any paired remote controls are deleted as well.
3PLACE THE USER FINGERPRINT ON THE SENSOR
3 TIMES IN A ROW. EACH SUCCESSFUL ENTRY WILL
BE CONFIRMED WITH A SHORT BEEP. AFTER THREE
ENTRIES, THE FINGERPRINT IS SAVED - A LONG BEEP IS
HEARD AND THE GREEN LED LIGHTS UP.
IF THE FINGERPRINT YOU ARE TRYING TO
ENTER IS TOO DAMAGED AND DOES NOT HAVE
A CLEAR ENOUGH STRUCTURE, THE RED LED WILL
LIGHT UP, THE DEVICE WILL BEEP 5 TIMES AND THE
OPERATION WILL BE STOPPED. CHOOSE A HIGH
QUALITY FINGERPRINT, MAKE SURE THE FINGER IS
CLEAN AND MOIST ENOUGH AND REPEAT THE
PROCESS. FOR EACH FINGERPRINT YOU WANT TO
SAVE, PLACE THE FINGER 3 TIMES ON THE SENSOR
TO ENSURE GOOD FINGERPRINT RECOGNITION.

16 17
Add your reader in the X-Manager app.
Perform the factory reset.
1
2
Start by entering administrator ngerprints on the reader/by pressing Button 1 on the control unit/
Button A on the remote control.
3
HYBRID CONTROL
FINGERPRINT ENTRY AND READER CONTROL
Once the administrator’s ngerprints are entered, you can use the app only to unlock the door or manage
the LED lighting.
4
Download the X-manager app to your smartphone or tablet from the Google Play Store
(Android) or the App Store (Apple).
CONNECTING THE PHONE TO THE READER
APP FUNCTIONS
Pressing the Activate- relay2 tabwill activate
the device connected to relay 2 (alarm, garage
door, side door, etc).
Pressing the Touch to open - relay 1 tab will
unlock the door.
LED settings: If there is LED lighting in the
door, it can be connected to the system and
controlled by the X-manager. It is possible to
adjust the brightness (1% to 100%) and the
schedule for turning the lighting on/o:
- 24H: The LED lighting will be switched on
continuously.
- Auto: The LED lighting will automatically turn
on at sunset and turn o at sunrise.
- Custom:You can set the switch-on and switch-
o times yourself. You can set two intervals in
the day when the lighting will be on.
Relay opening time: The length of time
during which the relay is switched on can be
adjusted to between 1 and 60 seconds. This
setting is useful when using an electric strike.
Blue backlight: if the blue backlight that
lights up when the reader is in standby mode
bothers you, you can turn it o.
2
3
1
4
5
1
2
3
4
5
Once the ngerprints are entered, you can connect to the reader and control both relays and LED settings
in the app.
APPLE
ANDROID
ON THE SENSOR
WITH REMOTE CONTROL
WITH BUTTONS ON CONTROL UNIT

18 19
APP CONTROL
IMMEDIATELYAFTERINSTALLINGANDCONNECTINGTHEDEVICE,ITISRECOMMENDED
TOCONNECT ATLEAST 1 PHONEWITHTHE DEVICE.OTHERWISEWI-FI IS DEACTIVATED
AFTER 8 MINUTES FOR SECURITY REASONS. IN THIS CASE, THE DEVICE MUST BE
DISCONNECTED FROM THE POWER SUPPLY AND CONNECTED AGAIN BEFORE BEING
CONNECTED TO THE PHONE FOR THE FIRST TIME.
X-manager
Download the X-manager app to your smartphone or tablet from the Google Play Store
(Android) or the App Store (Apple).
Find, name and add your reader in the X-Manager app.
Click on the name to establish a connection.
Start entering administrator ngerprints in the app.
2
3
4
Perform the factory reset.
1
ON/OFF FREE ENTRANCE MODE
1TO ACTIVATE, PRESS BUTTON 1ON THE CONTROL UNIT.
The blue LED starts ashing.
BLUE
GREEN
2THE ADMINISTRATOR CONFIRMS THE OPERATION WITH
THEIR FINGERPRINT.
AS LONG AS THE FREE ENTRANCE MODE IS ON, THE GREEN
LED REMAINS ON.
Hold button 1 until the green LED is replaced by the blue one. BLUE
A
For security reasons, the administrator must always conrm the
operation.
3TODEACTIVATE,PRESS BUTTON1ONTHE CONTROLUNIT.
BLUE LIGHTING ON/OFF
BLUE
FACTORY RESET
The purple LED ashes 5 times and you hear 5 beeps. All
ngerprints stored in the memory, including administrator
ngers, will be erased and the device will be reset to factory
settings.
TO PRESS THIS BUTTON, FIRST REMOVE THE SCREW. THE
BUTTON IS LOCATED UNDER THE SCREW. PRESS AND
HOLD THE RBUTTON FOR 10 SECONDS. PURPLE
5 ×
HOLD BUTTON 2 UNTIL THE BLUE LED IS TURNED ON/OFF.
BUTTON FUNCTIONS on the door prole built-in control unit
If you have a door prole built-in control unit, but you wish to operate the reader using the app, buttons 1 and 2
will serve as shortcuts to turn on/o the free passage mode and blue lighting.

20 21
Every new reader needs to be added in the X-manager app
before it can be used. If more than one reader is connected to
a single X-manager app, you must set up the connection to the
readers one at a time. The rest of the readers should not be
connected to a power supply at the time of the rst connection.
CONNECTING THE PHONE TO THE READER
ANDROID
SEARCHING DEVICES
ADD A DEVICE
SCAN QR CODE
Press +and then SEARCH icon.
Press ''Connect''.
Enter the desired device name and press ADD.
1
2
3
1
2
3
CONNECTING AN ADDITIONAL PHONE TO THE READER
A single reader can be managed with more than one phone.
DETAILS
4
5
6
On the phone that the reader is already
connected to, press the iicon next to the reader
name.
Two options appear on the screen:
Press the SCAN QR
CODE icon on the
new phone
QR CODE which you
can scan using the
new phone
PASSWORD which
you can manually
enter in the new
phone
Press the ADD A
DEVICE icon on the
new phone
4
5
8
7
6
7
8
OR
Press and hold the name of the reader. When prompted, conrm the disconnection.
DISCONNECTING THE READER
* If you have problems connecting an additional phone, turn oWi- on the already connected phone.

22 23
APPLE
Every new reader needs to be added in the X-manager app
before it can be used. If more than one reader is connected to
a single X-manager app, you must set up the connection to the
readers one at a time. The rest of the readers should not be
connected to a power supply at the time of the rst connection.
CONNECTING THE PHONE TO THE READER
Press ADD and then START.
Conrm the connection by pressing Join.
Enter the desired device name and press SETUP.
1
2
3
SEARCHING DEVICES
SCAN QR CODE
ADD A DEVICE
8
7
2
3
1
CONNECTING AN ADDITIONAL PHONE TO THE READER
A single reader can be managed with more than one phone.
DEVICE INFO
On the phone that the reader is already
connected to, press the iicon next to the reader
name.
Two options appear on the screen:
Press Scan QR code
on the new phone
QR CODE which you
can scan using the
new phone
Show password:
the PASSWORD is
displayed, which
you can enter
manually in the new
phone
Press Manual
setup on the new
phone
4
5
8
7
6
4
6
Press the iicon next to the reader name. Press DELETE. When prompted, conrm the
disconnection.
9
9
APPLE
DISCONNECTING THE READER

24 25
12 3 4
Enter the person’s name.
Choose either administrator or user rights. An administrator can perform
all functions including deleting other users and administrators. A user can
only open the door.
Choose the relay that the person will activate (relay 1, relay 2 or relays 1 and
2 together).
3 ngerprints for the person must be entered. Place the person’s nger
on the sensor 3 times in a row. The app will conrm every time the
ngerprint is saved. After three entries, the saving is complete.
Additional ngerprints for any person can also be entered later, but always
enter each nger 3 times. This ensures quality input and good reading.
The reader has a capacity of 498 dierent ngerprints. Any person
can have any number of ngerprints entered, but always at least 3
ngerprints (= 1 entry).
We recommend that every person has several ngerprints entered.
PRESS THE GREEN TAB TO START ADDING PEOPLE.
ADDING PEOPLE
1
2
3
4

26 27
3
1
2
4
5
The settings cannot be changed after the person has been entered.You
need to delete the person and add them again with dierent settings.
Administrators are indicated in orange and users in light brown.
Certain data is displayed under the name of each person:
 level of rights (User/Administrator)
 number of entered ngerprints
 relay(s) which this person will activate
You can enter additional ngerprints for any person at any time.This
can be done by pressing the +icon.
Users can have schedules assigned to them by pressing the icon of the
clock. You need to use the schedules beforehand.When the schedule
is active, the power icon turns green. Each user can have one schedule
assigned.
Everyadministratorcandeleteusersandotheradministrators.Oneadministrator
must always remain in the database and can be deleted only by Factory Reset.
The persons on the list can be deleted by pressing the Bin icon.
LIST OF ENTERED PEOPLE
1
2
4
3
5

28 29
1
2
4
3
5
6
7
All security functions can be performed only with the conrmation of the administrator’s
ngerprint.
Device name
Free entrance mode: enabling this mode allows the door to be opened
by any ngerprint, even if it is not stored in the database.The period
during which free entrance mode is switched on can be adjusted (1 to 1440
minutes), after which it is automatically turned o. As long as the free
entrance mode is active, the green LED remains lit.
Relay output time: The length of time during which the relay is
switched on can be adjusted to between 1 and 60 seconds. This setting is
useful when using an electric strike.
Blue backlight: if the blue backlight that lights up when the reader is in
standby mode bothers you, you can turn it o.
Database import/export: the ngerprint database can be transferred
from one reader to another.
1. Press the Export button on the source reader. This is conrmed by an
administrator.
2. Connect to the new reader and press the Import button. If an
administrator has already been entered on the new reader, their ngerprint
is required to conrm the import. If the database on the new reader is
empty, this step does not require conrmation.
3. Activation of the transferred database needs to be conrmed by an
administrator of the source reader.
SETTINGS
LED settings: If there is LED lighting in the door, it can be connected to
the system and controlled by the X-manage. Instructions are on the next
page.
System: software version, list of paired devices, adding remote controls.
1
2
4
3
5
6
7

30 31
1 2 3
LED SETTINGS
24H: The LED lighting will be switched on continuously.
Auto: The LED lighting will automatically turn on at sunset and turn o at
sunrise (depending on the location of the phone).
Custom: You can set the switch-on and switch-o times yourself. You can
set two intervals in the day when the lighting will be on.
IfthereisLEDlightinginthe door,itcanbe connectedtothesystemand controlled bytheX-manager.
It is possible to adjust the brightness (1% to 100%) and the schedule for turning the lighting on/o:
1
2
3
1
2
3

32 33
1
2
3
REVIEW OF THE LAST 100 EVENTS
The following events are monitored:
 all successful entries (users and administrators)
 all attempts to enter outside the scheduled time (the schedule must be
turned on and assigned to a user)
 temporary reader blockage
The entire history cannot be deleted. The new events overwrite
the oldest events so that the combined number of events is always
100.
HISTORY
Pressing the“Activate - relay 2”tab will activate the device connected to
relay 2 (alarm, garage door, side door, etc.).
The user or administrator can unlock the door by clicking on the“Touch to open”tab. Clicking on
the“Activate relay 2”tab activates relay 2.
Pressing the“Touch to open - relay 1”tab will unlock the door.
UNLOCK THE DOOR and ACTIVATE RELAY 2 WITH THE APP
1
2
3

34 35
1
2
4
3
56
SCHEDULES CAN BE ASSIGNED TO USERS TO LIMIT THEIR ENTRANCE TIME
There are three options to limit access for individual days of
the week:
 unlimited 24h access
 no access
 limited access (from – to)
Click on the Add tab to start assigning a schedule.
Write the name of the schedule.
Once you have entered the desired settings, press the SAVE button.
When the schedule is saved, it automatically becomes active. This is
indicated by the green Power icon.
Each schedule can be deactivated by pressing the Power icon, which
then turns white. If the deactivated schedule was assigned to any users,
those users have unlimited access. The Clock icon next to the user is
coloured white.
A schedule can be deleted by pressing the Bin icon. If the deleted
schedule has been assigned to any users, they gain unlimited access.
Up to ve schedules can be created.
SCHEDULES
1
2
4
3
5
6