NBB SR8063 User manual

Assembly Instructions
Shelter type: SR8063
SR8063-01-02112021-USA

20
8
8
8
18
9
11
1
2
5
3
1
4
12
9
7
16
13
21
2
Exploded View

3
PARTS LIST
ITEM
NO.
PART NUMBER
DRG number Size (inch) IMAGE
QTY.
1 S1 Frame SC1 78.74 x 40.74 7
2 Post P1
P1
78.75 x 40.5 1
3 S3C Frame S3 1
4 JF1 Bracket
JF1
8.7 x 1.6 10
5 FT1 BRACKET
FT1
4.3 x 3.9 x 1.6 3
6 DR Bracket
DR
4.3 x 1.6 x 2 12
7 AR2R 2m Pitch Rafter
AR2R
85.75 4
8
AR2POA AR2 Roof
Panel outer ALU
AR2POA
45.5 x 41.3 4
9
AR2IS 2m Pitch Infill
Panel Shallow
AR2IS
85 2
10
AR2TS 2m Apex Roof
Trim strip
AR2TS
45.5 x 2.3 4
11 FT3 Bracket
FT3
4.3 x 3.9 x 3.1 7
12 ST5 Roof Tie ST5 60.75 1
13 CB1 Bracket CB1 4.3 x 4.3 x 1.6 7
14
Roof centre lower
trim outer
AR2CLTO-03 41.4 2
15
Roof centre lower
trim inner
AR2CLTI-02 40.74 1
16
Roof F Section
Outer
ARFSO 41.5 4
17
ARFSI Apex Roof F
Section Inner
ARFSI 40.75 2
18
AR2PIA AR2 Roof
Panel inner ALU
AR2PIA 45.5 x 40.5 2
19
Roof centre upper
trim outer
AR2CUTO-02 41.5 2
20
Roof centre upper
trim inner
AR2CUTI 40.75 1
21
40x40 Plastic End
Cap
EC40 1.6 x 1.6 3

4
FIXINGS

83.07
123.82
MEASURE THE WIDTH AND DEPTH
OF THE SHELTER TO CHECK
CORRECT ALIGNMENT.
Please note 1.5" Tech Screws
are for roof panels only
S1C
S3C
CB1
JF1
CB1
CB1
CB1
JF1
Ensure correct
alignment on all corners
JF1
Step 1
Assemble S1C frames to make up the main structure using CB1
brackets for the corners and JF1 brackets for the straight joints.
5

ST5
JF1
CB1
P1
ST5
P1
Step 2
Use JF1 and CB1 brackets to attach the P1 post and ST5 Tie bar .
6

AR2IS
DR
AR2IS
AR2R
AR2R
AR2R
40.75 40.75 40.75
FRONT VIEW
Step 3
Attach A2R2 rafters unsing DR brackets. Secure the End Panels to the
frames using 1" Tech Screws. The end rafters need to be placed in position at the
same time as the AR2IS .
7

Step 4
AR2CLTO
AR2CLTI
AR2CLTI
ARFSO
ARFSO
ARFSI
ARFSO
ARFSO
ARFSI
AR2CLTO
AR2CLTO
ARFSO
ARFSO
ARFSI
ARFSI
ARFSO
ARFSO
AR2CLTI
Attach the AR2CLTI and AR2CLTO to the top of the rafters. The ARFSI and
ARFSO parts are to be attached to the lower part of the rafter as shown
below.
8

AR2POA
AR2TS
FT3
AR2TSAR2TSAR2TS
AR2POA
AR2POI
AR2POA
AR2POA
AR2POI
FT3
FT1
FT1
FT1
FT3
AR2CUTO
AR2CUTO
AR2CUTI
Align the outer roof panels AR2POA with the outer edges of the shelter and
space the AR2POI panels central. Use the AR2TS strips to seal the gap
between the roof panels and cap off the top with the AR2CUTO/AR2CUTI.
Once the shelter is in the final position it can be secured to the ground
using FT3 and FT1 brackets and the concrete bolts.
9
Step 5

123.8
83
10
PLAN VIEW
OVERALL DIMENSIONS AND GROUND FIXING POSITIONS
Suggested size for concrete base: 8" oversized on all 4 sides.