nbf Signature Series User manual

Top Panel-1pc Modesty Panel-1pc Right Base Leg-1pc
Left Base Leg-1pc
HARDWARE & TOOLS
COMPONENTS
Tools Required for Assembly
Philips Screw Driver for
Cam Lock
INSTRUCTIONS - We don’t recommend using power tools when installing Cam Posts.
72X30" Height Adjustable Desk
ASSEMBLY INSTRUCTIONS
IDT7230HA/IDBHAB
Cam Post
AB C D
E G
Congratulations on the purchase of your new Signature Series product!
IAllen Screw M4X20mm
STEP 1
Cam Post-5pcs Wood Dowel
Ø8*30mm-3pcs
Screw
M6X15mm-5pcs
Cam Lock-5pcs
Screw
Ø6X33mm-8pcs Cam Sticker-5pcs
E F G H
I J K
Allen Wrench 4mm-1pc
M
L
Allen Wrench 5mm-1pc
N
Mntg Bracket
50*30*2mm-2pcs
Screw
Ø4X20mm-9pcs
X4E
X4G
X4J
D
B
X2F
X2K
X8L
Wire Management Tray-2pc
P
HARDWARE & TOOLS
Control Box
-1pc Controller-1pc Screw
Ø5X20mm-3pcs
Power cord
-1pc
RST U Screw
Ø4X14mm-3pcs
VTools Required for Assembly
Philips Screw Driver for
Screw Ø5X20mm
U
Screw Ø4X14mm
V
NOTE:
Hardware is packed with
carton ALCB2 / ALCB3.
NOTE:
Hardware is packed with
carton IDT7230HA
B
C
D
BCD
IDBHAB
IDT7230HA

Congratulations on the purchase of your new Signature Series product!
INSTRUCTIONS - We don’t recommend using power tools when installing Cam Posts.
Install the Top (A) to the Legs(C,D) by Screw (I);
X8 I
X1N
Uninstall the Frame Mounting
Screws, Qty 2, with Wrench (N).
Install Wire Management
Tray (P) to Frame using
Screws (H) and Wrench (M).
Re-install Frame Screws thru
Wire Management Tray.
X4H
STEP 2
IDT7230HA/IDBHAB
X2P
TWO PEOPLE REQUIRED
X2V
STEP 3
72X30" Height Adjustable Desk
ASSEMBLY INSTRUCTIONS

Control Box
Controller
Power Cord
IDT7230HA/IDBHAB
STEP 4
Connect power for Control Box(R) using the
Power Cord(T) and connect Controller(S) into
the Control Box(S); Plug Power Cord(T) into
outlet and proceed with Controller Initialization.
See User Manual;
72X30" Height Adjustable Desk
ASSEMBLY INSTRUCTIONS
Congratulations on the purchase of your new Signature Series product!

72X30" Height Adjustable Desk
ASSEMBLY INSTRUCTIONS
Congratulations on the purchase of your new Signature Series product!
IDT7230HA/IDBHAB
Make sure no obstacles are in the desk's path.
Make sure the desktop is not touching any walls.
Make sure all cords are appropriate length to accommodate
the change in height.
IMPORTANT: You must INITIALIZE the desk prior to first use.
Controller Initialization- Press and hold the Down button on the controller until the desk
reaches its lowest height, slightly raises, and stops. Release the down button, your desk
is now ready for use. (Following the "USER MANUALS" to use your desk)
TROUBLESHOOTING
If the table is not functioning properly it may need to be reset.
Unplug the power cord for 20 seconds.
Plug the power cord back in and follow the RESET procedures.
If the error message persists after the reset procedure, please contact your dealer.
If the height between the legs exceeds 1.5 inches, stop the reset procedure,
please contact your dealer.
INSTRUCTIONS