nbf Signature AT WORK Series User manual

COMPONENTS
INSTRUCTIONS
A
H
B
HARDWARE & TOOLS
Desk TOP -1pc Support Beam-1set CLifting Leg - 2pcs DFoot - 2pcs EBracket- 2pcs FControl Box- 1pc GDisplay- 1pc
ASSEMBLY INSTRUCTIONS
Congratulations on the purchase of your new Signature Series product!
Screws M8*16mm
- 8pcs
Screws M6*14mm
- 8pcs
IJ
Adjustable Glide - 4pcs
Loosen the 4 screws of beam using Allen Key(4mm),
adjust the beam to proper position to fit the Desk Top.
(According to the predrilled holes on the TOP,see STEP 5)
KScrews M6*10mm
- 4pcs LScrews M6*12mm
- 8pcs
MRubber Cushion - 6pcs NScrews 3.5*19- 2pcs OScrews 4.8*19- 8pcs PAllen Key(4mm) - 1pc QAllen Key(5mm) - 1pc
AT WORK-Electric Motor Adjustable Desk
STEP 1 STEP 2
AW-ST4824/AW-ST6024/AW-ST7224
AW-AK2RT-ZF3
Tools Required for Assembly
Philips Screw Driver for
Parts N and O
L X4
J X8
P
B
C
C
P
P

INSTRUCTIONS
ASSEMBLY INSTRUCTIONS
Congratulations on the purchase of your new Signature Series product!
STEP 3 STEP 4
STEP 6
STEP 5
AT WORK-Electric Motor Adjustable Desk
AW-ST4824/AW-ST6024/AW-ST7224
AW-AK2RT-ZF3
QDE
E
D
P
I X8
H X4
M X6
L X4
A
O X6
O X2
K X4
N X2
G
P
F
Predrilled holes for the
beam attachment.

INSTRUCTIONS
ASSEMBLY INSTRUCTIONS
Congratulations on the purchase of your new Signature Series product!
STEP 7
AT WORK-Electric Motor Adjustable Desk
AW-ST4824/AW-ST6024/AW-ST7224
AW-AK2RT-ZF3
Connect the control box to the handset and to the motor.
Operation Guide
1.Normal Operation
Adjust the desk to the desired height by pressing and holding the “∧” or “∨” button.
2.Setting the Memory Function
When the desk is at the desired height, press and hold the “M” button until the display flashes.Then press “1” to set
position one. Repeat this procedure for up to four desired settings. These settings are saved in the device’s memory,
and will remain even if the desk is unplugged.
3.System Initialization and Reset
To reset the system, press and hold both the “∧” and “∨” buttons at the same time. After a moment, the desk will
begin to lower. Wait until the desk reaches its lowest point, indicated by a beep. The system memory is now cleared
and reset.
4.Display Format
To change the display from centimeters to inches, press and hold the “1”, “2”, and “M” buttons at the same time for
5 seconds.The display will flash “C-E”. Within 5 seconds, press the 1 key for centimeters, or press the 2 key for inches.
If this procedure does not work, reset the system and try again.
5.Normal Maintenance
Save wrenches and tighten screws/bolts every 6 months.
6.Notice
1.This product should only be used within its technical parameters, for its intended use.
2.This system should be kept dry and away from corrosive gas.
3.Avoid rapid, repeated stress on adjustment motor.
4.Always use two people to lift and move this desk.
5.Max weight limit:233.2lb(106kg).