nbf MORGAN User manual

WWW.NBF.COM
PARTS INSTRUCTIONS
PART DESCRIPTION QTY
1Casters 5
25-Star Base 1
3Telescoping Cover 1
4Cylinder 1
5Seat Plate 1
6A Left Arm 1
6B Right Arm 1
7Seat Cushion 1
8Back Cushion 1
9
Back Support Plate
(Already attached to
the back cushion)
1
10 1
" Screws 2
11 /8" Screws 2
13 1½" Screws 8
14 Plastic Caps 4
15 Hexagonal Wrench 1
t Seat Height:
, lean forward and reach under the
he chair to find the handle. Lift the
INSTRUCTIONS
A. Remove all parts from the carton and separate them into part number groups as indicated in the parts list.
B. To begin assembly, place the 5-star base (2) upside down and insert casters (1) into the bottom of base (2).
C.
D. Place the telescoping cover (3) over the the cylinder (4) and rest it on the base (2).
E. Attach the seat plate (5) to the bottom of the seat cushion (7) (with front of seat plate facing the front of the
seat cushion) by using 1 /8" screws (10) into the front holes of the seat plate (5) and /8" screws (11) into the
rear holes of the seat plate (5) and tighten the screws.
F. Align the back cushion (8) with the seat cushion (7) by positioning the back support plate (9) over the seat
plate (5) with 1¼" screws (12).Do not tighten the screws completely.
G. Attach the arms (6A & 6B) respectively on each side onto the bottom of the seat cushion (7) and the sides
of back cushion (8) by using 1½" screws (13). Tighten all the screws. Remember to tighten the screws on the
back support plate.
H. Place the plastic caps (14) into the two arm holes on each arm.
I. Place the assembled chair on top of the cylinder (4) and press down until fully engaged.
J. Periodically (every 90 days) make sure that the screws are still fully tightened.
CUSTOMER SERVICE HOTLINE
800-626-6060
ATTENTION:
Make certain to fully tighten all screws
before using chair.
A S S E M B LY I NSTRUC T I O N S
Congratulations on the purchase of your new Signature Series chair!
MORGAN HIGH-BACK CHAIR
12 1¼" Screws 4
7
5 7

OPERATING FEATURES
WWW.NB F.CO M
1. TO ADJUST SEAT HEIGHT:
While seated, lean forward and reach under the right side
of the chair to locate the handle. Lift the handle and raise
your body up slightly to allow the chair to rise to the desired
height. To lower the seat, lift the handle while applying more
weight downward on the seat. The chair will descend until the
handle is released or the chair reaches the lowest position.
2. TO OPERATE TILT LOCKOUT:
lockout bar. Slide the bar to the left (toward the outside of the
chair), all the way out, to allow the chair to tilt backwards. To
lock the chair in the vertical position, sit upright and push the
bar to the right (toward the center of the chair).
3. TO ADJUST TENSION ON THE TILT:
Reach under the front center of the chair, grasp the round
knob and turn counterclockwise to make the tilt mechanism
knob clockwise until the desired resistance is found.
1. To Adjust Seat Height:
While seated, lean forward and reach under the
right side of the chair to find the handle. Lift the
OPERATING INSTRUCTIONS
11
12
13
WARNINGS
1. This product should be used by only one person at a time.
2. Do not use this chair unless all bolts, screws and knobs are
securely tightened.
3. Save the hexagonal wrench. Check that all bolts, screws and
knobs are tight every three months or as needed.
4. Dispose of packing material properly. Do not use the plastic
cover as a head covering. It may cause suffocation.
5. Do not use the chair as a stepladder.
6. Use this chair for its intended purpose only.
7. The casters sold with this chair are intended for use on
carpet. They are not recommended for use on tile or hard-
ASS E M B LY I NSTRUCTION S
MORGAN HIGH-BACK CHAIR