nbf Signature Series User manual

Organize your parts and hardware. You will need (2) people, a Phillips head screwdriver and rubber mallet.
800-558-1010
www.NBF.com
4-door Hutch • INSTRUCTIONS
CARTONS: HD71
Parts :
HD-A: Back Panel
(69” x 31” x 1”)
Quantity: 1
HD-E: Left Side
(15” x 31” x 1”)
Quantity: 1
HD-G: Top
(71” x 15” x 1”)
Quantity: 1
HD-B: Sliding Door
(17.25” x 12.75” x 1”)
Quantity: 4
HD-C: Divider
(14” x 13” x 1”)
Quantity: 1
IMPORTANT NOTICE:
Place all wooden parts on a clean and smooth surface such as a rug or carpet to avoid the parts from being scratched.
Check to be sure that you have all parts and hardware.
Remove all wrapping materials, including staples & packing straps before you start to assemble.
Do not tighten all screws/bolts until completely assembled.
Keep all hardware parts out of reach of children.
Any problems or questions call Regency Ofce Furniture at 1-866-816-9822
(14” x 13” x 1”)
Cam Lock Assembly:
To open Cam, point arrow
toward Cam Pin hole. To
lock Cam, turn clockwise.
Figure 1:
HD-G
HD-D
HD-A
HD-F
HD-E
HD-B
HD-C
HD-H
HD-H: Base
(69” x 14” x 1”)
Quantity: 1
HD-F: Right Side
(15” x 31” x 1”)
Quantity: 1
HD-D: Foot Bracket
(15”D)
Quantity: 2
4-door Hutch
Page 1

STEP 2 : Attach Divider(HD-C) to Base(HD-H) by inserting
and locking cams (Figure 1).
NOTE: Finished side of Divider should face the track side of
the Base.
Hardware :
I: 3” Screw/Washers
(76mm)
Quantity: 4
J: Allen Key
Quantity: 1
L: Handles
Quantity: 4
K: Wood Cam Pins
Quantity: 17
M: Handle Screws
(25mm)
Quantity: 8
N: Double Sided
Tape
Quantity: 1
Any problems or questions call Regency Ofce Furniture at 1-866-816-9822
800-558-1010
www.NBF.com
STEP 1 : Insert 2 Wood Cam Pins(K) into Base(HD-H).
STEP 3 : Insert 1 Wood Cam Pin(K) into Back Panel(HD-A).
K
HD-H
K
HD-C
HD-H
STEP 4 : Attach Divider(HD-C) and Base(HD-H) to Back
Panel(HD-A) by inserting and locking cam (Figure 1).
HD-A
K
HD-A
HD-C
HD-H
O: Cam Covers
Quantity: 17
4-door Hutch • INSTRUCTIONS
CARTONS: HD71
4-door Hutch
Page 2

Any problems or questions call Regency Ofce Furniture at 1-866-816-9822
800-558-1010
www.NBF.com
STEP 5: Insert 4 Wood Cam Pins(K) into the Left Side(HD-E)
and Right Side(HD-F).
STEP 6 : Connect Left Side(HD-E) and Right Side(HD-F) to
the Back Panel(HD-A) and Base(HD-H) by inserting and
locking cams (Figure 1).
HD-E
KK
K
K
HD-F
KK
K
KHD-E HD-F
HD-A
HD-H
STEP 7 : Insert 6 Wood Cam Pins(K) into the Top(HD-G).
6 Wood Cam Pins(K)
into the
Top(HD-G).
STEP 8 : Attach Top(HD-G) to the Left Side(HD-E), Right Side(HD-F), Divider(HD-C) and Back Panel(HD-A) by inserting and
locking cams. (Figure 1).
K
K
K
K
K
K
HD-G
HD-A
HD-E HD-F
HD-C
HD-G
4-door Hutch • INSTRUCTIONS
CARTONS: HD71
4-door Hutch
Page 3

Any problems or questions call Regency Ofce Furniture at 1-866-816-9822
800-558-1010
www.NBF.com
STEP 9 : Attach Foot Bracket(HD-D) to the Left Side(HD-E)
by using 2 Screw/Washers(I). Repeat this step for the Right
Side(HD-F).
HD-D
I
I
HD-E
STEP 10 : Attach 1 Handle(L) to each Sliding Door(HD-B) with
2 Handle Screws(M). Repeat this step for all doors.
HD-B
L
STEP 11 : Insert each Sliding Door(HD-B) by pushing down on the top switch of the door and placing the bottom into the track on
the Base(HD-H). Once in the track, release the top switch to lock in place. Repeat this step for all Doors.
STEP 12 : To nish installation, place Cam Covers(O)
where needed.
STEP 13 : For additional stability, use the Double Sided Tape(N) to
adhere the Foot Brackets(HD-D) of the Hutch to the Desk that you are
placing it on.
4-door Hutch • INSTRUCTIONS
CARTONS: HD71
4-door Hutch
Page 4