NC-link NC-AP233(P) User manual

User Manual of NC-AP233(P)/NC-AP231
Version V1.0

1
www.nc-link.cn
Thank you for purchasing NC-Link In-Wall Access Point. This manual will instruct
you how to configure and the AP, enable you to use it in a perfect status.
Please check the Package before use it.
Package Contents
Item
Description
Unit
QTY
1
Access Point
PCS
1
2
Mounting Accessory
Set
1
3
Quick Installation Guide
PC
1
1. Manual Instruction
This manual is subject to tell users how to use this Wireless Access Point
properly. Contents include description of this platform’s properties, and how to
configure this platform. Pre-reading this manual before operation is highly
recommended.
1.1 Target Reader
This manual is for those familiar with basic networking knowledge and
terminology
2. Product Introduction
NC-AP233P/NC-AP233/NC-AP231 are highly performance In-Wall Access Point
with internal antennas, complied with IEEE 802.11n/g/b. They can support up to
10-15 clients, suitable for hotel guest room and small meeting room etc.
NC-AP224 is 300Mbps @2.4GHz
2.1 Product Layout
2.1.1 Interface
Reset: Press the Reset button about 15 seconds, then release to reset
LAN: Then LAN port is used for bridging
USB Charger: The USB Charger can provide 5V/1A output charge

2
www.nc-link.cn
Power Button: To power ON/OFF of the device
The default IP address is 192.168.188.253
Default user name & password are admin
RJ45 Connector
NC-AP233P with 1 x 10/100Mbps auto-negotiation RJ45 LAN Port
NC-AP233 with 1 x 10/100Mbps auto-negotiation RJ45 LAN Port
NC-AP231 with 1 x 10/100Mbps auto-negotiation RJ45 LAN Port
WAN: The WAN port is used to connect to the power and Internet
NC-AP233P with 1 x 10/100Mbps auto-negotiation RJ45 WAN Port
NC-AP233 with 1 x 10/100Mbps auto-negotiation RJ45 WAN Port
NC-AP231 with 1 x 10/100Mbps auto-negotiation RJ45 WAN Port
3. Login
Connect your PC to the In-Wall Access Point’s LAN Port, then login Web
Management Page with default IP Address: http://192.168.188.253
Default username & password: admin. Below base on Chrome browser.
Note:
Before login the Web Management Page, configure your PC with a fixed IP
address, 192.168.188.X (X between 2 to 252) since default mode is AP
Mode.
Login Steps:
Open Chrome browser, input http://192.168.188.253 in the address bar to login
Access Point
Input the default user name & password: admin, then click “Log In”

3
www.nc-link.cn
After login, you can see below Web page.
Default operating mode is AP Mode.

4
www.nc-link.cn
4. Repeater Mode Configuration
a) In Wireless Repeater, click “Scan AP”
b) Select the AP signal you want to repeat

5
www.nc-link.cn
c) Fill in the Password of the repeated signal and set AP’s wireless parameters.
d) Click “Apply”to complete the configuration

6
www.nc-link.cn
e) Configuration completed, device will reboot
5. AP Mode Configuration
a) Select “Wireless Coverage”

7
www.nc-link.cn
b) Set the parameter SSID, Authentication and Password
c) Click “Apply”then click “OK”to complete setting

8
www.nc-link.cn
d) Configuration completed, device will reboot
6. Gateway Mode Configuration
Dynamic IP
a) Click “Internet Setting”
b) If Internet to LAN Port is Dynamic IP, only need to fill in the wireless
parameters. Like SSID, Authentication, Password

9
www.nc-link.cn
c) Then “Apply”and click “OK”to complete the configuration.