Necta KORO PRIME ES User manual

KORO PRIME ES
U4875DE00 10-2016
Warnings * some models only.
"ON / OFF" switch
D isplay
K EybOarD
l OcK
D OOr
l iqUiD wastE tray
s OliD wastE tray
w atEr taNK *
G
riD
F
lOat
U
ppEr paNEl
D EcaFF chUtE *
D
EcaFF Flap *
i
NstaNt prODUct caNistEr cOvEr
i NstaNt prODUct caNistEr
c OFFEE bEaNs caNistEr
M ixEr
N OzzlE sUppOrt
b rEw UNit

KORO PRIME ES
clEaNiNG aND FilliNG
Load products:
• Open the vending machine door.
• Lift the upper panel and open the covers of the canisters.
• Load the instant product without compressing powder.
• Load the coffee beans.
Fill the tank (models with tank only)
• Remove the liquid waste tray.
• Remove the tank (A) by pulling the handle.
• Empty the residual water from the tank and sanitise the tank
• Fill in the tank with drinkable water up to the max level (B).
• Re-position the tank and the liquid waste tray
Empty the liquid waste tray
When the float emerges from the grid, promptly empty the liquid
waste tray.
It is advisable not to wait for the float signal, but to empty the tray at
regular intervals.
Empty the solid waste tray
• Take the tray (A) by its sides, lift it slightly and pull.
• Empty the tray and wash it with a neutral detergent solution.
Empty the solid waste tray
• Take the liquid waste tray by its sides, lift it slightly and pull.
• Remove the solid waste tray
• Empty the tray and wash it with a detergent solution.
• Re-position the trays
Rinse the mixer
• Hold the last key down for 3 seconds
• Enter the mixer rinse password
Rinse the mixer every day and whenever you load products
Make sure that the products to be loaded have been
properly preserved and they are not past their sell-by
date
A
A
B
2
2
3
1
1
1
N OtE thE MixEr
washiNG passwOrD
MAX
WASTE
CONT. FULL
0
1
2
3
4
5
6
7

KORO PRIME ES
AA
A
CC
C
BB
B
Disassemble the mixer
• Detach the tube from the mixer.
• Turn the product dispensing port (A) upwards to facilitate the oper-
ation.
• Turn the lever (C) counterclockwise.
• Take the mixer unit (B) and pull.
• Detach all components: product funnel (A), powder deposit drawer
(B), water funnel (C).
• Disassemble the mixer impeller
• Use a finger to hold the toothed disk mounted on the whipper
motor firm and unscrew the mixer impeller.
• Wash and rinse all disassembled parts carefully.
• Re-assemble the impeller.
MixEr clEaNiNG
Assemble the mixer:
• Re-assemble all mixer components (B).
• Turn the lever (C) clockwise to secure the mixer.
• Turn the port A) of the instant product downwards
• Re-connect the tube with the mixer.
B
D
A
C
Clean the nozzles:
• Detach the tubes (A) from the nozzles.
• Press the button to release the nozzle support (B).
• Detach the nozzles (D) from the support (C).
• Wash and dry all the parts carefully.
B
A
Nozzle support assembly:
• Insert the nozzle support (A) into the guide (B) and push until
you hear a click.
• Re-insert the nozzles in the support and re-connect the tubes
with the relative nozzles.
2
4
6
1
3
5

KORO PRIME ES
N&W GLOBAL VENDING S.p.A. - Via Roma, 24 - 24030 Valbrembo (BG) Italy - Tel. [phone] - Web: www.nwglobalvending.com
Instant canister:
• Open the vending machine door and lift the upper panel.
• Push slightly inside and lift the canister.
• Remove the canister from the machine
• Dust the canister and the base carefully.
• Re-position the canister into its seat.
A
B
C
D
Cleaning the brew unit:
• Unscrew the ring nut (A) and pay attention not to lose the gasket.
• Remove the coffee waste conveyor (B), if any.
• Unscrew the pin (C).
• Remove the brew unit (D).
Cleaning the brew unit
• Whenever you load or at least every week, it is recommended to
remove any coffee residual from around the brew unit.
• Rinse the brew unit beneath a water jet.
• Rinse the unit carefully.
• Re-assemble the unit by carrying out the operations in the reverse
order.
Clean inside the machine with a neutral detergent solution by using a
piece of cloth that is slightly wet.
Never use any water jet.
To avoid any risk of chemical oxidation or corrosion
in general, use neutral detergents and avoid any sol-
vent.
2
4
1
3
cOMplEtE clEaNiNG