Necta KORO FRESH-BREW User manual

KORO FRESH-BREW
Below there are some simple instructions
for loading and cleaning your machine. WARNING Operations to do with the machine turned ON.
ON
07-2007 U253U01
P OWER ON /P
OWER OFF SWITCH
D
ISPLAY
S
ELECTIONS BUTTONS
D OOR LOCK
M ACHINE DOOR
L IQUID WASTE TRAY
L ID AND LOCK
W ATER TANK
N
OZZLE FOR JUG
S
OLID WASTE TRAY
G RILLE
D RIP TRAY FULL INDICATORS
L
ID
I
NSTANT POWDER CONTAINER LID
I NSTANT POWDER CONTAINER
F RESH PRODUCT CONTAINER
M
IXING BOWL
S POUT HOLDER
F
RESH - BREWER UNIT

L
OADING
R
EGULAR CLEANING
R
EGULAR CLEANING
C LEANING / L OADING
1 2
Loading products:
• Open the dispenser door.
• Lift the dispenser lid and open the lids of the containers to be
loaded.
• Load the products, taking care not to compact the powder.
Filling up the water supply tank:
• Extract the handle and lift it.
• Remove the water tank by pulling on the special handle.
• Use the key for opening the tank’s lid.
• Rinse and fill the tank with drinking water up to the maximum level (A).
• Fit the tank back into place.
• If necessary, empty the liquid waste tray.
1 2
Emptying the liquid waste tray:
When the red float signal lifts up through the grille, it is necessary to
empty the liquid waste tray immediately.
It is advisable not to wait until the red drip tray full indicator is
visible. It is recommended that the liquid waste tray is emptied
regularly.
Emptying the liquid waste tray:
• Take hold of the sides of the trays.
• Lightly lift and pull.
• Remove the grilles by taking hold of the special side holes.
• Empty and wash the trays.
3 4
Emptying the solid waste tray:
When the “W
ASTE TRAY FULL ” message appears on the display, the
solid and liquid waste trays require emptying.
• Take hold of the sides of the liquid waste trays firmly. Lift and pull.
• Remove the solid waste tray (A) and empty it.
• Fit both trays back into position.
Rinsing the mixer:
• With the door closed, press and hold the last selection button for
3 seconds.
• When “Password” appears on the display.
Enter 5 digit password for rinse function.
The mixer rinsing cycle must be carried out regularly or after
loading the instant powder.
KORO FRESH-BREW
ON
A
ONON
ON
1
A
ON
W ASTE
TRAY FULL

D EEP CLEANING
1 2
Removing and sanitising the mixer:
• Detach tube (D) from mixer.
• Rotate the product dispensing nozzle (A) upwards.
• Rotate the lever (C) anticlockwise.
• Take hold of the mixer assembly (B) firmly, and pull.
Removing and sanitising the mixer:
• Separate all the mixer assembly components: product funnel (A),
powder deposit drawer (B), mixing bowl (C).
3 4
Removing and sanitising the mixer:
• To remove mixer impellers, use a finger to hold the cogged disk
fitted on the mixer shaft below the mixer chamber.
• Unscrew the impeller.
• Thoroughly wash, rinse and dry all of the removed components.
• Reassemble the impeller.
Reassemble the mixer:
• Reassemble all the mixer (B) components.
• Rotate the lever ring (C) clockwise to lock the mixer onto the dis-
penser.
• Rotate the product dispensing nozzle (A) back down again.
• Connect the tube (D) to the mixing bowl.
5 6
Cleaning the dispensing spouts:
• Detach the tubes (A) from the dispensing spouts.
• Press pushbutton (B) to release the dispensing spouts carrier
plate (C).
• Detach the dispensing spouts (D) from spout holder (C).
Cleaning the dispensing spout:
• Separate the three parts that compose the dispensing spout (E).
• Thoroughly wash and dry all the removed components.
KORO FRESH-BREW
A
B
C
D
A
B
E
C
D
A
B
C
B
D
A
C
2

D EEP CLEANING
7 8
Reassembling the dispensing spouts:
• Insert the dispensing spout holder (A) into guide (B) and press
until it clicks.
• Reassemble the parts of the dispensing spout.
• Reinsert the dispensing spout onto the spout holder (A).
• Reinsert the dispensing spouts for the instant drinks onto the
spout holder (A).
• Connect the tubes onto their dispensing spouts.
Cleaning the containers:
• Open the dispenser door and lift the lid.
• Lightly push back and lift the containers.
• Remove the containers from the dispenser.
• Brush the containers, removing all instant powder residue.
910
Internal dispenser cleaning:
• Clean the inside of the dispenser using a mild detergent solution
and a lightly damp cloth.
KORO FRESH-BREW
3
B
A
U
SE MILD DETERGENTS FOR CLEANING .
D
O NOT USE SOLVENTS OR SCENTED
CLEANING PRODUCTS
.
I N ORDER TO KEEP THE CHARACTERISTICS OF THE
DISPENSED DRINK UNALTERED IT IS NECESSARY
TO CLEAN THE BREWER UNIT AT LEAST WEEKLY
.
T
HE COMPONENTS CAN BE WASHED IN A DISHWASHER AT
A MAXIMUM TEMPERATURE OF
60°C.
U PPER LID
C ONVEYOR
U PPER VALVE
P UMPING CHAMBER
B REWING CHAMBER
F ILTER
F ILTER SUPPORT
F ILTER HOLDER
B
RUSH

R EMOVING THE BREWER UNIT
1 2
• Press the two jaws of the brewer unit.
• Pull the brewing chamber to extract it.
• Release the two clips (A) from the upper lid.
3 4
• Remove the upper lid. • Take hold of the brewing chamber firmly.
• Rotate the conveyor clockwise.
5 6
• Remove the conveyor. • Remove the upper valve.
KORO FRESH-BREW
4
A

R EMOVING THE BREWER UNIT
7 8
• Lift the filter cleaning brush to remove it.
• Remove any coffee grounds residue from the brush.
• Press the filter levers (A) and at the same time pull the filter hol-
der until completely extracted.
910
• Separate the filter (A) from the filter holder (B).
• Check the state of wear of the components.
Replace the filter if damaged and/or encrusted.
• Remove the powder exhaust drawer.
11 12
• Take hold of the pumping chamber.
• Lift it lightly and pull.
• Completely extract the pumping chamber.
• Thoroughly wash the removed components.
• Thoroughly rinse and dry the components, then reassemble the
brewer unit.
The components can be washed in a dishwasher at a maxi-
mum temperature of 60°C.
KORO FRESH-BREW
5
A
B
A

I NSTALLING THE BREWER UNIT
1 2
• Fit the upper valve back onto the brewing chamber. • Fit the conveyor onto the brewing chamber.
3 4
• Take hold of the brewing chamber firmly.
• Rotate the conveyor onto the brewing chamber clockwise.
• Fit the upper lid onto the conveyor.
• Secure it with its clips.
5 6
• Brewer unit correctly installed. • Fit the pumping chamber back into position.
KORO FRESH-BREW
6

I NSTALLING THE BREWER UNIT
7 8
• Push the pumping chamber until inserted completely. • Fit the powder exhaust drawer back into position.
KORO FRESH-BREW
7
910
• Before reinstalling the filter, check the conditions of the filter and
of its support; if damaged and/or encrusted they must be re-
placed.
• Reassemble the filter and its support.
• Insert the filter holder drawer pressing until it clicks.
11 12
• Fit the filter cleaning brush back into position. • Fit the brewer unit back into place.
• Connect the water tube (A) to the conveyor.
A
N&W GLOBAL VENDING S.p.A. - Via Roma, 24 - 24030 Valbrembo (BG) Italy - Tel. [phone] - Web: www.nwglobalvending.com