Nera WorldCommunicator User manual

MENU
>Start Search
Lock terminal
52 0 05:46
USB
RS-232
IS N
MODEM UNIT
ANTENNA
Antenna cable
IS N telephone
Free line of sight
to the satellite
1 2 3
4 5 6
7 8 9
0 #
P S Re
ECT handset
Compass
Storm lock
PC
Use AOR-W ?
520 09:46
Searching
All regions
0 09:46
Maximum achieved
signal strength
Signal strength
bar
Signal strength
indication
WorldCommunicator
Phone PIN : 0
0 09:46
Higher digit
Lower digit
Next
digit
After 4th
digit
Setting up
1 Open the WorldCommunicator by swinging
down the Modem Unit.
2 Unfold the antenna. Use storm locks if necessary.
3Press and
hold for
2 secs.
4PIN code:
use multi-
buttons as indicated (default code: 1 2 3 4).
5Check antenna cable connections.
6The four satellites are positioned
stationary above equator, see map in
"Getting Started" or on CD. To find the
correct vertical angle to the satellite,
try with 60°, 30° or 0° as indicated.
7Aim the antenna
towards the esti-
mated position of
the satellite with
free line of sight,
or make a slow scan
across the hemi-
sphere. If necessary, use the compass.
Nera WorldCommunicator - Quickstart
0°
60°
30°
Nera Document no. Rev A
The shaded signal strength bar
appearing in the display increases
in length when closing in on the
satellite.
The signal strength
should be at least 520 for
64 kbps communication.
8 Press to accept
the Ocean Region satellite.
If no spot beam is found from the current
satellite, try another Ocean Region.
○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○

On DE T
also:
Unknown net
AOR-W
Ready for call
520 09:46
Note! Default Net service provider
must be programmed the first
time an Ocean Region is entered:
• Press to open the MENU.
Scroll down to Set Default Net
and press .
• Press at required provider.
When using a SIM card, the Net
service provider is preset.
ISDN telephone:
9 Connect the ISDN telephone and verify that you have a
dial tone. If no MSN number is configured, 4.8 kbps
speech quality is automatically chosen.
Hi gh quality 64 kbps speech service is selected by entering
MSN no.30 into the ISDN equipment (see Getting Started.)
DECT handset registration:
10 Press on the WorldCommunicator to enter the
MENU. Scroll down to Enable DECT and press .
• "Open to register” appears.
• Switch ON the DECT
handset. When the message
Register? appears, press the
YES display key.
• Enter the WorldCommunicator base station pass-
word:1234(the first four digits of the owner pass-
word. Use new code when changed.)
• Press the OK display key.
• Press when REGISTERED appears in the
WorldCommunicator display.
Nera WorldCommunicator - Quickstart CONT’D
○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○
MENU
> Set efault Net.
Configure TE
520 09:46
MENU
> Enable ECT
Self Test
520 09:46
Making a call:
11 Dial 00, country code and subscriber number .
Press to send the number, f.ex.:
0 0 4 7 6 7 2 4 4 7 0 0
Data setup:
Use the Windows dial-up networking to programme
the server telephone number.
Make sure to use the correct modem driver.
Delete IPX/SPX and NetBEUI if TCP/IP is used.
Note! Some Net providers offer free e-mail and
internet access by dialing 28#.
Dialing an ISDN compatible server:
Connect the computer to the ISDN/RS-232 or USB
port. Use the following modem drivers:
• ISDN, use a driver matching your PCMCIA/PCI
card.
• RS-232, use a 28.800 bps driver.
• USB, on computer use the Nera WorldCommunicator
USB modem driver (installed when updating vtLite).
On a Mac computer, use Metric Ricochet Wireless.
Dialing an analogue compatible server:
Use the ISDN port and an analogue modem PCMCIA/
PCI card connected to the computer.
See detailed application notes on the
WorldCommunicator CD.