NetComm 3GM1WN User manual

NETCOMM LIBERTY™ SERIES
3G Wireless N150
Mini Router m1

1. Connect the power to your NetComm m1 by either:
A) Plugging the supplied power adapter into a wall power outlet and then into
to the port labelled “Power” on the side of the NetComm m1.
B) Plugging the supplied USB cable into the port labelled “Power” on the
NetComm m1 and the other end into a compatible USB port on your laptop/
desktop computer.
2. Slide the power switch to the “ON” position and wait for approximately
2 minutes to allow the device to start up.
3. Connect a compatible 3G USB Modem to the “3G USB” port on the NetComm m1.
1
Hardware Installation
USB
Modem
3G Tower
Power Point Power Adapter
Laptop
OR

WiFi PDA
Online Gaming
Laptop
IPad
2
Establishing a WiFi Connection
The NetComm m1 creates a personal WiFi coverage zone to provide Internet
access to WiFi enabled devices.
1. Using your WiFi enabled device, scan for wireless networks in your area and
select the network called “NetComm Wireless”.
2. Enter the following default security key: a1b2c3d4e5
Note: For optimal WiFi security, we recommend changing the default wireless security settings through the web based user interface. For more details,
please consult the User Guide located on the supplied CD.

USB
Modem
3G Tower
WiFi PDA
Laptop
Online Gaming
IPad
3
Connecting to the Internet
After completing the hardware installation, you will need to enter the necessary
settings to be able to connect to your 3G service provider. You can do this via the
product’s web based user interface by following the steps below:
1. On your computer, open a web-browser (such as Internet Explorer, Firefox,
or Safari), type 192.168.1.1 into the address bar at the top of the screen and
press enter.
2. Attheloginscreen,type“admin”intothesystempasswordeldandthenclick
“Login” to continue.
3. Completethesetupwizardbyllinginthedetailsofyour3Gconnection.

These settings are required by the NetComm m1 to connect to your 3G service.
If you don’t know what settings to use here, please contact your 3G service provider
to obtain this information.
4. After completing the wizard, wait for 2 minutes to allow the NetComm m1 to
connect to the internet.
5. If you are connected successfully, the blue 3G light on the top of the unit will be lit.
You can also check on the status of your connection by clicking ”Status” after
logging in to the web based user interface.

Mobile Service Provider APN*
AUSTRALIA
Telstra Telstra.internet
Telstra.pcpack
Telstra.datapack
Telstra.extranet
Optus - Postpaid connect
Optus - Prepaid preconnect
Three - Postpaid 3netaccess
Three - Prepaid 3services
Vodafone - Postpaid vnternet.au
Vodafone - Prepaid vfprepaymbb
Crazy John’s purtona.net
DoDo dodolns1
Blink splns888a1
Internode Internode
Primus primuslns1
TPG internet
Exetel Exetel1
NEW ZEALAND
Vodafone NZ www.vodafone.net.nz
CallPlus www.callplus.net.nz
Slingshot www.slingshot.net.nz
Telstra Clear www.telstraclear.net.nz
Telecomm NZ XT internet.telecomm.co.nz

4
?
Troubleshooting
Ifyouexperiencedifcultiesconnectingtotheinternet,pleaseverifythefollowing:
• CheckthatyourSIMisactiveformobilebroadband.Your3Gserviceprovider
canconrmthis.
• Checkthatyour3GUSBmodemiscompatiblewiththeNetCommm1.
If you are unsure whether your 3G USB Modem is compatible with the NetComm
m1, please refer to the 3G compatibility list on the NetComm website.
• Ensurethatyouhavemobilebroadbandcoverageinyourarea.

You can check whether the NetComm m1 has coverage by looking at the status
page on the Web based User interface.
• Checkthatyour3Gserviceprovider’ssettingshavebeensetcorrectly(APN,
etc.) in the web based user interface.
• Forfurtherassistance,pleasecontactNetCommtechnicalsupportorvisitour
website at www.netcomm.com.au