NETGEAR WGM511 User manual

December 2004
202-10068-01
Version 1.0
December 2004
NETGEAR, Inc.
4500 Great America Parkway
Santa Clara, CA 95054 USA
User Manual for the
NETGEARPre-NWireless
PC Card WGM511

ii
December 2004
Technical Support
Please refer to the support information card that shipped with your product. By registering your
product at http://www.netgear.com/register, we can provide you with faster expert technical
support and timely notices of product and software upgrades.
NETGEAR, INC. Support Information
Phone: 1-888-NETGEAR, for US & Canada only. For other countries, see your Support
information card.
E-mail: [e-mail]
Web site: http://www.netgear.com
Statement of Conditions
In the interest of improving internal design, operational function, and/or reliability, NETGEAR reserves the right to
make changes to the products described in this document without notice.
NETGEAR does not assume any liability that may occur due to the use or application of the product(s) or circuit
layout(s) described herein.
© 2004 NETGEAR, Inc. NETGEAR, the NETGEAR logo, The Gear Guy and Everybody's Connecting are
trademarks or registered trademarks of NETGEAR, Inc. in the United States and/or other countries.
Microsoft and Windows are registered trademarks of Microsoft Corporation in the United States and/or
other countries. Other brand and product names are trademarks or registered trademarks of their respective
holders. Information is subject to change without notice. All rights reserved.
December 2004
Certificate of the Manufacturer/Importer
It is hereby certified that the Model WGM511 Wireless PC Card has been suppressed in accordance with the conditions
set out in the BMPT- AmtsblVfg 243/1991 and Vfg 46/1992. The operation of some equipment (for example, test
transmitters) in accordance with the regulations may, however, be subject to certain restrictions. Please refer to the notes
in the operating instructions.
Federal Office for Telecommunications Approvals has been notified of the placing of this equipment on the market and
has been granted the right to test the series for compliance with the regulations.
FCC Information to User
This product does not contain any user serviceable components and is to be used with approved antennas only. Any
product changes or modifications will invalidate all applicable regulatory certifications and approvals
FCC Guidelines for Human Exposure
In order to comply with RF exposure limits established in the ANSI C95.1 standards, the user is advised to maintain a
distance of at least 1 inch (2.5 cm) from the antenna of this device while it is in use.

December 2004
iii
Declaration Of Conformity
We NETGEAR, Inc., 4500 Great America Parkway, Santa Clara, CA 95054, declare under our sole responsibility that
the model WGM511 Cardbus Card Wireless Adapter complies with Part 15 of FCC Rules. Operation is subject to the
following two conditions:
• This device may not cause harmful interference, and
• This device must accept any interference received, including interference that may cause undesired operation.
Regulatory Compliance Information
This section includes user requirements for operating this product in accordance with National laws for usage of radio
spectrum and operation of radio devices. Failure of the end-user to comply with the applicable requirements may result
in unlawful operation and adverse action against the end-user by the applicable National regulatory authority.
NOTE: This product's firmware limits operation to only the channels allowed in a particular Region or Country.
Therefore, all options described in this user's guide may not be available in your version of the product.
FCC Requirements for Operation in the United States
Radio Frequency Interference Warnings & Instructions
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of
the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential
installation. This equipment uses and can radiate radio frequency energy and, if not installed and used in accordance
with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that
interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to
correct the interference by one or more of the following methods:
• Reorient or relocate the receiving antenna
• Increase the separation between the equipment and the receiver
• Connect the equipment into an electrical outlet on a circuit different from that which the radio receiver is connected
• Consult the dealer or an experienced radio/TV technician for help.
Modifications made to the product, unless expressly approved by NETGEAR, Inc., could void the user's right to operate
the equipment.
Export Restrictions
This product or software contains encryption code which may not be exported or transferred from the US or Canada
without an approved US Department of Commerce export license.
NETGEAR Pre-N Wireless PC Card WGM511
FOR HOME OR OFFICE USE
Tested to Comply
with FCC Standards
FCC ID: SA3-AGN1023PC0200

December 2004
iv

Contents v
December 2004
Contents
Chapter 1
About This Manual
Audience .........................................................................................................................1-1
Scope .............................................................................................................................1-1
Typographical Conventions ............................................................................................1-2
Special Message Formats ..............................................................................................1-2
How to Print this Manual .................................................................................................1-2
Chapter 2
Introduction
About the NETGEAR Pre-N Wireless PC Card WGM511 ..............................................2-1
Key Features and Related NETGEAR Products ............................................................2-1
What’s in the Box? ..........................................................................................................2-2
WGM511 LEDs and Interfaces .......................................................................................2-2
A Road Map for “How to Get There From Here” ............................................................2-3
Chapter 3
Basic Setup
What You Need Before You Begin ..................................................................................3-1
Verifying System Requirements ...............................................................................3-1
Observing Location and Range Guidelines ..............................................................3-2
Two Operating Modes ....................................................................................................3-2
WGM511 Default Wireless Configuration Settings .........................................................3-2
Basic Installation Instructions .........................................................................................3-3
For Windows 2000 Users Installing a WGM511 .......................................................3-6
WGM511 Wireless Connection Indicators ......................................................................3-9
Interpreting the LEDs on the WGM511 ..................................................................3-10
Interpreting System Tray Icon Colors .....................................................................3-10
Chapter 4
NETGEAR Smart Wireless Wizard
Understanding the Configuration Options ......................................................................4-1
Using Configuration Profiles ...........................................................................................4-1
Connecting to an Access Point in Infrastructure Mode ............................................4-2

December 2004
vi Contents
How to Configure an Infrastructure Mode Profile .....................................................4-3
Connecting to Another PC in Ad Hoc Mode ...................................................................4-4
How to Configure an Ad Hoc Mode Profile ..............................................................4-5
How to Start a Computer-to-Computer (Ad Hoc) Network .......................................4-6
Statistics Page ..........................................................................................................4-7
Advanced Settings Display ......................................................................................4-9
Chapter 5
Wireless Security Configuration
Understanding the Security Options ...............................................................................5-1
Using WEP Security .......................................................................................................5-1
Basic Requirements for WEP ...................................................................................5-2
WEP Security Settings Worksheet ...........................................................................5-3
How to Configure WEP Encryption Security ............................................................5-4
Using the Wireless Zero Configuration Service for WPA-PSK Advanced Security ........5-5
Enabling Wireless Security Features ..............................................................................5-6
Identifying the Wireless Network Name (SSID) and WEP Security Settings ...........5-6
How to Configure WEP Encryption Security ............................................................5-7
Chapter 6
Troubleshooting
Troubleshooting Basic Tips ......................................................................................6-1
Frequently Asked Questions ..........................................................................................6-2
Appendix A
Technical Specifications ......................................................................................................A1
Appendix B
Wireless Networking Basics
Wireless Networking Overview ...................................................................................... B-1
Infrastructure Mode ................................................................................................. B-1
Ad Hoc Mode (Peer-to-Peer Workgroup) ................................................................ B-1
Network Name: Extended Service Set Identification (ESSID) ................................ B-2
Wireless Channels .................................................................................................. B-2
WEP Wireless Security .................................................................................................. B-3
WEP Authentication ................................................................................................ B-3
WEP Open System Authentication ......................................................................... B-4
WEP Shared Key Authentication ............................................................................ B-5
How to Use WEP Parameters ................................................................................. B-7
WPA Wireless Security .................................................................................................. B-7

Contents vii
December 2004
How Does WPA Compare to WEP? ........................................................................ B-8
How Does WPA Compare to IEEE 802.11i? .......................................................... B-8
What are the Key Features of WPA Security? ........................................................ B-9
Is WPA Perfect? .................................................................................................... B-14
Product Support for WPA ...................................................................................... B-15
Appendix C
Preparing Your PCs for Network Access
Preparing Your Computers for TCP/IP Networking .......................................................C-1
Configuring Windows 98 and Me for TCP/IP Networking ..............................................C-1
Install or Verify Windows Networking Components .................................................C-1
Enabling DHCP to Automatically Configure TCP/IP Settings in
Windows 98 and Me ................................................................................................C-3
Selecting Windows’ Internet Access Method ..........................................................C-5
Verifying TCP/IP Properties ....................................................................................C-5
Configuring Windows 2000 or XP for TCP/IP Networking .............................................C-6
Install or Verify Windows Networking Components .................................................C-6
DHCP Configuration of TCP/IP in Windows XP or 2000 .........................................C-7
DHCP Configuration of TCP/IP in Windows XP .....................................................C-7
DHCP Configuration of TCP/IP in Windows 2000 ..................................................C-9
Verifying TCP/IP Properties for Windows XP or 2000 ........................................... C-11
Glossary
List of Glossary Terms ...................................................................................................G-1
Index

December 2004
viii Contents

User Manual for the NETGEAR Pre-N Wireless PC Card WGM511
About This Manual 1-1
December 2004
Chapter 1
About This Manual
Congratulations on your purchase of the NETGEAR Pre-N Wireless PC Card WGM511. The
WGM511 provides connection for multiple personal computers to the Internet through an external
broadband access device (such as a cable modem or DSL modem).
Audience
This reference manual assumes that the reader has basic to intermediate computer and Internet
skills. However, basic computer network, Internet, and firewall technology tutorial information is
provided in the Appendices, on the NETGEAR Pre-N Wireless PC Card WGM511 Resource CD,
and on the NETGEAR Web site.
Scope
This manual is written for the WGM511 Pre-N Wireless PC Card according to these
specifications.:
Table 1-1. Manual Specifications
Product Version NETGEAR Pre-N Wireless PC Card WGM511
Manual Publication Date December 2004
Note: Product updates are available on the NETGEAR Web site at
http://www.netgear.com/support/main.asp

User Manual for the NETGEAR Pre-N Wireless PC Card WGM511
1-2 About This Manual
December 2004
Typographical Conventions
This guide uses the following typographical conventions:
Special Message Formats
This guide uses the following formats to highlight special messages:
How to Print this Manual
To print this manual you may choose one of the following several options, according to your
needs.
•A Chapter. Use the “PDF of This Chapter” link at the top right of any page.
– Click “PDF of This Chapter” link at the top right of any page in the chapter you want to
print. A new browser window opens showing the PDF version of the chapter you were
viewing.
– Click the print icon in the upper left of the window.
–Tip: If your printer supports printing two pages on a single sheet of paper, you can save
paper an printer ink by selecting this feature.
•The Full Manual. Use the PDF button in the toolbar at the top right of the browser window.
– Click PDF button. A new browser window opens showing the PDF version of the chapter
you were viewing.
– Click the print icon in the upper left of the window.
–Tip: If your printer supports printing two pages on a single sheet of paper, you can save
paper an printer ink by selecting this feature.
Table 1. Typographical conventions
italics Emphasis.
bold User input.
Note: This format is used to highlight information of importance or special interest.

User Manual for the NETGEAR Pre-N Wireless PC Card WGM511
Introduction 2-1
December 2004
Chapter 2
Introduction
About the NETGEAR Pre-N Wireless PC Card WGM511
This chapter introduces the features, package contents, and a road map of typical applications for
the NETGEAR Pre-N Wireless PC Card WGM511.
The WGM511 gives you ultimate mobility in your office or while you are traveling. It frees you
from traditional Ethernet wiring and helps you create a wireless network for sharing your
broadband Internet access in and around your home. It is designed for notebook computers
running Microsoft®Windows®. It is 32-bit CardBus compatible and works in any available
CardBus slot.
Its auto-sensing capability allows high packet transfer at up to 108 Mbps for maximum throughput
or dynamic range shifting to lower speeds due to distance or operating limitations in an
environment with a lot of electromagnetic interference.
The WGM511 provides reliable, standards-based 802.11b/g wireless connectivity that is protected
with WEP security. It works with Windows 2000 and Windows XP operating systems. When used
with a router such as the NETGEAR WGM124 router with Airgo’s True MIMO technology,
the WGM511 can provide 802.11g standards-based wireless networking at up to 108 Mbps.
Key Features and Related NETGEAR Products
The WGM511 Pre-N Wireless PC Card provides the following features:
• 802.11b and 802.11g standards-based wireless networking.
• Supports roaming between access points when configured in Infrastructure mode.
• Fast 108 Mbps speed for ultra high speed data transfer. Wireless nodes negotiate to operate in
the optimal data transfer rate. In a noisy environment or when the distance between the
wireless nodes is far, the wireless nodes automatically fall back to operate at lower transfer
rates.

User Manual for the NETGEAR Pre-N Wireless PC Card WGM511
2-2 Introduction
December 2004
• High level of data encryption using the 128-bit Shared Key WEP data encryption method. A
lower level of data encryption or no data encryption is available to simplify your network
setup or to improve data transfer rate.
• 802.11g or 802.11b wireless networking.
What’s in the Box?
The product package should contain the following items:
• NETGEAR Pre-N Wireless PC Card WGM511
• Installation Guide for the NETGEAR Pre-N Wireless PC Card WGM511
•NETGEAR Pre-N Wireless PC Card WGM511 Resource CD, including:
— Driver and Configuration Utility Software
— User Manual for the NETGEAR Pre-N Wireless PC Card WGM511
— Animated Network Properties Configuration Tutorial
— PC Networking Tutorial
• Warranty card
• Support information card
If any of the parts are incorrect, missing, or damaged, contact your NETGEAR dealer. Keep the
carton, including the original packing materials, in case you need to return the product for repair.
WGM511 LEDs and Interfaces
The NETGEAR Pre-N Wireless PC Card WGM511 has two LEDs: Link and Act (Activity). The
Activity LED lights up and blinks when the card is active. The Link LED lights when the card is
connected to a wireless network.
The NETGEAR Pre-N Wireless PC Card WGM511 has two interfaces:
• The PCMCIA Type II connector connects to any notebook PC with an available PCMCIA or
CardBus slot.

User Manual for the NETGEAR Pre-N Wireless PC Card WGM511
Introduction 2-3
December 2004
• The wireless interface of the NETGEAR Pre-N Wireless PC Card WGM511 remains outside
of the notebook PC chassis when the wireless PC card is inserted into a notebook. The LED
indicates the wireless link condition and signal quality of the NETGEAR Pre-N Wireless PC
Card WGM511 with another wireless node or the associated access point.
A Road Map for “How to Get There From Here”
The introduction and adoption of any new technology can be a difficult process. Wireless
technology has removed one of the barriers to networking—running wires. It allows more people
to try networking while at the same time exposes them to the inherent complexity of networking.
General networking concepts, setup, and maintenance can be difficult to understand. In addition,
wireless technology adds issues, such as range, interference, signal quality, and security to the
picture.
To help overcome potential barriers to successfully using wireless networks, the table below
identifies how to accomplish such things as connecting to a wireless network, assuring appropriate
security measures are taken, browsing the Internet through your wireless connection, exchanging
files with other computers and using printers in the combined wireless and wired network.
Table 2-1. A Road Map for How to Get There From Here ...
If I Want To ... ? What Do I Do? What’s Needed? How Do I?
Connect to a
wireless
network.
1. Identify the wireless
network name (SSID)
and, if used, the
wireless security
settings.
2. Set up the WGM511
with the settings from
step 1.
1. A wireless network
2. A notebook PC within the
operating range of the
wireless network. For
guidelines about therange
of wireless networks, see
“Observing Location and
Range Guidelines” on
page 3-2.
To set up the WGM511, see
Chapter 3, “Basic Setup” and
follow the instructions
provided.
To learn about wireless
networking technology, see
Appendix B, “Wireless
Networking Basics” for a
general introduction.

User Manual for the NETGEAR Pre-N Wireless PC Card WGM511
2-4 Introduction
December 2004
Protect my
wireless
connection from
snooping,
hacking, or
information
theft.
1. Assure that the
wireless network has
security features
enabled.
2. Configure your
WGM511 with the
security settings of
the wireless network.
3. Use Windows
security features.
1. A wireless network with
authentication and WEP
encryption enabled.
2. Wireless networking
equipment that supports
WEP encryption, such as
the WGM511 and all
NETGEAR wireless
networking products.
To learn about wireless
networking security, see
“WEP Wireless Security” on
page B-3.
To use WEP security features,
see “Statistics Page” on
page 4-7 and configure your
WGM511 accordingly.
Note: Secure Internet sites such as banks and online merchants use encryption security built into browsers
like Internet Explorer and Netscape. Any wireless networking security features you might implement are in
addition to those already in place on secure Internet sites.
Connect to the
Internet over my
wireless
network.
1. Activateyour wireless
link and verify your
network connection.
2. Open an Internet
browser such as
Internet Explorer or
Netscape Navigator.
1. An active Internet
connection like those from
cable or DSL service
providers.
2. A wireless network
connected to the cable or
DSL Internet service
through a cable/DSL
router as illustrated in
“Connecting to an Access
Point in Infrastructure
Mode” on page 4-2.
3. TCP/IP Internet
networking software
installed and configured
on your notebook PC
according to the
requirements of the
Internet service provider.
4. A browser like Internet
Explorer or Netscape
Navigator.
To configure your WGM511 in
Infrastructure mode, see
“Basic Installation
Instructions” on page 3-3, and
locate the section for your
version of Windows.
For assistance with
configuring the TCP/IP
Internet software on a PC,
see “Preparing Your
Computers for TCP/IP
Networking” on page C-1 or
refer to the PC Networking
Tutorial on the NETGEAR
Pre-N Wireless PC Card
WGM511 Resource CD and
the Help information provided
in the Windows system you
are using.
Table 2-1. A Road Map for How to Get There From Here ...
If I Want To ... ? What Do I Do? What’s Needed? How Do I?

User Manual for the NETGEAR Pre-N Wireless PC Card WGM511
Introduction 2-5
December 2004
Exchange files
between a
wirelessly
connected
notebook
computer and
othercomputers
in a my
combined
wireless and
wired network.
1. Use the Windows
Network
Neighborhoodfeature
to browse for
computers in the
combined wireless
and wired network.
2. Browse the hard drive
ofthetargetcomputer
in the network in
order to locate the
directory or files you
want to work with.
3. Use the Windows
Explorer copy and
paste functions to
exchange files
between the
computers.
1. The notebook computer
you are using to connect
to the wireless network
needs to be configured
with the Windows Client
and File and Print Sharing.
2. The notebook computer
you are using to connect
to the wireless network
needs to be configured
with the same Windows
Workgroup or Domain
settings as the other
Windows computers in the
combined wireless and
wired network.
3. Any Windows networking
security access rights
such as login user name/
password that have been
assigned in the Windows
network or for sharing
particular files must be
provided when Windows
prompts for such
information.
4. If so-called Windows
“peer” Workgroup
networking is being used,
the drive, file system
directory, or file need to be
enabled for sharing.
For assistance with Windows
networking software, see
Appendix , “Preparing Your
Computers for TCP/IP
Networking” for configuration
scenarios or refer to the Help
system included with your
version of Windows.
Windows Domain settings are
usuallymanaged by corporate
computer support groups.
Windows Workgroup settings
are commonly managed by
individuals who want to set up
smallnetworksin their homes,
or small offices.
For assistance with setting up
Windows networking, refer to
the PC Networking Tutorial on
the NETGEAR Pre-N
Wireless PC Card WGM511
Resource CD and the Help
information provided in the
Windows system you are
using.
Table 2-1. A Road Map for How to Get There From Here ...
If I Want To ... ? What Do I Do? What’s Needed? How Do I?

User Manual for the NETGEAR Pre-N Wireless PC Card WGM511
2-6 Introduction
December 2004
Use printers in a
combined
wireless and
wired network.
1. Use the Windows
Printers and Fax
features to locate
available printers in
the combined
wireless and wired
network.
2. Use the Windows
Add a Printer wizard
to add access to a
network printer from
the notebook PC you
are using to
wirelessly connect to
the network.
3. From the File menu of
an application such
as Microsoft Word,
use the Print Setup
feature to direct your
print output to the
printer in the network.
1. The notebook computer
you are using to connect
to the wireless network
needs to be configured
with the Windows Client
and File and Print Sharing.
2. The notebook computer
you are using to connect
to the wireless network
needs to be configured
with the same Windows
Workgroup or Domain
settings as the other
Windows computers in the
combined wireless and
wired network.
3. Any Windows networking
security access rights
such as login user name/
password that have been
assigned in the Windows
network must be provided
when Windows prompts
for such information.
4. If so-called Windows
“peer” networking is being
used, the printer needs to
be enabled for sharing.
Windows Domain settings are
usuallymanaged by corporate
computer support groups.
Windows Workgroup settings
are commonly managed by
individuals who want to set up
smallnetworksin their homes,
or small offices.
For assistance with setting up
Windows networking, refer to
the PC Networking Tutorial on
the NETGEAR Pre-N
Wireless PC Card WGM511
Resource CD and the Help
information provided in the
Windows system you are
using.
For assistance with setting up
printers in Windows, refer to
the Help and Support
information that comes with
the version of the Windows
operating systems you are
using.
Table 2-1. A Road Map for How to Get There From Here ...
If I Want To ... ? What Do I Do? What’s Needed? How Do I?

Basic Setup 3-1
December 2004
Chapter 3
Basic Setup
This chapter describes how to install your NETGEAR Pre-N Wireless PC Card WGM511 and set
up basic wireless connectivity on your Wireless Local Area Network (WLAN). Advanced wireless
network configuration is covered in Chapter 4, “NETGEAR Smart Wireless Wizard” in this
manual.
What You Need Before You Begin
You need to verify that your computer meets the minimum system requirements and identify the
wireless network configuration settings of the WLAN where you will connect before you can
configure your wireless PC card and connect.
Verifying System Requirements
Before installing the NETGEAR Pre-N Wireless PC Card WGM511, please make sure that these
minimum requirements have been met:
• You must have a computer with a Pentium®300 MHz or higher compatible processor with an
available Cardbus slot.
•ACDdrive.
• 5 Mbytes of free hard disk space.
• Windows XP Home, Windows XP Professional, or Windows 2000
• Some versions of Windows may ask for the original Windows operating system installation
files to complete the installation of the WGM511 driver software.
Note: Indoors, computers can easily connect to 802.11 wireless networks at distances of
several hundred feet. Because walls do not always block wireless signals, others outside
your immediate area could access your network. It is important to take appropriate steps
to secure your network from unauthorized access. The NETGEAR Pre-N Wireless PC
Card WGM511 provides highly effective security features, which are covered in
“Statistics Page” on page 4-7 in this manual. Deploy the security features appropriate to
your needs.

User Manual for the NETGEAR Pre-N Wireless PC Card WGM511
3-2 Basic Setup
December 2004
Observing Location and Range Guidelines
Computers can connect over wireless networks indoors at a range which varies significantly based
on the physical location of the computer with the NETGEAR Pre-N Wireless PC Card WGM511.
For best results, avoid potential sources of interference, such as:
• Large metal surfaces
•Microwaves
• 2.4 GHz Cordless phones
In general, wireless devices can communicate through walls. However, if the walls are constructed
with concrete, or have metal, or metal mesh, the effective range will decrease if such materials are
between the devices.
Two Operating Modes
The WGM511 Pre-N Wireless PC Card can operate in the following two modes:
•Infrastructure Mode:An 802.11 networking framework in which devices and computers
communicate with each other by first going through an access point (AP). For example, this
mode is used when computers in a house connect to an access point that is attached to a router
that lets multiple computers share a single cable or DSL broadband Internet connection.
•Ad Hoc Mode:An 802.11 networking framework in which devices or computers
communicate directly with each other, without the use of an AP. For example, Ad Hoc mode is
used when two Windows computers are configured with file and print sharing enabled and you
want to exchange files directly between them.
Both of these configuration options are available with the WGM511 Pre-N Wireless PC Card.
Infrastructure configuration procedures for basic network connectivity are covered below.
Advanced infrastructure configuration procedures and ad hoc configuration are covered in Chapter
4, “NETGEAR Smart Wireless Wizard” of this manual.
WGM511 Default Wireless Configuration Settings
If this is a new wireless network installation, use the factory default settings to set up the network
and verify wireless connectivity. If this is an addition to an existing wireless network, you will
need to identify the wireless configuration and security parameters already defined.
Your NETGEAR Pre-N Wireless PC Card WGM511 factory default basic settings are:

User Manual for the NETGEAR Pre-N Wireless PC Card WGM511
Basic Setup 3-3
December 2004
• Network Name Service Set Identification (SSID): Any (First available network)
Note: In order for the WGM511 Pre-N Wireless PC Card to communicate with a wireless
access point or wireless adapter, all devices must be configured with the same wireless
network name (SSID).
• Network mode (Infrastructure or Ad Hoc): Infrastructure
• Data security WEP encryption: Disabled
The section below provides instructions for setting up the NETGEAR Pre-N Wireless PC Card
WGM511 for basic wireless connectivity to an access point. The procedures below provide
step-by-step installation instructions for Windows PCs. Use the procedure that corresponds to the
version of Windows you are using.
Basic Installation Instructions
Basic instructions for Windows XP Users and for Windows 2000 users are included. Use the
procedure below that corresponds to the version of Windows that you use.
For Windows XP Users Installing a WGM511
Install the WGM511 software.
Note: During installation the following Windows messages may appear:
• Windows Logo testing warning: Click Continue Anyway.
• Update Drivers warning: Click Yes to proceed.
a. Power on your computer, let the operating system boot up completely, and log in as
needed.

User Manual for the NETGEAR Pre-N Wireless PC Card WGM511
3-4 Basic Setup
December 2004
b. Insert the Resource CD for the WGM511
into your CD drive. The Resource CD main
page loads.
Note: If the Resource CD main page does
not automatically load, browse to the CD
and double-click on autorun.exe.
c. Click the Install Driver & Utility link.
The NETGEAR Smart Wizard opens.
d. Follow the Smart Wizard steps, and click
Finish when done.
Install the NETGEAR Pre-N Wireless PC Card WGM511.
a. Hold the WGM511 with the NETGEAR logo facing up and insert it into a CardBus slot in
your computer.
After a short delay the Found New
Hardware Wizard displays.
Found New Hardware Wizard
b. Select Install the software automatically
(Recommended) and click Next.
You will be prompted to enable the
NETGEAR Smart Wizard Wireless
Assistant.
c. Click Yes to accept this option.
If you choose No, you must read the
Windows XP documentation to learn how to
use hte Windows XP wireless network
configuration utillity.
d. Click Finish to complete the installation. You will see the WGM511 system tray icon on
the lower right part of the Windows task bar.
Resource CD main page