NETGEAR Home Router User manual

jË-ÖÍjÁ
.jÍÖ¬ËÖaj
Getting Started
The NETGEAR Smart Wizard Setup CD provides a
graphical step-by-step wizard that will assist you with
setting up your router.
Estimated completion time: about 20 minutes.
What do I do?
Simply put the Smart Wizard CD into your computer,
and follow the on screen instructions.
What’s on the CD?
The Smart Wizard Setup CD contains:
• A setup wizard
• A Setup Manual for your reference
•Tutorials
• Links to useful Web sites
• Bonus items
After the router is set up, how can
I change its configuration?
Simply open a browser and log in to the router at
http://www.routerlogin.net. The user name is admin
and the password is password, in lower case letters.
Remove the NETGEAR Smart Wizard Setup CD. Remove the router.
If you plan to stand the router up, attach its feet.
Become acquainted with the router status lights.
A. First, be sure your Internet connection is
active. Do not plug the router in yet.
B. Insert the NETGEAR Smart Wizard
Setup CD into your computer.
If the wizard screen does not appear, double
click autorun.exe on the CD. Apple Macintosh
users, double click setup.htm on the CD.
C. Next, click Setup.
Simply follow the on-screen instructions to set
up the router. When the setup is finished, go on
line to test your Internet connection.
3RZHU ,QWHUQHW /$1
7HVW
12
3
4

August 2004
©2004 by NETGEAR, Inc. All rights reserved.
NETGEAR is a registered trademark of NETGEAR, Inc. in the
United States and/or other countries.
Other brand and product names are trademarks or registered
trademarks of their respective holders. Information is subject to
change without notice.
I am an advanced user, can I
bypass the setup wizard?
To bypass the wizards, connect the router, log in from
a DHCP enabled (IP & DNS) computer at
http://www.routerlogin.net/basicsetting.htm with
the user name of admin and the password of
password, both in lower case letters.
Troubleshooting Tips
Here are some tips for correcting simple problems
you may have.
Once the router is connected, always
restart your network in this sequence:
1. Unplug and turn off the modem, turn off the
router, and shut down the computer.
2. Turn on the modem and wait two minutes.
3. Turn on the router and wait 1 minute.
4. Turn on the computer.
Make sure the cables are plugged in.
• The router Internet status light will be lit if the
Ethernet cable from the router to the modem is
plugged in securely and the modem and router
are turned on.
• For each powered on computer connected to the
router with an Ethernet cable, the corresponding
LAN status light will be lit. The label on the
bottom of the router identifies the number of each
LAN port.
Make sure the network settings of the
computer are correct.
Computers connected to the router must be configured
to obtain IP and DNS addresses automatically via
DHCP. For help with this, please see the tutorials on
the CD.
Check the router status lights to verify
correct router operation.
The Power light should turn solid green. If after 2
minutes it is not, reset the router as described in the
Setup Manual on the CD.
I don’t have a working CD drive.
Go to http://www.NETGEAR.com and download the
manual for your product from the support area of the
Web site. Follow the setup instructions in the manual.
Technical Support
Thank you for selecting NETGEAR products.
After completing the Smart Wizard configuration
assistant, locate the serial number on the bottom label
of your product and use it to register your product at
http://www.NETGEAR.com/register.
Registration on the web site or over the phone is
required before you can use our telephone support
service. The phone numbers for worldwide regional
customer support centers are on the Warranty and
Support Information card that came with your
product.
Go to http://kbserver.netgear.com for product
updates and web support.