NetSuite SB-085 User manual

Installation and Operating Instructions
PI_SB-085/XX_Rev 01
Doc M shower seat with legs
Doc M shower seat with legs SB-085
Available colours:
DARK BLUE (DB). GREY (GY). BLACK (BL).
Congratulations on the purchase of your wall mounted folding shower seat. This Doc M shower seat has
been designed for use in public building facilities to give users extra support in the shower. It provides
support and assists with the independent sitting of persons while washing, regardless of physical ability.
Warnings:
•On receiving delivery of this product, a thorough
check must be carried out and any defects
immediately reported. The product must be stored
in a dry place and not stacked under other
equipment.
•Installation must be carried out by a qualified
tradesman using suitable fixings for the wall
substrate.
•Non corrosive fixings should be used to fit this
product.
•The wall on which the shower seat is installed must
be flat and capable of taking the load.
•Improper installation/use can cause accidents and
injuries.
•The arm rests are designed for user comfort and
support in a seated position - they are not load
bearing.
•After installation a functional test must be carried
out prior to use.
• Ensure no part of the body is under the seat before
folding it down.
• Do not use the shower seat for any purpose other
than that for which it was designed.
•To maintain the integrity and functionality of this
product, regular cleaning and inspection is necessary.
• These instructions should be retained by the user of
the product for its whole life.
Doc M shower seats with legs, black pads and polished frame SB-085/BL

PI_SB-085/XX_Rev 01
Installation and Operating Instructions
Installation:
Installation should be carried out by a suitably qualified
tradesman using correct fixings for the floor substrate.
Fixings are not supplied with this product to allow the
correct fixing method to be selected per installation.
Consult a fixing manufacturer if unsure of which type of
fixings to use.
1. Once the correct wall fixings have been selected, 6x 6mm
fixings should be used. Seats with a backrest have 1 x
extra seat 6mm diameter hole at the top centre of the
backrest frame. The backrest will need to be slid up and
unclipped off the frame to excess this fixing hole.
2. Offer seat up to the wall at the height required and
adjust the leg heights so that the seat is horizontal. Check
the seat is level and both legs are at the same e-clip
height adjustment. Fine levelling adjustment can be
made using the threaded foot.
3. Mark the fixing hole locations.
4. Drill holes in the wall of a diameter and depth
recommended by supplier of wall fixings. Make sure the
legs are in a vertical position before fixing the seat into
position.
5. Always carry out a functional test after installation and
report any issues immediately.
6. Please leave these instructions with the user.
Using this product:
ALWAYS check the seat is fitted securely to the wall and shows no signs of wear or damage prior to use. The seat folds down
from the wall by gently pulling out the leg frame before pulling the top of the seat to lower to horizontal position (as per frame
label instruction). To fold the seat up against the wall, carefully lift the seat up towards the wall until it reaches the vertical posi-
tion back against the wall or backrest. To ensure the seat stays in the vertical position when not in use, push the leg frame cross
bar back as far as possible. Please keep these instructions in a safe place for future use. These instructions are available in braille
if required.
Cleaning and maintenance:
This shower seat must be checked regularly by a qualified personnel to ensure that it is in perfect working order. This shower
seat can be cleaned using only a very mild detergent. Do not use acidic, alkaline, chlorine based or abrasive cleaning materials.
If the seat has a pad it is recommended that this is removed regularly for thorough cleaning.
Disclaimer:
Nymas pursues a policy of continuing improvement in design and performance of its products and so reserves the right to
change specifications without prior notice. The information contained on this document was correct at date of issue and
dimensions are provided as a guide only. Some variation may occur due to manufacturing tolerances.
We accept no liability whatsoever for personal injury or damage to property that is or has been caused due to incorrect
assembly, installation, or use of this product. Failure to install / use this product in line with these instructions will invalidate any
warranty and may affect product safety.
Packaging:
This post is supplied in plastic wrapping and cardboard carton to keep the product unsoiled until installation. Both are suitable
for recycling operations and should be disposed of in accordance with local recycling regulations.
Warranty:
The standard of manufacture and quality control allows Nymas to offer warranties on all products. The W symbol denotes the
number of years covered if different to the standard 1 year warranty. Where L appears this means the product is guaranteed for
life (terms and conditions apply).