fantastic furniture MEMPHIS User manual

ver3.6
Lowline 1400mm

Page 2
2
3
56
Read Instructions carefully.
Lay out all of the components on a soft surface
as if you were preparing to do a jigsaw puzzle.
Carefully identify each component, especially
those that are similar. The most common mistake
is getting things back to front.
Separate and identify each component from the
hardware pack and rest each one in its proper
W
A
R
N
N
G
WARNING
Check no parts are missing.
4
fully tighten screws（leave slightly
loose.When the item is fully assembled
tighten the screws - but do not over tighten.
FAILURE TO FOLLOW THESE BASIC STEPS CAN LEAD TO DAMAGE
THAT IS NOT COVERED BY YOUR WARRANTY
If glue is required DO NOT set until you are
certain that the parts belong together.

(tools not provided)
Phillips Head Srewdriver
Flat Head Screwdriver
Mallet
What You Need
Page 3
1 x Socket Wrench
Long Base Panel
(P1)
Drawer Top Panel
(P5)
Panel Glass Divider
(P6)
2x
Side Panels
(P3)
12 x Dome Head
Screws
(H1)
13 x Small Cam
Nut and Bolts
(H2)
8 x Big Cam
Nut and Bolts
(H3)
10 x Wooden
Dowels
(H4)
10 x Short
Timber Screws
(H5)
2 x Drawer
Runner Track
(H6)
4 x Glass Clamps
(H7)
1 x Short
Threaded Rod
(H8)
1 x Long
Threaded Rod
(H9)
1 x Stainless
Steel Tube
(H10)
1 x Tube
Cover
(H11)
2 x Washer
(H12)
BackPanel
(P4)
6x Wooden Block
(P2)
Lower Glass
(P8)
2x Drawer Sides
(P10) Drawer Front
(P9)
Drawer Back
(P13)
Drawer Support
(P11)
Drawer Shelf
(P12)
Top Glass
(P7)
2 x Nut
(H13)
5 x Long Screws
(H14)
2 x Drawer
Runners
(H15)
2 x Bolts
(H16)
1 x Drawer
Handle
(H17)
Please check that you have everything before starting the assembly.

Carefully align the edges of the Wooden Blocks (P2) with the edges of Long Base Panel (P1), then
x with 12 x Dome Head Screws (H1)
Insert 4x Small Cam Bolts (H2) into 2x Side Panels (P3)
(P3)
(P3)
Step 3
4x Small Cam Bolts
(H2)
You will need:
4 x Small Cam
Nuts
(H2)
(H2)
(H2)
Insert the 4x Small Cam Nuts (H2) into the Back Panel (P4).
(P4)
Rotate the cam nuts so the arrows point towards the incoming cam Bolts.
Push the Side Panels into place and tighten the cam nuts.
This is how a cam nut works........
The head of the bolt
goes into the wide
mouth of the cam nut.
You then turn the nut
so the narrow part
closes over the bolt.
12 x Dome Head
Screws
(H1) (P1)

Page 5
Step 4
You will need:
2 x Small Cam
Bolts
(H2)
4 x Big Cam
Bolts
(H3)
4 x Wooden
Dowels
(H4)
Insert 2x Small Cam Bolts (H2), then 4x Big Cam Bolts (H3) and 4x Wooden Dowels (H4)
into the Long Base Panel (P1).
(P1)
(H3)
(H2)
(H2) (H4)
(H3)
(H4)
(H3)
(H4)
(H3)
(H4)
Step 5
You will need:
4 x BigCam
Nuts
(H3)
(H3)
(P4)
(P3)
2 x Small Cam
Nuts
(H2)
(H2)
Insert 2x Small Cam Nuts (H2) into the Back Panel and (P4) and 4x Big Cam Nuts (H3)
into the Side Panels (P3).
Rotate the cam nuts so the arrows point towards the incoming cam bolts.
Push the Back and Side Panels into place and tighten the cam nuts.
Mallet

Step 6
6
Step 8
Step 7
You will need:
6 x Short Timber
(H5)
Screws
2 x Drawer Runner
(H6)
Tracks
You will need:
2 x Small Cam
(H2)
(H3)
(H3)
4 x Big Cam
Nuts
Nuts
(H3)
(H2)
(H3)
Insert 2x Small Cam Nuts (H2)
into the Back Panel, then
4x Big Cam Nuts into Side Panels (P3).
Rotate the cam nuts so the arrows point
towards the incoming cam bolts.
Push the Drawer Top Panel (P5) into place and tighten the cam nuts.
(P5)
(P3)
You will need:
2 x Small Cam
Bolts
(H2) (H2)
(H2)
(P5)
4 x Big Cam
Bolts
(H3)
(H3)
(H3)
(H3)
(H3)
4 x Wooden
Dowels
(H4)
(H4)
(H4)
(H4)
(H4)
Insert 2x Small Cam Bolts (H2), 4x Big Cam Bolts (H3) and 4x Dowels (H4) into Drawer Top Panel (P5).
(H5)
(H5)
(H5)
(H5)
(H5)
(H5)
(H6)
front
Attach 2x Drawer Runner Tracks (H6),
to Side Panels with 6x Short Timber
Screws (H5).
Note:
Attach screws loosely. Then tighten the
front screw first, making sure the screw
aligns in the centre of the hole in the drawer runner.
Then tighten the other screws.
CR
CR

7
Fix 2x Glass Clamps (H7) to Drawer Top Panel (P5)
Tighten with phillips
head screwdriver
Step 9
You will need:
2x Glass Clamps
(H7)
Screw Short Threaded Rod (H8) into disc, and Long Threaded Rod (H9) into
rectangular block on Top Glass (P7). Tighten by hand.
Fix 2X Glass Clamps (H7) to Panel Glass Divider (P6).
Tighten with phillips
head screwdriver
Step 10
You will need:
2x Glass Clamps
(H7)
(P6)
Step 11
You will need:
(H7)
(P5)
(H7)
1 x Short
Threaded Rod
(H8)
(H8)
(H9)
1 x Long
Threaded Rod
(H9)

Place Stainless Steel Tube (H10) and
Tube Cover (H11) over Short
Threaded Rod.
Place Panel Glass Divider (P6) as shown
over Long Threaded Rod.
Insert 2x Wooden Dowel (H4) into Panel Glass Divider (P6).
note: Position the Panel Glass Divider with
the Glass Clamp as shown.
Step 12
(P6)
(H4)
(H10)
Page 8
Step 13
1x Stainless Steel Tube
(H10)
1x Tube Cover
(H11)
2x Wooden Dowels
(H4)
2 x Washer
(H12)
2 x Nut
(H13)
1 x Socket Wrench
(H13)
(H12)
(H13)
(H12)
Two people carefully turn over and lift assembled base over threaded rods. Fasten
tightly with 2x Washers (H12) and 2x Nuts (H13) using socket wrench provided.

Step 14
Use stubby phillips head
screw driver
Two people carefully turn over the assembled body, then insert Lower Glass (P8) into position
as shown. Tighten Glass Clamps with stubby Phillips Head screwdriver.
Step 15
Now Assemble the Drawer
(P9)
5 x Small Cam
Bolts
(H2)
(H2)
(H2)
(H2)
(H2)
(H2)
You will need:
Page 9
Screw 5x Small Cam Bolts (H2) into Drawer Front (P9).
(P8)

You will need:
5 x Small Cam Nuts
(H2)
(P9)
(P12)
(P13)
Step 16
Step 17
Step 18
Insert the 5x Small Cam Nuts (H2) into the Drawer Sides (P10) and Drawer Support (P11).
Rotate the cam nuts so the arrows point towards the incoming cam bolts.
Insert the Drawer Shelf (P12) into the groove on Drawer Sides and Drawer Front,
then attach Drawer Back (P13) with 5x Long Screws (H14).
Attach Drawer Runners (H15) to the underside of the drawer,
with 4x Short Timber Screws (H5).
Push the Drawer Side and Drawer Support into place and tighten the cam nuts.
(P11)
(H2)
(H2)
(H2)
(P10)
(P10)
Page 10
5 x Long Screws
(H14)
(H14)
(H5)
(H5)
(H5)
(H5)
(H15)
(H14)
(H14)
2 x Drawer Runners
(H15)
4 x Short Timber
Screws
(H5)