Lifestyle Solutions RETRO BED User manual

Box # 1 Box # 2
Optional Slats
13 pcs. Slats
2 pcs. Bed Side Rails
1 pc. Slat Support
1 pc. Head Board
1 pc. Foot Board
Parts And Fittings Packing Detail
Slat Hardware
32mm Screw - 20pcs.
(Wrapped in separate plastic bag)
4 pcs. Leg Support
RETRO BED
Bed Assembly Instructions
Page 1 of 2
A complete assembled view of
a Conventional Bed
M4 x 32mm Wood Screw
- 8pcs.
4mm Allen Key 1 pc.
Bolts M6 x 70mm - 4 pcs.
Washer - 12 pcs.
Hardware Pack in Box #1
5mm Allen Key 1 pc.
Bolt
M8 x 20mm - 4 pcs
Bolt
M8 x 45mm - 4 pcs
Wrench -1 pc.
Nuts - 4 pcs.
The Fusion Of Function And Comfort With Style

The Fusion Of Function And Comfort With Style
Page 2 of 2
Bed Assembly Instructions
Head board
Page 2 of 2
RETRO BED
Foot board
Slat support
Slat
Side
Rail
4nos M6 x 70mm
Bolt fastened to
4nos pre-drilled slats
Step 1/Diagram 1
Step 2/Diagram 2
Fix both side rails to the Head Board
and Foot Board as shown in diagram 1
with the 20mm and 45mm bolts and
washers.
Further secure the pre-drilled slats to the
slats support and support legs with 4nos
M6 x 70mm bolt as shown in diagram 2.
Finally, place both ends of the
assembled slats in the bed frame resting on
both sides of the side rails and screw them
inplace with the 32mm screws provided as
shown in diagram 3.
Step 3/Diagram 3
Diagram 1
Diagram 1
Diagram 3
Center Slat
Support
Leg Support
M6x70mm
Bolts
Leveler
Pre-drilled
Slat
M4 Allen
key
Foot Board Leg
Washer
M8 x 20mm
Bolt
Threaded Hole
Side Rail
Head Board
Washer
M8 x 45mm
Bolt
Metal Bracket
Through Hole
Washer
M8 Nut
Wrench
Side Rail
Metal Bracket
5mm Allen Key
Screw
Model shown for assembly instructions only
Fasten screws
to all slats
on side rails
Diagram 3

The Fusion of Function and Comfort with Style
LIFESTYLE SOLUTIONS
234 Series Casegood
Assembly of Metal Drawer Knobs. Step #1
Remove Drawer Knobs as shown
Step #2
Assemble knobs on the outside as shown.
To replace Wood knobs with the Metal knobs, remove the Wood knobs
and assemble the Metal knobs with the bolts provided along with the Metal knobs.
(Do not use Bolts from the Wood knobs on Metal knobs.)
Bolt
Drawer Knobs
2 Drawer Nigh stand Table 2 pcs
5 Drawer Chest 10 pcs.
6 Drawer Dresser 12 pcs.
TV Base 2 pcs.
Metal Knobs Bolt
Quantity of Knobs required per items

134/ 234/ 334/600 Series 6 Drawer Dresser
Removing of Center Leg
The center Leg is added for additional support. It is an optional extra.
You may remove it if you wish, The following steps will assist you in
doing this
First, turn the Dresser upside down as shown on a clean smooth
surface to avoid any scratches
STEP 1
Plastic Wrapper
6 Drawer Dresser
Remove the JCBC bolt from the cleat as shown by using the
Allen key provided. Then slide the support leg in the direction
shown above.
STEP 2
Center Leg
Allen Key
JCBC Bolt
slide
direction
The Fusion Of Function And Comfort With Style
LIFESTYLE SOLUTIONS
Allen Key Attached

234 Series Casegood
Fixing of Metal Door Knobs. Step 1
Remove Door knobs as shown.
Step 2
Refix knobs on the outside as shown.
To replace wood knobs with the metal knobs, remove the wood knobs
and assemble/fix the metal knobs with the bolts provided
with the metal knobs.
(DO NOT USE bolts from the wood knobs on metal knobs)
Knob
Bolt
Pull string to
open the door
Metal Knobs-2 pcs Bolt-2 pcs
The Fusion of Function and Comfort with Style
LIFESTYLE SOLUTIONS
Fixing ToolAdditional part
1 pc - wooden rod Phillips screw driver