Neumaerker 05-50370 User manual

Lohstr. 13 - 58675 Hemer / Postfach 4063 - 58663 Hemer
Telefon: [phone] Fax: [phone]
DEUTSCHLAND
Operating Manual
Ceramic Glass
Salamander PDS
Art.-Nr. 05-50370
www.neumaerker.de

SALAMANDER PDS
Congratulations for the acquisition of this upmarket appliance. You chose an
appliance which alloys the best technical qualities with a big user-
friendliness. We wish you the biggest contentment.
1. SECURITY INSTRUCTIONS
Please respect these instructions scrupulously to avoid any
risk of fire, electric shock, scald or other wounds and dam-
age. During the use of this appliance, fundamental circum-
spection of security must always be noticed, such as:
-Take into account the instructions to be systematically
kept with the appliance.
-Install the appliance always in instructions respect. A
50 cm distance minimum with the partition or the wall
is necessary (except on the rear part).
-Protect the appliance from direct light of the sun, frost
and humidity.
-Never leave the appliance within the reach of children
or disabled persons without surveillance.
-Ensure that only trained personnel operate the appli-
ance.
-Never move the appliance when it is working or when
the cooking surfaces are still hot.
-Check that the appliance is definitely off before con-
necting it up or disconnecting it.
-Do not touch the hot surfaces of the appliance. The
temperature of the hot surfaces can be very important
when the appliance is working.

Always use handles and control knobs.
-Do not use the appliance for other functions than de-
termined use.
-Do not leave the cord of electrical feeding in the con-
tact of hot surfaces.
-The appliance should not be used close to combustible
materials.
-During use, look after not to obstruct hearings of aera-
tion of the appliance.
-To avoid any electric shock, never plunge the appli-
ance, the cord or plug in water or quite other liquid.
-If the cord is harmed, it must be replaced by the pro-
ducer, his after sale service or persons of similar skills
to avoid any risk.
-Entrust compensations only to a skilled person.
-Use only spare parts of origin.
-At the end of cooking, before cleaning the appliance,
do not forget to disconnect it.
2. CONTENTS OF CARDBOARD PACKAGING
Device: a salamander
Accessories: - A tray
-A grid
-The present note
See exploded view at the end of the document.
3. CONFORMITY OF USE
Use the device only to defrost, brown, glaze, grill toasts, gratins, pizzas, onion
soups… without pre-heating.
4. WAY OF FUNCTIONING
This salamander is fitted with two cooking areas, a removable inside tray with a grid, a
commutator to select the cooking zone, an energy regulator to set the power and a
plate detection system (PDS).

The top of the salamander is movable and enables you to adapt the cooking position
to grill, glaze or brown your foodstuffs.
To turn on the salamander, just set the commutator (n°5 on picture) on one of the
position according to the desired cooking zone to be used, set the energy regulator
(n°2 on picture) on the desired power (the position C enables to obtain a continuous
heating power).
Your salamander is fitted with a plate detection system (PDS/n°1 on picture). When
the commutator is on position Start, the heating will automatically work when you
place a plate or tray in contact with the plate detection system (n°6 on picture). To
use this function, the energy regulator (n°2 on picture) has to be set on C position
If the PDS commutator (n°1 on picture) is on position 0, your salamander is running
continuously and is regulated by the energy regulator
The green pilot light (n°4 on picture) indicates the salamander is on. The orange one
(n°3 on picture) indicates the salamander is heating up
Position 1 : Left area
Position 2 : Right area
Position 3 : Complete area.
PDS commutator Energy regulator
Control pilot light On/off pilot light
Commutator Plate detection system (PDS)
2
1
34
6
5
4
2
6
3
1
5

5. FUNCTIONING / MANIPULATION
a) Installation / assembly:
-Unpack carefully the device of its packaging.
-Place the salamander on a plane and heatproof surface.
-Never place the device near a wall or near a partition makes of combustible
materials even if it is very well isolated.
-A distance of minimum 50 cm with the partition or the wall is necessary (except
on the rear part)
-Remove the protective film from the top, the rear, the sides and the tray.
-Unlock the movable top by unscrewing the screw located on the back of the
machine thanks to a 10 pipe key.
-In case of connection directly to the electrical network, a disconnection mode
has to be planned in conformity with the norms.
CAUTION :
During use: never place the machine on surfaces or near walls, partitions or
kitchen furniture and similar— except if they are made with a non combustible
material or recovered with non combustible thermic insulation, and pay atten-
tion to fire preventions rules.
b) First starting:
During the first use, warm your machine up outside to evacuate residual smokes of
manufacturing oil from the metallic parts. This may emit a slight smell for a few mo-
ments.
First cleaning
Clean the device before the first use. (See 6. Cleaning)
Connection of the device
-Check that the tension and the frequency of the electricity network suit to the values
indicated on the descriptive plate.
-Make sure that every control knob is positioned on 0.
-Unwind completely the electric power cable and connect it in a plug connected with
the earth.
-The device is connected.
NB: in case of connection of the device in a plug without earth protection or directly
on the electricity network, confide its connection to a qualified person .

c) Use of device :
Elements of command and display
Putting on
Turn on the commutator control knob (n°5 on picture) on wished position according to
desired cooking zone to be used and the energy regulator (n°2 on picture) on wished
power.
The pilot lights (n°3 and 4 on picture) ignite.
To use the plate detection system (PDS), set the commutator on Start position and
the energy regulator on position C.
The cooking with infrared radiation does not need preheating.
Stopping the appliance
Set the commutator control knob, the PDS commutator and the energy regulator
on 0
Disconnect the power cable.
Let the device cool down
Clean the appliance. (see 6. Cleaning)
Command/Display Function
PDS commutator (n°1 on
picture)
Plate detection system on/off
Energy regulator (n°2 on
picture)
Regulates the heating power
Orange pilot light (n°3 on
picture)
Heating up (pilot light on)
Green pilot light (n°4 on
picture)
On/off for each cooking area (pilot light on)
Commutator 4 positions (n°5
on picture
Cooking area selection
Stop Stop StopContinuous
Start
Start
Right area
Left area All
areas

d) Breakdown / repair:
In case of breakdown or of damaged part, please call your after-sales service and con-
fide any technical operation to qualified person.
When you contact the after-sales service of your distributor or your store, give him the
complete reference of your device (commercial name, type and serial number). This
information appears on the visible descriptive plate behind the device.
6. CLEANING AND MAINTENANCE
Disconnect the device.
-Let cool completely the device before any technical intervention or cleaning.
-Never clean the ceramic glass when it is hot.
-Clean regularly the external walls of your device with warm water and wash liquid:
avoid the abrasive towelling. Rinse your device with a wet sponge.
-Never clean the device under a water jet, the infiltrations would risk to damage it in a
irreparable way.
-Never immerse the device, the cord or the plug in the water or quite other liquid to
avoid any electric shock.
-During a prolonged non-use, we recommend you strongly to keep the device shielded
from the humidity.
7. TECHNICAL SPECIFICATIONS
We recommend to connect this equipment on a power socket of a capacity of
16A minimum
Wires colours correspondence Phase Brown / Black / Grey
Neutral Blue
Earth Yellow-Green
The equipotential connection marked by this symbol must be linked with
the equipotential conductive connection of your installation by means of a minimum
conduction of a 2.5 mm² section.
Model
Salamander PDS
Voltage 220-240 V ~
Current 13 A
Power 3000 W
Weight 56 Kg
Nb element 2
Cooking surface 495x375 mm
Outside dimensions 600x640x590 mm

8. NORMS AND LEGALS DISPOSALS
The device is conform to :
IEC/EN 60335-1
IEC/EN 60335-2-48
EN 55014-1 + 55014-2
EN 61000-3-2 + 61000-3-3
Humidity protection degrees IPX3, in conformity with the norm 60335-2-48 (2008)
9. ELIMINATION OF THE ELECTRIC AND ELECTRONIC WASTE
The device respects the directives:
2002/96/CE (DEEE) N°34270064800021
2002/95/CE (ROHS)
2066/95 CE
2004/108 CE
Reach rule
Never put the device among household waste.
The device must be put down in a centre of recycling for the electric equipments.
The materials of the device are indeed reusable. By eliminating correctly the electric
and electronic wastes, the recycling and quite other shape of re-use of worn equip-
ments, you participate in a significant way in the environmental protection.
For any information about the collection of electric and electronic waste, please con-
tact your distributor.
10. GUARANTEE
Conditions of guarantee
The guarantee applicable to any device is the commercial guarantee of the distributor
or the retailer. Please contact the store where you bought your device to know the
precise conditions.
The guarantee grants no right for damages.
The dispositions which follow are not exclusive of the profit of the legal guarantee
planned by articles 1641 and following ones of the Civil code relative to the defects
and the latent defects.

Exclusion clauses of the guarantee
Bad installation and bad maintenance, in particular if they do not respect cur-
rent regulations or instructions appearing in this user guide.
Cannot benefit from the guarantee the repairs required as a result of false operations,
of inappropriate use, of carelessness or of excess loads of the device, as well as
those resulting from variations of the power supply, over tension or from defective in-
stallations.
The damage due to shocks, bad weather is not flatware by the guarantee. The materi-
al travels at the risks of the user; in case of delivery by carrier, the consignee has to
have reservations towards the carrier before any delivery of the device.
The guarantee comes to an end in case of intervention, of repair, of modification by no
qualified persons, or of use in inappropriate purposes.

ORANGE
1V 1U
2V 2U 2W
PH1 N T
1W
TERMINAL PLATE
TERMINAL PLATE
1W 1V 1U
2V 2U 2W
COMMUTATOR
G7
C
A
5
1
3
GREEN
HEATING ELEMENT
HEATING ELEMENT
ENERGY-REGULATOR
P2
P1 2
4
ENERGY-REGULATOR
MICROSWITCH
COMMUTATOR
3a 3
S1 S2
31/08/2016
Date :
31/08/2016
SEM 600 PDS 3000 W
Date :

CODE QTE SPARE PART
70094 18 WEIGHT AGAINST SALAMANDER
70097 1 WEIGHT C OUNTER LOCK SEM/SGM 600
70098 1 BACK CASING SEM/SGM 600
70099 1 FRAME H OLDER SEM 600
70100 1 REAR COVER SEM 600
70102SE 1 BOTTOM CASING
70104SE 1 WEIGHT C OUNTER HOLDER
70105 1 TRAY SEM/SGM 600
70111 1 DEFLECTOR SEM/SGM 600
70112 1 ROOF SEM 600
70114 10 BACK AGAIN ST WEIGH T SEM 60 VC
70122SE 1 TRAY SEN SOR REF A SEM 600 PDS
70123 2 TRAY DETECTOR REF B SEM 600 PDS
70124 1 MICROSWITCH HOLDER REF A SEM 600 PDS
70125 1 MICROSWITCH HOLDER REF B SEM 600 PDS
70126 1 REAR SEM 600 PDS
70127 1 BASE SEM 600 PS
70128 1 CERAM IC CHAM BER SPAC ER SEM 600 PDS
70129 2 CERAM IC CHAM BER LOCK SEM 600 PDS
70130 1 REFLECTOR SEM 600 PDS
72054D 1 RIGH T WIRE HOLDER SEM/SGM
72054G 1 LEFT WIRE HOLDER SEM/SGM
72059 1 LEFT BEARING H OLDER SEM/SGM
72060 1 RIGH T BEARING HOLDER SEM/SGM
72061SE 1 LEFT ROOF HOLDER SEM/SGM 600-800
72062SE 1 RIGH T ROOF HOLDER SEM/SGM 600-800
72063 1 DOMINO H OLDER SEM 600/800
72064 2 INSIDE UPRIGHT SEM /SGM 600-800
72075 1 H ANDLE SPACER SEM/SGM 60-80
72084D 1 RIGH T CHAIN C OVER SEM/SGM 600-800
72084G 1 LEFT CHAIN C OVER SEM/SGM 600-800
A01001/1 1 COMMUTATOR 4924215001
A01015 1 COMM UTATOR RE 2
A04006 1 REGULATOR
A07037 1 MICROSWITCH 20 A 250 V
A08003 1 ORANGE PILOT LIGH T DIAM 12
A08009 1 GREEN PILOT LIGH T DIAM 12
A10032 1 CORD CLOSER
A12002 2 CABLE SHOE DA 200, RF14, RG8
A12003 4 CABLE SHOE CA
A12011 2 CABLE SHOE DA 110
A13003 2 RUBBER FOOT
A13006 4 FOOT
A14078 3 KNOB 12 H FOR ELECTRIC
A15018 1 HANDLE SALAMANDER
A16010 2 TERMINAL PLATE
B01002 4 GEAR WHEEL
B04098 6 BEARING AXLE SEM 800/SEM 600
B04099 2 WEDGE ADJUSTMENT SEM 800/600
B04100 2 BEARING HOLDER SEM 800
B06004 4 PIN SLIT 3.2 x 25
B06009 2 STUD + N U T
B06017 10 BEARING
B06060 1 MICROSWITCH AXLE SEM 600 VC PDS
B07001 4 COMPRESSION SPRING
B07004 2 SPRING
B07028 2 CHAIN
C03P05411 1 CORD
C05018 1 EQUIPOTENTIAL TERMINAL
D06009 2 CERAMIC CHAMBER 1500 W
F01071 1 GRID SEM/SGM 600
F02007 2 TRAY SLIDE
G06P05411 1 FRONT PANEL
H01073 1 GLASS CERAMIC SEM 600
I17001 1 STAINLESS STEEL SCREW 4 x 8
I18011 2 NUT DIAM 4
TP0010_555 2 GEAR WHEEL HOLDER AXLE
31/08/2016
Date :
31/08/2016
SEM 600 PDS 3000 W
Date :

B04098 (x6)
70112
A15018
72061SE
70097
C05018
B04100 (x2)
72064 (x2)
B06017 (x10)
A12003 (x4)
A13003 (x2)
A16010 (x2)
72063
72062SE
TP0010_555 (x2)
72084G
72075
70111
70130
70099
B07001 (x4)
70129
70129
70128
H01073
D06009 (x2)
70126
70100
70122SE
70123 (x2)
F02007 (x2)
70127
G06P05411
A14078 (x3)
F01071
70102SE
B06009 (x2)
I18011 (x2)
70105
A10032
C03P05411
A12002 (x2)
A01001_1
A01015
A04006
A08003
A08009
A13006 (x4)
72054G
72060
B01002 (x4)
70114 (x10)
70094 (x18)
70104SE
70098
I17001
70125
B06060
A07037
70124
72059
A12011 (x2)
72054D
B06004 (x4)
B07004 (x2)
B07028 (x2)
B04099 (x2)
72084D
31/08/2016
Date :
31/08/2016
SEM 600 PDS 3000 W
Date :