New England Arbors VA80350 User manual

Pergola Extension Kit
ASSEMBLY INSTRUCTIONS
Check Box for These Contents
In the event of missing or defective parts please call our customer service department at 1 800 282 9346 (Mon. to Fri. 8:00 AM to 4:00 PM EST).
Please read through before starting installation.
V1.0/112916
VA80350 - 4 Pack Pergola Extension Kit - White
VA84350 - 4 Pack Pergola Extension Kit - Composite
1
2
5
4
1.
2.
3.
4.
5.
6.
7.
Top Trim Cap (4) White #10764 Composite #14055
Tall Extrusion (4) White #10175-1 Composite #14092 - 6” x 6” x 36”
Bottom Trim (4) White #10765 Composite #14057
Post Joiner (4) - White #10725-1 Composite #14052
Post Extension (4) - White #10254 Composite #14093 - 5” x 5” x 24”
1 1/2” Pan Head Steel Screw (64) - White #20005 Composite #20031
Vinyl Glue (1) - White #20000 Composite #20022
4 Pack Pergola Extension Kit
7
24 in
36 in
37 1/8 in
6 in
5 in
VA80352 - 2 Pack Pergola Extension Kit - White
VA84352 - 2 Pack Pergola Extension Kit - Composite
3
6
1.
2.
3.
4.
5.
6.
7.
Top Trim Cap (2) White #10764 Composite #14055
Tall Extrusion (2) White #10175-1 Composite #14092 - 6” x 6” x 36”
Bottom Trim (2) White #10765 Composite #14057
Post Joiner (2) - White #10725-1 Composite #14052
Post Extension (2) - White #10254 Composite #14093 - 5” x 5” x 24”
1 1/2” Pan Head Steel Screw (32) - White #20005 Composite #20031
Vinyl Glue (1) - White #20000 Composite #20022
2 Pack Pergola Extension Kit

2 Pergola Extension Kit Instructions
3
Using the glue provided, run a small bead around the inside of the
base molding extrusion.
Carefully place the bottom trim on one end of the base molding
extrusion.
Run another bead of glue on the other (inside) end of the base molding
extrusion.
Carefully place the top trim cap on the base molding extrusion.
Repeat for all base moldings.
Note: Please allow the glue to set for 15 minutes prior to installing the
base molding on the pergola.
1
2
STEP ONE
4
1
2
3
4
5
5
Base Molding Assembly

3
Pergola Extension Kit Instructions
3
Using the glue provided, run a small bead around the inside of the
Post Extension as shown.
Carefully place the post joiner in the post extension.
Repeat for all Post Extensions.
Note: Please allow the glue to set for 15 minutes prior to installing the
post extension on the pergola.
1
2
STEP TWO
Post Extension Assembly
1 2 3

Wooden post.
4Pergola Extension Kit Instructions
3
Identify the bottom of the pergola post; in most cases, the top of
the pergola post will have pre-routed holes.
Slide the base molding assembly over the pergola post through
the bottom side as shown.
Apply a bead of glue to the (bottom) inside of the pergola post.
Insert the post extension assembly from the previous step.
After installing the pergola post (with extension) over the wooden
post, fasten the post extension to the wooden post using sixteen
screws provided. Screws should be roughly 1 in above and 1 in below
the seam of the post joiner. Keep the screws within the 3" center of the
column to allow the base mold to slide over them. (see illustration).
Lower the base molding to cover the post extension.
1
2
STEP THREE
4
1
2
3
4
5
Post Extension Installation
6
Notes:
1. Ideally the post extension should be installed before the pergola
posts are installed.
2. This extension is designed to extend the pergola posts by 24”; if a
shorter height is desired, the post extension (part#5) can be cut
down to accomodate a shorter extension. Use a fine-tooth blade
saw.
3. Typically the wooden post should also be extended by the same
height as the post extension.


6
5