Sunjoy D-GZ840PST-C User manual

Cautions:
Sunjoy D-GZ840PST-C 10' x 12' Wyndham Hardtop Gazebo
- Black Top
Owner’s Manual
IMPORTANT
Thank you very much for choosing Sunjoy Group.
Please take time to read these instructions thoroughly and follow each step carefully for safe and easy
operation. Keep this manual for future reference.
We would like to hear from you with any comments or suggestions. You can call us toll-free at
1-866-578-6569 from 8:00 a.m. EST to 8:00 p.m. PST. You can also send the email to
[email protected] or visit www.sunjoyonline.com to get tech. assistance or to place your
replacement part order form.

Cautions:
1. Keep all children and pets away from assembly area. Children and pets should be supervised
when they are in the area of gazebo construction.
2. The area for assembly should not be less than 6 feet from any obstruction such as fence, garage,
house, overhanging branches, laundry line or electrical wires.
3. The unit is heavy. Don’t assemble alone. Six people are recommended for safe assembly.
4. Some parts may contain sharp edges. Wear protective gloves if necessary during assembly.
5. When assembling and using this product, basic safety precautions should always be followed to
reduce the risk of personal injury and damage to equipment. Please read all instructions before
assembly and use.
6. For outdoor use only. Install on level ground. 16 stakes are provided to secure the gazebo in the
ground. If you wish to secure the pavilion to a wood deck or concrete surface, use 16 anchors suited
for these surfaces (anchors not included).
7. Check all bolts for tightness before and during usage
8. Pegs supplied must be used to hold this gazebo in place when upright.
9. Warranty does not cover damage due to extreme weather conditions.
10. Do not use candles, matches or open flames of any kind in or near item. Do not cook inside.
11. Build campfires downwind and several meters away from a tent and be sure to fully extinguish
campfires before leaving a campsite or before retiring for the night.
12. Exercise extreme caution when using fuel-powered lanterns or heaters inside a tent and use
battery-operated lanterns whenever possible.
13. Extinguish or turn off all lanterns before going to sleep. Do not smoke in a tent.
14. WARNING: KEEP ALL FLAME AND HEAT SOURCES AWAY FROM THIS TENT FABRIC. This
tent is made with fabric that meets CPAI-84 specifications for flame resistance. It is not fire proof.
The fabric will burn if left in continuous contact with any flame source.
Assembly Instructions:
Our clear, easy-to-follow, step-by-step instructions will guide you through the project from start to
finish. The final product will be a quality piece that will go together smoothly and give years of
enjoyment.
All you will need is a screwdriver, a hammer and two ladders of at least 8 feet (2.5 m) high (not
included).
Loading limit of the hook is 45 lbs.
Parts identification: For ease of identification, all parts are labeled to correspond to the Step number
in which the part is used.

Parts List
A1 Big top frame 2PCS
B1 Big top bar 2PCS
C1 Small top support beam 4PCS
D1 Small top connector 1PCS
E1 Pothook 1PCS
F1 Small top roof panel 1 2PCS
G1 Small top roof panel 2 2PCS
H1 Small top cover 4PCS
I1 Small top roof cover 1PC
F2 Slanting bar connector 4PCS
G2 Beam connector (upper) 4PCS
H2 Beam connector (down) 4PCS
K1 Short beam 1 2PCS
K2 Short beam 2 2PCS
J1 Long beam1 2PCS
J2 Long beam 2 2PCS
L2a Long pipe 1 2PCS
L2b Long pipe 2 2PCS
M2a Short pipe 1 2PCS
M2b Short pipe 2 2PCS
P1 Big panel 1 2PCS
P2 Big panel 2 2PCS
P3 Small panel 1 2PCS
P4 Small panel 2 2PCS
Q Fence 8PCS

A3 Top slanting bar 4PCS
B3 Top beam 4PCS
C3 Long side left roof panel 1 2PCS
D3 Long side right roof panel 1 2PCS
E3 Long side left roof panel 2 2PCS
F3 Long side right roof panel 2 2PCS
G3 Long side left roof panel 3 2PCS
H3 Long side right roof panel 3 2PCS
I3 Short side roof panel 1 2PCS
J3 Short side left roof panel 2 2PCS
K3 Short side right roof panel 2 2PCS
L3 Short side left roof panel 3 2PCS
M3 Short side right roof panel 3 2PCS
N3 Big roof panel cover (corner) 4PCS
O3 Big roof panel cover (middle) 4PCS
W Panel wall 8PCS
W1 Short beam of big roof(short side) (1) 2PCS
W2 Short beam of big roof(short side) (2) 2PCS
W3 Middle beam of big roof(short side)(1) 2PCS
W4 Middle beam of big roof(short side) (2) 2PCS
W5 Long beam of big roof(short side) (1) 2PCS
W6 Long beam of big roof(short side) (2) 2PCS
X1 Short beam of big roof(long side) (1) 2PCS
X2 Short beam of big roof(long side) (2) 2PCS
X3 Middle beam of big roof(long side) (1) 2PCS
X4 Middle beam of big roof(long side) (2) 2PCS
X5 Long beam of big roof(long side) (1) 2PCS
X6 Long beam of big roof(long side) (2) 2PCS

AA M6*15 Bolt 84 PCS
BB M6 Bigger flat washer 250PCS
CC M6*60 Bolt 16PCS
DD M6 Nut 32 PCS
EE M6*35 Bolt 8 PCS
FF M6*15 Bolt 80 PCS
GG M6*70 Bolt 16 PCS
LL M6*35 Bolt 16 PCS
JJ M6*25Bolt 12PCS
HH M6*45Bolt 2 PCS
Z M6 Wrench 2 PCS
Hardware Pack 1

Fig.1: Fix Big top frame A1 and Big top bar B1 by using AA, BB.
Fig.2: Fix Small top support beam C1 and Big top frame A1 by using AA, BB.
Fig.3: Fix Small top support beam C1
and Small top connector D1 by using
DD, BB, CC.
Fig.4: Screw the Pothook E1 into Small
top connector D1.
Fig.5: Screw the Fence Q into
Big panel P1 (P2) and Small
panel P3 (P4) by using FF, BB.
Fig.6: Fix Big panel P1(P2) and Small panel P3(P4)by using JJ, BB.
Fig7: Attach Beam connector
G2/ H2 to Long beam J1/J2
and Short beam K1/K2 by
usin
g
GG
,
BB
,
DD.
Fig7-1: Fix Panel P1, P2, P3,
P4 and Long beam J2 and
Short Beam I2 by using FF, LL,
BB.
Fig7-2: Fix Slanting bar
connector F2 onto panel P1,
P2, P3, P4 by using FF, BB.

Fig.8-1: Attach Top slanting bar A3
and Top beam B3 to Big top frame A1
by using FF, BB. (Do step fig8.1 and
fig8.2 at the same time, which is
needed 2 pieces of 2M ladder.)
Fig.8-2: Attach Top slanting bar A3 to Slanting bar
connector F2, Top beam B3 to Beam connector G2 by
using CC, BB, DD. (Do step fig8.1 and fig8.2 at the
same time)
Fig.11: Attach Big roof top beam X6 (X5/W5/W6）and Top slanting bar A3 by using AA, BB.
Fig.12: Attach Big roof top beam X5 to Top beam B3 by using AA, BB.
(Repeat the procedure for X1-X6, W1-W6.)
Fig.13: Attach Big roof top beam X4 to Top slanting bar A3 by using AA, BB
(Repeat the procedure for X1-X4, W1-W4.)
Fig.13-1: Attach Long pipe L2a (L2b), Short pipe M2a (M2b) and Top beam B3 by using AA and BB.
Fig.13-2: Attach Long pipe L2a (L2b), Short pipe M2a (M2b) and Top slanting bar A3 by using AA, BB.
Fig.9: Fix Small top roof panel 1 F1 and Small top
roof panel 2 G1 onto Small top support beam C1 by
using AA, BB.
Fig.10: Fix Small top cover H1 onto Small top support beam C1
by using EE, BB, then fix Small top roof cover I1 and Small top
connector D1 by using HH,BB.

AA M6*15 Bolt 44 PCS
BB M6 Bigger washer 60 PCS
EE M6*35 Bolt 16 PCS
KK Φ6X260 Stake 16 PCS
Hardware Pack 2
Fig.14-1: Assemble Long side left roof panel C3 and Long side left roof panel E3 for a whole piece.
Fig.14-2: Attach the assembled Long side left roof panel C3 and Long side left roof panel E3 onto the top frame
by using AA, BB (Repeat the procedure for D3, F3, G3, H3, I3, J3, K3, L3, M3)

AA M6*15 Bolt 4 PCS
BB M6 Bigger flat washer 10 PCS
CC M6*60Bolt 2 PCS
DD M6 Nut 3 PCS
EE M6*35 Bolt 2 PCS
FF M6*15 Bolt 4 PCS
GG M6*70 Bolt 2 PCS
LL M6*35 Bolt 2 PCS
JJ M6*25 Bolt 2 PCS
HH M6*45Bolt 1 PCS
Fig.15-1: Insert Big roof
panel cover N3 into the
hole of Small top
support beam C1.
Fig.17: Fasten the whole
gazebo to the ground with
Stake KK.
Backup Parts
Fig.16: Attach Panel wall
(W) into tube with
preassembled
hook-and-loop fasteners.
Fig.15-2: Then attach Big roof
panel cover N3 to Top slanting
bar A3 by using EE, BB, lock Big
roof panel cover O3 onto Top
beam B3.by using EE,BB

Care & Maintenance:
Our steel components for garden accessories and furniture are treated with rust inhibiting paint that
protects it from rusting. However, due to the nature of steel, surface oxidation (rusting) will occur
once these protective coatings are scratched. This is not a defect and thus not covered by the
warranty.
To minimize this condition, we recommend care when assembling & handling the product to prevent
scratching the paint. Should any scratching or damage occur, we recommend immediate touch-up
with rust inhibiting paint.
Surface rust can also be easily removed with a very light application of common cooking oil. If
surface oxidation (rusting) occurs and if no measure is taken to prevent this, the oxidation may start
dripping on to deck or patio and caused damaging stains, which may be difficult to remove. This can
be prevented if the above-mentioned measures are taken to keep the product from oxidizing.
Limited Manufacturer’s Warranty:
This limited warranty is extended to the original purchaser and applies to defects in materials and
workmanship of your item provided the item is maintained with care and used only for personal,
residential purposes.
The item is warranted to be free from defects in material or workmanship for a period of one (1) year.
We don't reimburse for transportation or delivery costs, or compensate the individual or any outside
party for assembling or disassembling the product.
Exclusions:
Items used for commercial, contract, or other non-residential purposes, or items damaged due to
acts of nature, vandalism, misuse, or improper assembly are not covered. Corrosion or rusting of
hardware is not covered. Proof of purchase (dated register receipt) is required for warranty claims.
Warranty is to the original purchaser and is non-transferable. Any replacement of warranted items
will be in the original style and color, or a similar style and color if the original is unavailable or has
been discontinued. As some states do not allow exclusions or limitations on an implied warranty, the
above exclusions and limitations may not apply. This warranty gives you specific rights, and you
may also have other rights, which vary from state to state.
Made in China