New England Arbors Vienna User manual

Check Box for These Contents
In the event of missing or defective parts please call our customer service dept. at
1 800 282 9346 (Mon. to Fri. 8:00 AM to 4:00 PM EST).
(UK Tel: [phone] (Mon. to Fri. 1:00 PM to 10:00 PM GMT).
1. Keystone Lid
(1) - 10668-1
2. Keystone Insert (1) - 10837
3. Keystone Body (1) - 10836
4. Keystone Bottom Plate (1) - 10666-1
5. Arch Spindle - Long (2) - 10878
6. Arch Spindle - Short
(2) - 10879
7. Arches (2) - Left 10880 , Right 10881
8. Post Caps (2) - Left 10673-1 , Right 10674-1
9. Top Rail (1) - 10882
10. Posts (2) - Left 10883 , Right 10884
11. Vertical Spindles (7) - 10885
12. Horizontal Spindles (3) - 10886
13. Bottom Rail (1) - 10887
14. Ground Mounting Extensions (2) - 10888
15. 1 1/2”[38 mm] Self-Auguring Stainless Steel Screws (20) - 20005
Tools You Will Need
• Cordless Drill
• Hammer
• Tape Measure
• Level
• Shovel
General Information
•Read Instructions through carefully before beginning assembly.
• When assembling components, place on a non-abrasive surface (i.e. shipping box) to avoid scratching.
• We recommend an area approx 5’x 8’ (1.5 m x 2.4 m) for unobstructed assembling.
•You should not need to use excessive force when assembling component.
The Vienna Trellis
Please read through before starting assembly.
ASSEMBLY INSTRUCTIONS
1
1
2
15
Not to Scale
6
3
4
5
IMPORTANT: CHECK THE INSIDE OF YOUR POSTS FOR ALL MATERIALS.
V1.4/072717
14
83.75 in
(212.7 cm)
49 in (124.5 cm)
42 in (106.7 cm)6 in
(15.2 cm)
49 in
(124.5 cm)
2 in
(5.1 cm)
7
8
9
10
11
12
13
www.newenglandarbors.com
www.newenglandarbors.co.uk

2
www.edenarbors.com
1
Lay out the top rail,bottom rail,horizontalspindles,and
vertical spindles as shown. Start by inserting the 7 vertical
spindles into the 3 horizontal rails.
Note that the routed holes on the horizontal rails are slightly
offset from the centre. Ensure that the holes are aligned as per
the inset image.
Continueto inserttheassemblyinto the top and bottom rails.
Ensure that the vertical spindle notched ends are fully inserted
into the top/bottom rails, just past the notched ends.
Note the difference between the two rails. The bottom rail only
hasonerouted side whereas the top rail has additional holes
for the arch spindles.
Align and insert the rails into one of the post.
Note that the pre-drilled holes are located on the back side
of the trellis.
Proceed with the other post.
Flip the trellis over and using the provided screws,fasten
the posts to the top and bottom rails in place asshown.
1
2
3
4
STEP ONE
2
3
NOTE: Assembly will be easier if performed by two people
Note orientation
5
5
The Vienna Trellis

3
STEP T WO
Assemble the keystone by inserting the keystone insert into the keystone
body as shown below,followed by the two arches.
Note that the arches will be marked with a sticker where they meet the
keystone.
Using two of the provided screws,fasten the arches into the keystone
insert as shown.
Drive two more screws to the underside of the keystone.
Snap the top and bottom lid to complete the arch assembly.
Arch Assembly
1
Insert first
2
3
4
1
2
3
4
Sticker
Sticker
The Vienna Trellis

4
STEP TH REE
Place the post cap onto each of the post.Note that there are left and
right post caps.Please see image aside for orientation.
Insert the arch spindles into the top rail as shown.The short spindles
would be on the outer side of the rail,and the long spindles would
be on the inner side of the rail.
Starting on one end,guide the arch assembly and arch spindles
into the pre-routed holes as shown.
Fasten the arch assembly to the posts using fourscrews (2 per post)
provided.
Arch Assembly
1
2
3
4
1
Long
2
Long
Short
Short
3
4
The Vienna Trellis

5
4
Move the trellis to its final location. When you are satisfied with
the location,mark the positions of the posts,then move the trellis
aside and lay it carefully on it’s side. Excavate the 2 post holes
approximately 12" [30.5cm] deep x 6" [15.2cm] diameter.
Carefully move the trellis back into position.
Level it both vertically and horizontally into the excavated holes.
Backfill the holeswith the excavated soil.
Note: For a stronger installation,purchase two 2x4 [35mm x
90mm equivalent] pressure treated lumbers and sleeve them
into the posts.Wood posts should be inserted 4”[10.2cm] into the
trellis posts and ±24” [61cm] into the ground.
A
B
C
Mounting Into the Ground
Trellises must be well secured in the event of high winds, etc. We
have provided two ground mounting extensions for securing the
trellis either into the ground or into a concrete footing. If
you are installing your trellis directly to the wall of your home, or on a
wood deck or concrete surface, please see your hardware store for the
appropriate galvanized bracket hardware.
STEP FOUR
Install the Ground Mounting Extensions
Insert the ground mounting extensions into the bottom of the
trellis posts. Secure with screws as shown aside.
STEPFIVE
Install Trellis into Ground
A
5
12”
30.5cm
Level
6“
15.2 cm
B
C
www.newenglandarbors.com
www.newenglandarbors.co.uk
North America Toll Free Phone: [phone]
United Kingdom Tel: [phone]