Newport XPS User manual

XPS Controller
Universal High-Performance
Motion
Controller/Driver
Quick Start

XPS Motion Controller/Driver Quick Start
Warranty
Newport Corporation warrants that this product will be free from defects in material and
workmanship and will comply with Newport’s published specifications at the time of
sale for a period of one year from date of shipment. If found to be defective during the
warranty period, the product will either be repaired or replaced at Newport's option.
To exercise this warranty, write or call your local Newport office or representative, or
contact Newport headquarters in Irvine, California. You will be given prompt assistance
and return instructions. Send the product, freight prepaid, to the indicated service
facility. Repairs will be made and the instrument returned freight prepaid. Repaired
products are warranted for the remainder of the original warranty period or 90 days,
whichever comes first.
Limitation of Warranty
The above warranties do not apply to products which have been repaired or modified
without Newport’s written approval, or products subjected to unusual physical, thermal
or electrical stress, improper installation, misuse, abuse, accident or negligence in use,
storage, transportation or handling. This warranty also does not apply to fuses, batteries,
or damage from battery leakage.
THIS WARRANTY IS IN LIEU OF ALL OTHER WARRANTIES, EXPRESSED OR
IMPLIED, INCLUDING ANY IMPLIED WARRANTY OF MERCHANTABILITY
OR FITNESS FOR A PARTICULAR USE. NEWPORT CORPORATION SHALL
NOT BE LIABLE FOR ANY INDIRECT, SPECIAL, OR CONSEQUENTIAL
DAMAGES RESULTING FROM THE PURCHASE OR USE OF ITS PRODUCTS.
©2017 by Newport Corporation, Irvine, CA. All rights reserved.
Original instructions.
No part of this document may be reproduced or copied without the prior written
approval of Newport Corporation. This document is provided for information only, and
product specifications are subject to change without notice. Any change will be
reflected in future publishings.
EDH0205En1051 – 10/17 ii

XPS Motion Controller/Driver Quick Start
Table of Contents
Warranty................................................................................Erreur ! Signet non défini.
Preface..............................................................................................................................v
Confidentiality & Proprietary Rights...............................................................v
Sales, Tech Support & Service .............................Erreur ! Signet non défini.
Service Information ........................................................................................vi
Newport Corporation RMA Procedures .........................................................vi
Packaging........................................................................................................vi
1.0 Introduction ............................................................................................. 1
1.1 Scope of the Manual.........................................................................................................1
1.2 Definitions and Symbols ..................................................................................................1
1.2.1 General Warning or Caution............................................................................1
1.2.2 Electric Shock..................................................................................................2
1.2.3 European Union CE Mark ...............................................................................2
1.2.4 “ON” Symbol ..................................................................................................2
1.2.5 “OFF” Symbol.................................................................................................2
1.3 Warnings and Cautions.....................................................................................................2
1.4 General Warnings and Cautions .......................................................................................3
2.0 Getting Started ........................................................................................ 4
2.1 Unpacking and Handling ..................................................................................................4
2.2 Inspection for Damage......................................................................................................4
2.3 Packing List ......................................................................................................................4
2.4 System Setup ....................................................................................................................5
2.4.1 Installing Driver cards .....................................................................................5
2.4.2 Power ON ........................................................................................................6
2.5 Connecting to the XPS .....................................................................................................6
2.5.1 Direct Connection to the XPS controller .........................................................6
2.5.2 Ethernet Card Address Settings .......................................................................7
2.5.3 Stages Configuration for Newport Stages (Auto-Configuration) ....................8
2.5.4 Using Stages ....................................................................................................8
3.0 XPS Controller/Driver Documentation................................................. 9
Service Form ........................................................................................................ 11
iii EDH0205En1051 – 10/17

XPS Motion Controller/Driver Quick Start
EDH0205En1051 – 10/17 iv

XPS Motion Controller/Driver Quick Start
Preface
Confidentiality & Proprietary Rights
Reservation of Title
The Newport Programs and all materials furnished or produced in connection with them
(“Related Materials”) contain trade secrets of Newport and are for use only in the
manner expressly permitted. Newport claims and reserves all rights and benefits
afforded under law in the Programs provided by Newport Corporation.
Newport shall retain full ownership of Intellectual Property Rights in and to all
development, process, align or assembly technologies developed and other derivative
work that may be developed by Newport. Customer shall not challenge, or cause any
third party to challenge, the rights of Newport.
Preservation of Secrecy and Confidentiality and Restrictions to Access
Customer shall protect the Newport Programs and Related Materials as trade secrets of
Newport, and shall devote its best efforts to ensure that all its personnel protect the
Newport Programs as trade secrets of Newport Corporation. Customer shall not at any
time disclose Newport's trade secrets to any other person, firm, organization, or
employee that does not need (consistent with Customer's right of use hereunder) to
obtain access to the Newport Programs and Related Materials. These restrictions shall
not apply to information (1) generally known to the public or obtainable from public
sources; (2) readily apparent from the keyboard operations, visual display, or output
reports of the Programs; (3) previously in the possession of Customer or subsequently
developed or acquired without reliance on the Newport Programs; or (4) approved by
Newport for release without restriction.
Sales, Tech Support & Service
North America & Asia
Newport Corporation
1791 Deere Ave.
Irvine, CA 92606, USA
Sales
Tel.: [phone]
e-mail: sale[email protected]m
Technical Support
Tel.: [phone]
e-mail: tec[email protected]m
Service, RMAs & Returns
Tel.: [phone]
e-mail: [email protected]
Europe
MICRO-CONTROLE Spectra-Physics S.A.S
9, rue du Bois Sauvage
91055 Évry CEDEX
France
Sales France
Tel.: [phone]
e-mail: [email protected]
Sales Germany
Tel.: [phone] / 708 – 0
e-mail: [e-mail]
Sales UK
Tel.: [phone]
e-mail: [e-mail]
Technical Support
e-mail: [e-mail]
Service & Returns
Tel.: [phone]
v EDH0205En1051 – 10/17

XPS Motion Controller/Driver Quick Start
Service Information
The user should not attempt any maintenance or service of the XPS Series
Controller/Driver system beyond the procedures outlined in this manual. Any problem
that cannot be resolved should be referred to Newport Corporation. When calling
Newport regarding a problem, please provide the Tech Support representative with the
following information:
•Your contact information.
•System serial number or original order number.
•Description of problem.
•Environment in which the system is used.
•State of the system before the problem.
•Frequency and repeatability of problem.
•Can the product continue to operate with this problem?
•Can you identify anything that may have caused the problem?
Newport Corporation RMA Procedures
Any XPS Series Controller/Driver being returned to Newport must have been assigned
an RMA number by Newport. Assignment of the RMA requires the item serial number.
Packaging
XPS Series Controller/Driver being returned under an RMA must be securely packaged
for shipment. If possible, re-use the original factory packaging.
EDH0205En1051 – 10/17 vi

XPS Motion Controller/Driver Quick Start
1.0 Introduction
1.1 Scope of the Manual
The XPS is an extremely high-performance, easy to use, integrated motion
controller/driver offering high-speed communication through 10/100 Base-T Ethernet,
outstanding trajectory accuracy and powerful programming functionality. It combines
user-friendly web interfaces with advanced trajectory and synchronization features to
precisely control from the most basic to the most complex motion sequences. Multiple
digital and analog I/O's, triggers and supplemental encoder inputs provide users with
additional data acquisition, synchronization and control features that can improve the
most demanding motion applications.
To maximize the value of the XPS Controller/Driver system, it is important that users
become thoroughly familiar with available documentation:
The XPS Quick Start and XPS User’s Manual are delivered with the controller.
XPS User’s Manual, TCL Manual, Software Drivers Manual and Stage Configuration
Manual are PDF files accessible from the XPS web site.
DLLs and corresponding sources are available from the controller disk in the folder
Public/Drivers/DLL. DLLs can also be downloaded through FTP.
LabView VIs with examples are also available on the controller disk in the folder
Public/Drivers/LabView. They can be downloaded through FTP.
The Quick Start is the getting-started part of the system. It serves as an introduction
and as a reference. It includes:
1. Unpacking and Handling
2. Inspection for Damage
3. Packing List
4. System Setup
5. Connecting the XPS
1.2 Definitions and Symbols
The following terms and symbols are used in this documentation and also appear on the
XPS Series Controller/Driver where safety-related issues occur.
1.2.1 General Warning or Caution
Figure 1: General Warning or Caution Symbol.
Universal High
-Performance
Motion Controller/Driver
XPS Controller
1 EDH0205En1051 – 10/17

XPS Motion Controller/Driver Quick Start
The Exclamation Symbol in Figure 1 may appear in Warning and Caution tables in this
document. This symbol designates an area where personal injury or damage to the
equipment is possible.
1.2.2 Electric Shock
Figure 2: Electrical Shock Symbol.
The Electrical Shock Symbol in Figure 2 may appear on labels affixed to the XPS
Series Controller/Driver. This symbol indicates a hazard arising from dangerous
voltage. Any mishandling could result in damage to the equipment, personal injury, or
death.
1.2.3 European Union CE Mark
Figure 3: CE Mark.
The presence of the CE Mark on Newport Corporation equipment means that it has
been designed, tested and certified as complying with all applicable European Union
(CE) regulations and recommendations.
1.2.4 “ON” Symbol
Figure 4: “ON” Symbol.
The “ON” Symbol in Figure 4 appears on the power switch of the XPS Series
Controller/Driver. This symbol represents the “Power On” condition.
1.2.5 “OFF”Symbol
Figure 5: “OFF” Symbol.
The “Off” Symbol in Figure 5 appears on the power switch of the XPS Series
Controller/Driver. This symbol represents the “Power Off” condition.
1.3 Warnings and Cautions
The following are definitions of the Warnings, Cautions and Notes that may be used in
this manual to call attention to important information regarding personal safety, safety
and preservation of the equipment, or important tips.
WARNING
Situation has the potential to cause bodily harm or death.
EDH0205En1051 – 10/17 2

XPS Motion Controller/Driver Quick Start
CAUTION
Situation has the potential to cause damage to property or
equipment.
NOTE
Additional information the user or operator should consider.
1.4 General Warnings and Cautions
The following general safety precautions must be observed during all phases of
operation of this equipment.
Failure to comply with these precautions or with specific warnings elsewhere in this
manual violates safety standards of design, manufacture, and intended use of the
equipment.
•Heed all warnings on the unit and in the operating instructions.
•To prevent damage to the equipment, read the instructions in this manual for
selection of the proper input voltage.
•Only plug the Controller/Driver unit into a grounded power outlet.
•Assure that the equipment is properly grounded to earth ground through the
grounding lead of the AC power connector.
•Route power cords and cables where they are not likely to be damaged.
•The system must be installed in such a way that power switch and power inlet
remains accessible to the user.
•Disconnect or do not plug in the AC power cord in the following circumstances:
–If the AC power cord or any other attached cables are frayed or damaged.
–If the power plug or receptacle is damaged.
–If the unit is exposed to rain or excessive moisture, or liquids are spilled on it.
–If the unit has been dropped or the case is damaged.
•If the user suspects service or repair is required.
•Keep air vents free of dirt and dust.
•Keep liquids away from unit.
•Do not expose equipment to excessive moisture (>85% humidity).
•Do not operate this equipment in an explosive atmosphere.
•Disconnect power before cleaning the Controller/Driver unit. Do not use liquid or
aerosol cleaners.
•Do not open the XPS Controller/Driver stand-alone motion controller. There are no
user-serviceable parts inside the XPS Controller/Driver.
•Return equipment to Newport Corporation for service and repair.
•Dangerous voltages associated with the 100–240 VAC power supply are present
inside Controller/Driver unit. To avoid injury, do not touch exposed connections or
components while power is on.
•Follow precautions for static-sensitive devices when handling electronic circuits.
3 EDH0205En1051 – 10/17

XPS Motion Controller/Driver Quick Start
2.0 Getting Started
2.1 Unpacking and Handling
It is recommended that the XPS Controller/Driver be unpacked in your lab or work site
rather than at the receiving dock. Unpack the system carefully; small parts and cables
are included with the equipment. Inspect the box carefully for loose parts before
disposing of the packaging. You are urged to save the packaging material in case you
need to ship your equipment.
2.2 Inspection for Damage
XPS Controller/Driver has been carefully packaged at the factory to minimize the
possibility of damage during shipping. Inspect the box for external signs of damage or
mishandling. Inspect the contents for damage. If there is visible damage to the
equipment upon receipt, inform the shipping company and Newport Corporation
immediately.
WARNING
Do not attempt to operate this equipment if there is evidence of
shipping damage or you suspect the unit is damaged. Damaged
equipment may present additional hazards to you. Contact Newport
technical support for advice before attempting to plug in and operate
damaged equipment.
2.3 Packing List
Included with each XPS controller are the following items:
•User’s Manual and Motion Tutorial.
•XPS controller.
•Cross-over cable, gray, 3 meters.
•Straight-through cable, black, 5 meters.
•Power cord.
•Rack mount ears and handles.
If there are missing hardware or have questions about the hardware that were received,
please contact Newport.
CAUTION
Before operating the XPS controller, please read chapter 1.0 very
carefully.
EDH0205En1051 – 10/17 4

XPS Motion Controller/Driver Quick Start
2.4 System Setup
This section guides the user through the proper set-up of the motion control system. If
not already done, carefully unpack and visually inspect the controller and stages for any
damage. Place all components on a flat and clean surface.
CAUTION
No cables should be connected to the controller at this point!
First, the controller must be configured properly before stages can be connected.
2.4.1 Installing Driver cards
Figure 6: Installing Driver cards.
Due to the high power available in the XPS controller (300 W for the CPU and 500 W
for the drives), ventilation is very important.
To ensure a good level of heat dissipation, the following rules must be followed:
1. It is strictly forbidden to use the XPS controller without the cover properly mounted
on the chassis.
2. Driver boards must be inserted from the right (driver 1) to the left (driver 8) when
looking at the controller from the back.
3. If 8 boards or less are used, the remaining slots must disabled with the appropriate
covers that were delivered with the controller.
4. The surrounding ventilation holes at the sides and back of the XPS rack must be free
from obstructions that prevent free flow of air.
5 EDH0205En1051 – 10/17

XPS Motion Controller/Driver Quick Start
2.4.2 Power ON
•Plug the AC line cord supplied with the XPS into the AC power receptacle on the
rear panel.
•Plug the AC line cord into the AC wall-outlet. Turn the Main Power Switch to ON
(located on the Rear Panel).
•The system must be installed in such a way that power switch and power connector
remain accessible by the user.
•After the main power is switched on, the LED on the front panel of the XPS will
turn green.
•There is an initial beep when the switch is pushed. Once the controller completes
booting up there is a second beep. It can take 1 to 2 minutes for the controller to
boot up.
•There is also a STOP ALL button on the front panel that is used for an Emergency
Stop of the system and will shut down all the motors.
2.5 Connecting to the XPS
The Newport’s XPS Controller/Driver is a multi-axis motion controller system that is
based on a high performance 10/100 base T Ethernet connection using CAT5 cable.
The controller can be connected in 2 different ways:
1. Direct connection-PC to XPS through a cross over cable (gray).
2. Corporate Network connection – requires input from Network Administrator
(black).
Two cables are provided with the motion controller:
•Cross-over cable – used when connecting XPS directly to a PC.
•Straight Ethernet cable – used when connecting XPS through an intranet.
NOTE
For Network connection, please refer to the XPS User’s manual.
2.5.1 Direct Connection to the XPS controller
Plug a cross-over Ethernet cable (gray) between your computer and the HOST
connector at the back of the XPS mainframe.
Switch on the controller and wait while the controller is booting (nearly 60 s).
EDH0205En1051 – 10/17 6

XPS Motion Controller/Driver Quick Start
2.5.2 Ethernet Card Address Settings
In order to be able to communicate with the controller, you must set your Ethernet card
in the following way (this procedure is for the Windows XP operating system):
1. Start Button > Control Panel > Network Connections.
2. Right Click on Local Area Connection Icon and select Properties.
3. Highlight Internet Protocol (TCP/IP) and click on Properties.
4. Type the following IP address and Subnet Mask as shown in the next window.
5. Click “OK”.
7 EDH0205En1051 – 10/17

XPS Motion Controller/Driver Quick Start
2.5.3 Stages Configuration for Newport Stages (Auto-Configuration)
For Non Newport stages, please refer to the XPS
User’s Manual.
1. Open your web browser (as Internet
Explorer) and connect to:
http://192.168.0.254
The welcome web page appears. Fill the
following fields:
Name: Administrator
Password: Administrator
Rights: Administrator
2. Click “ENTER”.
3. Click on AUTO-CONFIGURATION menu
then “Generate Configuration files” button.
The XPS controller is now rebooting, you can
close the web browser.
2.5.4 Using Stages
1. Open your web browser (as Internet
Explorer) and connect to:
http://192.168.0.254
Fill the following fields:
Name: Anonymous
Password: Anonymous
Rights: User
2. Click “ENTER”.
3. Click on the FRONT PANEL menu then
Move submenu. Use the “Action” button to
initialize and home each group. For any
motion, type the absolute value and click on
the corresponding “Go” button.
Now you have done the first step and you are
ready to use more complex features with the XPS
controller.
To achieve this, please read the XPS User’s
Manual.
EDH0205En1051 – 10/17 8

XPS Motion Controller/Driver Quick Start
3.0 XPS Controller/Driver Documentation
To maximize the value of the XPS Controller/Driver system, it is important that users
become thoroughly familiar with available documentation:
The User’s Manual & Motion Tutorial
The first part of this book is the getting-started part of the system. This handy
introduction can be considered as a reference manual. It includes:
•System overview (Hardware, front and rear panels descriptions, Ethernet
connection, programming).
•Getting started guide (unpacking, inspection, system set up, connection,
configuration).
•Software tools description (web site interface).
•FTP (File Transfer Protocol) Connection.
•Maintenance and service (cleaning, service, troubleshooting).
The Motion Tutorial
The other part of the book provides an exhaustive overview of the XPS architecture, and
a complete description of its features and capabilities. It is educational and it contains
the following sections:
•Explanations of XPS architecture (state diagrams, motion groups, units).
•Motion modes (move, jog, master slave, analog tracking).
•Trajectories (line-arc, splines, PVT, conventions, mathematical explanations).
•Compensation (backlash, linear error correction, positioner/XY/XYZ mapping).
•Event triggers (event, actions, examples).
•Data gathering (internal and external).
•Triggers (position compare output, position capture).
•Control loops (XPS servo loops, filtering and limitation, feed forward loops and
servo tuning).
•Analog encoder calibration.
•Introduction to XPS Programming.
•Appendices: hardware, general I/O description, power inhibit connector, GPIO
connectors, PCO connector, motor driver boards pinning diagrams, analog encoder
connector, trigger in connector.
The Programmer’s Manual
This book is the general programmer’s guide for the experienced user. It provides
explanations of all functions and a list of all API’s with complete syntax (TCL and DLL
prototypes), parameters, errors, and short descriptions. It refers to the motion tutorial for
more thorough explanations on some features. It details:
•TCP/IP communication explanations and functions.
•Firmware features and list of API’s by groups: General features, Positioners, Single
Axis groups, XY groups, XYZ groups, Multiple Axes groups, analog and digital
I/O’s, gathering, events and actions, TCL programming, version).
•Examples of motion processes.
9 EDH0205En1051 – 10/17

XPS Motion Controller/Driver Quick Start
The Software Drivers Manual
This book provides all information about software tools and drivers shipped with the
XPS:
•Visual C++ / Visual Basic documentation (deliverable with DLL).
•LabView VI documentation (deliverable with VI).
•Matlab documentation (deliverable with m files).
The TCL Manual
This book provides a short introduction to TCL, describes all TCL commands supported
by the XPS and contains TCL program examples.
In order to provide user’s access to the most actual documentation, the Programmer’s
Manual, the Software Drivers Manual and the TCL Manual are only supplied as
software copies. They can get accessed from the XPS web site or downloaded from the
XPS controller via FTP.
EDH0205En1051 – 10/17 10

XPS Motion Controller/Driver Quick Start
Service Form
Your Local Representative
Tel.: __________________
Fax:___________________
Name: _________________________________________________ Return authorization #: ____________________________________
Company:_______________________________________________ (Please obtain prior to return of item)
Address:________________________________________________ Date: __________________________________________________
Country:________________________________________________ Phone Number: __________________________________________
P.O. Number:____________________________________________ Fax Number: ____________________________________________
Item(s) Being Returned:____________________________________
Model#: ________________________________________________ Serial #: ________________________________________________
Description: ________________________________________________________________________________________________________
Reasons of return of goods (please list any specific problems): ________________________________________________________________
__________________________________________________________________________________________________________________
__________________________________________________________________________________________________________________
__________________________________________________________________________________________________________________
__________________________________________________________________________________________________________________
__________________________________________________________________________________________________________________
__________________________________________________________________________________________________________________
__________________________________________________________________________________________________________________
__________________________________________________________________________________________________________________
__________________________________________________________________________________________________________________
__________________________________________________________________________________________________________________
__________________________________________________________________________________________________________________
__________________________________________________________________________________________________________________
__________________________________________________________________________________________________________________
__________________________________________________________________________________________________________________
__________________________________________________________________________________________________________________
__________________________________________________________________________________________________________________
__________________________________________________________________________________________________________________
__________________________________________________________________________________________________________________
__________________________________________________________________________________________________________________
__________________________________________________________________________________________________________________
__________________________________________________________________________________________________________________
__________________________________________________________________________________________________________________
__________________________________________________________________________________________________________________
__________________________________________________________________________________________________________________
__________________________________________________________________________________________________________________
__________________________________________________________________________________________________________________
__________________________________________________________________________________________________________________
__________________________________________________________________________________________________________________
11 EDH0205En1051 – 10/17

North America & Asia
Newport Corporation
1791 Deere Ave.
Irvine, CA 92606, USA
Sales
Tel.: [phone]
e-mail: [e-mail]
Technical Support
Tel.: [phone]
e-mail: [e-mail]
Service, RMAs & Returns
Tel.: [phone]
e-mail: [e-mail]
Europe
MICRO-CONTROLE Spectra-Physics S.A.S
9, rue du Bois Sauvage
91055 Évry CEDEX
France
Sales
Tel.: [phone]
e-mail: [e-mail]
Technical Support
e-mail: [e-mail]
Service & Returns
Tel.: [phone]
Visit Newport Online at:
www.newport.com