Newport XPS-Q8 User manual

XPS-Q8
U
ser’s Manual,
Software Tools
and
Tutorial
V1.4
.x
Universal High-Performance
Motion Controller/Driver

XPS-Q8 Universal High-Performance Motion Controller/Driver
Warranty
Newport Corporation warrants that this product will be free from defects in material and
workmanship and will comply with Newport’s published specifications at the time of
sale for a period of one year from date of shipment. If found to be defective during the
warranty period, the product will either be repaired or replaced at Newport's option.
To exercise this warranty, write or call your local Newport office or representative, or
contact Newport headquarters in Irvine, California. You will be given prompt assistance
and return instructions. Send the product, freight prepaid, to the indicated service
facility. Repairs will be made and the instrument returned freight prepaid. Repaired
products are warranted for the remainder of the original warranty period or 90 days,
whichever comes first.
Limitation of Warranty
The above warranties do not apply to products which have been repaired or modified
without Newport’s written approval, or products subjected to unusual physical, thermal
or electrical stress, improper installation, misuse, abuse, accident or negligence in use,
storage, transportation or handling. This warranty also does not apply to fuses, batteries,
or damage from battery leakage.
THIS WARRANTY IS IN LIEU OF ALL OTHER WARRANTIES, EXPRESSED OR
IMPLIED, INCLUDING ANY IMPLIED WARRANTY OF MERCHANTABILITY
OR FITNESS FOR A PARTICULAR USE. NEWPORT CORPORATION SHALL
NOT BE LIABLE FOR ANY INDIRECT, SPECIAL, OR CONSEQUENTIAL
DAMAGES RESULTING FROM THE PURCHASE OR USE OF ITS PRODUCTS.
©2017 by Newport Corporation, Irvine, CA. All rights reserved.
Original instructions.
No part of this document may be reproduced or copied without the prior written
approval of Newport Corporation. This document is provided for information only, and
product specifications are subject to change without notice. Any change will be
reflected in future publishings.
XPSDocumentation V1.4.x (EDH0301En1060 — 10/17)ii

XPS-Q8 Universal High-Performance Motion Controller/Driver
Table of Contents
Waranty ............................................................................................................................ii
EU Declaration of Conformity .........................................................................................x
Preface.............................................................................................................................xi
User’s Manual
1.0 Introduction .................................................................................................. 1
1.1 Scope of the Manual ................................................................................................................1
1.2 Definitions and Symbols..........................................................................................................3
1.2.1 General Warning or Caution ................................................................................3
1.2.2 Electric Shock......................................................................................................3
1.2.3 European Union CE Mark....................................................................................3
1.2.4 “ON” Symbol.......................................................................................................3
1.2.5 “OFF” Symbol .....................................................................................................3
1.3 Warnings and Cautions............................................................................................................4
1.4 General Warnings and Cautions ..............................................................................................4
2.0 System Overview........................................................................................... 6
2.1 Specifications...........................................................................................................................6
2.2 Drive Options ..........................................................................................................................7
2.3 Compatible Newport Positioners and Drive Power Consumption...........................................8
2.4 XPS Hardware Overview.........................................................................................................9
2.5 Front Panel Description ...........................................................................................................9
2.6 Rear Panel Description ..........................................................................................................10
2.6.1 Axis Connectors (AXIS 1 – AXIS 8).................................................................10
2.7 Ethernet Configuration ..........................................................................................................11
2.7.1 Communication Protocols..................................................................................11
2.7.2 Addressing .........................................................................................................12
2.8 Sockets, Multitasking and Multi-user Applications...............................................................12
2.9 Programming with TCL.........................................................................................................12
iii XPSDocumentation V1.4.x (EDH0301En1060 — 10/17)

XPS-Q8 Universal High-Performance Motion Controller/Driver
3.0 Getting Started............................................................................................ 14
3.1 Unpacking and Handling .......................................................................................................14
3.2 Inspection for Damage...........................................................................................................14
3.3 Packing List ...........................................................................................................................14
3.4 System Setup .........................................................................................................................14
3.4.1 Installing Driver cards........................................................................................15
3.4.2 Power ON ..........................................................................................................15
3.5 Connecting to the XPS...........................................................................................................16
3.5.1 Straight through cables (black) ..........................................................................16
3.5.2 Cross-over cables (gray) ....................................................................................16
3.5.3 Direct Connection to the XPS Controller...........................................................17
3.5.4 Connecting the XPS to a Corporate Network using Static IP Configuration.....19
3.5.5 Configuring the XPS for Connection to a Corporate Network Using Dynamic IP
Configuration.................................................................................................21
3.5.6 Recovering a lost IP configuration.....................................................................24
3.6 Testing your XPS-PC Connection and Communication........................................................26
3.7 Connecting the Stages............................................................................................................27
3.8 Configuring the Controller.....................................................................................................28
3.8.1 Auto Configuration ............................................................................................29
3.8.2 Manual Configuration for Newport Positioners.................................................31
3.8.3 Manual Configuration for non Newport stages..................................................35
3.9 System Shut-Down ................................................................................................................35
Software Tools
4.0 Software Tools............................................................................................. 36
4.1 Software Tools Overview ......................................................................................................36
4.2 CONTROLLER CONFIGURATION – Users Management.................................................37
4.3 CONTROLLER CONFIGURATION – IP Management ......................................................38
4.4 CONTROLLER CONFIGURATION – General...................................................................38
4.5 SYSTEM – Error file display ................................................................................................39
4.6 SYSTEM – Last error file display .........................................................................................39
4.7 SYSTEM – Auto Configuration ............................................................................................40
4.8 SYSTEM – Manual Configuration ........................................................................................40
4.9 SYSTEM – Manual Configuration – Gantries (Secondary Positioners)................................44
4.9.1 Home search of gantries.....................................................................................45
4.9.2 Gantries with linear motors................................................................................46
4.9.3 Gantries with linear motors and variable force ratio..........................................47
4.10 STAGE – Add from Data Base............................................................................................49
XPSDocumentation V1.4.x (EDH0301En1060 — 10/17)iv

XPS-Q8 Universal High-Performance Motion Controller/Driver
4.11 STAGE – Modify ................................................................................................................50
4.12 FRONT PANEL – Move .....................................................................................................52
4.13 FRONT PANEL – Jog.........................................................................................................53
4.14 FRONT PANEL – Spindle ..................................................................................................53
4.15 FRONT PANEL – I/O View................................................................................................54
4.16 FRONT PANEL – I/O Set ...................................................................................................54
4.17 FRONT PANEL – Positioner Errors ...................................................................................55
4.18 FRONT PANEL – Hardware Status ....................................................................................55
4.19 FRONT PANEL – Driver Status .........................................................................................56
4.20 TERMINAL.........................................................................................................................56
4.21 TUNING – Auto-Scaling.....................................................................................................59
4.22 TUNING – Auto-Tuning .....................................................................................................60
4.23 FUNCTIONAL TESTS .......................................................................................................63
4.24 FTP (File Transfer Protocol) Connection ............................................................................63
5.0 Maintenance and Service ........................................................................... 65
5.1 Enclosure Cleaning................................................................................................................65
5.2 Obtaining Service ..................................................................................................................65
5.3 Troubleshooting.....................................................................................................................65
5.4 Updating the Firmware Version of Your XPS Controller .....................................................66
Motion Tutorial
6.0 XPS Architecture ........................................................................................ 67
6.1 Introduction ...........................................................................................................................67
6.2 State Diagrams.......................................................................................................................68
6.3 Motion Groups.......................................................................................................................70
6.3.1 Specific SingleAxis Group Features ..................................................................71
6.3.2 Specific Spindle Group Features........................................................................71
6.3.3 Specific XY Group Features..............................................................................71
6.3.4 Specific XYZ Group Features............................................................................71
6.3.5 Specific MultipleAxes Features .........................................................................71
6.4 Native Units...........................................................................................................................71
7.0 Motion.......................................................................................................... 73
7.1 Motion Profiles ......................................................................................................................73
7.2 Home Search..........................................................................................................................75
7.3 Referencing State...................................................................................................................78
7.3.1 Move on sensor events.......................................................................................79
v XPSDocumentation V1.4.x (EDH0301En1060 — 10/17)

XPS-Q8 Universal High-Performance Motion Controller/Driver
7.3.2 Moves of Certain Displacements .......................................................................80
7.3.3 Position Counter Resets .....................................................................................80
7.3.4 State Diagram ....................................................................................................81
7.3.5 Example: MechanicalZeroAndIndexHomeSearch.............................................81
7.4 Move......................................................................................................................................81
7.5 Motion Done..........................................................................................................................83
7.6 JOG........................................................................................................................................85
7.7 Master Slave ..........................................................................................................................86
7.8 Analog Tracking ....................................................................................................................87
7.8.1 Analog Position Tracking ..................................................................................88
7.8.2 Analog Velocity Tracking..................................................................................88
8.0 Trajectories ................................................................................................. 90
8.1 Line-Arc Trajectories.............................................................................................................90
8.1.1 Trajectory Terminology .....................................................................................90
8.1.2 Trajectory Conventions......................................................................................91
8.1.3 Geometric Conventions .....................................................................................91
8.1.4 Defining Line-Arc Trajectory Elements ............................................................91
8.1.5 Define Lines.......................................................................................................92
8.1.6 Define Arcs........................................................................................................93
8.1.7 Trajectory File Description ................................................................................93
8.1.8 Trajectory File Examples...................................................................................93
8.1.9 Trajectory Verification and Execution...............................................................94
8.1.10 Examples of the Use of the Functions..............................................................95
8.2 Splines ...................................................................................................................................96
8.2.1 Trajectory Terminology .....................................................................................96
8.2.2 Trajectory Conventions......................................................................................96
8.2.3 Geometric Conventions .....................................................................................96
8.2.4 Catmull-Rom Interpolating Splines ...................................................................97
8.2.5 Trajectory Elements Arc Length Calculation.....................................................97
8.2.6 Trajectory File Description ................................................................................98
8.2.7 Trajectory File Example ....................................................................................98
8.2.8 Spline Trajectory Verification and Execution..................................................100
8.2.9 Examples..........................................................................................................101
8.3 PVT Trajectories..................................................................................................................101
8.3.1 Trajectory Terminology ...................................................................................101
8.3.2 Trajectory Conventions....................................................................................101
8.3.3 Geometric Conventions ...................................................................................102
8.3.4 PVT Interpolation ............................................................................................102
8.3.5 Influence of the Element Output Velocity to the Trajectory............................103
8.3.6 Trajectory File Description ..............................................................................104
8.3.7 Trajectory File Example ..................................................................................105
8.3.8 PVT Trajectory Verification and Execution ....................................................106
8.3.9 Examples of the Use of the functions ..............................................................107
XPSDocumentation V1.4.x (EDH0301En1060 — 10/17)vi

XPS-Q8 Universal High-Performance Motion Controller/Driver
9.0 Emergency Brake and Emergency Stop Cases ...................................... 108
10.0 Compensation.......................................................................................... 111
10.1 Backlash Compensation.....................................................................................................112
10.2 Linear Error Correction .....................................................................................................113
10.3 Positioner Mapping............................................................................................................113
10.4 XY Mapping ......................................................................................................................116
10.5 XYZ Mapping....................................................................................................................118
10.6 “Yaw” Mapping (PP Firmware Version Only)..................................................................124
10.7 “Theta” Encoder and XY Correction.................................................................................127
11.0 Event Triggers......................................................................................... 128
11.1 Events ................................................................................................................................129
11.2 Actions...............................................................................................................................137
11.3 Functions ...........................................................................................................................142
11.4 Examples ...........................................................................................................................143
12.0 Data Gathering ....................................................................................... 147
12.1 Time-Based (Internal) Data Gathering ..............................................................................148
12.2 Event-Based (Internal) Data Gathering..............................................................................150
12.3 Function-Based (Internal) Data Gathering.........................................................................153
12.4 Trigger-Based (External) Data Gathering..........................................................................153
13.0 Output Triggers ...................................................................................... 155
13.1 Triggers on Line-Arc Trajectories .....................................................................................155
13.2 Triggers on PVT Trajectories ............................................................................................157
13.3 Distance, Time Spaced Pulses or AquadB Position Compare ...........................................158
13.3.1 Position compare settings and limits of use ...................................................158
13.3.2 Even Distance Spaced Pulses Position Compare ...........................................159
13.3.3 Compensated Position Compare ....................................................................163
13.3.4 Time Spaced Pulses (Time Flasher)...............................................................166
13.3.5 AquadB Signals on PCO Connector ..............................................................168
14.0 Control Loops ......................................................................................... 171
14.1 XPS Servo Loops...............................................................................................................171
14.1.1 Servo structure and Basics .............................................................................171
14.1.2 XPS PIDFF Architecture ...............................................................................173
14.2 Filtering and Limitation .....................................................................................................177
14.3 Feed Forward Loops and Servo Tuning.............................................................................177
14.3.1 Corrector = PIDFFVelocity ...........................................................................177
14.3.2 Corrector = PIDFFAcceleration.....................................................................179
14.3.3 Corrector = PIDDual FFVoltage....................................................................182
14.3.4 Corrector = PIPosition ...................................................................................183
vii XPSDocumentation V1.4.x (EDH0301En1060 — 10/17)

XPS-Q8 Universal High-Performance Motion Controller/Driver
15.0 Analog Encoder Calibration.................................................................. 185
16.0 Excitation Signal..................................................................................... 190
16.1 Introduction........................................................................................................................190
16.2 How to Use the Excitation-Signal Function ......................................................................190
16.3 Group State Diagram .........................................................................................................191
16.4 Function Description..........................................................................................................191
17.0 Pre-Corrector Excitation Signal............................................................ 192
17.1 Description.........................................................................................................................192
17.2 Pre-corrector excitation signal wave forms .......................................................................192
17.3 Technical Implementation .................................................................................................194
17.3.1 Use case .........................................................................................................194
17.3.2 Implementation ..............................................................................................195
17.3.3 Group capsule state diagram modification.....................................................196
18.0 Introduction to XPS Programming....................................................... 197
18.1 TCL Generator...................................................................................................................198
18.2 LabVIEW...........................................................................................................................199
18.3 DLL Drivers.......................................................................................................................200
18.4 Running Processes in Parallel............................................................................................201
XPSDocumentation V1.4.x (EDH0301En1060 — 10/17)viii

XPS-Q8 Universal High-Performance Motion Controller/Driver
ix XPSDocumentation V1.4.x (EDH0301En1060 — 10/17)
Appendix
19.0Appendix A: Hardware....................................................................... 204
19.1Controller ........................................................................................................................... 204
19.2Rear Panel Connectors ....................................................................................................... 205
19.3Environmental Requirements............................................................................................. 205
20.0Appendix B: General I/O Description .................................................. 206
20.1Digital I/Os (All GPIO, Inhibit and Trigger In, and PCO Connectors) ............................... 206
20.1.1Digital Inputs ................................................................................................. 206
20.1.2Digital Outputs ............................................................................................... 207
20.2Digital Encoder Inputs (Driver Boards & DRV00) ........................................................... 207
20.3Digital Servitudes (Driver Boards, DRV00 & Analog Encoders Connectors) .................. 207
20.4Analog Encoder Inputs (Analog Encoder Connectors) ...................................................... 207
20.5Analog I/O (GPIO2 Connector) ......................................................................................... 208
20.5.1Analog Inputs ................................................................................................. 208
20.5.2Analog Outputs .............................................................................................. 208
21.0Appendix C: Power Inhibit Connector ................................................. 209
22.0Appendix D: GPIO Connectors ............................................................ 210
22.1GPIO1 Connector .............................................................................................................. 2 1 0 
22.2GPIO2 Connector .............................................................................................................. 2 1 0 
22.3GPIO3 Connector .............................................................................................................. 2 1 1 
22.4GPIO4 Connector .............................................................................................................. 2 1 1 
23.0Appendix E: PCO Connector ................................................................ 212
24.0Appendix F: Motor Driver Cards ......................................................... 213
24.1DC and Stepper Motor Driver XPS-DRV01 ...................................................................... 213
24.2Three phase AC brushless driver XPS-DRV02 ................................................................. 214
24.3DC Motor Driver XPS-DRV03 ......................................................................................... 215
24.4Pass-Through Board Connector (25-Pin D-Sub) XPS-DRV00 ......................................... 215
25.0Appendix G: Analog Encoder Connector ............................................ 216
26.0Appendix H: Trigger IN Connector ..................................................... 217
Service Form ...................................................................................................... 219

XPS-Q8 Universal High-Performance Motion Controller/Driver
EU Declaration of Conformity
XPSDocumentation V1.4.x (EDH0301En1060 — 10/17)x

XPS-Q8 Universal High-Performance Motion Controller/Driver
Preface
Confidentiality & Proprietary Rights
Reservation of Title
The Newport Programs and all materials furnished or produced in connection with them
(“Related Materials”) contain trade secrets of Newport and are for use only in the
manner expressly permitted. Newport claims and reserves all rights and benefits
afforded under law in the Programs provided by Newport Corporation.
Newport shall retain full ownership of Intellectual Property Rights in and to all
development, process, align or assembly technologies developed and other derivative
work that may be developed by Newport. Customer shall not challenge, or cause any
third party to challenge, the rights of Newport.
Preservation of Secrecy and Confidentiality and Restrictions to Access
Customer shall protect the Newport Programs and Related Materials as trade secrets of
Newport, and shall devote its best efforts to ensure that all its personnel protect the
Newport Programs as trade secrets of Newport Corporation. Customer shall not at any
time disclose Newport's trade secrets to any other person, firm, organization, or
employee that does not need (consistent with Customer's right of use hereunder) to
obtain access to the Newport Programs and Related Materials. These restrictions shall
not apply to information (1) generally known to the public or obtainable from public
sources; (2) readily apparent from the keyboard operations, visual display, or output
reports of the Programs; (3) previously in the possession of Customer or subsequently
developed or acquired without reliance on the Newport Programs; or (4) approved by
Newport for release without restriction.
Sales, Tech Support & Service
North America & Asia
Newport Corporation
1791 Deere Ave.
Irvine, CA 92606, USA
Sales
Tel.: [phone]
e-mail: [e-mail]
Technical Support
Tel.: [phone]
e-mail: tec[email protected]m
Service, RMAs & Returns
Tel.: [phone]
e-mail: [email protected]
Europe
MICRO-CONTROLE Spectra-Physics S.A.S
9, rue du Bois Sauvage
91055 Évry CEDEX
France
Sales France
Tel.: [phone]
e-mail: [email protected]
Sales Germany
Tel.: [phone] / 708 – 0
e-mail: [e-mail]
Sales UK
Tel.: [phone]
e-mail: [e-mail]
Technical Support
e-mail: [e-mail]
Service & Returns
Tel.: [phone]
xi XPSDocumentation V1.4.x (EDH0301En1060 — 10/17)

XPS-Q8 Universal High-Performance Motion Controller/Driver
Service Information
The user should not attempt any maintenance or service of the XPS Series
Controller/Driver system beyond the procedures outlined in this manual. Any problem
that cannot be resolved should be referred to Newport Corporation. When calling
Newport regarding a problem, please provide the Tech Support representative with the
following information:
•Your contact information.
•System serial number or original order number.
•Description of problem.
•Environment in which the system is used.
•State of the system before the problem.
•Frequency and repeatability of problem.
•Can the product continue to operate with this problem?
•Can you identify anything that may have caused the problem?
Newport Corporation RMA Procedures
Any XPS Series Controller/Driver being returned to Newport must be assigned an RMA
number by Newport. Assignment of the RMA requires the item’s serial number.
Packaging
XPS Series Controller/Driver being returned under an RMA must be securely packaged
for shipment. If possible, re-use the original packaging.
XPSDocumentation V1.4.x (EDH0301En1060 — 10/17)xii

XPS-Q8 Controller User’s Manual
1.0 Introduction
1.1 Scope of the Manual
The XPS is an extremely high-performance, easy to use, integrated motion
controller/driver offering high-speed communication through 10/100 Base-T Ethernet,
outstanding trajectory accuracy and powerful programming functionality. It combines
user-friendly web interfaces with advanced trajectory and synchronization features to
precisely control from the most basic to the most complex motion sequences. Multiple
digital and analog I/O's, triggers and supplemental encoder inputs provide users with
additional data acquisition, synchronization and control features that can improve the
most demanding motion applications.
To maximize the value of the XPS Controller/Driver system, it is important that users
become thoroughly familiar with available documentation:
The XPS Quick Start and XPS User’s Manual are delivered as paper copies with the
controller.
The Programmer’s, TCL, Software Drivers and Stage Configuration manuals are PDF
files accessible from the XPS web site.
DLLs and corresponding sources are available from the controller disk in the folder
Public/Drivers/DLL. DLLs can also be downloaded through the FTP.
LabVIEW VIs with examples are also available from the controller disk in the folder
Public/Drivers/LabView. They can also be downloaded through FTP.
To connect through FTP, please see chapter 5: “FTP connection”.
The first part of this manual serves as an introduction and also as a reference. It
includes:
1. Introduction
2. System Overview
3. Getting Started Guide
User’s Manual
1 XPSDocumentation V1.4.x (EDH0301En1060 — 10/17)

XPS-Q8 Controller User’s Manual
The second part provides a detailed description of all software tools of the XPS
controller. It also includes an introduction to FTP connections and some general
guidelines for troubleshooting, maintenance and service:
4. Software Tools
5. FTP connection
6. Maintenance and Service
The third part provides an exhaustive description of the XPS architecture, its features
and capabilities. Complementing the programmer’s guide, this part is educational and is
organized by features starting with the basics and getting to the more advanced features.
It provides a complete list of descriptions of different features including:
7. XPS Architecture
8. Motion
9. Trajectories
10. Compensation
11. Event Triggers
12. Data Gathering
13. Triggers
14. Control Loops
15. Analog Encoder Calibration
16. Introduction to XPS programming
XPSDocumentation V1.4.x (EDH0301En1060 — 10/17)2

XPS-Q8 Controller User’s Manual
1.2 Definitions and Symbols
The following terms and symbols are used in this documentation and also appear on the
XPS Series Controller/Driver where safety-related issues occur.
1.2.1 General Warning or Caution
Figure 1: General Warning or Caution Symbol.
The Exclamation Symbol in Figure 1 may appear in Warning and Caution tables in this
document. This symbol designates an area where personal injury or damage to the
equipment is possible.
1.2.2 Electric Shock
Figure 2: Electrical Shock Symbol.
The Electrical Shock Symbol in Figure 2 may appear on labels affixed to the XPS
Series Controller/Driver. This symbol indicates a hazard arising from dangerous
voltages. Any mishandling could result in damage to the equipment, personal injury, or
even death.
1.2.3 European Union CE Mark
Figure 3: CE Mark.
The presence of the CE Mark on Newport Corporation equipment means that it has
been designed, tested and certified to comply with all current and applicable European
Union (CE) regulations and recommendations.
1.2.4 “ON” Symbol
Figure 4: “ON” Symbol.
The “ON” Symbol in Figure 4 appears on the power switch of the XPS Series
Controller/Driver. This symbol represents the “Power On” condition.
1.2.5 “OFF”Symbol
Figure 5: “OFF” Symbol.
The “Off” Symbol in Figure 5 appears on the power switch of the XPS Series
Controller/Driver. This symbol represents the “Power Off” condition.
3 XPSDocumentation V1.4.x (EDH0301En1060 — 10/17)

XPS-Q8 Controller User’s Manual
1.3 Warnings and Cautions
The following are definitions of the Warnings, Cautions and Notes that may be used in
this manual to call attention to important information regarding personal safety, safety
and preservation of the equipment, or important tips.
WARNING
Situation has the potential to cause bodily harm or death.
CAUTION
Situation has the potential to cause damage to property or
equipment.
WARNING
This product is equipped with a 3-wire grounding type plug. Any
interruption of the grounding connection can create an electric shock
hazard. If you are unable to insert the plug into your wall plug
receptacle, contact an electrician to perform the necessary alterations
to ensure that the green (green-yellow) wire is attached to earth
ground.
System earthing must be of type earthed neutral (TN-) as defined by
CEI60364.
NOTE
Additional information the user or operator should consider.
1.4 General Warnings and Cautions
The following general safety precautions must be observed during all phases of
operation of this equipment.
Failure to comply with these precautions or with specific warnings elsewhere in this
manual violates safety standards of design, manufacture, and the intended use of the
equipment.
•Heed all warnings on the unit and in the operating instructions.
•To prevent damage to the equipment, read the instructions in this manual for the
selection of the proper input voltage.
•Only plug the Controller/Driver unit into a grounded power outlet.
•Ensure that the equipment is properly grounded to earth ground through the
grounding lead of the AC power connector.
•Route power cords and cables where they are not likely to be damaged.
•Use Proper Power Cord
Use only the power cord specified for this product and certified for the country of
use.
•The system must be installed in such a way that the power switch and the power
connector remain accessible to the user.
•Disconnect or do not plug-in the AC power cord under the following conditions:
–If the AC power cord or any other attached cables are frayed or damaged.
–If the power plug or receptacle is damaged.
–If the unit is exposed to rain or excessive moisture, or liquids are spilled on it.
XPSDocumentation V1.4.x (EDH0301En1060 — 10/17)4

XPS-Q8 Controller User’s Manual
–If the unit has been dropped or the case is damaged.
–If the user suspects service or repair is required.
•Keep air vents free of dirt and dust and obstructions.
•Keep liquids away from unit.
•Do not expose equipment to excessive moisture (>85% humidity).
•Do not operate this equipment in an explosive atmosphere.
•Disconnect power before cleaning the Controller/Driver unit. Do not use liquid or
aerosol cleaners.
•Do not open the XPS Controller/Driver stand alone motion controller. There are no
user-serviceable parts inside the XPS Controller/Driver.
•Return equipment to Newport Corporation for service and repair.
•Dangerous voltages associated with the 100–240 VAC power supply are present
inside Controller/Driver unit. To avoid injury, do not touch exposed connections or
components while power is on.
•Follow precautions for static-sensitive devices when handling electronic circuits.
5 XPSDocumentation V1.4.x (EDH0301En1060 — 10/17)

XPS-Q8 Controller User’s Manual
2.0 System Overview
2.1 Specifications
Number of Axes •1 to 8 axes of stepper, DC brush, DC brushless motors or piezo-electric stacks using internal
drives
•
Other motion devices using external third-party drives
Communication Interfaces •Internet protocol TCP/IP
•One Ethernet 10/100 Base-T (RJ45 connector) with fixed IP address for local communication
•One Ethernet 10/100 Base-T (RJ45 connector) for networking, dynamic addressing with
DHCP and DNS
•Typically 0.3 ms from sending a tell position command to receiving the answer
•Optional XPS-RC remote control
Firmware Features •Powerful and intuitive, object oriented command language
•Native user defined units (no need to program in encoder counts)
•Real time execution of custom tasks using TCL scripts
•Multi-user capability
•Concept of sockets for parallel processes
•Distance spaced trigger output pulses, max. 2.5 MHz rate, programmable filter
•Time spaced trigger output pulses, 0.02 Hz to 2.5 MHz rate, 50 ns accuracy
•Trigger output on trajectories with 100 µs resolution
•Data gathering at up to 8 kHz rate, up to 1,000,000 data entries
•User-defined “actions at events” monitored by the controller autonomously at a rate of 8 kHz
•User-definable system referencing with hardware position latch of reference signal transition
and “set current position to value” capability
•Axis position or speed controlled by analog input
•Axis position, speed or acceleration copied to analog output
•Trajectory precheck function replying with travel requirement and max. possible speed
•Auto-tuning and auto-scaling
Motion •Jogging mode including on-the fly changes of speed and acceleration
•Synchronized point-to-point
•Spindle motion (continuous motion with periodic position reset)
•Gantry mode including XY gantries with variable load ratio
•Line-arc mode (linear and circular interpolation incl. continuous path contouring)
•Splines (Catmull-Rom type)
•PVT (complex trajectory based on position, velocity and time coordinates)
•Analog tracking (using analog input as position or velocity command)
•Master-slave including single master-multiple slaves and custom gear ratio
Compensation •Linear error, Backlash, positioner error mapping
•XY and XYZ error mapping
•All corrections are taken into account on the servo loop
Servo Rate
•8 kHz
Control Loop •Open loop, PI position, PIDFF velocity, PIDFF acceleration, PIDDualFF voltage
•Variable PID’s (PID values depending on distance to target position)
•Deadband threshold; Integration limit and integration time
•Derivative cut-off filter; 2 user-defined notch filters
XPSDocumentation V1.4.x (EDH0301En1060 — 10/17)6

XPS-Q8 Controller User’s Manual
I/O •30 TTL inputs and 30 TTL outputs (open-collector)
•4 synch. analog inputs ±10 V, 14 Bit
•4 synch. uncommitted analog outputs, 16 Bit
•Watchdog timer and remote interlock
Trigger In •Hardware latch of all positions and all analog I/O’s; 8 kHz max. frequency
•<50 ns latency on positions
•<100 µs time jitter on analog I/O’s
Trigger Out •One high-speed position compare output per axes that can be either configured for position
synchronized pulses or for time synchronized pulses : <50 ns accuracy/latency, 2.5 MHz max.
rate
Dedicated Inputs Per Axis •RS-422 differential inputs for A, B and I, Max. 25 MHz, over-velocity and quadrature error
detection
•1 Vpp analog encoder input up to x32768 interpolation used for servo; amplitude, phase and
offset correction; additional 2nd hardware interpolator used for synchronization; up to x200
interpolation
•Forward and reverse limit, home, error input
Dedicated Outputs Per Axis
(when using external drives)
2 channel 16-bit, ±10 V D/A
Drive enable, error output
Drive Capability
•Analog voltage, analog velocity, and analog acceleration (used with XPS-DRV01 and
XPS-DRV03 for DC brush motor control).
•Analog position (used with XPS-DRV01 for stepper motor control or with the XPS-DRVP1
for piezo control)
•Analog position (used with external drives for example 3rd party motors)
•Analog acceleration, sine acceleration and dual sine acceleration (used with XPS-DRV02 for
brushless motors control)
•Step and direction and +/- pulse mode for stepper motors (requires XPS-DRV00P and external
stepper motor driver)
•500 W @ 230 VAC and 425 W @ 115 VAC total available power
AC Power Requirements •100–240 VAC 60/50 Hz 10 A–5.5 A The controller should be connected to a power
installation that incorporates appropriate protection devices. Refer to the installation
requirements of your facility and local applicable Standards concerning the use of RCDs
(residual current device).
Dimensions (W x D x H)
•
19” – 4U, L: 508 mm
Weight
•15 kg max
2.2 Drive Options
The XPS controller is capable of driving up to 8 axes of most Newport positioners using
driver cards that slide through the back of the chassis. These factory-tested drives are
powered by an internal 500 W power supply, which is independent of the controller
power supply. When used with Newport ESP stages, the configuration of the driver
cards is easy using the auto-configuration utility software. Advanced users can also
manually develop their own configuration files optimized for specific applications.
The XPS-DRV01 is a software configurable PWM amplifier that is compatible with
most of Newport’s and other companies’ DC brush and stepper motor positioners.
The XPS-DRV01 motor driver supplies a maximum current of 3 Amps and 48 Volts. It
has the capability to drive bipolar stepper motors in microstep mode (sine/cosine
commutation) and DC brush motors in velocity mode, for motors with tachometer, or
voltage mode, for motors without tachometer. Programmable gains and a programmable
PWM switching frequency up to 300 kHz allow a very fine adjustment of the driver to
the motor. For added safety, a programmable over-current protection setting is also
available.
7 XPSDocumentation V1.4.x (EDH0301En1060 — 10/17)

XPS-Q8 Controller User’s Manual
The XPS-DRV02 is a software configurable PWM amplifier for 3-phase brushless
motors. It has been optimized for performance with XM, ILS-LM, IMS-LM linear
motor stages and RGV direct drive rotation stages. The XPS-DRV02 supplies a 100
kHz PWM output with a maximum output current of 5 A per phase and 44 Vpp. The
XPS-DRV02 requires 1 Vpp analog encoder input signals used also for motor
commutation. Motor initialization is done by a special routine measures the magnetic
position without the need for Hall or other sensors.
The XPS-DRV03 is a fully digital, programmable PWM-amplifier that has been
optimized for use with high-performance DC motors. The high switching frequency of
100 kHz and appropriate filter technologies minimize noise to enable ultra-precision
positioning in the nm-range. The XPS-DRV03 supplies a maximum current of 5 Amps
and 48 Volts. It is capable of driving DC motors in velocity mode (for motors with
tachometer), in voltage mode (for motors without tachometer), and in current mode (for
torque motors). All parameters are programmable in physical units (for instance the
bandwidth of the velocity loop). Furthermore, the XPS-DRV03 features individual
limits for the rms current and the peak current.
The XPS-DRVP1 is a programmable driver card for Newport's NanoPositioning line of
piezoelectric stack stages. This driver card has a range of -10 to 150 VDC with 30 mA
continuous. The drive features a 4 kHz update rate and resolution of 16 bits ADC and
DAC. It also accepts strain gage position feedback.
The XPS-DRV00 and XPS-DRV00P pass-through module can be used to pass control
signals to other external third-party amplifiers (drivers). By setting the controller’s dual
DAC output to either analog position, analog stepper position, analog velocity, analog
voltage or analog acceleration (including sine commutation), the XPS is capable of
controlling almost any motion device including 3rd party brushless motors and voice
coils.
In addition to conventional digital AquadB feedback encoder interface, the XPS
controller also features a high-performance analog encoder input (1 Vpp Heidenhain
standard) on each axis. An ultra-high resolution, very low noise, encoder signal
interpolator converts the sine-wave input to an exact position value with a signal
subdivision up to 32,768-fold. For example, when used with a scale with 4 µm signal
period the resolution can be as fine as 0.122 nm. This interpolator can be used for
accurate position feedback on the servo corrector of the system. An additional hardware
interpolator with 40 MHz clock frequency and programmable signal subdivision up to
200-fold is used for synchronization purposes. This fast interpolator latches the position
directly with less than 50 ns latency and provides a much higher level of precision for
synchronization than alternative time based systems. Unlike most high-resolution
multiplication devices, the XPS interpolators do not compromise positioning speed.
With a maximum input frequency ranging from 180 kHz to 400 kHz (depending on the
interpolation factor), the maximum speed of a stage with a 20 µm signal period scale
can be up to 3.6 m/s.
2.3 Compatible Newport Positioners and Drive Power Consumption
The list of all compatible Newport positioners and the corresponding drive module
needed is available from the Newport catalog or at www.newport.com
XPSDocumentation V1.4.x (EDH0301En1060 — 10/17)8