FORM NO. L-20191-F-1202
8
PARTS REPLACEMENT - FRICTION FACINGS
FMCBE 110-14, 130-19, 130-24, 7-28, 7-38, 8-38, AND 8-42
NOTE: If an Input Unit is installed on the FMCBE, it
mustberemovedbeforeservicingtheFMCBE.Remove
the Plug (Item 28) on Models 10-14, 130-19, and 130-
24, or Item 35 on Models 7-28, 7-38, 8-38, and 8-42)
and loosen the Set Screw (Item 27 on Models 110-14,
130-19,and 130-24, or Item 34 on Models7-28,7-38,8-
38 and 8-42) to release the FMCBE from the input unit
shaft (See Figure 7).
1. Remove the four Socket Head Cap Screws (Item 14
on Models 110-14, 130-19, and 130-24, or Item 8
on Models 7-28, 7-38, and 8-42) and separate the
two halves of the FMCBE (See Figure 7.
2. Remove the six old Flat Head Screws (Item 12) and
the first old split Friction Facing (Item 11) (See
Figure 8).
3. Align the holes in the Splined Disc (Item 9) with the
Flat Head Screws (Item 12) that secure the second
split Friction Facing (Item 11) (See Figure 8).
4. Remove the six old Flat Head Screws (Item 12) and
the second old Friction Facing (Item 11) (See
Figure 8).
5. Install the first new split Friction Facing (Item 11)
and the new Flat Head Screws (Item 12) (See
Figure 8).
6. Tighten the six New Flat Head Screws (Item 12) to
the recommended torque (See Table 1).
7. Install the second new split Friction Facing (Item
11) and new Flat Head Screws (Item 12) (See
Figure 8).
8. Tighten the six new Flat head Screws (Item 12) to
the recommended torque (See Table 1).
9. Apply a drop of Loctite®242 to the threads of the
Socket Head Cap Screws (Item 14 on Models 110-
14, 130-19, and 130-24, or Item 8 on Models 7-
28, 7-38, 8-38 and 8-42) (See Figure 7).
10. Install and tighten the four Socket Head Cap
Screws to the recommended torque (See Table 1).
Figure 7Figure 7
Figure 7Figure 7
Figure 7
Socket Head Cap Screw
(Item 8 or 14)
Plug
(Item 28 or 35)
Set Screw
(Item 27 or 34)
Figure 8Figure 8
Figure 8Figure 8
Figure 8
TT
TT
Table 1able 1
able 1able 1
able 1
SEUQROTGNINETHGITDEDNEMMOCER
LEDOMEBCMF.ONMETIEUQROTGNINETHGIT
41-01121]bl-ni22[mN5.2
41-01141]bl-ni5.01[mN2.41
91-03121]bl-ni22[mN5.2
91-03141]bl-ni5.42[mN2.33
42-03121]bl-ni63[mN0.4
42-03141]bl-ni5.42[mN2.33
82-78 ]bl-ni2.71[mN3.32
82-721]bl-ni63[mN0.4
83-78 ]bl-ni2.71[mN3.32
83-721]bl-ni63[mN0.4
83-88 ]bl-ni4.13[mN6.24
83-821]bl-ni63[mN0.4
24-88 ]bl-ni4.13[mN6.24
24-821]bl-ni63[mN0.4
11
12
12
11
Insert screwdriver to
remove second split
Friction Facing
®
DIST. AUTORIZADO
MEX (55) 53 63 23 31
QRO (442) 1 95 72 60
MTY (81) 83 54 10 18
