Next 889964 User manual

Tools Needed
Helpline
If you have any problems with this product or require
any replacement fittings please contact Customer
Services Tel: [phone]
ASSEMBLY INSTRUCTIONS.
Regrettably self assembly items cannot be returned once assembly is part or fully completed unless the item is
found to be faulty. Should you need to return the unassembled product, please repack in the original packaging.
IMPORTANT
• Carefully check that you have all parts before beginning assembly.
• We suggest you spend a short time reading through this leaflet and then follow the simple step-by-step
instructions.
IMPORTANT - RETAIN FOR FUTURE REFERENCE - READ CAREFULLY.
889964 / 705213 MILANO GLOSS LARGE WALL
889964 / 705213 MILANO GLOSS LARGE WALL 889964 / 705213 MILANO GLOSS LARGE WALL
889964 / 705213 MILANO GLOSS LARGE WALL
CUPBOARD
CUPBOARDCUPBOARD
CUPBOARD
• Made from partical board & MDF with a pvc finish.
PRODUCT INFORMATION
• Keep fittings out of children's reach and keep children well away from the construction area.
• We recommend that the packaging is used to protect the surfaces during assembly.
• A minimum of two persons is required to assemble this product.
• The maximum weight this unit can hold safely is 25 kg.
• All assembly fixings should always be tightened properly and periodically check all fixings and tighten if
necessary.
•Gloss finishes are prone to light surface scratch and it is therefore very
important that you care for this item correctly.
• Made in China.
• Ensure the product is protected with mats and coasters when items are placed on the surfaces, to prevent
scratching or damage.
• Any spills should be removed immediately with a soft clean damp cloth and dried immediately.
• Do not rub or scrub the surface when cleaning.
• For general cleaning, periodically dust with a soft clean lint-free cloth or a soft micro fibre cloth. Please note soft
cloths (including yellow dusters) contain abrasive fibres which can lightly scratch the surface, if in doubt please try
your cloth in an inconspicuous area of the furniture first to assess its suitability. A sample of a suitable cloth for
cleaning is included within the hardware pack
• Never drag pieces of furniture across the floor as this will cause damage to the joints.
• Do not put hot dishes directly on the surfaces of the item.
• Do not use furniture polish.
CARE INSTRUCTIONS
• Avoid keeping furniture in direct sunlight or close to any heat sources as this can cause cracking, discolouration
or warping.
FITTINGS
Page 1 of 7

PARTS
DX24
CX2
BX14AX12 EX24 FX16
(8*30mm)
GX12 HX3 IX8 JX1 KX1
(25mm)
right left
(6*30mm)
LX1
Please note: Remove the protective film after assembly of this product unless it is stated in
the steps to do so - this will prevent accidental scratches during assembly
1. Insert 24 x cambolts (E) into panels 1, 2, 5 & 6 and
tighten with a screwdriver.
STEP TWO
STEP ONE
E
E
2
1
STEP TWO
Page 2 of 7

1. Glue and insert 4 x wooden dowels (A) into panel 1
and attach panels 7(x4) to panel 1.
2. Insert 4 x camlocks (D) into panels 7(x4) and tighten
with a screwdriver.
Ensure the arrow indicator is pointing towards the
panel edge and ensure the assembly bolt locates
properly into the camlock before turning
1. Glue and insert 5 x wooden dowels (B) into panel 4
and attach panel 4 to panel 1.
2. Insert 4 x camlocks (D) into panel 4 and tighten with
a screwdriver.
Ensure the arrow indicator is pointing towards the
panel edge and ensure the assembly bolt locates
properly into the camlock before turning
STEP THREE
D
A
1
7
C
B
4
B
D
D
D
D
1. Glue and insert 4 x wooden dowels (A) into panels
7(x4) .
2. Glue and insert 5 x wooden dowels (B) into panel 4
and attach panel 2 to panels 4 & 7(x4).
3. Insert 8 x camlocks (D) into panels 7(x4) & 4 and
tighten with a screwdriver.
Ensure the arrow indicator is pointing towards the
panel edge and ensure the assembly bolt locates
properly into the camlock before turning
STEP FOUR
STEP FIVE
B
1
C
D
B
B
B
B
B
A
A
A
A
D
D
STEP FIVE
Page 3 of 7

1. Glue and insert 4 x wooden dowels (B) into panels 5
& 6
2. Glue and insert 4 x wooden dowels (A) into panels 5
& 6 and attach panels 5 & 6 to panels 1, 2 & 4.
3. Insert 8 x camlocks (D) into panels 1 & 2 and tighten
with a screwdriver.
Ensure the arrow indicator is pointing towards the
panel edge and ensure the assembly bolt locates
properly into the camlock before turning
1. Use 16 x stickers (F) to cover the camholes .
STEP SIX
2
1
6
5
A
A
B
A
1
2
7
7
1. Attach 3 x hinges (H) to panel 3 with 6 × screws (G)
by using a screwdriver until tight.
2. Attach panel 3 to panel 2 with 6 × screws (G)
through 3 x hinges (H) by a screwdriver.
To align doors use the adjustment diagram
below.
LATERAL
VERTICAL
FRONT- TO-BACK
STEP SEVEN
STEP
EIGHT
2
7
STEP
EIGHT
Page 4 of 7

1. Attach hinge (J) to panels 3 & 6 with 4 × screws (I)
by using a screwdriver until tight.
2. Attach hinge (K) to panels 3 & 5 with 4 × screws (I)
by using a screwdriver until tight.
1. Use the template (L) provided to mark on the wall
the position of the fixings.
NB: Place the template over the back of the wall unit to
STEP NINE
NB: Place the template over the back of the wall unit to
ensure that the holes match the position of the hooks
before drilling into your wall
2. Use a spirit level to check that the fixings are level .
3. Drill four holes and insert an appropriate wall plug
into each. Insert the screws and tighten,leaving the
screw head exposed by about 1/4 inch(6mm)
Warning:
Always ensure intended wall area to be drilled is
free from hidden electrical wires, water and gas
pipes.
NB: Wall fixings are not included - please source
suitable fixings for your wall type. If in doubt
please consult a qualified trades person.
STEP TEN
PLEASE SELECT WHICH ORIENTATION YOU WANT THE UNIT TO BE HANG ON THE WALL.
STEP TEN
Page 5 of 7

1. Lift the wall cupboard into position ensuring that
the fixing clips attached to the wall are firmly hooked
over the screw heads. Check the wall unit periodically
to see that no fitting has loosened and needs
attention.
2
3
1. Use the template (L) provided to mark on the wall
the position of the fixings.
NB: Place the template over the back of the wall unit to
ensure that the holes match the position of the hooks
before drilling into your wall
2. Use a spirit level to check that the fixings are level .
3. Drill four holes and insert an appropriate wall plug
into each. Insert the screws and tighten,leaving the
screw head exposed by about 1/4 inch(6mm)
Warning:
Always ensure intended wall area to be drilled is
free from hidden electrical wires, water and gas
pipes.
NB: Wall fixings are not included - please source
suitable fixings for your wall type. If in doubt
please consult a qualified trades person.
STEP TWELVEN
PLEASE SELECT WHICH ORIENTATION YOU WANT THE UNIT TO BE HANG ON THE WALL.
STEP ELEVEN
N
E
X
T
PLEASE SELECT WHICH ORIENTATION YOU WANT THE UNIT TO BE HANG ON THE WALL.
Page 6 of 7

1. Lift the wall cupboard into position ensuring that the fixing clips attached to the wall are firmly hooked over the
screw heads. Check the wall unit periodically to see that no fitting has loosened and needs attention.
5
3
6
3
Next Retail Ltd, Desford Road, Leicester, LE19 4AT
Page 7 of 7