Next 892041 User manual

Tools Needed
Helpline
If you have any problems with this product or require
any replacement fittings please contact Customer
Services Tel: [phone]
ASSEMBLY INSTRUCTIONS.
Regrettably self assembly items cannot be returned once assembly is part or fully completed unless the item is found
to be faulty. Should you need to return the unassembled product, please repack in the original packaging.
IMPORTANT
IMPORTANT - RETAIN FOR FUTURE REFERENCE - READ CAREFULLY.
892041 MODE WALL UNIT
892041 MODE WALL UNIT 892041 MODE WALL UNIT
892041 MODE WALL UNIT
IMPORTANT
• Carefully check that you have all parts before beginning assembly.
• We suggest you spend a short time reading through this leaflet and then follow the simple step-by-step
instructions.
• Made from partical board with a wood effect finish.
CARE INSTRUCTIONS
PRODUCT INFORMATION
• All assembly fixings should always be tightened properly and periodically check all fixings and tighten if necessary.
• Please do not apply adhesive substrates for example , sticky tape to the product.
• Keep fittings out of children's reach and keep children well away from the construction area.
• Avoid keeping furniture in direct sunlight or close to any heat sources as this can cause cracking, discolouration or
warping.
• Any spills should be removed immediately with a soft clean damp cloth and dried immediately.
• Made in China.
• Do not put hot dishes directly on the surfaces of the item.
• Ensure the product is protected with mats and coasters when items are placed on the surfaces, to prevent
scratching or damage.
• We recommend that the packaging is used to protect the surfaces during assembly.
• A minimum of two persons is required to assemble this product.
• For general cleaning, periodically dust with a soft cloth.
• Do not rub or scrub the surface when cleaning.
• The maximum weight this unit can hold safely is 20 kg.
• Do not use furniture polish.
Page 1 of 6

PARTS
FITTINGS
1. Insert 16 x cambolts (E) into panels 1 & 2 and tighten
with a screwdriver.
STEP ONE
Page 2 of 6

1. Glue and insert 4 x wooden dowels (B) into panel 3
and attach panels 5 & 7 to panel 3.
1. Glue and insert 2 x wooden dowels (A) into panels
panels 5 & 7 .
2. Glue and insert 3 x wooden dowels (B) into panel 3
and attach panels 3, 5 & 7 to panel 2.
3. Insert 6 x camlocks (D) into panels3, 5 & 7 and
tighten with a screwdriver.
Ensure the arrow indicator is pointing towards the
panel edge and ensure the assembly bolt locates
properly into the camlock before turning
STEP TWO
STEP THREE
properly into the camlock before turning
1. Glue and insert 2 x wooden dowels (A) into panels
6(x2) and attach panels 6(x2) to panel 2 .
2. Insert 2 x camlocks (D) into panels 6(x2) and tighten
with a screwdriver.
Ensure the arrow indicator is pointing towards the
panel edge and ensure the assembly bolt locates
properly into the camlock before turning
STEP FOUR
Page 3 of 6

1. Glue and insert 4 x wooden dowels (A) into panels
panels 5 , 7 & 6 (x2) .
2. Glue and insert 3 x wooden dowels (B) into panel 3
and attach panel 1 to panels 5 , 7 & 6 (x2)
3. Insert 8 x camlocks (D) into panels 3, 5 , 7 & 6 (x2)
and tighten with a screwdriver.
Ensure the arrow indicator is pointing towards the
panel edge and ensure the assembly bolt locates
properly into the camlock before turning
1. Attach 2 x hinges (F) to panel 4 with 4 × screws (G)
by using a screwdriver until tight.
2. Attach panel 4 to panel 2 with 4 × screws (G) through
2 x hinges (F) by a screwdriver.
To align doors use the adjustment diagram
below.
STEP SIX
STEP FIVE
LATERAL
VERTICAL
FRONT- TO-BACK
1. Attach hinge (J) to panels 4 & 7 with 4 × screws (L)
by using a screwdriver until tight.
2. Attach hinge (K) to panels 4 & 5 with 4 × screws (L)
by using a screwdriver until tight.
3. Use 12 x stickers (I) to cover the camholes .
4. Attach 1 x handle (H) to the panel 4 with 2 x bolts
provided
STEP SEVEN
Page 4 of 6

1. Use the template (M) provided to mark on the wall
the position of the fixings.
NB: Place the template over the back of the wall unit to
ensure that the holes match the position of the hooks
before drilling into your wall
2. Use a spirit level to check that the fixings are level .
3. Drill three holes and insert an appropriate wall plug
into each. Insert the screws and tighten,leaving the
screw head exposed by about 1/4 inch(6mm)
Warning:
Always ensure intended wall area to be drilled is
free from hidden electrical wires, water and gas
pipes.
NB: Wall fixings are not included - please source
suitable fixings for your wall type. If in doubt
please consult a qualified trades person.
STEP TEN
STEP ELEVEN
1. Lift the wall unit into position ensuring that the
fixing clips attached to the wall are firmly hooked over
the screw heads. Check the wall unit periodically to see
that no fitting has loosened and needs attention.
PLEASE SELECT WHICH ORIENTATION YOU WANT THE UNIT TO BE HANG ON THE WALL.
STEP ELEVEN
Page 5 of 6

1. Use the template (M) provided to mark on the wall
the position of the fixings.
NB: Place the template over the back of the wall unit to
ensure that the holes match the position of the hooks
before drilling into your wall
2. Use a spirit level to check that the fixings are level .
3. Drill four holes and insert an appropriate wall plug
into each. Insert the screws and tighten,leaving the
screw head exposed by about 1/4 inch(6mm)
Warning:
Always ensure intended wall area to be drilled is
free from hidden electrical wires, water and gas
pipes.
NB: Wall fixings are not included - please source
suitable fixings for your wall type. If in doubt
please consult a qualified trades person.
STEP THIRTEEN
STEP FOURTEEN
1. Lift the wall unit into position ensuring that the
fixing clips attached to the wall are firmly hooked over
the screw heads. Check the wall unit periodically to see
that no fitting has loosened and needs attention.
STEP FOURTEEN
PLEASE SELECT WHICH ORIENTATION YOU WANT THE UNIT TO BE HANG ON THE WALL.
Next Retail Ltd, Desford Road, Leicester, LE19 4AT
Next Retail Ltd, Desford Road, Leicester, LE19 4AT
Page 6 of 6