Next 894890 User manual

Tools Needed
Helpline
If you have any problems with this product or require
any replacement fittings please contact Customer
Services Tel: [phone]
•Do not use abrasive cleaning products or those containing silicone.
•Any spills should be removed immediately with a soft clean damp cloth and dried immediately.
•Avoid keeping furniture in direct sunlight or close to any heat sources as this can cause cracking, discolouration.
•Never drag pieces of furniture across the oor as this will cause damage to the joints.
•All assembly xings should always be tightened properly and periodically check all xings and tighten if necessary.
•Made in China.
•A mattress measuring 135cm x 190cm is intended for use with this bed.
CARE INSTRUCTIONS
•For general cleaning, periodically dust with a soft cloth.
•Do not rub or scrub the surface when cleaning.
•Keep ttings out of children's reach and keep children well away from the construction area.
•We recommend that the packaging is used to protect the surfaces during assembly.
•A minimum of 2 persons is required to assemble this product.
PRODUCT INFORMATION
•Made from metal with a powder coating nishing.
ASSEMBLY INSTRUCTIONS.
IMPORTANT - RETAIN FOR FUTURE REFERENCE - READ CAREFULLY.
Regrettably self assembly items cannot be returned once assembly is part or fully completed unless the item is found
to be faulty. Should you need to return the unassembled product, please repack in the original packaging.
IMPORTANT
•We suggest you spend a short time reading through this leaet and then follow the simple step-by-step instructions.
•Carefully check that you have all parts before beginning assembly.
894890 SB BEATRICE BED - DOUBLE
Page 1 of 6

1. Attach 2 x side rails (3) to headboard (1) and
footboard (2) with 8 x bolts (A), 8 x washers (C) and 8
x rubber washers (D) using allen key (E) to tighten.
1. Attach 2 x support rails (5) to centre rail (4) with 4
x bolts (A) and 4 x washers (C) using allen key (E) to
tighten.
2. Attach 2 x support legs (6) to centre rail (4) with 2 x
bolts (B) and 2 x washers (C) using allen key (E) to
tighten.
STEP TWO
FITTINGS
PARTS
STEP ONE
Page 2 of 6

3. Attach assembled support rails (5) to assembled
side rails (3) with 4 x bolts (A), 4 x washers (C) using
allen key (E) and tighten.
1. Insert 30 x plastic end caps (9) onto the edge of
each wooden slat assembly (7) . Ensure the curves of
the slats are facing upwards and the pins of the caps
facing downwards.
1. Attach 15 x slat centre caps (8) onto the ends of
each slat assembly already part assembled. Firmly
press in place the caps into the holes in the side and
centre rails. Ensure the curve of the slats facing
upwards.
2. Ensure the end of the straps are wrapped around
support rails (5) tightly.
STEP THREE
STEP FOUR
STEP FIVE
Page 3 of 6

IMPORTANT: Once the feet (part 6) have been
assembled and attached they should be adjusted to
ensure they do not touch the floor (5mm above floor)
to allow for movement once the mattress is placed
on the bed frame.
It is important to note that when moving the bed
ensure that it is not dragged into its new position to
prevent the possibility of these feet being twisted or
angled to one side which could lead to the collapse
of th centre of the bed.
Remove the mattress and lift the bed into its new
position to aviod damaging the bed. Ensure the feet
are at 90۫ to the floor before replacing the mattress.
Next Retail Ltd, Desford Road, Leicester, LE19 4AT
STEP SIX
STEP SEVEN
Page 4 of 6

Page 5 of 6

Page 6 of 6