Next ASHTON 794415 User manual

Tools Needed
Helpline
If youhave any problems with this product or require
any replacement fittings please contact Customer
Services Tel: [phone]
• Ensure the product is protected with mats and coasters when items are placed on the surfaces, to prevent scratching
or damage.
• Do not put hot dishes directly on the surfaces of the item.
• Avoid keeping furniture in direct sunlight or close to any heat sources as this can cause cracking, discolouration or
warping.
• Never drag pieces of furniture across the floor as this will cause damage to the joints.
• Gloss finishes are prone to light surface scratching and it is therefore very important that you care for
this item correctly.
• All assembly fixings should always be tightened properly and periodically check all fixings and tighten if necessary.
• A minimum of two persons is required to assemble this product.
• We recommend the use of the wall attachment bracket/strap provided for safety reasons.
PRODUCT INFORMATION
• Made from MDF material.
• For general cleaning, periodically dust with a soft cloth.
• Do not rub or scrub the surface when cleaning.
• Do not use furniture polish.
• Any spills should be removed immediately with a soft clean damp cloth and dried immediately.
• Made in China.
ASSEMBLY INSTRUCTIONS.
IMPORTANT - RETAIN FOR FUTURE REFERENCE - READ CAREFULLY.
Regrettably self assembly items cannot be returned once assembly is part or fully completed unless the item is found
to be faulty. Should youneed to return the unassembled product, please repack in the original packaging.
IMPORTANT
• We suggest you spend a short time reading through this leaflet and then follow the simple step-by-step instructions.
• Carefully check that you have all parts before beginning assembly.
• Keep fittings out of children's reach and keep children well away from the construction area.
• We recommend that the packaging is used to protect the surfaces during assembly.
CARE INSTRUCTIONS
794415 ASHTON SIDE TABLE
Page 1 of 6

PARTS
FITTINGS
Page 2 of 6

1. Insert 4 x dowels C into top panel (1), insert 4 x
cambolts Ainto top panel (1) with a screwdriver, and
attach drawer stop O to top panel (1) using 1 x screw J
with a screwdriver.
2. Insert 4 x dowels C into base (6), and insert 4 x
cambolts Ainto base (6) with a screwdriver.
3. Attach magnet catch K to side panel (2) using 2 x
screw L with a screwdriver, insert 1 x dowel C into side
panel (2), and insert 1 x cambolt A into side panel (2)
with a screwdriver.
4. Insert 1 x dowel C into side panel (3), insert 1 x
cambolt A into side panel (3) with a screwdriver, and
attach 2 x hinge I to side panel (3) using 8 x screw J
with a screwdriver as shown.
5. Attach 4 x handles D to door (7) using 8 x screw E
with a screwdriver.
6. Attach 2 x hinge H to door (7) using 4 x screw J with
a screwdriver, and attach flat washer M to door (7)
using screw N with a screwdriver.
STEP ONE
Page 3 of 6

1. Attach 2 x handles D to drawer front (8) using 4 x
screws E with a screwdriver.
2. Insert 4 x cambolts A into drawer front (8) with a
screwdriver.
3. Attach drawer side panel (9) & (10) to drawer front
(8) using 4 x cam-locks B with a screwdriver. Ensure
the arrow indicators are pointing to the panel edges
and ensure the cambolts locate properly into the cam-
locks before tightening with a screwdriver.
4. Slide drawer bottom (12) to the unit and attach
drawer back panel (11) to the unit using 4 x screws F
with a screwdriver.
1. Attach rail (4) to side panel (2) & (3) using 2 x
cam-locks B. Ensure the arrow indicators are pointing to
the rail edges and ensure the cambolts locate properly
into the cam-locks before tightening with a screwdriver.
2. Attach above assembled unit to base (6) using 4 x
cam-locks B. Ensure the arrow indicators are pointing to
the panel edges and ensure the cambolts locate properly
into the cam-locks before tightening with a screwdriver.
STEP TWO
STEP THREE
Page 4 of 6

1. Attach top panel (1) to the unit using 4 x cam-locks
B. Ensure the arrow indicators are pointing to the panel
edges and ensure the cambolts locate properly into the
cam-locks before tightening with a screwdriver.
1. Attach back panel (13) to the unit using 11 x screws
Q with a screwdriver.
1. Insert 4 x shelf pins G to both side panels and put
the shelf panel (5) onto them as shown.
STEP FOUR
STEP FIVE
STEP SIX
Page 5 of 6

1. Attached door (7) to the unit as shown.
2. Adjust hinges to the correct positions refer to
diagrams,then tighten screws with a screwdriver.
1. Push the drawer into the unit.
2. Insert paper cards P into both handles as shown.
1. Fasten wall strap S and flat washer R to the back end
of the top panel using 1 x screw Q with a screwdriver.
2. Move the table into the required position and fasten
the loose end of the wall strap to the wall using a
suitable screw and rawl plug for your wall type.
WARNING: Always ensure the area to be drilled is free
from hidden electrical wires and water or gas pipes.
Next Retail Ltd, Desford Road, Leicester, LE19 4AT
STEP SEVEN
STEP EIGHT
NOTE: Wall fixings are not included, source suitable
fixings for your wall type. If in doubt consult a qualified
tradesperson.
STEP NINE
Page 6 of 6