Next ASHER 864240 User manual

Tools Needed
Helpline:
If you have any problems with this product or
require any replacement fittings please contact
Customer Services Tel: [phone]
• Ensure the product is protected with mats and coasters when items are placed on the surfaces, to
prevent scratching or damage.
• Do not rub or scrub the surface when cleaning.
FITTINGS
• Do not put hot dishes directly on the surfaces of the item.
• Never drag pieces of furniture across the oor as this will cause damage to the joints.
• All assembly xings should always be tightened properly and periodically check all xings and tighten if
necessary.
• Avoid keeping furniture in direct sunlight or close to any heat sources as this can cause cracking,
discolouration or warping.
• Made in China.
CARE INSTRUCTIONS
• For general cleaning, periodically dust with a soft cloth.
• Do not use abrasive cleaning products or those containing silicone.
• Any spills should be removed immediately with a soft clean damp cloth and dried immediately.
• We recommend that the packaging is used to protect the surfaces during assembly.
• We suggest you spend a short time reading through this leaet and then follow the simple step-by-step
instructions.
• A minimum of persons persons is required to assemble this product.
PRODUCT INFORMATION
• Made from steel with a nickel plated nish and poplar sprung wooden slats.
ASSEMBLY INSTRUCTIONS.
IMPORTANT - RETAIN FOR FUTURE REFERENCE - READ CAREFULLY.
Regrettably self assembly items cannot be returned once assembly is part or fully completed unless the
item is found
to be faulty. Should you need to return the unassembled product, please repack in the original packaging
IMPORTANT
• Carefully check that you have all parts before beginning assembly.
• Keep ttings out of children's reach and keep children well away from the construction area.
ASHER NICKEL BED 864240
Page 1 of 5

STEP ONE
PARTS
A.Boltsx12
M6X20mm
G.Spanner x 1
11mm
B.Boltsx4
M6X55mm
D.Plastic Washer x8
M6
C.Nutx2
M6
F.Allen key x 1
4mm
E.Metal Washer x 18
M6
(1)Headboard x 1
(2)Tootboard x
(3)Side Rail x 2
(5)Center Rail x 1
(4)Cross Bar x 2
(6)Headboard x 26
(7)Plastic cap (one
(9)Finials x 4
(10)Fabric x 2
(11)Supporting x 2
(8)Plastic cap
(two end open)
Page 2 of 5

1. Attach side rails 3 (x2) to headboard 1 and
footboard 2 using 8 x bolts (A), 8 x plastic
washers (D)
and 8 x metal washers (E). Tighten using Allen
key (F).
1. Attach cross bars 4 (x2) to the brackets on
side rails 3 (x2) using 4 x bolts (A) and 4 x metal
washers (E). Tighten with Allen key (F).
NOTE: Ensure the threaded insert holes in cross
bars 4 (x2) are facing downwards.
1. Attach centre rail 5 between the brackets on
cross bars 4 (x2) using 2 x bolts (B), 4 x metal
washers (E) and 2 x nuts (C). Tighten with Allen
key (F) and spanner (G).
NOTE: Please ensure that the slat cap holes on
the centre rail 5 face upwards.
STEP THREE
STEP TWO
Page 3 of 5

1. Attach support legs 11 (x2) to centre rail 5
using 2 x bolts (B) and 2 x metal washers (E).
Tighten with Allen key (F).
IMPORTANT
Once the feet have been assembled and
attached, they should be adjusted to ensure they
do not touch the floor, (5mm above the floor) to
allow for movement once the mattress is placed
on the bed frame.
It is important to note that when moving the bed
that it is not dragged into its new position to
prevent the possibility of these feet being
twisted or angled to one side, which could lead
to the collapse of the centre of the bed.
To move the bed, remove the mattress and lift
the bed into its new position to avoid damage.
Ensure the feet are at 90° to the floor before
replacing the mattress.
1. Insert a sprung wooden slat 6 through the first
hole in strap 10. Repeat using another sprung
wooden slat 6 and the other strap 10.
2. Attach single sided slat cap 7 onto one end of
the sprung wooden slat 6. Attach another single
sided slat cap 7 onto the other end of the second
sprung wooden slat 6.
3. Attach both sprung wooden slats to the
assembled bed base by inserting each single
sided slat cap 7 into side rails 3 (x2) and using
double sided slat cap 8 in the centre. Once each
slat has been inserted into the slat caps, ensure
the double sided slat cap is firmly pushed into
the holes in centre rail 5.
4. Repeat process for all remaining slats and
caps until all components have been used and
firmly pushed in place.
STEP FOUR
STEP SIX
STEP FIVE
Page 4 of 5

1. Attach finials 9 (x4) to headboard 1 and
footboard 2 turning clockwise by hand to
tighten.
Next Retail Ltd, Desford Road, Leicester, LE19 4AT
STEP SEVEN
Page 5 of 5