Next MILANO 874751 User manual

Tools Needed
Helpline
If you have any problems with this product or require
any replacement fittings please contact Customer
Services Tel: [phone]
ASSEMBLY INSTRUCTIONS
Regrettably self assembly items cannot be returned once assembly is part or fully completed unless the item is found
to be faulty. Should you need to return the unassembled product, please repack in the original packaging.
IMPORTANT
• Carefully check that you have all parts before beginning assembly.
• We suggest you spend a short time reading through this leaflet and then follow the simple step-by-step instructions.
IMPORTANT - RETAIN FOR FUTURE REFERENCE - READ CAREFULLY
874751 MILANO WHITE GLOSS COFFEE TABLE
874751 MILANO WHITE GLOSS COFFEE TABLE874751 MILANO WHITE GLOSS COFFEE TABLE
874751 MILANO WHITE GLOSS COFFEE TABLE
PRODUCT INFORMATION
• Carefully check that you have all parts before beginning assembly.
• Keep fittings out of children's reach and keep children well away from the construction area.
CARE INSTRUCTIONS
• Never drag pieces of furniture across the floor as this will cause damage to the joints.
• Do not rub or scrub the surface when cleaning.
• Any spills should be removed immediately with a soft clean damp cloth and dried immediately.
• Do not put hot dishes directly on the surfaces of the item.
• Avoid keeping furniture in direct sunlight or close to any heat sources as this can cause cracking, discolouration or
warping.
• We recommend that the packaging is used to protect the surfaces during assembly.
• Made from PB,MDF,hollow board & Honeycomb board with a pvc foil & a wood effect finish.
• Made in China.
• A minimum of two persons is required to assemble this product.
• Do not use furniture polish.
• For general cleaning, periodically dust with a soft clean lint-free cloth or a soft micro fibre cloth. Please note soft
cloths (including yellow dusters) contain abrasive fibres which can lightly scratch the surface, if in doubt please try
your cloth in an inconspicuous area of the furniture first to assess its suitability. A sample of a suitable cloth for
cleaning is included within the hardware pack
•Gloss finishes are prone to light surface scratch and it is therefore very important
that you care for this item correctly.
• Ensure the product is protected with mats and coasters when items are placed on the surfaces, to prevent
scratching or damage.
• All assembly fixings should always be tightened properly and periodically check all fixings and tighten if necessary.
Page 1 of 8

FITTINGS
PARTS
DX30
CX2
BX10AX20 EX30
FX12
(? 8*30mm) (? 6*30mm)
HX4 IX1 JX9
GX2
(4*38mm)
Please note: Remove the protective film after assembly of this product - this will prevent
accidental scratches during assembly
1. Attach panels 15(x2), 16(x2) & 17(x2) to panels
13(x2) with 12 x screws (F) and tighten with a
screwdriver.
STEP ONE
Page 2 of 8

1.Slide panels 14(x2) into the assembled drawer
frame.
1. Insert 3 x cambolts (E) into panel 11 and tighten
with a screwdriver.
2. Glue(C) and insert 3 x wooden dowels (B) into
panels 15, 16 & 17.
3. Attach panel 11 to the assembled drawer frame.
4. Insert 3 x camlocks (D) into panels 15, 16 & 17 and
tighten with a screwdriver.
Ensuring the arrow indicator is pointing towards the
panel edge before tightening with a screwdriver.
STEP TWO
STEP THREE
panel edge before tightening with a screwdriver.
1. Insert 3 x cambolts (E) into panel 12 and tighten
with a screwdriver.
2. Glue(C) and insert 3 x wooden dowels (B) into
panels 15, 16 & 17.
3. Attach panel 12 to the assembled drawer frame.
4. Insert 3 x camlocks (D) into panels 15, 16 & 17 and
tighten with a screwdriver.
Ensuring the arrow indicator is pointing towards the
panel edge before tightening with a screwdriver.
STEP FOUR
B
C
Page 3 of 8

1. Insert 14 x cambolts (E) into panels 3(x2), 1 & 2 and
tighten with a screwdriver.
1. Glue and insert the 2 x wooden dowels (B) into
panel 1.
2. Attach panel 6 to panel1.
3. Insert 2 x camlocks (D) into panel 6 and tighten with
a screwdriver.
Ensuring the arrow indicator is pointing towards the
panel edge before tightening with a screwdriver.
STEP SIX
STEP FIVE
C
D
D
6
B
2
1
3x2pcs
E
E
E
E
E
1. Glue and insert the 6 x wooden dowels (A) into
panels 7, 8 & 9.
2. Attach panels 7, 8 & 9 to panel 1.
3. Insert 2 x camlocks (D) into panel 7 and tighten with
a screwdriver.
Ensuring the arrow indicator is pointing towards the
panel edge before tightening with a screwdriver.
STEP SEVEN
D
1
B
1
9
8
7
D
A
C
A
A
C
Page 4 of 8

1. Glue(C) and insert 4 x wooden dowels (A) into panel
10.
2. Attach panel 10 to panels 8 & 9.
Please note: There is a choice of Walnut effect or
white gloss for the panel 10. The colour you prefer
needs to face up upwards & outwards.
1. Insert 4 x camlocks (D) into panels 8 & 9 and
tighten with a screwdriver.
Ensuring the arrow indicator is pointing towards the
panel edge before tightening with a screwdriver.
STEP NINE
STEP EIGHT
8
1. Glue(C) and insert 4 x wooden dowels (B) into
panel 6.
2. Attach panel 2 to panels 6, 7, 8 & 9.
3. Insert 2 x camlocks (D) into panel 6 and tighten with
a screwdriver.
Ensuring the arrow indicator is pointing towards the
panel edge before tightening with a screwdriver.
STEP TEN
9
D
D
D
D
B
C
Page 5 of 8

1. Fix panel 2 to panels 7, 8 & 9 with 8 x screws (J)
and tighten with an Allen key (I).
1. Insert 10 x cambolts (E) into panel 2 and tighten
with a screwdriver.
STEP ELEVEN
STEP TWELVE
J
I
JJ
2
9
7
8
2
1. Glue(C) and insert 4 x wooden dowels (A) into
panels 4(x2).
2. Attach panels 3(x2) to panels 4(x2).
3. Insert 4 x camlocks (D) into panels 4(x2) and tighten
with a screwdriver.
Ensuring the arrow indicator is pointing towards the
panel edge before tightening with a screwdriver.
STEP THIRTEEN
2
Page 6 of 8

1. Glue(C) and insert 6 x wooden dowels (A) into panel
2.
2. Attach assembly frame to panel 2.
3. Insert 10 x camlocks (D) into panels 4(x2) & 3(x2)
and tighten with a screwdriver.
Note :Please note the gloss pvc foil must be faced
outside when assembling.
Ensuring the arrow indicator is pointing towards the
panel edge before tightening with a screwdriver.
1. Carefully turn over this assembly unit by two
person
2. Insert 4 x fittings (H) into the required position .
3. Insert pane 5 onto the fittings (H) .
Please note: There is a choice of Walnut effect or
white for the panel 5. The colour you prefer needs to
STEP FORTEEN
STEP FIFTEEN
1
white for the panel 5. The colour you prefer needs to
face up upwards.
1. Insert the assembled drawers to the unit as
diagram.
2. Use 4 x stickers (G) to cover the camlock holes
STEP SIXTEEN
7
8
5
H
H
11
12
7
Page 7 of 8

1.The assembled coffee table as shown.
STEP SEVENTEEN
Next Retail Ltd, Desford Road, Leicester, LE19 4AT
Page 8 of 8